Tellurium enhanced non-resonant third-order optical nonlinearity in a germano-silicate optical fiber

碲掺杂的高非线性石英光纤

All-optical switching application of germano-silicate optical fiber incorporated with Ag nanocrystals

银纳米晶体掺杂的高非线性石英光纤的全光转换应用

Harmonic Millimeter Wave Generation and Frequency Up-Conversion Using Optical Injection Locking and Brillouin Selective Sideband Amplification

Harmonic millimeter wave (mm-wave) generation and frequency up-conversion are experimentally demonstrated using optical injection locking and Brillouin selective sideband amplification (BSSA) induced by stimulated Brillouin scattering in a 10-km single-mode fiber. By using this method, we successfully generate third-harmonic mm-wave at 27 GHz (f(LO) - 9 GHz) with single sideband (SSB) modulation and up-convert the 2GHz intermediate frequency signal into the mm-wave band with single mode modulation of the SSB modes. In addition, the mm-wave carrier obtains more than 23 dB power gain due to the BSSA. The transmission experiments show that the generated mm-wave and up-converted signals indicate strong immunity against the chromatic dispersion of the fibers.

Electro-Optical Effect Measurement of Thin-Film Material Using PM Fiber Mach-Zehnder Interferometer

A polarization-maintaining (PM) fiber Mach-Zehnder (MZ) interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer,all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here, we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.

High birefringent rhombic-hole photonic crystal fibers

High birefringence induced by rhombic air-hole photonic crystal fibers (PCFs) is numerically analyzed by using the finite-element method. The birefringence of a few kinds of PCFs was investigated with different parameters related to rhombic holes, including the rhombic-hole shape, size, and spacing. It was found that the birefringence of the proposed rhombic-hole PCF in this study is relatively larger than that of an elliptical-hole PCF with the same air-filling fraction (f = 0.0375) when the ratio of the rhombic-hole diagonal length is equal to the elliptical-hole ellipticity. (C) 2010 Optical Society of America

Light-emitting-diode-induced fluorescence detector for capillary electrophoresis using optical fiber with spherical end

A simple fluorescence detector for capillary electrophoresis (CE) using a blue light-emitting-diode (LED) as excitation source is constructed and evaluated. An optical fiber was used to collect the fluorescence, and a flat end of the fiber was modified to spherical end, resulting in 50% increase of efficiency over the flat end. A simple device for optical alignment of the fibers and capillary column was designed. The concentration and mass detection limits for fluorescein were 1.8 x 10(-7) Mol l(-1) and 4.3 femol, respectively. (C) 2002 Elsevier Science B.V. All rights reserved.

Preparation of In2O3 ceramic nanofibers by electrospinning and their optical properties

Electrospinning was employed to fabricate polymer-ceramic composite fibers from solutions containing polyvinyl pyrrolidone (PVP) and In(NO3)(3)center dot 4(1)/2H2O. Upon firing the composite fibers at 800 degrees C, In2O3 fibers with diameters ranging from 200 to 400 nm were synthesized. This indium oxide calcined at 800 degrees C is a body-centered cubic cell. The photoluminescence (PL) properties of the as-formed In2O3 nanofibers were investigated. The In2O3 nanofibers show a strong PL emission in the ultraviolet (UV) region under shorter UV light irradiation.