Vertical Bearing Capacity of a Partially-Embedded Pipeline on Tresca Soils

Slip-line field solutions are presented for the ultimate load of submarine pipelines on a purely cohesive soil obeying Tresca yield criterion, taking into account of pipe embedment and pipe-soil contact friction. The derived bearing capacity factors for a smooth pipeline degenerate into those for the traditional strip-line footing when the embedment approaches zero. Parametric studies demonstrate that the bearing capacity factors for pipeline foundations are significantly influenced by the pipeline embedment and the pipe-soil frictional coefficient. With the increase of pipeline embedment, the bearing capacity factor Nc decreases gradually, and finally reaches the minimum value (4.0) when the embedment equals to pipeline radius. As such, if the pipeline is directly treated as a traditional strip footing, the bearing capacity factor Nc would be over evaluated. The ultimate bearing loads increase with increasing pipeline embedment and pipe-soil frictional coefficient.

装药弹体侵彻混凝土厚靶中的炸药摩擦起爆模型

基于炸药的热爆炸理论,采用炸药的热点温度(也称为临界起爆温度)作为起爆判据,分析了装药弹体在侵彻混凝土厚靶过程中的炸药安全性问题,建立了炸药摩擦起爆的热传导模型.对模型进行了量纲一化分析,得出量纲一热流率幅值Qm与炸药和弹壳界面量纲一温度峰值T′max的关系,以及可在实际工程中应用的临界量纲一控制参数Qmc,同时得到了反映摩擦产生的热量在炸药与弹壳间分配比例关系的量纲一参数ΚⅠ.结果表明,炸药装药和弹壳接触面间的强摩擦是形成热点、从而导致炸药早炸的一个重要因素.

Numerical investigation on a transition prediction model

A new transition prediction model is introduced, which couples the intermittency effect into the turbulence transport equations and takes the characteristics of fluid transition into consideration to mimic the exact process of transition. Test cases include a two-dimensional incompressible plate and a two-dimensional NACA0012 airfoil. Performance of this transition model for incompressible flows is studied, with numerical results consistent to experimental data. The requirement of grid resolution for this transition model is also studied.

MODELING EVOLUTION OF INTERNAL WAVES IN SOUTH CHINA SEA

Internal waves are an important factor in the design of drill operations and production in deep water, because the waves have very large amplitude and may induce large horizontal velocity. How the internal waves occur and propagate over benthal terrain is of great concern for ocean engineers. In the present paper, we have formulated a mathematical model of internal wave propagation in a two-layer deep water, which involves the effects of friction, dissipation and shoaling, and is capable of manifesting the variation of the amplitude and the velocity pattern. After calibration by field data measured at the Continental Slope in the Northern South China Sea, we have applied the model to the South China Sea, investigating the westward propagation of internal waves from the Luzon Strait, where internal waves originate due to the interaction of benthal ridge and tides. We find that the internal wave induced velocity profile is obviously characterized by the opposite flow below and above the pycnocline, which results in a strong shear, threatening safety of ocean structures, such as mooring system of oil platform, risers, etc. When internal waves propagate westwards, the amplitude attenuates due to the effects of friction and dissipation. The preliminary results show that the amplitude is likely to become half of its initial value at Luzon Strait when the internal waves propagate about 400 kilometers westwards.

Motion simulation of annular polishing

Based on the Coulomb friction model, the frictional motion model of workpiece relating to the polishing pad was presented in annular polishing. By the dynamic analysis software, the model was simulated and analysed. The conclusions from the results were that the workpiece did not rotate steadily. When the angular velocity of ring and the direction were the same as that of the polishing pad, the angular velocity of workpiece hoicked at the beginning and at the later stage were the same as that of the polishing pad before contacting with the ring. The angular velocity of workpiece vibrated at the moment of contacting with the ring. After that the angular velocity of workpiece increased gradually and fluctuated at a given value, while the angular velocity of ring decreased gradually and also fluctuated at a given value. Since the contact between the workpiece and the ring was linear, their linear velocities and directions should be the same. But the angular velocity of workpiece was larger than that of the polishing pad on the condition that the radius of the workpiece was less than that of the ring. This did not agree with the pure translation principle and the workpiece surface could not be flat, either. Consequently, it needed to be controlled with the angular velocity of ring and the radii of the ring and the workpiece, besides friction to make the angular velocity of workpiece equal to that of the polishing pad for obtaining fine surface flatness of the workpiece. Copyright © 2007 Inderscience Enterprises Ltd.}

环形抛光中工件形状对抛光速度的影响

本文基于库仑摩擦模型，模拟了不同形状的工件在环形抛光的运动。从结果可知，（1）如果工作环处于自由转动状态，工件的角速度在环形抛光中比抛光盘的角速度大；（2）可通过控制工作环的角速度使工件和抛光盘的角速度同步。工作环的角速度依赖于工作环和工件的半径、抛光盘－工件和抛光盘－工作环的摩擦系数，以及抛光盘的角速度；（3）有尖角的工件与工作环的接触处于不连续状态，导致二者的接触状态发生变化和工件角速度的波动。