Characteristics of AlGaN/GaN HEMTs Grown by Plasma-Assisted Molecular Beam Epitaxy

AlGaN/GaN high electron mobility transistor (HEMT) materials are grown by RF plasma-assisted molecular beam epitaxy (RF-MBE) and HEMT devices are fabricated and characterized. The HEMT materials have a mobility of 1035cm~2/(V ? s) at sheet electron concentration of 1.0 * 10~(13)cm~(-2) at room temperature. For the de-vices fabricated using the malt-rials,a maximum saturation drain-current density of 925mA/mm and a peak extrinsic iransecmductance of IHfimS/mm are obtained on devices with gate length and width of l/-im and 80/im respectively. The f_t, unit-current-gain frequency of the devices,is about 18. 8GHz.

Effects of Rapid Thermal Annealing on OpticalProperties of GaInNAs/ GaAs Single Quantum Well Grown by Plasma- Assisted Molecular Beam Epitaxy

国家自然科学基金,国家攀登计划

Structural evaluation of polycrystalline silicon thin films by hot-wire-assisted PECVD

Tungsten wires were introduced into a plasma-enhanced chemical vapor deposition (PECVD) system as a catalyzer: we name this technique 'hot-wire-assisted PECVD' (HW-PECVD). Under constant deposition pressure (p(g)), gas flow ratio and catalyzer position, the effects of the hot wire temperature (T-f) on the structural properties of the poly-Si films have been characterized by X-ray diffraction (XRD), Raman scattering and Fourier-transform infrared (FTIR) spectroscopy. Compared with conventional PECVD, the grain size, crystalline volume fraction (X-e) and deposition rate were all enhanced when a high T-f was used. The best poly-Si film exhibits a preferential (220) orientation, with a full width at half-maximum (FWHM) of 0.2 degrees. The Si-Si TO peak of the Raman scattering spectrum is located at 519.8 cm(-1) with a FWHM of 7.1 cm(-1). The X-c is 0.93. These improvements are mainly the result of promotion of the dissociation of SiH4 and an increase in the atomic H concentration in the gas phase. (C) 2001 Elsevier Science B.V. All rights reserved.

Growth and characterization of GaInNAs/GaAs by plasma-assisted molecular beam epitaxy

We have studied the growth of GaInNAs/GaAs quantum well (QW) by molecular beam epitaxy using a DC plasma as the N sourer. The N concentration was independent of the As pressure and the In concentration, but inversely proportional to the growth rate. It was almost independent of T, over the range of 400-500 degreesC, but dropped rapidly when T-g exceeded 500 degreesC. Thermally-activated N surface segregation is considered to account for the strong falloff of the N concentration. As increasing N concentration, the steep absorption edge of the photovoltage spectra of GaInNAs/GaAs QW became gentle, the full-width at half-maximum of the photoluminescence (PL) peal; increased rapidly, and a so-called S-shaped temperature dependence of PL peak energy showed up. All these were attributed to the increasing localized state as N concentration. Ion-induced damage was one of the origins of the localized state. A rapid thermal annealing procedure could effectively remote the localized state. (C) 2001 Elsevier Science D.V. All rights reserved.

Quality improvement of GaInNAs/GaAs quantum wells grown by plasma-assisted molecular beam epitaxy

The optimum growth condition of GaInNAs/GaAs quantum wells (QWs) by plasma-assisted molecular beam epitaxy was investigated. High-resolution X-ray diffraction and photoluminescence (PL) measurements showed that ion damage drastically degraded the quality of GaNAs and GaInNAs QWs and that ion removal magnets can effectively remove the excess ion damage. Remarkable improvement of PL intensity and obvious appearance of pendellosung fringes were observed by removing the N ions produced in the plasma cell. When the growth rate increased from 0.73 to 1.2 ML/s, the optimum growth temperature was raised from 460 degreesC to 480 degreesC and PL peak intensity increased two times. Although the N composition decreased with increasing growth rate, degradation of optical properties of GaInNAs QWs was observed when the growth rate was over 0.92 ML/s. Due to low-temperature growth of GaInNAs QWs, a distinctive reflection high-energy electron diffraction pattern was observed only when the GaAs barrier was grown under lower As-4 pressure. The samples with GaAs barriers grown under lower As-4 pressure (V/III ratio about 24) exhibited seven times increase in PL peak intensity compared with those grown under higher As-4 pressure (V/III ratio about 50). (C) 2001 Elsevier Science B,V. All rights reserved.

Formation and magnetic properties of Fe16N2 films prepared by ion-beam-assisted deposition

Fe-N films containing the Fe16N2 phase were prepared in a high-vacuum system of ion-beam-assisted deposition (IBAD). The composition and structure of the films were analysed by Auger electron spectroscopy (AES) and X-ray diffraction (XRD), respectively. Magnetic properties of the films were measured by a vibrating sample magnetometer (VSM). The phase composition of Fe-N films depend sensitively on the N/Fe atomic arrival ratio and the deposition temperature. An Fe16N2 film was deposited successfully on a GaAs (1 0 0) substrate by IBAD at a N/Fe atomic arrival ratio of 0.12. The gram-saturation magnetic moment of the Fe16N2 film obtained is 237 emu/g at room temperature, the possible cause has been analysed and discussed. Hysteresis loops of Fe16N2 have been measured, the coercive force H-c is about 120 Oe, which is much larger than the value for Fe, this means the Fe16N2 sample exhibits a large uniaxial magnetocrystalline anisotropy. (C) 1998 Elsevier Science B.V. All rights reserved.

小麦抗白粉病新基因PmCD1和抗条锈病基因YrCD的鉴定及分子标记筛选

本研究对自育小麦白粉病抗源“07鉴126”和条锈病抗源CD1437、CD0534-5进行抗性遗传分析和微卫星引物的筛选，建立了与PmCD1和YrCD抗病基因连锁的SSR分子标记，主要研究结果如下： 1.小麦白粉抗源“07鉴126”抗白粉病基因的鉴定和分子标记的建立 品系“07鉴126”对我国目前白粉菌强优势生理小种E09、E11和其它多种小种表现免疫或高度抵抗。Pm-sus是07鉴126的自然突变感病株。利用“07鉴126”和Pm-sus的F2抗病性分离群体进行抗条锈病性遗传分析和分子标记定位，结果表明，“07鉴126”的白粉抗性为显性单基因控制的全生育期抗性，暂命名为PmCD1；并筛选到了与PmCD1共分离的显性SSR分子标记Xbarc183。系谱分析和分子标记分析表明PmCD1来源于荆州黑麦。抗谱分析表明PmCD1不同于已知的黑麦抗白粉基因，是一个新的抗白粉病基因。Xbarc183这一分子标记的建立为PmCD1的分子标记辅助选择和抗病基因累加提供了方便。 2.小麦条锈抗源CD1437抗条锈病基因的鉴定和分子标记的建立 利用对优势条锈菌小种条中32免疫的小麦品系CD1437及其自然突变感病株Yr-sus杂交构建F2、F3抗病性分离群体。抗条锈病性遗传分析结果显示，1437的抗条锈性为显性单基因控制的全生育期抗性，该基因暂命名为YrCD。SSR分析发现，位于1B染色体上的7个SSR标记Xcfd65、Xgwm11、Xgwm18、Xbarc187、Xwmc406、 Xwmc419、Xwmc216依次分布在YrCD的一侧，与YrCD的遗传距离在1.7 cM至9.2 cM。YrCD和YrCH42的等位性分析显示二者可能为等位基因。YrCD和Yr24、Yr26的抗谱相似。系谱分析和分子标记分析表明贵农20是YrCD的供体。本研究推测YrCD、Yr24、Yr26和YrCH42可能是等位基因，并推测Yr-sus是缺失突变体。 3. 小麦条锈抗源CD0534-5抗条锈病基因的鉴定 利用对条中32免疫的小麦抗条锈病品系CD0534-5及其感病重组自交系CD0534-4建立F2抗病性分离群体。抗条锈病性遗传分析表明，CD0534-5的条锈抗性由两对独立的显性主效基因控制。用BSK法分析，发现其中一对基因与SSR分子标记Xgwm11、Xgwm18、Xwmc128、Xwmc419连锁，该基因是来源于贵农20的YrCD。另一抗性基因来源贵农19，是极有利用价值的未知抗性基因。 This study focused on the investigation and identification of a novel powdery mildew resistant gene PmCD1 in wheat lines 07jian126 and stripe rust resistant gene YrCD in wheat lines CD1482 and CD0534-5, and screened SSR markers tightly linked to them. The main results were as follows: 1.Identification and SSR markers screening of a novel powdery mildew PmCD1 in wheat line 07jian126. Using a Pm resistant wheat line 07jian126 and its Pm susceptible mutant, a F2 population was constructed. Pedigree and genetic analyses indicated that the Pm resistance in 07jian126 was tranderred from rye (Secale cereale L.) cv. Jinzhou and was controlled by a single dominant gene. Differential test using 21 Bgt isolates revealed that the Pm resistant gene in 07jian126 is novel and was temporarily designated as PmCD1. A dominant SSR marker Xbarc183/130 bp was found co-segregated with PmCD1 in the F2 population. The diagnostic band of Xbarc183/130 bp co-segregating with PmCD1 could be used as an ideal marker in marker-assisted-selection during wheat breeding program. 2. Identification and SSR markers mapping of yellow rust resistant gene YrCD in wheat line CD1437. Wheat line CD1437 was highly resistant to predominant Chinese stripe rust race CYR32 at both seedling and adult stages. A F2 population was developed from the cross of CD1437 and its Yr susceptible mutant Yr-sus. Genetic analysis indicated line CD1437 contains a single dominant gene, temporarily designated YrCD. Seven SSR markers on the chromosome 1BS including Xcfd65, Xgwm11, Xgwm18, Xbarc187, wmc406, Xwmc419and Xwmc216 were close linked to YrCD with a genetic dsitance 1.7 cM to 9.2 cM. YrCD came from wheat cultivar Guinong 20. Allelic test of CD1437 and Chinese cultivar Chuanmai 42 indicated that YrCD and YrCH42 were allelic. Reaction patterns of YrCD and Yr24, Yr26 to 21 PST isolates were the same. These results suggested that YrCD and Yr24, Yr26, YrCH42 might be allelic. 3.Detection and identification of yellow rust resistance genes in wheat line CD0534-5 Wheat line CD0534-5 was highly resistant to predominant Chinese stripe rust race CYR32, while its recombinant inbred line CD0534-4 was susceptible. Genetic analysis with a F2 population developed from the cross of CD0534-5 and CD0534-4 indicated line CD0534-5 contains two independent dominant genes. Four SSR markers on the chromosome 1BS including Xgwm11, Xgwm18, Xwmc128, Xwmc419 were found to linked with one gene in CD0534-5. According the locations of makers and pedigree, this gene in CD0534-5 was YrCD, from cultivar Guinong 20. Another resistant gene was from cultivar Guinong 19, different with those genes on 1B such as Yr10, Yr15, Yr5 etc, was a valuable resistant gene in wheat breeding.

糯小麦杂交后代的基因型鉴定及Wx基因的效应研究

糯小麦在食品加工业、淀粉加工业及其它工业上有着重要用途，是近年来许多国家小麦研究的重要课题。国外糯小麦选育尚未突破高产与糯性相结合的难点，国内目前还没有培育出高蛋白强筋型的糯小麦品种，这在一定程度上与缺乏合适的育种方法和高效、实用的糯小麦分子标记辅助育种技术有关。国内外对Wx基因效应的研究主要利用缺体－四体系、重组自交系或近等基因系，还未见有利用遗传背景相同的BC5F2代回交改良群体的报道。 糯性位点近等基因系是小麦淀粉品质育种的重要材料，而我国目前还没有一套中国栽培小麦遗传背景的糯性位点近等基因系。为了选育部分糯小麦、全糯小麦和中国栽培小麦遗传背景的糯性位点近等基因系，我们利用Wx蛋白电泳和高效实用的分子标记技术体系来鉴定糯小麦杂交后代的基因型，结果证明该体系能有效地用于糯小麦的分子标记辅助育种。以中国春糯性位点全套近等基因系为研究材料，对小麦Wx基因的6个STS标记和1个CAPS标记进行了筛选，改良PCR扩增条件以及产物检测方式后，从这些标记中筛选出3个标记，包括鉴定Wx-A1、Wx-D1位点的2个共显性STS标记和Wx-B1位点的1个显性STS标记。利用上述3个分子标记从BC5F2 代回交改良群体中筛选出了8种Wx基因型，经卡方检验，其分离比符合3对基因的分离比例，其中基因型为aabbdd的植株有2株，直链淀粉含量分别为1.81%和0.82%，为全糯小麦；基因型为AAbbdd，aabbDD的部分糯性植株各有1株，直链淀粉含量分别为15.24%和17.57%。以上4株植株的农艺性状和品质性状接近回交亲本“川育12”，并明显优于全糯材料“98Y1441”，表明采用回交法与Wx基因分子标记辅助选择相结合，有助于培育高产、优质的全糯和部分糯小麦。同时，本研究中建立的分子标记技术体系，也为选育具有中国栽培小麦遗传背景的糯性位点近等基因系奠定了基础。 在基因型鉴定的基础上，利用糯小麦杂交后代BC5F2代回交改良群体研究了各基因缺失降低直链淀粉含量的效果和各基因合成直链淀粉的能力，以及直链淀粉含量与农艺性状、品质性状、淀粉糊化特性等的相关性。缺失不同Wx基因的8种基因型，直链淀粉含量差异显著。研究单缺失基因型发现，减少效应最大的是Wx-B1b基因，Wx-B1b和Wx-D1b基因没有显著差异，减少效应最小的是Wx-A1b基因。研究双缺失基因型发现，Wx基因合成直链淀粉的能力，Wx-B1a基因最高，Wx-A1a基因最低，而Wx-B1a和Wx-D1a基因差异很小；直链淀粉含量与株高、穗长、小穗数、穗粒数、千粒重等农艺性状相关不显著，表明淀粉品质育种可以与高产育种实现有机结合；直链淀粉含量与SDS-沉降值呈显著负相关(r=-0.726)，说明直链淀粉含量降低在一定程度上有利于提高小麦营养与加工品质，这一结果至今未见有文献报道；全糯类型的淀粉糊化特性与其他类型显著不同，具有最高的峰值粘度和稀懈值，最低的低谷粘度、最终粘度、反弹值、峰值时间、糊化温度、起始糊化温度，表明糯小麦淀粉在食品和工业上具有特殊用途；稀懈值与直链淀粉含量呈极显著负相关(r=-0.969)，其他粘度参数与直链淀粉含量呈显著正相关(最终粘度r=0.797，低谷粘度r=0.910、反弹值r=0.954、峰值时间r=0.970、糊化温度r=0.962、起始糊化温度r=0.932)。以上结论可为糯小麦品种选育和淀粉品质改良提供理论依据。 Waxy wheat is very important in food processing industry, starch processing industry and the other industries, so it is a focus of wheat research in many countries these years. Foreign wheat breeders have not conquered the difficulty of high yield combined with waxy character, and there is no waxy wheat variety with high protein and strong gluten in China at present，all of which were caused by lacking proper breeding methods and effective, applied molecular markers-assisted selection technique at a certain extent. Until now, research about the effect of waxy genes mainly depended on nullisomic-tetrasomic lines, recombinant lines or near-isogenic lines, and it is lacking the reports of using improved BC5F2 backcross progenies under the common genetic background. Near-isogenic lines at the Wx loci are important materials for wheat starch quality breeding. However, there are no such lines under the Chinese cultivated wheat genetic background. To develop partial waxy wheats, waxy wheats and near-isogenic lines at the Wx loci under the Chinese cultivated wheat genetic background, we use SDS-PAGE of waxy proteins and effective, applied molecular marker-assisted selection technical system to identify the genotype of waxy wheat’s progenies. The results indicated that such a system is applicable in waxy wheat’s molecular marker-assisted selection effectively. A series of Chinese Spring Wx loci near-isogenic lines were used to identify the specific bands of six STS markers and one CAPS marker of Wx genes. After optimizing PCR amplification and separating of PCR products, three co-dominant and dominant STS-markers were identified at the Wx-A1, Wx-D1 and Wx-B1 loci, respectively, which were used to identify the genotype of waxy wheat’s progenies. Eight Wx genotypes were developed from the improved BC5F2 backcross progenies, which follows Mendelian segregation. Among them, there were two aabbdd waxy plants whose amylose content in the BC5F3 seeds were 1.81% and 0.82%, respectively. In addition, there were partial waxy plants (AAbbdd and aabbDD) whose amylose content in the BC5F3 seeds were 15.24 % and 17.57%, respectively. Most agronomic and quality traits of these four plants resembled those of the recurrent parent “Chuanyu 12”, and superior to waxy wheat parent “98Y1441”. This shows that backcross approach in combination with molecular marker-assisted selection of waxy genes is helpful to develop partial and full waxy wheat with good traits in the waxy wheat breeding program. At the same time, molecular marker-assisted selection technical system in this paper, also establish the base for breeding the near-isogenic lines at the Wx loci under the Chinese cultivated wheat genetic background. According to the results of genotype identification, we use waxy wheat’s improved BC5F2 backcross progenies to verify the effects of null alleles on reducing amylose content and determine the amylose synthesis capacity of each Wx gene independently, and investigate the relativity among amylose content with agonomic traits, quality traits, starch pasting properties respectively. There was significant difference in amylose content of the eight genotypes carrying different null Wx alleles. The reducing effect of the single null alleles was the most significant in Wx-B1b, followed by Wx-D1b and Wx-A1b, and there was no significant difference between Wx-B1b and Wx-D1b. The results of the double null lines further demonstrated that for the capacity of amylose synthesis, Wx-B1a was the highest, followed by Wx-D1a and Wx-A1a, and there was no significant difference between Wx-B1a and Wx-D1a. Amylose contents of the eight genotypes were not significantly correlated with plant height, spike length, spikelets per spike, grains per spike, 1000-grain weight, which showed that starch quality breeding could integrate with high yield breeding. Amylose contents of the eight genotypes were negatively significantly correlated with SDS-sedimentation value(r=-0.726), which suggested that reduction in amylose content is propitious to improve quality at a certain extent. Starch pasting properties of the full waxy type was significantly different from the other seven types, with the highest peak viscosity and breakdown, and lowest valley viscosity, final viscosity, setback, peak time, pasting temperature and starting pasting temperature. It indicated that waxy wheat starch has special use in food and industry. Breakdown was negatively significantly correlated with amylose contents (r=-0.969), and the other parameters were positively significantly correlated with amylose contents (r=0.797 for final viscosity, r=0.910 for trough viscosity, r =0.954 for setback, r =0.970 for peak time, r=0.962 for pasting temperature and r=0.932 for starting pasting temperature ). The results of the study are very useful for waxy wheat variety breeding and starch quality improvement.

水稻同源四倍体高代自交系农艺性状分析及遗传差异研究

课题组在不断地创制新的同源四倍体材料的同时，连续多年以提高结实率为目的培育、筛选自交系材料，已获得自交繁殖十二年的高代自交系材料。相对于诱导创制初期，材料表现出的结实率低，同种系单株间的差异较大；高代材料已表现出较显著的结实率提升和较一致的农艺性状表型。 本实验选取课题组多年培育的同源四倍体水稻高代自交系材料，通过形态学、农艺性状和细胞遗传学比较，研究水稻同源四倍体与二倍体之间的异同。结果显示，所有同源四倍体材料的染色体组成均为2N=4X=48，花粉母细胞(PMC)减数分裂行为较正常，99%以上的染色体都能在减数分裂中期I（MI）发生联会、配对，形成四价体和二价体，这与理论染色体组构成相符。在减数分裂过程中，结实率较高的材料染色体异常现象较少而结实率较低的材料染色体异常现象较严重。统计分析表明，二价体和四价体的比例对结实率没有显著影响，但是三价体的数目对结实率有一定影响。这一结果表明了结实率和细胞减数分裂行为可能存在相关性，同源四倍体的减数分裂行为为筛选高结实率的同源四倍体种系提供了依据。 然后，对同源四倍体水稻高代自交系材料进行农艺性状和品质性状的统计与分析。主要针对结实率、每穗实粒数、有效分蘖和穗长等主要农艺性状，以及直链淀粉含量这一重要的品质性状进行统计。将统计结果与1996年诱导加倍的初代材料的数据相对比分析，结果显示所有材料经过多代选育培养，其农艺性状已经有了较显著的提高，同时同源四倍体材料的农艺性状稳定性也有了较显著的提升。如结实率的提高幅度较大，所有材料的平均结实率均显著高于加倍初代，而同种材料不同单株间的结实率差异也显著地减少，变异系数（CV）的平均值由1996年的41.15%减少到了2008年的28.81%。其他重要农艺性状也有不同程度的改良，种内变异系数也相应地降低。此外，实验测量了同源四倍体材料和来源二倍体材料的直链淀粉含量。分析结果显示，部分材料的直链淀粉含量与二倍体亲本产生了较显著的差异，这可能是诱导加倍过程中的遗传变异造成的；同源四倍体材料的种内变异系数（CV）平均值由1996年的6%下降到了2008年的3.88%，显示出在品质性状方面，同源四倍体材料的遗传稳定性也有较显著的增加。同源四倍体材料农艺性状经过多年的选育，表现出一定的提升，同时，经过多年自交纯化，所有材料种系内的性状差异逐渐缩小，说明同源四倍体水稻的遗传稳定性随着自交纯化而增强，这为同源四倍体水稻的进一步选育打下了良好的基础。 最后，通过测量连续两年的自交系材料的遗传多态性，分析材料间遗传差异和种群遗传结构，深入研究连续两代材料间的遗传差异，研究同源四倍体水稻与二倍体材料遗传稳定性之间的差异。实验采用18对SSR微卫星标记对连续两代15个材料，共94份样本进行差异分析。通过扩增条带长度多态性分析，计算不同材料以及同种材料不同世代间的遗传距离，构建同源四倍体和二倍体水稻的分子指纹库，并绘制聚类图。结果显示，同源四倍体和二倍体不同材料间的遗传差异比较大，遗传距离处于0.4757至0.2816之间；而相同品种不同世代材料间的遗传差异较小，但也表现出一定的遗传差异。同种同源四倍体材料不同世代间的遗传差异比二倍体材料更大，两代四倍体材料间遗传距离处于0.1359至0.0485之间；而两代二倍体材料间的遗传距离处于均小于0.0388。结果表明，同源四倍体水稻高代材料具有一定的遗传稳定性，但与来源二倍体材料相比，其世代间的遗传变异性仍然较强。这种结果说明，经过多代的自交纯化培育，同源四倍体水稻材料能够建立起相对稳定的遗传结构，同时，其强于二倍体亲本的变异性有能够为新品种的选育，农艺性状、品质性状的改良提供一定的遗传基础。此外，分析结果表明通过分子标记辅助检验，水稻材料间的遗传多态性能够有效地区分不同的品种，这为水稻品种的分子鉴定提供了一定的依据。 本研究从细胞学鉴定，农艺性状统计分析以及分子标记辅助聚类分析多方面地对同源四倍体水稻高代系进行了研究，对探究同源四倍体水稻的遗传规律，进一步揭示其遗传特性、农艺性状的遗传构成，为进一步选育优质的多倍体水稻提供了一定的理论依据。 This group insists on creating new Autotetraploid Rice (Oryza sativa L.) materials, while improving the seed-setting of them for many years, cultivated and selected the inbred line materials, has obtained the high generation inbred lines after twelve years cultivation. Compared to the early induced materials, which shown the low seed setting, and the large difference between the different plants in the same germ-line; the high generation materials have shown significant improvement in seed setting and more uniform phenotype agronomic traits. The autotetraploid rice high generation inbred lines material, which has been cultivated for more than 12 years, was chose in this experiment. The similarities and differences between autotetraploid and diploid rice was studied through morphological, agronomic and cytogenetic ways. The results showed that all the chromosome of autotetraploid materials are composed of 2N=4X=48, the pollen mother cells (PMC) meiosis behavior is normal, more than 99% chromosomes in metaphase I(MI) were federated and paired to form tetravalents or bivalents, which constitutes a consistent theory of genome. In the meiosis process, the material with a higher seed setting showed less chromosome abnormal than the material whose seed setting is lower. However, statistical analysis showed that the bivalent and tetravalent rate had no significant impact on seed setting, but the number of trivalent had a certain impact on seed setting. The result shows that the seed setting may be related to the meiosis behavior, which provides a basis to cultivate new autotetraploid germ line with high seed setting through the meiotic behavior. Furthermore, the agronomic and quality traits of autotetraploid rice high generation inbred material were statistically analyzed. The statistically analysis was focused on major agronomic traits such as: seed setting, grains per panicle, effective tillers and panicle length, as well as the important quality trait amylose content. The statistic data was compared with the data in 1996, when the first induced generation of autotetraploid material, and the result shows that after a multi-generation breeding, the agronomic traits has been significantly improved in all the materials, while the stability of agronomic traits also significant upgraded. For instant, the seed setting increased significantly, the average seed setting of all materials was significantly higher than the first induced generation, and the differences between different plants in the same species also significantly reduced, the average of the coefficient of variation (CV) was reduced from 41.15% in 1996 to 28.81% in 2008. Other important agronomic traits had improved in different degrees; the coefficient of variation within species is also reduced accordingly. In addition, the amylose content of autotetraploid and diploid materials was measured in this experiment. The results shows that the amylose content of some of the material differed from diploid parents significantly, it may caused by the genetic change during the inducing, autotetraploid materials intra-specific coefficient of variation (CV) average reduced from 6% in 1996 to 3.88% in 2008, shows that this is a significant increase of quality traits stability in autotetraploid rice. Agronomic traits of autotetraploid material shows some improvement after years of breeding, at the same time, after years of purification, all material within the germ-line gradually narrow the differences in traits indicates that autotetraploid rice genetic stability was enhanced, which laid a good foundation for the further autotetraploid rice breeding. Finally, this experiment studied the genetic differences between materials of two generations and researched the difference of genetic stability between diploid and autotetraploid rice materials through investigating the genetic polymorphism, genetic differences between materials and population genetic structure of inbred line materials of two consecutive years.18 pairs of SSR microsatellite markers for 15 materials of two generations were used in this experiment, and the total of 94 samples were analyzed. Through the amplification length polymorphism analysis of different materials and materials in different generations, the genetic distance between materials and generations was analyzed, a diploid and autotetraploid rice molecular fingerprint database and map rendering cluster were constructed. The result shows that the genetic distance is between 0.4757 to 0.2816 among different autotetraploid and diploid materials; the genetic distance between different generations of same species was less, but also shows a certain degree of genetic differences. The inter-generational genetic differences of autotetraploid materials were greater than of the diploid materials, which are 0.1359 to 0.0485 as the genetic distance; comparing with the 0.0388 of diploid materials. The result shows that high generation inbred autotetraploid rice material has a certain genetic stability, but the genetic variation between generations is still strong comparing with the source diploid materials. It indicates that, after many generations of purification cultivation, autotetraploid rice materials established a relatively stable genetic structure, at the same time, stronger variability than its diploid parents are useful in the breeding of new varieties, provides a genetic foundation to the agronomic and quality traits improvement. In addition, the analysis result shows that the through the molecular marker-assisted testing, rice genetic polymorphism between materials can effectively distinguish different species, provides a certain basis for molecular identification of varieties of rice. A series of investigation such as cytological identification, statistical analysis of agronomic traits, molecular marker-assisted cluster analysis was applied in this experiment to research genetic pattern of autotetraploid rice high generation inbred lines, revealed the genetic characteristics and the genetic composition of agronomic traits, provides a theoretical basis for the further selection of high quality autotetraploid rice.

阿佛曼链霉菌的~(12)C离子辐照效应及高产菌株选育；Research on Mutation Breeding of High-producing Strains from Streptomyces Avermitilis Irradiated by Ion Beam of ~(12)C~(6+)

选用12C6+离子辐照诱变阿维菌素B1a产生菌ZJAV-A1,研究其诱变效应。实验结果表明,12C6+离子辐照剂量50Gy时致死率97%,正突变率最高可达到34.2%。通过12C6+离子诱变处理,结合平板培养基及斜面培养基的正突变菌株筛选,最终获得一株稳定性良好,阿维菌素B1a组分产量稳定在4460—4588μg/ml之间,较出发菌株提高11.1%—14.7%的突变株ZJAV-Y1-203。

诱发突变选育小麦新品种的研究探讨；The reseach of wheat variety breeding through radiation

概述了张掖市农科院小麦诱变育种研究的发展历程,介绍了小麦诱变育种的常用方法及辐照处理的参考剂量,并对张掖市小麦诱变育种今后发展的方向进行了探讨。

Template-assisted syntheses of two novel porous zirconium methylphosphonates

Two porous zirconium methylphosphonates (designated as ZMPmi and ZMPme respectively) were synthesized by using dibutyl methylphosphonate (DBMP) as a template. Two efficient post-synthetic treatments were developed to remove the incorporated template without destroying the hybrid structures. The materials were characterized by SEM, EPMA, TG, DTA, FTIR, and NMR. Specific surface area and porosity were evaluated by BET, alpha(s)-plots and DFT methods based on N-2 adsorption-desorption isotherms. The specific surface areas of ZMPmi and ZMPme are determined to be 279 and 403 m(2) g(-1) and the maxima of pore size distributions are at 0.7 and 1.3 nm respectively. (c) 2005 Elsevier Inc. All rights reserved.