5.2 GHz variable-gain amplifier and power amplifier driver for WLAN IEEE 802.11a transmitter front-end

A 5.2 GHz variable-gain amplifier (VGA) and a power amplifier (PA) driver are designed for WLAN IEEE 802.11a monolithic RFIC. The VGA and the PA driver are implemented in a 50 GHz 0.35 μm SiGe BiCMOS technology and occupy 1.12×1.25 mm~2 die area. The VGA with effective temperature compensation is controlled by 5 bits and has a gain range of 34 dB. The PA driver with tuned loads utilizes a differential input, single-ended output topology, and the tuned loads resonate at 5.2 GHz. The maximum overall gain of the VGA and the PA driver is 29 dB with the output third-order intercept point (OIP3) of 11 dBm. The gain drift over the temperature varying from -30 to 85℃ converges within±3 dB. The total current consumption is 45 mA under a 2.85 V power supply.

Nonlinear Optical Properties of AI-Doped nc-Si-SiO_2 Composite Films

The nonlinear optical properties of Al-doped nc-Si-SiO_2 composite films have been investigated using the time-resolved four-wave mixing technique with a femtosecond laser. The off-resonant third-order nonlinear susceptibility is observed to be 1.0 × 10~(-10) esu at 800nm. The relaxation time of the optical nonlinearity in the films is as short as 60fs. The optical nonlinearity is enhanced due to the quantum confinement of electrons in Si nanocrystals embedded in the SiO_2 films. The enhanced optical nonlinearity does not originate from Al dopant because there are no Al clusters in the films.

Effects of Magnetohydrodynamic Interaction-Zone Position on Shock-Wave/Boundary-Layer Interaction

A third-order weighted essentially nonoscillatory and non-free-parameter difference scheme magnetohydrodynamic solver has been established to investigate the mechanisms of magnetohydrodynamics controlling separation induced by an oblique shock wave impinging on a flat plate. The effects of magnetohydrodynamic interaction-zone location on the separation point, reattachment point, separation-bubble size, and boundary-layer velocity profiles are analyzed. The results show that there exists a best location for the magnetohydrodynamic zone to be applied, where the separation point is delayed the farthest, and the separation bubble is decreased up to about 50% in size compared to the case without magnetohydrodynamic control, which demonstrated the promising of magnetohydrodynamics suppressing the separation induced by shock-wave/boundary-layer interactions.

Design of slow extraction system for therapy synchrotron

Based on the optimized design of the lattice for therapy synchrotron and considering the requirement of radiation therapy, the third order resonant extraction is adopted. Using the momentum-amplitude selection method, the extraction system is designed and optimized. An extraction efficiency of more than 97% and a momentum spread less than 0.11% are obtained.

Design of synchrotron for hadron therapy

According to the operation and development of radiation therapy in the world, in order to further promote the radiation therapy of tumour in China, a design of a special synchrotron with two super-periodicity for hadron therapy is presented, including lattice, injection system, RF acceleration and slow extraction of the third order resonance. The synchrotron accelerates the proton beam to 250MeV and the carbon beam to 4000MeV/u.

Preparation and nonlinear optical properties of ultrathin composite films containing both a polyoxometalate anion and a binuclear phthalocyanine

An ultrathin composite film containing both polyoxometalate anion [PMo12O40](3-) ( PMo12) and a planar binuclear phthalocyanine, bi-CoPc, has been prepared by the electrostatic layer-by-layer self-assembly method. UV-vis measurements revealed regular film growth with each four-layer {PMo12/bi-CoPc/PSS/PAH} adsorption. The lm structure was characterized by small-angle X-ray reflectivity measurements, X-ray photoelectron spectra, and AFM images. The nanothick film shows a third-order nonlinear optical response of chi((3)) = 4.21 x 10(-12) esu. Experimental investigations also indicate that the combination of polyoxometalate anions [PMo12O40](3-) with the phthalocyanine bi-CoPc in multilayer films can enhance the third-order NLO susceptibility and modify the third-order NLO absorption of bi-CoPc.

藻体对水环境中N、P及重金属Cu2+、Pb2+、Cd2+、Cr6+的吸附特征研究

随着全球生态环境的恶化，各国日益重视对水体中各种污染物的治理。利用藻类的吸收、富集和降解作用，可以去除污水中的营养物质、重金属离子和有机污染物，与其他物理、化学及工程的方法相比，该技术具有以下优点：成本低、能耗小、治理效果较好，对环境污染小，有利于资源化，有利于整体生态环境的改善，是治理水质污染的新途径。 本文利用几种大型海藻对富营养化海水进行处理，结果发现孔石莼、刚毛藻均有很强的吸收N、P的能力，吸收能力依次为褶曲刚毛藻>束生刚毛藻>孔石莼。水体中褶曲刚毛藻3 g/L含量，在3～5小时之内，可把中等以上富营养化海水中的N、P降低至一类海水水平。利用刚毛藻处理富营养化地下海水和养殖废水，进行海参和大菱鲆养殖试验，探索藻类净化水质和废水循环利用的新模式，使水体保持较低的营养盐状态，减轻养殖废水对环境的影响，实现了海水养殖业与环境的可持续发展。 刚毛藻在我国近海滩涂分布广泛，利用它来处理富营养化水体，并和水产养殖业相结合，既净化水体，使养殖废水能循环利用，满足水产养殖的需求，又改善水产业生态环境。同时，将回收藻体生产优质饲料、食品和药物等，实现藻类资源的高值利用。刚毛藻营养丰富，用其替代鼠尾藻作海参饲料，资源丰富，成本低，效果好，是一种值得加以开发利用的宝贵资源，具有广泛的应用前景。 生物吸附法是一种经济有效的移除废水中有害重金属离子的方法。由于藻类细胞壁中的多聚糖可提供吸附重金属的位点，廉价而蕴藏丰富的海藻对多种重金属表现出很强的吸附能力。所以本文通过分批实验，研究了非活体刚毛藻对水体中重金属Cu2+、Pb2+和Cd2+的吸附影响因子、吸附热力学、吸附动力学及吸附机理，得到了平衡等温线及动力学数据。吸附过程的最佳pH值为5.0，吸附量随温度的升高而增加，水体中常见的Na+、K+、Ca2+、Mg2+阳离子及Cl-、NO3-、SO42-、C2O42-等阴离子的存在对吸附的影响并不显著。EDTA存在时，吸附百分率大大降低。吸附等温线符合Langmuir和Freundlich方程。刚毛藻对重金属Cu2+、Pb2+和Cd2+的吸附容量很高，25℃时，对Cu2+、Pb2+和Cd2+的最大吸附容量分别为1.61 mmol/g、0.96 mmol/g和0.98 mmol/g，且吸附过程为吸热反应。刚毛藻对重金属Cu2+、Pb2+和Cd2+的吸附过程为化学吸附，在吸附过程中藻体表面的官能团可能与金属离子发生了螯合作用。吸附动力学过程符合pseudo-二级动力学模型，在初始的30min内，吸附速率很快，随后速率逐渐降低。解吸试验表明，用EDTA可以对重金属进行回收，刚毛藻可以循环利用。实验结果表明刚毛藻是一种高效、经济实用的生物吸附材料，可用来吸附回收水体中的重金属Cu2+、Pb2+和Cd2+等。 通过非活体刚毛藻对重金属Cr6+的吸附影响因子、吸附动力学、吸附机理的研究发现，刚毛藻对Cr6+具有很强的还原能力，对电镀废水中的Cr6+的还原去除提供了非常好的方法。吸附过程的最佳pH值为2～3，实际电镀废水通常在此pH范围，因此处理实际废水时，首先在原酸性条件下，对Cr6+进行还原去除，然后调废水pH至5.0，继续进行吸附，去除其他二价离子及被还原的三价Cr离子，实现了利用同一材料还原Cr6+为Cr3+，并将Cr3+和其他重金属离子同时去除。通过对机理的讨论，认为刚毛藻对Cr6+的生物吸附过程不是一个简单的“离子交换过程”，而是一个“吸附还原过程”。在海藻量足够的前提下，只要时间足够长，Cr6+可被彻底还原去除。 利用工业废弃物褐藻渣，对水体中重金属离子Cu2+、Pb2+、Cd2+及Cr6+的生物吸附特性分别进行了讨论，结果表明褐藻渣对重金属离子的吸附特性与刚毛藻一致，吸附等温线符合Langmuir和Freundlich方程，在25℃时，pH为5.0时，由Langmuir方程求出褐藻渣对Cu2+、Pb2+和Cd2+的最大吸附容量分别为4.20 mmol/g、3.13 mmol/g和2.97 mmol/g。褐藻渣对低、高浓度的重金属Cr6+都具有很强的吸附能力，且移除效果比较彻底。实际应用结果表明，褐藻渣是一种高效、经济实用的生物吸附材料，可用来吸附回收水体中的重金属离子，具有广泛的应用前景。

Biosorption and desorption of Cd2+ from wastewater by dehydrated shreds of Cladophora fascicularis

The adsorption and desorption of algae Cladophora fascicularis and their relation with initial Cd2+ concentration, initial pH, and co-existing ions were studied. Adsorption equilibrium and biosorption kinetics were established from batch experiments. The adsorption equilibrium was adequately described by the Langmuir isotherm, and biosorption kinetics was in pseudo-second order model. The experiment on co-existing ions showed that the biosorption capacity of biomass decreased with an increasing concentration of competing ions. Desorption experiments indicated that EDTA was efficient desorbent for recovery from Cd2+. With high capacities of metal biosorption and desorption, the biomass of Cladophora fascicularis is promising as a cost-effective biosorbent for the removal of Cd2+ from wastewater.

Sorption and desorption of lead (II) from wastewater by green algae Cladophora fascicularis

Biosorption is an effective method to remove heavy metals from wastewater. In this work, adsorption features of Cladophora fascicularis were investigated as a function of time, initial pH, initial Pb(II) concentrations, temperature and co-existing ions. Kinetics and equilibria were obtained from batch experiments. The biosorption kinetics followed the pseudo-second order model. Adsorption equilibria were well described by the Langmuir and Freundlich isotherm models. The maximum adsorption capacity was 198.5 mg/g at 298 K and pH 5.0. The adsorption processes were endothermic and the biosorption heat was 29.6 kJ/mol. Desorption experiments indicated that 0.01 mol/L Na(2)EDTA was an efficient desorbent for the recovery of Pb(II) from biomass. IR spectrum analysis suggested amido or hydroxy, C=O and C-O could combine intensively with Pb(II). (C) 2006 Elsevier B.V. All rights reserved.

Biosorption of copper (II) and lead (II) from aqueous solutions by nonliving green algae Cladophora fascicularis: Equilibrium, kinetics and environmental effects

Biosorption of Cu2+ and Pb2+ by Cladophora fascicularis was investigated as a function of initial pH, initial heavy metal concentrations, temperature and other co-existing ions. Adsorption equilibriums were well described by Langmuir and Freundlich isotherm models. The maximum adsorption capacities were 1.61 mmol/ g for Cu2+ and 0.96 mmol/ g for Pb2+ at 298K and pH 5.0. The adsorption processes were endothermic and biosorption heats calculated by the Langmuir constant b were 39.0 and 29.6 kJ/ mol for Cu2+ and Pb2+, respectively. The biosorption kinetics followed the pseudo- second order model. No significant effect on the uptake of Cu2+ and Pb2+ by co-existing cations and anions was observed, except EDTA. Desorption experiments indicated that Na(2)EDTA was an efficient desorbent for the recovery of Cu2+ and Pb2+ from biomass. The results showed that Cladophora fascicularis was an effective and economical biosorbent material for the removal and recovery of heavy metal ions from wastewater.

Synthesis and evaluation of a thiourea-modified chitosan derivative applied for adsorption of Hg(II) from synthetic wastewater

In this work, a thiourea-modified chitosan derivative (TMCD) was synthesized through two steps, O-carboxymethylated first and then modified by a polymeric Schiff's base of thiourea/glutaraldehyde. The adsorption behavior of mercury (II) ions onto TMCD was investigated through batch method. The maximum adsorption capacity for Hg(II) was found to be 6.29 mmol/g at pH 5.0 and both kinetic and thermodynamic parameters of the adsorption process were obtained. The results indicated that adsorption process was spontaneous exothermic reaction and kinetically followed pseudo-second-order model. The adsorption experiments also demonstrated TMCD had high adsorption selectivity towards Hg(II) ions when coexisted with Cu(II), Zn(II), Cd(II) and Ca(II) in solution and it could be easily regenerated and efficiently reused. (C) 2010 Elsevier B.V. All rights reserved.

Studies on two coordination polymers [M(mu(4)-pz25dc)](n) (M = Cd or Zn, pz25dc=pyrazine-2,5-dicarboxylato) with three-dimensional pillared-layer three-nodal framework: Synthesis, structural characterization, strong optical non-linearities and optical limiting properties

Two isomorphous new candidates [M(mu(4)-pz25dc)](n) (M = Cd, 1; Zn, 2; pz25dc = pyrazine-2,5-dicarboxylato)for nonlinear optical (NLO) materials have been synthesized hydrothermally and characterized crystallographically as pillared-layer three-nodal frameworks with one four-connected metal nodes and two crystallographically different four-connected ligand nodes. Their optical non-linearities are measured by the Z-Scan technique with an 8 ns pulsed laser at 532 nm. These two coordination polymers both exhibit strong NLO absorptive abilities [alpha(2) = (63 +/- 6) x 10 (12) mW (1) 1, ( 46 +/- 6) x 10 (11) mW (1) 2] and effective self-focusing performance [n(2) = (67 +/- 5) x 10 (18) 1, (13 +/- 3) x 10 (18) m(2) W (1) 2] in 1.02 x 10 (4) 1 and 1.05 x 10 (4) mol dm (3) 2 DMF solution separately. The values of the limiting threshold are also measured from the optical limiting experimental data. The heavy atom effect plays important role in the enhancement of optical non-linearities and optical limiting properties. (C) 2009 Elsevier B. V. All rights reserved.

电视精密跟踪控制系统的设计和应用

本文介绍了一个用于实际的电视精密跟踪控制系统,该控制系统在外场跟踪飞行体时稳定可靠,跟踪精度为数角秒.文中论述了人参与的复合捕获控制系统,找到了该系统参数的设计准则,即在切换时要满足相对变化量Δ≤15%.其次,重点论述了三阶无静差电视精密跟踪控制系统的设计方法,即利用 Z 变换直接求解,使得系统满足最佳条件旬(?)_(max)/(?)K_i=0和(?)_(max)/(?)K_f~2>0,从而,使得该控制系统满足了高稳定度和高精度的技术指标,并在实际中获得了应用.

层析静校正技术研究和应用

Static correction is one of the indispensable steps in the conventional onshore seismic data processing, particularly in the western part of China; it is theoretically and practically significant to resolve the issue of static correction. Conventional refraction static correction is put forward under the assumption that layered medium is horizontal and evenly distributed. The complicated nature of the near surface from western part of China is far from the assumption. Therefore, the essential way to resolve the static correction problem from the complex area is to develop a new theory. In this paper, a high-precision non-linear first arrival tomography is applied to solve the problem, it moved beyond the conventional refraction algorithm based on the layered medium and can be used to modeling the complex near surface. Some of the new and creative work done is as follows: One. In the process of first arrival tomographic image modeling, a fast high-order step algorithm is used to calculate the travel time for first arrival and ray path and various factors concerning the fast step ray tracing algorithm is analyzed. Then the second-order and third-order differential format is applied to the step algorithm which greatly increased the calculation precision of the ray tracing and there is no constraint to the velocity distribution from the complex areas. This method has very strong adaptability and it can meet the needs of great velocity variation from the complicated areas. Based on the numerical calculation, a fast high-order step is a fast, non-conditional and stable high-precision tomographic modeling algorithm. Two, in the tomographic inversion, due to the uneven fold coverage and insufficient information, the inversion result is unstable and less reliable. In the paper, wavelet transform is applied to the tomographic inversion which has achieved a good result. Based on the result of the inversion from the real data, wavelet tomographic inversion has increased the reliability and stability of the inversion. Three. Apply the constrained high-precision wavelet tomographic image to the static correction processing from the complex area. During tomographic imaging, by using uphole survey, refraction shooting or other weathering layer method, weathering layer can be identified before the image. Because the group interval for the shot first arrival is relatively big, there is a lack of precision for the near surface inversion. In this paper, an inversion method of the layer constraint and well constraint is put forward, which can be used to compensate the shallow velocity of the inversion for the shot first arrival and increase the precision of the tomographic inversion. Key words: Tomography ，Fast marching method，Wavelet transform, Static corrections, First break

东营凹陷下第三系岩性油气藏形成条件与预测

The Dongying depression, located in the northern part of the jiyang Sag in the Buohaiwan Basin, comprises one of the major oil-producing bases of the Shengli oil-field. The prediction and exploration of subtle or litho1ogical oil traps in the oil-field has become the major confronted target. This is also one of the frontier study areas in the highly-explored oil-bearing basins in East China and abroad. Based on the integrated analysis of the geological, seismic and logging data and the theories of sequence stratigraphy, tectono-stratigraphy and petroleum system, the paper has attempted to document the characteristics of the sequence stratigraphic and structural frameworks of the low Tertiary, the syndepositional faults and their control on deposition, and then to investigate the forming conditions and distribution of the tithological oil traps in the depression. The study has set up a set of analysis methods, which can be used to effectively analysis the sequence stratigraphy of inland basins and predict the distribution of sandstone reservoirs in the basins. The major achievements of the study are as follows: 1. The low Tertiary can be divided into 4 second-order sequences and 13 third-order sequences, and the systems tracts in the third-order sequences have been also identified based on the examination and correction of well logging data and seismic profiles. At the same time, the parasequences and their stacking pattern in the deltaic systems of the third member of the Shahejie Formation have been recognized in the key study area. It has been documented that the genetic relation of different order sequences to tectonic, climatic and sediment supply changes. The study suggested that the formation of the second-order sequences was related to multiple rifting, while the activity of the syndepositional faults controlled the stacking pattern of parasequences of the axial deltaic system in the depression. 2. A number of depositional facies have been recognized in the low Tertiary on the basis of seismic facies and well logging analysis. They include alluvial fan, fan delta or braided delta, axial delta, lowstand fan, lacustrine and gravity flow deposits. The lacustrine lowstand fan deposits are firstly recognized in the depression, and their facies architecture and distribution have been investigated. The study has shown that the lowstand fan deposits are the important sandstone reservoirs as lithological oil traps in the depression. 3. The mapping of depositional systems within sequences has revealed the time and special distrbution of depositional systems developed in the basin. It is pointed out that major elastic systems comprise the northern marginal depositional systems consisting of alluvial fan, fan delta and offshore lowstand fan deposits, the southern gentle slope elastic deposits composed of shallow lacustrine, braided delta and lowstand fan deposits and the axial deltaic systems including those from eastern and western ends of the depression. 4. The genetic relationship between the syndepositional faults and the distribution of sandstones has been studied in the paper, upper on the analysis of structural framework and syndepositional fault systems in the depression. The concept of structural slope-break has been firstly introduced into the study and the role of syndepositional faults controlling the development of sequence architecture and distribution of sandstones along the hinged and faulted margins have been widely investigated. It is suggested that structural styles of the structural slope-break controlled the distribution of lowstand fan deposits and formed a favorable zone for the formation of lithological or structure-lithological oil traps in the basin. 5. The paper has made a deep investigation into the forming condition and processes of the lithological traps in the depression, based the analysis of composition of reservoir, seal and resource rocks. It is pointed out that there were two major oil pool-forming periods, namely the end of the Dongying and Guangtao periods, and the later one is the most important. 6. The study has finally predicted a number of favorable targets for exploration of lithologieal traps in the depression. Most of them have been drilled and made great succeed with new discovered thousands tons of raw oil reserves.