White light emission from fiber pigtailed laser module

We fabricated a phosphor-conversion white light using an InGaN laser diode that emits 445 nm and phosphor that emit in the yellow. The InGaN laser diode was coupled to an optical fiber firstly and the phosphor was excited by the laser light output from the fiber. At 350 mA injection current the luminous flux and the luminous efficacy was 73 lm and 42.7 lm/W, respectively. The luminance was estimated to be 50 cd/mm(2). The relationship of the luminous flux and the luminous efficacy of the white light with injection current were measured and discussed.

Analysis on the high luminous flux white light from GaN-based laser diode

We fabricated a phosphor-conversion white light using an InGaN laser diode that emits 445 nm and phosphor that emits in the yellow region when excited by the blue laser light. At 500 mA injection current the luminous flux and the luminous efficacy were 113 lm and 44 lm/W, respectively. The relationship of the luminous flux and the luminous efficacy of the white light with an injection current were discussed. Based on the evaluation method for luminous efficacy of light sources established by the Commission International de I'Eclairage (CIE) and the phosphor used in this experiment, a theoretical analysis of the experiment results and the maximum luminous efficacy of this white light fabrication method were also presented.

Storage of photoexcited electron-hole pairs in an AlAs/GaAs heterostructure created by electron transfer in real and kappa spaces

The storage of photoexcited electron-hole pairs is experimentally carried out and theoretically realized by transferring electrons in both real and k spaces through resonant Gamma - X in an AlAs/GaAs heterostructure. This is proven by the peculiar capacitance jump and hysteresis in the measured capacitance-voltage curves. Our structure may be used as a photonic memory cell with a long storage time and a fast retrieval of photons as well.

Color filter-less technology of LED back light for LCD-TV - art. no. 68410G

Back Light Unit (BLU) and Color Filter are the two key components for the perfect color display of Liquid Crystal Display (LCD) device. LCD can not light actively itself, so a form of illumination, Back Light Unit is needed for its display. The color filter which consists of RGB primary colors, is used to generate three basic colors for LCD display. Traditional CCFL back light source has several disadvantages, while LED back light technology makes LCD obtain quite higher display quality than the CCFL back light. LCD device based on LED back light owns promoted efficiency of display. Moreover it can generate color gamut above 100% of the NTSC specification. Especially, we put forward an idea of Color Filter-Less technology that we design a film which is patterned of red and green emitting phosphors, then make it be excited by a blue light LED panel we fabricate, for its special emitting mechanism, this film can emit RGB basic color, therefore replace the color filter of LCD device. This frame typically benefits for lighting uniformity and provide pretty high light utilization ratio. Also simplifies back light structure thus cut down the expenses.

LCD-TV用直下式LED背光源的光学设计

三基色LED背光源是成就高品质液晶显示器的关键技术之一，其色域是传统CCFL背光源的150％以上。其中直下式背光源具有结构简单、光利用率高的特点，是目前大尺寸液晶显示背光源的首选，但是由于没有导光板，直下式背光源的光均匀性变得较差。通过对LED光场分布的模拟和分析，得出了一种新型LED光场分布设计，对由此光场分布的三基色LED组成的66cm（26in）背光源模拟表明，该背光源在未加扩散膜前，灯箱厚度为20～28mm时，亮度均匀度大于83％，△U’V’值在0．01左右；加上扩散膜之后，灯箱厚度为20mm时，均匀度可达到89．58％，△U’V’值达到0．0041。

Highly efficient white organic light-emitting devices based on a multiple-emissive-layer structure

Characteristics of white organic light-emitting devices based on phosphor sensitized fluorescence are improved by using a multiple-emissive-layer structure, in which a phosphorescent blue emissive layer is sandwiched between red and green&yellow ones. In this device, bis[(4,6-difluorophenyl)-pyridinato-N,C-2] (picolinato), bis(2,4-diphenyl-quinoline) iridium (III) acetylanetonate, fac bis (2-phenylpyridine) iridium, and 5,6,11,12-tetraphenylnaphthacene are used as blue, red, green, and yellow emitters, respectively.

White Electroluminescence from a Star-Like Polymer with an Orange Emissive Core and Four Blue Emissive Arms

A star-like white light-emitting polymer with an orange emissive core and four blue emissive arms is designed and synthesized. White electroluminescence is observed with simultaneous orange emission from the core and blue emission from the arms. A single-layer device based on this polymer emits white light with CIE coordinates of (0.35, 0.39) and a luminous efficiency of 7.06 cd A(-1).

Novel White Electroluminescent Single Polymer Derived from Fluorene and Quinacridone

A novel series of white light emitting single polymers are prepared by incorporating low contents of quinacridone into the main chain of polyfluorene. This is the first report of quinacridone-containing conjugated polymer. Single layer devices (ITO/PEDOT:PSS/polymer/Ca/Al) are fabricated with these polymers. Energy transfer from fluorene segments to quinacridone unit is observed. Moreover, in the EL process, quinacridone unit can trap electrons and cannot trap holes from fluorene segments.