Highly efficient photoluminescence of Er2SiO5 films grown by reactive magnetron sputtering method

E2SiO5 thin films were fabricated on Si substrate by reactive magnetron sputtering method with subsequent annealing treatment. The morphology properties of as-deposited films have been studied by scanning electron microscope. The fraction of erbium is estimated to be 23.5 at% based on Rutherford backscattering measurement in as-deposited Er-Si-O film. X-ray diffraction measurement revealed that Er2SiO5 crystalline structure was formed as sample treated at 1100 degrees C for 1 h in O-2 atmosphere. Through proper thermal treatment, the 1.53 mu m Er3+-related emission intensity can be enhanced by a factor of 50 with respect to the sample annealed at 800 degrees C. Analysis of pump-power dependence of Er3+ PL intensity indicated that the upconversion phenomenon could be neglected even under a high photon flux of 10(21) (photons/cm(2)/sec). Temperature-dependent photoluminescence (PL) of Er2SiO5 was studied and showed a weak thermal quenching factor of 2. Highly efficienct photoluminescence of Er2SiO5 films has been demonstrated with Er3+ concentration of 10(22)/cm(3), and it opens a promising way towards future Si-based light source for Si photonics. (C) 2009 Elsevier B.V. All rights reserved.

Mode Characteristics for Square Resonators With a Metal Confinement Layer

Microsquare resonators laterally confined by SiO2/Au/air multilayer structure are investigated by light ray method with reflection phase-shift of the multiple layers and two-dimensional (2-D) finite-difference time-domain (FDTD) technique. The reflectivity and phase shift of the mode light ray on the sides of the square resonator with the semiconductor/SiO2/Au/air multilayer structure are calculated for TE and TM modes by transfer matrix method. Based on the reflection phase shift and the reflectivity, the mode wavelength and factor are calculated by the resonant condition and the mirror loss, which are in agreement well with that obtained by the FDTD simulation. We find that the mode factor increases greatly with the increase of the SiO2 layer thickness, especially as d < 0.3 mu m. For the square resonator with side length 2 mu m and refractive index 3.2, anticrossing mode couplings are found for confined TE modes at wavelength about 1.6 mu m at d = 0.11 mu m, and confined TM modes at d = 0.71 mu m, respectively.

Single-mode condition for silicon rib waveguides with trapezoidal cross-section

Single-mode condition for silicon rib waveguides with trapezoidal cross-section was obtained using a numerical method based on imaginary-distance beam propagation method with non-uniform discretization. Both quasi-transverse-electric and quasi-transverse-magnetic modes were investigated. Simulated single-mode condition is given by a modified equation. Comparison with reported results shows that the Marcatili's method is in a better agreement with our results. (C) 2003 Elsevier B.V. All rights reserved.

1.55 mu m Ge islands resonant-cavity-enhanced narrowband detector

The high quality Ge islands material with 1.55 mu m photo-response grown on Sol substrate is reported. Due to the modulation of the cavity formed by the mirrors at the surface and the buried SiO2 interface, seven sharp and strong peaks with narrow linewidth are found. And a 1.55 mu m Ge islands resonant-cavity-enhanced (RCE) detector with narrowband was fabricated by a simple method. The bottom mirror was deposited in the hole formed by anisotropically etching, in a basic solution from the backside of the sample with the buried SiO2 layer in silicon-on-insulator substrate as the etch-stop layer. Reflectivity spectrum indicates that the mirror deposited in the hole has a reflectivity as high as 99% in the range of 1.2-1.65 mu m. The peak responsivity of the RCE detector at 1543.8 nm is 0.028 mA/W and a full width at half maximum of 5 nm is obtained. Compared with the conventional p-i-n photodetector, the responsivity of RCE detector has a nearly threefold enhancement.

Free radial oscillation of a sphere in relativistic elasticity theory

The spherically symmetric free radial oscillation in the first post-Newtonian approximation for a homogeneous and isotropic elastic sphere with a constant density is studied. Based on the Xu, Wu, and Soffel formalism, the relation of the oscillation frequency of the sphere with the radius, mass density, and elastic constants of the sphere is derived by using the successive approximation method.

Fluorescence Hydrogen Peroxide Probe Based on a Microstructured Polymer Optical Fiber Modified with a Titanium Dioxide Film

A highly sensitive microstructured polymer optical fiber (MPOF) probe for hydrogen peroxide was made by forming a rhodamine 6G-doped titanium dioxide film on the side walls of array holes in an MPOF. It was found that hydrogen peroxide only has a response to the MPOF probe in a certain concentration of potassium iodide in sulfuric acid solution. The calibration graph of fluorescence intensity versus hydrogen peroxide concentration is linear in the range of 1.6 x 10(-7) mol/L to 9.6 x 10(-5) mol/L. The method, with high sensitivity and a wide linear range, has been applied to the determination of trace amounts of hydrogen peroxide in a few real samples, such as rain water and contact lens disinfectant, with satisfactory results.

亚硝化—厌氧氨氧化处理猪场废水研究

猪场废水COD浓度高、氨氮浓度高、悬浮物浓度高，已成为农村面源污染的主要来源，并严重威胁到农村饮用水安全。猪场废水氨氮浓度高、处理难度大，如何采用经济高效的方法，去除氨氮使其达到排放标准，一直是猪场废水处理中面临的重要难题。 厌氧氨氧化是近年受到国内外水处理研究者广泛关注的新型生物脱氮技术，具有不需要外加有机碳源、节省供氧量、降低能耗等优点。虽然国内外研究者对厌氧氨氧化过程的脱氮机理、厌氧氨氧化菌的生理生化特性等进行了多方面的研究，但已有的报道大多以模拟废水为研究对象，以猪场废水为研究对象的报道，在国内外文献中极少有报导。 本论文以猪场废水为主要研究对象，考察了猪场废水的亚硝化过程、厌氧氨氧化的启动过程，并对亚硝化和厌氧氨氧化联合用于猪场废水脱氮进行了探索。 1．论文首先研究了猪场废水的亚硝化过程，考察了废水水质和主要运行条件对亚硝化过程的影响。实验表明：（1）亚硝化阶段反应时间为8到10h时，出水中氨氮和亚硝酸盐浓度比可达到1：1～1：1.23，满足厌氧氨氧化反应对二者比例的要求；达到前述要求时，氨氮去除率达到58.3～65.6 %，亚硝化率在整个过程均保持在97 %以上，COD去除率在59.2～68.6 %；（2）曝气量（溶解氧）对亚硝化过程影响显著，随着曝气量增大，达到厌氧氨氧化要求的氨氮与亚硝酸盐氮浓度比例所需水力停留时间τ越短，pH出现明显下降的时间越短；（3）τ对应的pH在7.8～8.1之间，无需进行pH调节即可满足厌氧氨氧化反应对pH的要求；（4）氨氮和COD降解过程遵循一级反应动力学，氨氮和COD降解的速率常数分别为0.0656～0.0724 1/h和0.0491～0.0664 1/h。 2．在进行亚硝化过程研究的同时，以模拟废水为试验对象，进行厌氧氨氧化启动研究。以反硝化污泥和养殖厂储水池厌氧底泥的混合污泥作为接种污泥，历时大约100天，培育出具有厌氧氨氧化活性的污泥，氨氮和亚硝酸盐氮最高进水浓度分别为223.8 mg/L和171.4 mg/L，去除率最高分别达48%和41.5%，此时二者消耗比例为1.33：1。 3．在猪场废水的亚硝化研究完成和厌氧氨氧化过程初步启动成功后，在模拟废水中逐步加入猪场废水的亚硝化处理出水，逐步实现亚硝化和厌氧氨氧化的组合。亚硝化出水添加到厌氧反应器后，厌氧氨氧化反应仍可继续进行，且去除效率逐步提高。研究发现添加的亚硝化出水中携带的亚硝化细菌在厌氧氨氧化菌膜外层生长并累积，增加了厌氧氨氧化反应基质的传质阻力，妨碍了厌氧氨氧化效率的提高。 4．亚硝化－厌氧氨氧化实际工程应用探索中，生物接触氧化池可在有效去除废水中的有机物的同时实现亚硝化，出水中氨氮和亚硝酸盐比例平均为1.10，可满足后续厌氧氨氧化的要求；在适宜的进水浓度和温度下，ABR池出现了厌氧氨氧化启动的迹象；研究同时发现，水质的波动和气温的变化是工程中影响厌氧氨氧化菌活性的重要因素。 论文的主要创新点在于：（1）以猪场废水为研究对象，以实现厌氧氨氧化为目标，对亚硝化过程进行了比较详细的考察，获得了亚硝化出水满足厌氧氨氧化要求的工艺条件，通过对其COD和氨氮降解过程的考察，得出亚硝化阶段COD降解和氨氮去除的动力学模型；（2）对亚硝化－厌氧氨氧化处理猪场废水进行了探索，确立了影响其污染物去除率稳定的重要因素。 论文的上述研究成果，为厌氧氨氧化技术的实用性研究提供理论依据。 Piggery wastewater, which is characterized by high concentration of COD、ammonium and suspend substance, has become a most important source of non-point source pollution and also severely threats drinking water security in rural area. How to discharge piggery wastewater with the ammonium concentration meeting standard by economical and effective method? This is the most urgent problem in piggery wastewater treatment. As a new biological nitrogen removal technology, Anammox process has been paid more and more attention by researchers all over the world. Anammox has advantages of no need of organic carbon addition, low oxygen consumption and energy consumption. Plenty of investigations have been carried out to the mechanism, physiological and biochemical characteristic of bacteria about Anammox. Most of researches focused on synthetic wastewater, there is rare report about its application in piggery wastewater. In this paper，experimental studies were performed to investigate Sharon process in treatment of piggery wastewater，the start up process of Annammox using synthetic wastewater were studied, the feasibility of applying Sharon-Anammox process in the nitrogen removal of piggery wastewater was evaluated. 1. Sharon process of piggery wastewater was firstly investigated to analyze the effects of water quality and main running parameters, which meet the NH4+-N to NO2--N ratio requirement of successive Anammox. Results showed: (1)During Sharon Process，after 8～10 hours’ reaction the NH4+-N to NO2--N ratio in effluent reached 1:1.0～1:1.23, when the removal percentage of NH4+-N was 58.3～65.6 %, a semi-nitration rate of above 97 % was achieved during the process; meanwhile 59.2～68.6 % of the COD was also removed. (2)The aeration rate（oxygen） had obvious effect on the hydraulic retention time(τ) which met the NH4+-N to NO2--N ratio requirement of Anammox. As aeration rate increased, the hydraulic retention time(τ) was shortened. (3) The pH corresponding to τ was between 7.8 and 8.1, thus it needed no artificial adjustment. (4) The reduction of ammonia and COD followed the first-order reaction kinetics. The velocity constants of ammonia and COD were 0.0656～0.0724 1/h and 0.0491～0.0664 1/h, respectively. 2. The startup of Anammox process using the artificial wastewater was performed simultaneously with Sharon. The aim was to investigate the running parameters of Anammox and make foundation for the combination stage. By using the mixture of denitrifying sludge and anaerobic sludge in tank of the breeding factory, sludge of Anammox activity was cultivated in UASB after 100 days. The removal percentage of NH4+-N and NO2-N were up to 48% and 41.5%, respectively, when the NH4+-N and NO2-N influent concentration were 223.8 mg/L and 171.4 mg/L, respectively, the NH4+-N and NO2-N removal rate was 1.33:1. 3. After investigation of Sharon and startup of Anammox, effluent of Sharon process was added into the synthetic wastewater to combine Sharon and Anammox step by step. It took some time after the addition of Sharon effluent that Anammox reaction continued and the removal rate kept increasing. It indicated that nitrifying bacteria were carried by the Sharon effluent cumulated in the outer layer of Anammox. This enhanced transfer resistance of Anammox reaction and the increasing removal rate was restrained. 4. In the bio-contact oxidation pond of practical project, Sharon process were carried out successfully and organic compounds were removed effectively. An average NO2-N/ NH4+-N rate of 1:1.0 was achieved in the effluent, which met the requirement of successive Anammox. Under condition of suitable influent concentration and temperature, there was evidence that Anammox could start up in ABR. The variety of wastewater and temperature had great affects on Anammox activity in practical engineering. Innovation of this paper: (1) The Sharon process for treating piggery wastewater was discussed in details. Technological parameters that met requirement of Anammox were obtained. The dynamic models of COD and ammonium removal in the process were educed. (2) Sharon-Ananmmox for treatment of piggery wastewater was investigated, and the primary influencing factors was studied. This paper could be a theoretical consult for research of Anammox utility.

An efficient in vitro method for mass propagation of Potentilla potaninii wolf

This study reports a method for high-frequency shoot organogenesis and plant establishment of Potentilla potaninii Wolf. Hypocotyl and cotyledon explants of P. potaninii were cultured on Murashige and Skoog (MS) medium supplemented with various concentrations of benzyladenine (BA) and alpha-naphthaleneacetic acid (NAA) to induce adventitious shoot formation for micropropagation. The highest frequency of adventitious shoot regeneration was achieved from hypocotyl and cotyledon explants grown on MS medium supplemented with 5.0 mg l(-1) BA and 1.0 mg l(-1) NAA. The regenerated shoots rooted most efficiently on half-strength MS medium supplemented with 1.0 mg l(-1) NAA and 0.5 mg l(-1) indole-3-acetic acid or indole-3-butyric acid. The acclimatized plants with normal morphology and growth characters flowered and set seeds in the following year.

Detection of K-ras exon 1 mutations by constant denaturant capillary electrophoresis

Among various mutation detection methods, constant denaturant capillary electrophoresis (CDCE) is one of the most common techniques for rapid identification of known or unknown mutations. In this report, a CDCE analysis method with homemade linear polyacrylamide (LPA) kit was developed on ABI 310 genetic analyzer, the effect and relationship of various denaturing factors in CDCE analysis were investigated and K-ras gene mutations of 31 coloerctal cancer patients were detected. Results indicate that, with the increase of chemical danaturant concentration, the optimum temperature was lowered, and when the concentration of urea (formamide) was higher than 7 M (40%), the homoduplex and heteroduplex of mutant samples were separated with difficulty. Detection results of K-ras gene in colorectal samples indicated that mutations were present in eight (26%) of 31 patients; most mutations were localized in codon 12, which is thought to be a critical step and plays an important role in human colorectal carcinogenesisas. Copyright (C) 2004 John Wiley Sons, Ltd.

Determination of 1-phenyl-3-methyl-5-pyrazolone-labeled carbohydrates by liquid chromatography and micellar electrokinetic chromatography

In this paper, the method for the derivatization of carbohydrates with 1-phenyl-3-methyl-5-pyrazolone (PMP) was simplified. One-third of the derivatization time was saved. Five monosaccharide derivatives have been well separated by MEKC and HPLC under optimized conditions. Good reproducibility could be obtained with relative standard deviation (RSD) values of the migration times within 5.0 and 2.3%, respectively. Furthermore, the developed methods have been successfully applied to the analysis of carbohydrates in Aloe powder and food. These methods are quite useful for routine analysis of monosaccharides and oligosaccharides in real samples. (C) 2003 Elsevier B.V. All rights reserved.

A Relay Level Set Method for Automatic Image Segmentation

This paper presents a new image segmentation method that applies an edge-based level set method in a relay fashion. The proposed method segments an image in a series of nested subregions that are automatically created by shrinking the stabilized curves in their previous subregions. The final result is obtained by combining all boundaries detected in these subregions. The proposed method has the following three advantages: 1) It can be automatically executed without human-computer interactions; 2) it applies the edge-based level set method with relay fashion to detect all boundaries; and 3) it automatically obtains a full segmentation without specifying the number of relays in advance. The comparison experiments illustrate that the proposed method performs better than the representative level set methods, and it can obtain similar or better results compared with other popular segmentation algorithms.

STUDY OF COARSENING OF MICRODOMAINS IN BLOCK COPOLYMERS BY LATTICE BOLTZMANN METHODS

In order to understand the coarsening of microdomains in symmetric diblock copolymers at the late stage, a model for block copolymers is proposed. By incorporating the self consistent field theory with the free energy approach Lattice Boltzmann model, hydrodynamic interactions can be considered. Compared with models based on Ginzburg-Landau free energy, this model does not employ phenomenological free energies to describe systems. The model is verified by comparing the simulation results obtained using this method with those of a dynamical version of the self consistent mean field theory. After that,the growth exponents of the characteristic domain size for symmetric block copolymers at late stage are studied. It is found that the viscosity of the system affects the growth exponents greatly, although the growth exponents are all less than 1/3 Furthermore, the relations between the growth exponent, the interaction parameter and the chain length are studied.

Combining chemical reduction with an electrochemical technique for the simultaneous detection of Cr(VI), Pb(II) and Cd(II)

This work herein reports the approach for the simultaneous determination of heavy metal ions including cadmium (Cd(II)), lead (Pb(II)), and chromium (Cr(VI)) using a bismuth film electrode (BFE) by anodic stripping voltammertry (ASV). The BFE used was plated in situ. Due to the reduction of Cr(VI) with H2O2 in the acid medium, on one hand, the Cr(III) was produced and Cr(VI) was indirectly detected by monitoring the content of Cr(III) using square-wave ASV. On the other hand, Pb(II) was also released from the complex between Pb(II) and Cr(VI). Furthermore, the coexistence of the Cd(II) was also simultaneously detected with Pb(II) and Cr(VI) in this system as a result of the formation of an alloy with Bi. The detection limits of this method were 1.39 ppb for Cd(II), 2.47 ppb for Pb(II) and 5.27 ppb for Cr(VI) with a preconcentration time of 120 s under optimal conditions (S/N = 3), respectively. Furthermore, the sensitivity of this method can be improved by controlling the deposition time or by using a cation-exchange polymer (such as Nafion) modified electrode.

Crystal structures of EtEDTB center dot 1.4C(2)H(5)OH center dot 5H(2)O and H4EtEDTB(ClO4)(4)center dot C2H5OH (EtEDTB=N, N, N ', N '-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine)

The crystal structures of EtEDTB.1.4C(2)H(5)OH.5H(2)O 1 and H4EtEDTB(ClO4)(4).C2H5OH 2 (EtEDTB = N, N,N',N'-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine) have been determined by single-crystal X-ray diffraction method. Compound 1 crystallizes in the space group P(1) over bar with a = 11.489(2), b = 11.866(3), c = 12.002(3) Angstrom, alpha = 97.47(2), beta = 114.564(13), gamma = 114.11(2)degrees, V = 1266.6(5) Angstrom(3), Z = 1, M-r = 847.48, D-c = 1.111 g/cm(3), F(000) = 456 and mu(MoKalpha) = 0.076 mm(-1). A total of 5207 reflections were measured for 1, of which 4323 were independent. The structure of 1 was solved by direct methods and refined by full-matrix least-squares technique to the final R = 0.0706 and wR = 0.1802 for 1318 observed reflections with I > 2sigma(I). In the structure of 1, centrosymmetric EtEDTB molecules are linked by hydrogen bonds through water and ethanol to form 2-dimensional network. Compound 2 crystallizes in the space group C2/c with a = 24.260(5), b = 13.040(3), c = 17.680(4) Angstrom, beta = 97.50(3)degrees, V = 5545.2(2) Angstrom(3), Z = 4, M-r = 1140.80, D-c = 1.366 g/cm(3), F(000) = 2384 and mu(MoKalpha) = 0.289 mm(-1).

Syntheses, structures and luminescence of silver(I) sulfonate complexes with PPh3 ligand

In this paper, four new luminescent silver(I) sulfonate complexes with PPh3, namely Ag(L1)(PPh3)(2) (1), Ag(L2)(PPh3)(3) (2), [Ag-2(L3)(PPh3)(4) (H2O)center dot 1.5CH(3)CN center dot 0.5H(2)O (3) and [Ag-4(L4)(PPh3)(10)]center dot 8H(2)O (4), where L1=p-toluenesulfonate, L2=1-naphthalenesulfonate, L3=3-carboxylate-4-hydroxybenzenesulfonate, L4=1, 3, 6, 8-pyrenetetrasulfonatc and PPh3=triphenylphosphine, have been synthesized and characterized. The crystal structures were determined by single-crystal X-ray diffraction method. Compounds 1, 2, 3 and 4 adopt discrete structures rather than polymeric structures. Compounds I and 2 show mononuclear structures while 3 and 4 are dinuclear and tetranuclear molecules, respectively. Moreover the numbers of PPh3 molecules coordinating to one silver center are two or three. The photoluminescent properties of 1, 2 and 3 are discussed.