Toughening of poly(butylene terephthalate) with epoxidized ethylene propylene diene rubber

In this paper, unepoxidized ethylene propylene diene rubber (uEPDM) was first epoxidized with formic acid and H2O2, and then the epoxidized ethylene propylene diene rubber (eEPDM) was melt-mixed with PET resin in a Brabender-like apparatus. Toughening of PET matrix was achieved by this method. The dispersion of rubber particles and phase structure of the blends were also observed by SEM. It has been suggested that the epoxy groups in the eEPDM could react with PET end groups to form a graft copolymer which could act as an interfacial compatibilizer between the PBT matrix and eEPDM rubber dispersed phase. This is beneficial to the improvement of the impact performance of PBT. (C) 1997 Elsevier Science Ltd.

Toughened poly(butylene terephthalate) by epoxided ethylene-propylene-diene-rubber

Blends of poly (butylene terephthalate) (PBT) and epoxided ethylene-propylene-diene terpolymer (EEPDM) were prepared. Their mechanical properties and morphology were studied by Izod impact test machine and scanning electronic microscope respectively, It was found that the notched Izod impact strength of blend PBT/EEPDM was as about 23 times as that of pure PET and about 10 times as that of blend PBT/EPDM at room temperature, The dispersed rubber particles were much smaller and the phase boundary was more blurred in blend PBT/EEPDM than in blend PBT/EPDM. The toughness of blend PBT/EEPDM was much more better than that of blend PET and PBT/EPDM, which was in good agreement with the difference between their morphologies.

RADIATION VULCANIZATION OF HYDROGENATED ACRYLONITRILE-BUTADIENE RUBBER (HNBR)

Raw polymer and compound of hydrogenated acrylonitrile butadiene rubber (HNBR) were subjected to gamma-ray irradiation. Crosslinking was found to be the main chemical reaction induced by irradiation; the ratio of chain scission to crosslinking as well as

EFFECT OF REPTATION ON FRACTURE-MECHANICS OF RUBBER NETWORKS

End-linked hydroxyl-terminated polybutadiene containing unattached linear polybutadiene was used to study the effect of reptating species on the fracture mechanics of rubber networks. The concentration of reptating species in the networks ranged from 0 to 100%. The fracture mechanics of the networks was described using the critical strain energy release rate in mode III testing, i.e. the tearing energy. The tearing energy was measured at room temperature using a 'trouser' specimen at a strain rate spanning five logarithmic decades. When the strain rate was as low as 10(-4) s-1, the tearing energy of the networks increased with reduction in reptating species. In this case the reptating species did not contribute to the tearing energy of the networks due to relaxation. Hence, the tearing energy increased with the number of crosslinked chains per unit volume in the networks. At a strain rate ranging from 10(-3) to 10(-1) s-1, the tearing energy of the networks was governed by local viscosity. The tearing energies of the networks containing various amounts of reptating species were superimposed to give a master curve based on the Williams-Landel-Ferry equation.

Preparation of a novel polysulfone/polyethylene oxide/silicone rubber multilayer composite membrane for hydrogen-nitrogen separation

A novel poly sulfone/polyethylene oxide/silicone rubber (PSOPEO/SR) multilayer composite membrane was fabricated by double coating polysulfone substrate membrane with polyethylene oxide and silicone rubber. Gas permeation experiments were performed at 30 degrees C for hydrogen and nitrogen. PSf(PEO/SR membrane displayed high and steady performance for H-2/N-2: permeances of H-2 and N-2 of 49.51 and 0.601 GPU, respectively, and H-2/N-2 ideal separation factor of 82.3. It was explained that layer interfaces due to the introduction of PEO layer act as the permselective media and are responsible for the higher H-2/N-2 ideal separation factor which has exceeded the intrinsic permselectivities of the three polymers used in this study. (c) 2005 Elsevier B.V. All rights reserved.

Comparison-speed liquid jets

The performance of a small high-speed liquid jet apparatus is described. Water jets with velocities from 200 to 700 m/s were obtained by firing a deformable lead slug from an air rifle into a stainless steel nozzle containing water sealed with a rubber diaphragm. Nozzle devices using the impact extrusion (IE) and cumulation (CU) methods were designed to generate the jets. The effect of the nozzle diameter and the downstream distance on the jet velocity is examined. The injection sequences are visualized using both shadowgraphy and schlieren photography. The difference between the IE and CU methods of jet generation is found.

Performance of a small high-speed liquid jet apparatus

The performance of a small high-speed liquid jet apparatus is described. Water jets of 200m/s to 700m/s have been obtained by firing a deformable lead slug from an air rifle into a stainless steel nozzle containing water sealed with a rubber diaphragm. Nozzle devices of using the impact extrusion (IE) method and cumulation (CU) method are designed to generate jets. The injection sequences are visualized using schlieren photography. The difference between the IE and CU methods in the jet generation is found.

Deformation Of Pdms Membrane And Microcantilever By A Water Droplet: Comparison Between Mooney-Rivlin And Linear Elastic Constitutive Models

In this paper, we studied the role of vertical component Of Surface tension of a water droplet on the deformation of membranes and microcantilevers (MCLs) widely used in lab-on-a-chip and micro-and nano-electromechanical system (MEMS/NEMS). Firstly, a membrane made of a rubber-like material, poly(dimethylsiloxane) (PDMS), was considered. The deformation was investigated using the Mooney-Rivlin (MR) model and the linear elastic constitutive relation, respectively. By comparison between the numerical solutions with two different models, we found that the simple linear elastic model is accurate enough to describe such kind of problem, which would be quite convenient for engineering applications. Furthermore, based on small-deflection beam theory, the effect of a liquid droplet on the deflection of a MCL was also studied. The free-end deflection of the MCL was investigated by considering different cases like a cylindrical droplet, a spherical droplet centered on the MCL and a spherical droplet arbitrarily positioned on the MCL. Numerical simulations demonstrated that the deflection might not be neglected, and showed good agreement with our theoretical analyses. (C) 2008 Elsevier Inc. All rights reserved.

北京东灵山地区暖温带森林生态系统能量环境和能量固定的研究

水文研究了北京东灵山地区落叶阔叶林和人工油松林的能量环境和能量固定，以及相关的生态学过程。重点研究了落叶阔叶林林冠表面、灌木层表面和草本层表面的总辐射、直射辐射、散射辐射、反射辐射、净辐射和长波将辐射、分光谱辐射，强调了自然条件下斜坡对上述辐射分量的影响。上述分量随森林内层次的下降而剧减，光谱组成也发生变化，长波辐射和短波红外辐射所受的影响较小。天气对辐射通量的日进程和月际变化都有重大影响。 落叶阔叶林主要树种叶片净光合速率在7月底8月初达到最大值，以辽东栎的最高，五角枫最低。除大叶白蜡外，正午或稍后有明显的午休现象。油松小技的光合速率上层）中层）下层，7月底和8月全月都是光合速率高峰期。白天净光合速率在中午没有明显的“午休”现象 自然环境下油松不同年龄的针叶的光合速率与光强度的关系近似于一种抛物线关系，而不是人工控制条件下测定所出现的双曲线关系。 主要落叶阔叶乔灌木和油松树干的呼吸速率7月份最高，10月最低，24小时连续测定结果表明，乔木树种树干呼吸在下午或傍晚达到最大值，是因为树干温度落后于空气温度的变化节奏造成的。 以油松为例，研究了树木侧枝长的年增长规律，发现侧枝年增长量随着年份发生有规律的变化，与气候因子的关联分析与回归分析表明，枝长的年增长量与空气温度、年降水量和年蒸发量关系最为密切。最后利用光合生产潜力逐步修正的途径和Lieth-Box途径，估算了被研究森林的潜在生产力，并分析了造成估计值偏高或偏低的原因。

岷江中上游植被生态恢复过程中若干问题的探讨

　1．对四川省岷江上游地区（茂县）的锐齿槲栎（Quercus aliena var. acuteserrata）天然次生林进行研究，发现：(1) 坚果完好比例约在14% ~26%之间，完好坚果的发芽率和发芽势都比较高，但在天然状况下能够留存到翌年5月的坚果几乎没有。因此，实生幼苗的天然补充就受到了严重的限制。(2) 林缘的幼苗密度低于所有其它生境的 (P<0.05)，林中的幼苗密度最高，和林窗的比较有显著差异(P<0.05), 而和灌丛的比较则差异不显著（P>0.05）。在灌丛幼苗密度和林中以及林窗的比较都没有差异。动物对坚果的取食速度则是林中的最慢 (10.0%)，林窗和林缘的基本相同(分别为61.1%和66.5%)，取食速度都明显快于林中(P<0.01)。(3) 林中的幼苗在小于100 cm的各高度内都有大量分布，说明在林中树冠下幼苗是可以长期存在的，暗示在幼苗阶段的锐齿槲栎可能是耐荫的。(4) 在林中缺失幼树，在林缘则有包括幼树在内的完整的更新大小系列，表明林缘是更新的关键地点。(5) 在栎林的每一个大小级别上，萌生个体和实生个体都按各种比例伴生，说明导致萌生的干扰一直在发生，并可能在森林的更新中扮演重要角色;也说明该地区的锐齿槲栎林由萌生和实生起源的个体混合组成。 2．栎林是北半球温带森林的重要组成部分，因此栎林更新是全球森林更新研究的热点之一，而啮齿动物对栎林更新的影响则是关注的焦点。在2002~2003年，通过坚果标记研究了未被取食和遗弃坚果（即咬开后只有少部分被捕食后丢弃在林中的坚果）的健康比例，并定量测定了坚果的捕食、搬运、遗弃、丢弃、贮藏和留存等各种命运的比例和特点;对坚果也进行了各种人为的处理，以观测其命运和动物取食速度，发现：(1) 遗弃坚果中不健康坚果的比例比动物未取食的天然坚果中的比例有极显著的增加 (P>0.05)，暗示啮齿动物一般是通过咬开坚果来识别坚果健康与否并决定是否捕食。(2) 根据坚果命运和对照相比改变与否以及如何改变，各种人工处理坚果的命运可以分为 4 类：① 坚果命运没有任何显著改变;② 坚果被就地捕食的速度降低，搬运的速度不变，最终搬运坚果的比例增加而就地捕食坚果的比例降低，留存坚果的比例偶尔能增加至0.2%;③ 坚果就地捕食的速度几乎降至0，搬运的速度则在下降一段时间后又上升，并且搬运作用持续了相对长的时间，最终搬运坚果的比例大大增加，就地捕食坚果的比例很低，留存率为0;④ 坚果被搬运和就地捕食的速度和比例都降低，留存坚果的比例相应的大大增加，甚至可以达到50%。(3) 命运得到显著改变的②、③、④类坚果所承受的人工处理按照作用方式又可以分为主要作用于坚果化学状态（即气味浓度）的处理、主要作用于坚果物理状态（颜色、形态、有无附属物等）的处理以及使坚果处于不同颜色背景的处理;其中主要作用于坚果化学状态的处理对坚果命运具有最重大的改变，如胶带包裹处理和烧焦处理;其它各种主要作用于坚果的物理状态和所处背景的处理对其命运则也具有相对轻微的改变。这一试验结果可能证明：啮齿动物在对坚果进行识别和取食选择等活动时主要依赖于嗅觉来感知坚果的可食性，但是能感觉物理状态和所处背景的视觉也起一定程度的作用。(4) 啮齿动物对栎树坚果进行就地捕食、遗弃、搬运、异地捕食、丢弃、贮藏等作用，使各种命运的坚果都具有一定的数量比例和特点，也提供了动物影响栎林更新的多种可能途径。 3．人工干扰是任何退化生态系统中都始终存在的重大问题。除了明显的砍伐或者采摘外，人工践踏也是一种重要的干扰，特别是在茂县的山林普遍被牛马不断的放牧的情况下，这个干扰的后果就更加显著。为此研究了人脚踩踏的路上的白车轴草和未踩踏草坪上白车轴草在最大叶长、株高、芽高、构件数量、构件平均鲜重、死叶数量、根长等构型指标，根、茎、叶三者的生物量（干重）及比例等生物量指标，平均花序数量、花平均数量等繁殖指标方面的不同，发现踩踏使白车轴草植株：(1) 株高降低，芽高降低，最大叶长变小，平均每厘米的构件数量增加，构件平均鲜重降低，根长度减小，死叶数量增加。(2) 平均花序数量下降，每花序的花平均数量下降。(3) 但是在生物量的分配上，根和茎的生物量没有显著的下降，但是叶的生物量显著减低。因为白车轴草的茎可以不断克隆繁殖，所以踩踏对其存活可能没有太大的影响，只是造成了植株的矮化和密集化，根也变短;但是对种子繁殖有重大影响，反映在平均花序数量和每花序平均花数的显著下降上。在生物量的分配中，作为主要的同化器官，叶的生物量显著下降，而根茎比没有变化。这可能说明这样的克隆植物其物质流动是呈现网络化的特征，具有比较强的抗干扰能力。 4．连香树、油松、日本落叶松、华山松油松混合林是茂县地区的几种主要的已经营造的林型或者树种。为了了解其20年来的营林效果，运用样方调查的方法测量了这几种树种或者林型的胸径、持水量、凋落物现存量、密度等，评价了它们在生长、营业循环和水土保持等方面的差异。结果表明：日本落叶松具有生长缓慢，凋落物现存量大，涵养水分能力良好的树种，值得推广;油松生长迅速，凋落物现存量巨大，涵养水分能力一般的树种，也可以大力栽植;油松和华山松的混交林具有比较大的蓄积量和较好的涵养水分的能力，可以推广;而连香树则做为生长速度中等，成材率低，凋落物现存量小，涵养水分能力差的树种，不应该进一步推广。

Fiber Bragg grating hydrophone with high sensitivity

A fiber Bragg grating (FBG) hydrophone with high sensitivity was demonstrated. This hydrophone used a rubber diaphragm and a copper hard core as the sensing element. To compensate the hydrostatic pressure, a capillary tube was fixed at the end of the hydrophone. Theoretical analysis of the acoustic pressure sensitivity was given in this letter. Experiments were carried out to test the frequency response of the hydrophone. The result shows that when the Young's modulus of the diaphragm is higher, a flatter frequency response will be obtained.

Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed tinder vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na2CO3, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 degrees C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) similar to 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt% which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na2CO3 addition. Pyrolysis gas was mainly composed of H-2, CO, CH4, CO2, C2H4 and C2H6. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.