光通过纳米颗粒随机散射体透射光强的计算及分析

光通过随机散射体后透射光强的估算,对于提取散射体内部无法直接测量或者无法直接观察的信息至关重要。在分析平行光束通过纳米圆形颗粒随机散射体出射面上光强组成的基础上推导了透射光强的计算公式,并指出多重散射理论、一阶多重散射理论和朗伯比尔定律在一定近似程度上可以相对精确地估算透射光强。这三种方法的估算结果之间会出现四种相对关系。根据这些相对关系,分析了光在散射体内部传输时散射过程的特征以及各种散射过程对出射面光强的贡献大小。

静动结合的化学腐蚀法制备近场光学探针的理论分析

理论上分析了静动结合的化学腐蚀法制备探针的具体机理及过程。在静态腐蚀的过程中, 利用流体力学Young-Laplace方程的一级近似解获得了光纤插入到HF酸中形成的新月形高度。在动态腐蚀过程中, 详细分析了当静态腐蚀时间和动态腐蚀时间分别取不同值时, 光纤移动速度对光纤探针结构的影响。利用此法可制备出尖端锐利、大锥角或多锥体等各种结构的光纤探针。这为实验上制备出性能优良的探针, 为拓宽扫描近场光学显微镜的应用范围奠定基础。将上述理论分析的结果与本文实验中所得初步结果进行了比较, 所得结果一致。

Broadband near-infrared emission in Er3+-Tm3+ codoped chalcohalide glasses

The near-IR emission spectra of Er3+-Tm3+ codoped 70GeS(2)-20In(2)S(3)-10CsI chalcohalide glasses were studied with an 808 nm laser as an excitation source. A broad emission extending from 1.35 to 1.7 mu m with a FWHM of similar to 160 nm was recorded in a 0.1 mol.% Er2S3, 0.5 mol.% Tm2S3 codoped chalcohalide glass. The fluorescence decay curves of glasses were measured by monitoring the emissions of Tm3+ at 1460 nm and Er3+ at 1540 nm, and the lifetimes were obtained from the first-order exponential fit. The luminescence mechanism and the possible energy-transfer processes are discussed with respect to the energy-level diagram of Er3+ and Tm3+ ions. (C) 2008 Optical Society of America

Design of high-efficiency diffraction gratings based on rigorous coupled-wave analysis for 800nm wavelength

We report on the design of a high diffraction efficiency multi-layer dielectric grating with wide incident angle and broad bandwidth for 800 nm. The optimized grating can achieve > 95% diffraction efficiency in the first order at an incident angle of 5 degrees from Littrow and a wavelength from 770nm to 830 nm, with peak diffraction efficiency of > 99.5% at 800 nm. The electric field distribution of the optimized multi-layer dielectric grating within the gratings ridge is 1.3 times enhancement of the incidence light, which presents potential high laser resistance ability. Because of its high-efficiency, wide incident, broad bandwidth and potential high resistance ability, the multi-layer dielectric grating should have practical application in Ti:sapphire laser systems.

氮素添加对内蒙古羊草草原净氮矿化的影响

　　氮素作为陆地生态系统生产力主要的限制因子，对生态系统过程的调控有着重要的意义。净氮矿化是有机氮素到无机氮素的转变过程，该过程决定了土壤氮素的可利用性。准确估计土壤的供氮能力可以为确定最佳施肥量和施肥时间提供理论依据，并将影响着土地的可持续发展和管理政策。氮矿化潜力N0被定义为在最适温度和湿度下，土壤氮素在无限时间内所能矿化的最大量。由于氮矿化潜力是土壤供氮能力很好的指示值，所以对氮矿化潜力的研究能够使我们更好地了解土壤的氮素矿化动态和其供氮潜力。 　　为更好地了解天然草原氮素矿化对全球氮沉降背景以及草原施肥管理模式的响应，我们从2000年起在内蒙古羊草草原开展了长期的氮素添加实验，分别设置对照(N0)、添加5g N•m-2(N1.75)、30g N•m-2(N10.5)和80g N•m-2(N28)四个氮肥添加梯度以及对照(control)、添加100g有机肥•m-2(O100)、添加500g有机肥•m-2(O500)、添加1000g有机肥•m-2(O1000)四个有机肥添加梯度。氮肥添加在相邻并同时进行施肥的两个生态系统类型中展开，即成熟羊草草原（A区，1979年围封）和退化的羊草草原（B区，1999年围封），有机肥添加也同时在与之相邻的C区中展开（C区的土地利用历史与B区一致）。 2002年和2006年，从A、B区中进行氮肥处理后的土壤取样；有机肥处理的土壤样品从2002年C区中获得。土样在最佳温度(25℃)和湿度(60%田间持水量（WHC）)下进行了5周室内培养，并用阶段淋溶方法来测定氮肥添加和有机肥添加对土壤氮矿化动态的影响。 　　氮肥添加显著降低了土壤的pH值，但累积氮矿化量与土壤pH值、有机碳、全氮均没有显著的相关性。在两个区内，氮素添加都显著改变了土壤的累积氮矿化量。最高氮素处理N28相对应于最低的累积氮矿化量，而低氮素处理N1.75却使得累积氮矿化量最高。同时，在N0和N1.75处理中硝态氮的含量高于铵态氮，但在N28处理中却表现出相反趋势。实验还表明大多数氮素添加强度处理在A区比B区有更高的土壤累积氮矿化量。 　　有机肥添加也显著改变了土壤5周内的累积氮矿化量，并且累积氮矿化量随有机肥添加强度的升高而显著增加。培养5周末时土壤的累积铵态氮的含量与有机肥施加强度之间并没有相关性，但是累积硝态氮的含量有随着有机肥施加强度的上升而增加的趋势。 　　基于前5周土壤培养所得到的结果，我们选择了氮肥添加的N0，N1.75， N28处理以及有机肥添加的control、O100、O1000处理继续进行了长达15周的培养。培养数据与描述土壤氮矿化动态的一级动力学模型--first-order kinetics: Nm=N0（1－exp(-kt)）拟合良好( R2=0.893～0.97)。无论是氮肥添加还是有机肥添加都显著增加了土壤的氮矿化潜力N0，并且N0随着氮肥或者机肥添加强度的增加而增加。对于氮肥处理的土壤来说， N0与氮矿化速率常数k之间反向相关，但是在有机氮处理的土壤中N0与k之间却没有相关性。总的结果显示，经有机肥添加的土壤比经氮肥添加的土样有着更大的氮矿化潜力N0值以及氮矿化速率常数k值，较大的k值暗示着土壤氮素较快的周转速率。

Kinetic study of the 2-methyl-3-methoxy-4-phenylbutanoic acid produced by oxidation of microcystin in aqueous solutions

Microcystins (MCs) are a family of related cyclic hepatotoxic heptapeptides, of which more than 70 types have been identified. The chemically unique nature of the C20 beta-amino acid, (2S, 3S, 8S, 9S)-3-amino-9-methoxy-2,6,8-trimethyl-10-phenyldeca4,6-dienoic acid (Adda), portion of the MCs has been exploited to develop a strategy to analyze the entirety. Oxidation of MCs causes the cleavage of MC Adda to form 2-methyl-3-methoxy-4-phenylbutanoic acid (MMPB). In the present study, we investigated the kinetics of MMPB produced by oxidation of the most-often-studied MC variant, MC-LR (L = leucine, R = arginine), with permanganate-periodate. This investigation allowed insight regarding the influence of the reaction conditions (concentration of the reactants, temperature, and pH) on the conversion rate. The results indicated that the reaction was second order overall and first order with respect to both permanganate and MC-LR. The second-order rate constant ranged from 0.66 to 1.35 M/s at temperatures from 10 to 30 degrees C, and the activation energy was 24.44 kJ/mol. The rates of MMPB production can be accelerated through increasing reaction temperature and oxidant concentration, and sufficient periodate is necessary for the formation of MMPB. The initial reaction rate under alkaline and neutral conditions is higher than that under acidic conditions, but the former decreases faster than the latter except under weakly acidic conditions. These results provided new insight concerning selection of the permanganate-periodate concentration, pH, and temperature needed for the oxidation of MCs with a high and stable yield of MMPB.

Studies on the adsorption equilibrium and kinetics of pentachlorophenol on suspended particulate matter of Donghu Lake water

In this paper, the adsorption equilibrium and kinetic behaviors of pentachlorophenol (PCP) on suspended particulate matter (SPM) in Donghu Lake water were investigated. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and their constants were evaluated. The results indicated that the adsorption of PCP on Donghu Lake SPM followed the Freundlich isotherm. Furthermore, the first order Lagergren rate equation and the pseudo-second order rate equation were used to describe the kinetic behaviors of PCP adsorption on Donghu Lake SPM, the rate constants were determined, and the kinetic process of the adsorption of PCP on Donghu Lake SPM followed the second order kinetic model.

Enzymatic activities in constructed wetlands and di-n-butyl phthalate (DBP) biodegradation

The bioaccumulation of phthalate acid esters (PAEs) from industrial products and their mutagenic action has been suggested to be a potential threat to human health. The effects of the most frequently identified PAE, Di-n-butyl phthalate (DBP), and its biodegradation, were examined by comparison of two small scale plots (SSP) of integrated vertical-flow constructed wetlands. The influent DBP concentration was 9.84 mg l(-1) in the treatment plot and the control plot received no DBP. Soil enzymatic activities of dehydrogenase, catalase, protease, phosphatase, urease, cellulase, beta-glucosidase, were measured in the two SSP after DBP application for 1 month and 2 months, and 1 month after the final application. Both treatment and control had significantly higher enzyme activity in the surface soil than in the subsurface soil (P < 0.001) and greater enzyme activity in the down-flow chamber than in the up-flow chamber (P < 0.05). In the constructed wetlands, DBP enhanced the activities of dehydrogenase, catalase, protease, phosphatase and inhibited the activities of urease, cellulase and beta-glucosidase. However, urease, cellulase, beta-glucosidase activities were restored 1 month following the final DBP addition. Degradation of DBP was greater in the surface soil and was reduced in sterile soil, indicating that this process may be mediated by aerobic microorgansims. DBP degradation fitted a first-order model, and the kinetic equation showed that the rate constant was 0.50 and 0.17 d(-1), the half-life was 1.39 and 4.02 d, and the r(2) was 0.99 and 0.98, in surface and subsurface soil, respectively. These results indicate that constructed wetlands are able to biodegrade organic PA-Es such as DBP. (c) 2005 Elsevier Ltd. All rights reserved.

Kinetics of the oxidation of MCRR by potassium permanganate

The occurrence of the microcystins in the water bodies, especially in drinking water resources, has received considerable attentions. In situ chemical oxidation is a promising cost-effective treatment method to remove MC from water body. This research investigated the reaction kinetics of the oxidation of MCRR by permanganate. Experimental results indicate that the reaction is second order overall and first order with respect to both permanganate and MCRR, and has an activation energy of 18.9 kJ/mol. The second-order rate constant ranges from 0.154 to 0.225 l/mg/min at temperature from 15 to 30 degrees C. The MCRR degradation rates can be accelerated through increasing reaction temperature and oxidant concentration. The reaction under acid conditions was slightly faster than under alkaline conditions. The half-life of the reaction was less than 1 min, and more than 99.5% of MCRR was degraded within 10 min. (c) 2005 Elsevier Ltd. All rights reserved.

Photodegradation dynamics of pure microcystin variants with illumination of fixed wavelength UV-lights

Photolysis of microcystins by UV irradiation and the effects of different environmental factors on efficiency of UV degradation were studied. The results indicated that the rates of the photolytical degradation reactions of microcystin-LR and RR-follow pseudo-first-order kinetic process. The results also showed that the concentrations of two microcystin variants decreased significantly by UV-C Irradiation; the wavelength and intensitiy of UV irradiation are two very important factors affecting the rate of degradation; temperature and pH value could also affect the half life of degradation rates. When irradiated by weaker UV-Iight, isomerization could be detected in the course of photolytical degradation. The concentrations of two isomers transformed from microcystin-LR reached its maximum at the third minute and decreased with the time afterwards. To simulate photolysis of microcystins in the field water body, microcystins with low concentration were used. It was found that UV-C illumination was capable of decomposing over 95% of microcystins within 40 min. In the presence of humic substances the photodecomposition slowed down to a certain extent. These results are valuable in using UV irradiation for elimination microcystins from raw water.

Control of the lasing wavelength by a sampled grating in a complex-coupled DFB laser

The lasing wavelength of a complex-coupled DFB laser is controlled by a sampled grating. The key concepts of the approach are to utilize the -1st order (negative first order) reflection of a sampled grating for laser single mode operation, and use conventional holographic exposure combined with the usual photolithography to fabricate the sampled grating. The typical threshold current of the sampled grating based DFB laser is 32 mA, and the optical output is about 10 mW at an injected current of 100 mA. The lasing wavelength of the device is 1.5356 mu m, which is the -1st order wavelength of the sampled grating.

Raman scattering of non-planar graphite: arched edges, polyhedral crystals, whiskers and cones

Planar graphite has been extensively studied by Raman scattering for years. A comparative Raman study of several different and less common non-planar graphitic materials is given here. New kinds of graphite whiskers and tubular graphite cones (synthetic and natural) have been introduced. Raman spectroscopy has been applied to the characterization of natural graphite crystal edge planes, an individual graphite whisker graphite polyhedral crystals and tubular graphite cones. Almost all of the observed Raman modes were assigned according to the selection rules and the double-resonance Raman mechanism. The polarization properties related to the structural features, the line shape of the first-order dispersive mode and its combination modes, the frequency variation of some modes in different carbon materials and other unique Raman spectral features are discussed here in detail.

A novel design of grating couplers for efficient broadband coupling between silicon-on-insulator nanophotonic waveguides and fibres

A novel design of out-of-plane grating couplers is proposed for coupling between silicon-on-insulator nanophotonic waveguides and single-mode fibres. The coupler with the first-order diffraction coupling to the optical fibre is actually a second-order reflected grating with two times of period of the first-order grating. To enhance outcoupled power, a back hole is designed to form in the silicon substrate and a kind of metals is placed on the top acting as a reflection layer. The coupler is optimized using coupled-mode- based simulations, showing that, the coupling efficiency to and from tapered optical fibre can be as high as 85% with 1 dB bandwidth about 23nm.

Structural, photoluminescence, and field emission properties of vertically well-aligned ZnO nanorod arrays

The self-assembled growth of vertically well-aligned ZnO nanorod arrays with uniform length and diameter on Si substrate has been demonstrated via thermal evaporation and vapor-phase transport. The structural, photoluminescence (PL), and field emission properties of the as-prepared nanorod arrays were investigated. The PL spectrum at 10 K shows a strong and sharp near-band gap emission (NBE) peak ( full width at half-maximum (FWHM) = 4.7 meV) and a weak neglectable deep-level emission (DL) peak (I-NBE/I-DL= 220), which implies its good crystallinity and high optical quality. The room-temperature NBE peak was deduced to the composition of free exciton and its first-order replicas emissions by temperature-dependent PL spectra. The field emission measurements indicate that, with a vacuum gap of 400 Am, the turn-on field and threshold field is as low as 2.3 and 4.2 V/mu m. The field enhancement factor beta and vacuum gap d follows a universal equation.

Equilateral-triangle-resonator injection lasers with directional emission

Equilateral-triangle-resonator (ETR) lasers with an output waveguide jointed at one vertex of the resonator are fabricated on (100) GaInAsP-InP wafers using photolithography and a two-step inductively coupled plasma (ICP) etching technique. Distinct peaks with the mode spacing of longitudinal mode intervals are observed in the luminescence spectra at room temperature. Furthermore, some minor peaks appear in the middle of the main peaks, which can be attributed to the first-order transverse modes as predicted in the theoretical results. CW directional lasing emissions are achieved for ETR lasers with side lengths ranging from 15 to 30 pm up to 200 K. The temperature dependences of the threshold current and lasing wavelength are measured for an ETR laser with the side length of 20 mu m from 80 to 200 K. The observed threshold current rapidly increases as temperature increases over 170 K.