辽河坳陷东部凹陷火山岩构造裂缝形成机理研究及预测

In recent years, with the discovery oil and gas reservoirs in volcanic rocks, the exploration and development of these reservoirs have attracted widespread attention because of the urgent need for increasing oil and gas production in the world and volcanic rocks has currently become an important exploration target in Liaohe depression. The study area of this dissertation is in the middle section of the easternern sag of Liaohe depression that have been confirmed by studying structural fractures, which constitute a key factor impacting volcanic rocks reservoirs. Substantial reserves and large production capacity in the areas with widely distributed volcanic rocks are important reasons for examining volcanic rocks in the study area. The study began with classification and experimental data analysis of volcanic rocks fractural formation, then focused on the mechanism of fracturing and the development of volcanic rocks structural fracture prediction methodology.and Lastly, predicted volcanic rocks structural fracture before drilling involved a comprehensive study of the petroleum geology of this area, which identified favorable traps thereby reducing exploration risks and promoting the exploration and development of volcanic rocks reservoirs. 3Dstress and 3Dmove software were applied to predict structural fracture by combining the core data, well-logging data and seismic data together and making the visualization of a fracture possible. Base on the detailed fracture prediction results, well OuO48 and well Ou52 were drilled and successfully provided a basis for high efficiency exploration and development of fractured reservoir in the middle section of the eastern sag. As a result of what have been done, a new round of exploration of volcanic rocks was developed. Well OU48 and well OU52 successfully drilled in this area resulted in the in-depth study of the mechanism of structural fracture formation, technological innovation of structural fracture prediction of volcanic rocks , which guided to oil and gas exploration effectively and made it possible for high production of volcanic rocks. By the end of August 2005, the cumulative oil and gas production of Ou48 block were 5.1606 × 104 t and 1271.3× 104 m3 respectively, which made outstanding contributions to the oilfield development. Above all this work not only promoted exploration and structural fracture prediction in volcanic rocks in Liaohe depression, but also applied to in the low-permeability and fractured sandstone reservoir.

胜利勘探数据中心及勘探辅助决策系统研究

In the paper through extensive study and design, the technical plan for establishing the exploration database center is made to combine imported and self developed techniques. By research and repeated experiment a modern database center has been set up with its hardware and network having advanced performance, its system well configured, its data store and management complete, and its data support being fast and direct. Through study on the theory, method and model of decision an exploration decision assistant schema is designed with one decision plan of well location decision support system being evaluated and put into action. 1. Study on the establishment of Shengli exploration database center Research is made on the hardware configuration of the database center including its workstations and all connected hardware and system. The hardware of the database center is formed by connecting workstations, microcomputer workstations, disk arrays, and those equipments used for seismic processing and interpretation. Research on the data store and management includes the analysis of the contents to be managed, data flow, data standard, data QC, data backup and restore policy, optimization of database system. A reasonable data management regulation and workflow is made and the scientific exploration data management system is created. Data load is done by working out a schedule firstly and at last 200 more projects of seismic surveys has been loaded amount to 25TB. 2. Exploration work support system and its application Seismic data processing system support has the following features, automatic extraction of seismic attributes, GIS navigation, data order, extraction of any sized data cube, pseudo huge capacity disk array, standard output exchange format etc. The prestack data can be accessed by the processing system or data can be transferred to other processing system through standard exchange format. For supporting seismic interpretation system the following features exist such as auto scan and store of interpretation result, internal data quality control etc. the interpretation system is connected directly with database center to get real time support of seismic data, formation data and well data. Comprehensive geological study support is done through intranet with the ability to query or display data graphically on the navigation system under some geological constraints. Production management support system is mainly used to collect, analyze and display production data with its core technology on the controlled data collection and creation of multiple standard forms. 3. exploration decision support system design By classification of workflow and data flow of all the exploration stages and study on decision theory and method, target of each decision step, decision model and requirement, three concept models has been formed for the Shengli exploration decision support system including the exploration distribution support system, the well location support system and production management support system. the well location decision support system has passed evaluation and been put into action. 4. Technical advance Hardware and software match with high performance for the database center. By combining parallel computer system, database server, huge capacity ATL, disk array, network and firewall together to create the first exploration database center in China with reasonable configuration, high performance and able to manage the whole data sets of exploration. Huge exploration data management technology is formed where exploration data standards and management regulations are made to guarantee data quality, safety and security. Multifunction query and support system for comprehensive exploration information support. It includes support system for geological study, seismic processing and interpretation and production management. In the system a lot of new database and computer technology have been used to provide real time information support for exploration work. Finally is the design of Shengli exploration decision support system. 5. Application and benefit Data storage has reached the amount of 25TB with thousand of users in Shengli oil field to access data to improve work efficiency multiple times. The technology has also been applied by many other units of SINOPEC. Its application of providing data to a project named Exploration achievements and Evaluation of Favorable Targets in Hekou Area shortened the data preparation period from 30 days to 2 days, enriching data abundance 15 percent and getting information support from the database center perfectly. Its application to provide former processed result for a project named Pre-stack depth migration in Guxi fracture zone reduced the amount of repeated process and shortened work period of one month and improved processing precision and quality, saving capital investment of data processing of 30 million yuan. It application by providing project database automatically in project named Geological and seismic study of southern slope zone of Dongying Sag shortened data preparation time so that researchers have more time to do research, thus to improve interpretation precision and quality.

东濮凹陷低阻油层形成机理与评价方法研究

In order to effectively identify and accurately evaluate low resistivity reservoir in Dongpu depression, using various logging data synthetically, geological and logging characteristics are summarized in term of different blocks on the basis of core analysis, cutting logging, oil testing and commissioning data. The formation mechanism of low resistivity reservoir is studied, and the main factors that cause low resistivity reservoir are discovered. The first factor is fine lithology, high shale content and hydrophilic rock. The second factor is high salinity formation water. The third factor is light oil, high gas quantity dissolved and large difference density of oil-water. The last factor is low amplitude structure of reservoir and low differential degree of oil-water. According to the characteristics of low resistivity reservoir, the method of compound lithology, the method of movable fluid, the method of phase permeability and the method of nuclear magnetic resonance logging are put forward. The compound lithology criterion of distinguishing hydrocarbon is founded in term of different blocks on the basis of electrical efficiency. The evaluation models of reservoir parameters are founded; whose core is oil saturation and phase permeability. In order to calculate oil saturation, the compound lithology model on the basis of electrical efficiency theory is chosen on condition that there is only the combination logging data of acoustic and induction; the W-S model is chosen on condition that there is all-around logging data. The calculational precision of oil saturation in low resistivity reservoir of work area is enhanced when the selection method is utilized. There are 1212 layers of reservoir newly added by the old well reexamination in the ten oil areas. The coincidence rate of logging interpretation reaches 83.2 percent according to the 74 well-times of oil testing or commissioning, which indicates that the distinguishing method and evaluation models of low resistivity reservoir above are feasible.By the reexamination, a ten million tons of proved reserves related to the low resistivity reservoir are newly added, consequently, the groundwork is established to increase reserve and production of old oilfields in the east of China and new livingness is added for the petroleum exploration and development in Dongpu depression.

孤岛油田油藏动态模型和开发环境及剩余油分布

This paper is an important part of the national "863" topic :"Reservoir dynamic model, the development environment and the forecast of remaining oil". In this paper, multi-theory, method and technology are synthesized, and sufficiently use the computer method. We use unifies of qualitative and quota, unifies of macroscopic and microscopic, unifies of dynamic and quiescent description of reservoir, unifies of comprehensive research about reservoir and physical mathematical simulation, unifies of three-dimensional and four-dimensional description of reservoir to research the reservoir of channel sand in Gudao oilfield. and we do some research about the last 10 years of the more than 30 year high pressure water injection and polymer water flooding development, dynamic changes and geologic hazard of reservoir fluid field. It discloses the distribution, genesis and controlling factors. The main innovation achievement and the understanding are: we built-up the framework of the strata and structure, and found genetic type, spatial distribution and aeolotropism of the upper Guantao member. We form the macroscopic and microscopic reservoir model of dynamic evolution, disclose the character, distribution of the macroscopic and microscopic parameter，and the relationship with remaining oil. Next we built-up the model about hydrosialite, and find the styles, group of styles, formation mechanism and controlling factors of the reservoir, disclose the affection of the hydrosialite to remaining oil, pollution of the production environment of oilfield and geologic hazard. The geologic hazards are classified to 8 styles first time, and we disclose the character, distribution law, formation mechanism and controlling factors of the geologic hazard. We built-up the model of the distribution of remaining oil in different periods of Gudao oilfield, and disclose the macroscopic and microscopic formation mechanism of remaining oil in different periods, forecast the distribution of the mobile remaining oil, and find that the main cause of the dynamic evolution of all the sub-models of reservoir fluid field is the geologic process of the reservoir development hydrodynamic force. We develop the reservoir fluid field, research of environment disaster and the description about the support theory, method and technology. The use of this theory in Gudao oilfield has obtained very good economic efficiency, and deepened and develops development geology about the continental facies fault-trough basin, and theory of geologic hazard.

子洲—清涧地区上古生界储层综合研究

The exploration and study in recent years shows that the upper Paleozoic in the east of Ordos Basin possesses major exploration potential, so it is necessary to have a comprehensive and synthetic research in this area. Following the guideline of T.A. Cross’s high resolution sequences stratigraphy and combined with sedimentology, the strata and sequence in the research area are divided and correlated. This paper emphasizes on the reservoir in this area and its major fruits are: Firstly, form the framework of the high sequence stratigraphy through mainly studying on the data of core, well drilling and field section combining. Then, think that the best reservoir formation mainly appears in the middle or lower part of long arising semi-cycle, and focus on A type and C1 middle sequence cycle that contributes to the development of formation. Next, think the sedimentary source mainly comes from the epimetamorphic crystalline basement in the north of the Ordoes Basin through analyzing depositional background, researching on sandstone petrography, distribution characteristics of the sedimentary system as well as researching on heavy mineral combination characteristics. Fourthly, give priority to Zizhou-Qingjian area for the first time and gain seven lithofacies paleography maps in the No.2 member of Shanxi and the No.8 member of Shihezi through using the method of isochronal lithofacies paleogeography mapping, then bring forth that Sh2 is mainly developed a type I sequence under the margin of ramp lake-basin background. Fifthly, through researching on the characteristics of reservoir petrography and diagenesis, think that all researched areas experienced compaction and cementation, and there is different types of rocks, only little of the primary pores that are made up of litharenite and lithoclastic quartz sandstone is left, while in lithoclastic quartz sandstone, there are still many primary pores Sixthly, through studying on pore types, microstructure, as well as physical property on the key formation, think that the researched area mostly appears typical low pore, low porosity and permeability, which mainly result from sedimentary and diagenesis. Lastly, through researching on classified evaluation in the key formation, productivity analysis, and combing with reservoir distribution, the researched area is divided into three parts, and think that exploration should be emphasized on formation I and II. The characteristics of sandstones distribution in Sh23 member, gas formation distribution and open flow capacity of exploitation well are all consistent properly with the results of reservoir comprehensive evaluation in this thesis proved by the gas production development in 2006.

胜坨油田注聚后油藏动态模型及剩余油分布

The topic of Dynamic reservoir model and the distribution of remaining oil after polymer injection of Shengtuo oilfield is a front problem of "the 11th Five-Year Plan" scientific and technological disciplines of Sinopec Corporation. Reservoirs in study area is distributary channel sandstone. After 34 years of water-injection exploitation and 7 years of polymer injection pilot experiments, a highly complex heterogeneous dynamic evolution has been occurred in macro and micro parameters of reservoir model, together with its flow field. Therefore, it’s essential to construct completed reservoir dynamic model for a successfully prediction of the distribution of remaining oil. With a comprehensive application of multidisciplinary theory and technique, using a variety of data and information to maximize the use of computer technology, combining a static and dynamic, macro and micro and 1~4D integration, the research reveals main features, evolution and mechanism, types of geological disasters and their destructivity of reservoir flow field, the macro field, the micro field, the flow field and reservoir development hydrodynamic geological function in different development periods after a long term of polymer injection in Es2 in Shengtuo oilfield. The principle innovation achievements obtained are: 1. Established A, B, C, D four flow units in target formations, revealed the various features and distribution of flow units. 2. Stated environmental pollution and geological disasters induced during oilfield exploitation in study area, and also explained their formation mechanism, controlling factors, destructivity and approaches to disaster reduction. 3. Established dynamic evolution of the macro parameter model, micro-matrix field, pore network field, clay minerals field, seepage dynamic evolution model of six different exploitation stages in study area, also revealed reservoir flow evolution, the law of evolution mechanism after polymer injection. 4. Established macro and micro distribution model of remaining oil after three mining polymer injection during different water cut periods in study area, revealed the formation mechanism and distribution of remaining oil. 5. Established remaining oilforecasting model in study area, and forecasted the formation and distribution of remaining oil in the following six years. 6. It is proposed that reservoir fluid dynamic geological processes are major driving forces for the evolution of different water cut periods, reservoir macro field after the polymer injection and micro seepage field. 7. Established a dynamic reservoir model, proposed matching theory, methods and technology for the description of the remaining oil characterization and prediction, which can deepen the theory and techniques of continental rift basin development geology. Key words: Polymer reservoir; Geological disasters; Dynamic model; Residual oil forecast

地下水位上升造成的黄土远程滑坡形成机理与数值模拟研究

Based on field survey, laboratory testing and numerical modeling, engineering characteristics of undisturbed loess and the mechanism of long-runout loess landslides caused by underground water level rise, as well as the formation conditions and spatial distribution of landslides, are systematically studied and analyzed. Loess landslides at south Plateau of Jingyang County are mainly classified as flowslide, slide and fall. Flowslide is the main type characteristic of high velocity, long runout and multi-stages. The steep relief composed of loose structured loess-old aged soil serials and the rise of groundwater table are the predominant conditions for landslides in the study area. To study loess mechanic poperties and loess landslides mechanisims, isotropically and anisotropically consolidated undrained compression(ICU and ACU) tests and constant-deviator-drained compression (CQD) tests were carried out on undisturbed samples. The results of undrained compression tests performed at the in-situ stress level show that the soils are of consistently strain-softening in the stress-strain relations and cause high excess pore pressure. The steady-state line and the potential region of instability are obtained from ICU and ACU test results. A necessary condition for liquefaction is that the soil state initially lies in or is brought into the potential instability region. In addition, a strong strain-softening model is also formed. CQD tests demonstrate that the mobilized friction angle is far less than the steady-state angle and that the soil experiences undrained contractive failure suddenly at very small strains when its stress path during drained loading tries to cross the potential instability region，thus validates the proposed instability region. Based on the location of the region of potential instability and the stress state of slope soil, a method of static liquefaction analysis is proposed for loess landslides caused by rise in groundwater table. Compared with other liquefaction analysis methods, this method overcomes the limitations inherent in conventional slope stability method and undrained brittleness index method. Triaxial tests composed of constant water content (CW) and wetting tests at constant deviator stress are performed on undisturbed unsaturated samples. The stress-strain relation of CW tests takes on strain-hardening behavior; The results of wetting tests at constant deviator stress designed to study the mechanics of failure of unsaturated loess caused by an increase in the degree of saturation (wetting) shows that a contractive failure occurs in the undisturbed samples. On the basis of the above triaxial test results, the initiation of static liquefaction is presented for long-runout loess landslides caused by rise in groundwater table, that is, the loess slope soil gradually transfer from unsaturated to saturated state under the infiltration of irrigation. A contractive failure occurs in the local region at very small strain by increasing the pore-water pressure at constant deviator stresses under drained conditons. It is the contractive failrue resulting from rise of pore pressure that leads to high excess pore pressure in the neighbour soil which reduces shear resistance of soil. The neighbour soils also fail due to the rapid increase in pore-water pressure. Thus a connected failure surface is developed quickly and a flowslide occurs. Based on the saturated-unsaturated seepage theory, transient seepage is computed using the finite element method on loess slope under groundwater table rise. Pore-water pressure distribution for every time step after irrigation are obtained. The phreatic surface in the slope increases with the groundwater table. Pore-water pressure distribution within 8m above the phreatic surface changes very quickly，but the water content and pore water pressure in the region ranging from 8m above the phreatic surface up to ground surface is almost not affected and the matric suction usually is kept at 100～120 kPa. Based on the results of laboratory tests and seepage flow analysis, the development process of loess landslide is modeled considering groundwater table rise. The shearing plastic zone first occurs at the slope toe where the soil is soaked for long term during rise in groundwater table. As irrigation continues, the shearing plastic zone gradually extends to the interior soils, with the results that the tensile plastic zone occurs at the slope crown. As time goes on, both the shearing plastic zone and tensile plastic zone continue to extend. Then a connected plastic zone is formed and fowslide occurs. In comparision to laboratory test results, the results of numerical simulation quite well verify the presented mechanism of static liquefaction of long-runout loess landslides caused by rise in groundwater table.

松辽盆地南部大情字井地区CO2埋存体地质格架及储层建模

Increasing attentions have been paid to the subsurface geological storage for CO2 in view of the huge storage capacity of subsurface reservoirs. The basic requirement for subsurface CO2 storage is that the CO2 should be sequestrated as supercritical fluids (physical trapping), which may also interact with ambient reservoir rocks and formation waters, forming new minerals (chemical trapping). In order to the effective, durable and safe storage for CO2, enough storage space and stable sealing caprock with strong sealing capacity are necessitated, in an appropriate geological framework. Up till now, hydrocarbon reservoirs are to the most valid and appropriate CO2 storage container, which is well proven as the favorable compartment with huge storage capacity and sealing condition. The thesis focuses on two principal issues related to the storage and sealing capacity of storage compartment for the Qingshankou and Yaojia formations in the Daqingzijing block, Southern Songliao Basin, which was selected as the pilot well site for CO2-EOR storage. In the operation area, three facies, including deltaic plain, deltaic front and subdeep-deep lake facies associations, are recognized, in which 11 subfacies such as subaqueous distributary channel, river- mouth bar, interdistributary bay, sheet sandbody, crevasse splay and overflooding plain are further identified. These subfacies are the basic genetic units in the reservoir and sealing rocks. These facies further comprise the retrogradational and progradational depositional cycles, which were formed base- level rise and fall, respectively. During the regressive or lake lowstand stage, various sands including some turbidites and fans occurred mostly at the bottom of the hinged slope. During the progradation stage, these sands became smaller in size and episodically stepped backwards upon the slope, with greatly expanded and deeped lake. However, most of Cretaceous strata in the study area, localized in the basin centre under this stage, are mainly composed of grey or grizzly siltstones and grey or dark grey mudstones intercalated with minor fine sandstones and purple mudstones. On the base of borehole and core data, these siltstones are widespread, thin from 10 to 50 m thick, good grain sorting, and have relative mature sedimentary structures with graded bedding and cross- lamination or crossbeds such as ripples, which reflect strong hydrodynamic causes. Due to late diagenesis, pores are not widespread in the reservoirs, especially the first member of Qingshankou formation. There are two types of pores: primary pore and secondary cores. The primary pores include intergranular pores and micropores, and the secondary pores include emposieus and fracture pores. Throat channels related to pores is also small and the radius of throat in the first, second and third member of Qingshankou formation is only 0.757 μm, 0.802 μm and 0.631 μm respectively. In addition, based on analyzing the probability plot according to frequency of occurrence of porosity and permeability, they appear single- peaked distribution, which reflects strong hetero- geneity. All these facts indicate that the conditions of physical property of reservoirs are not better. One reason may be provided to interpret this question is that physical property of reservoirs in the study area is strong controlled by the depositional microfacies. From the statistics, the average porosity and permeability of microfacies such as subaqueous distributary channel, channel mouth bar, turbidites, is more than 9 percent and 1md respectively. On the contrary, the average porosity and permeability of microfacies including sand sheet, flagstone and crevasse splay are less than 9 percent and 0.2md respectively. Basically, different hydrodynamic environment under different microfacies can decide different physical property. According to the reservoir models of the first member of Qingshankou formation in the No. well Hei47 block, the character of sedimentary according to the facies models is accord to regional disposition evolution. Meantime, the parameter models of physical property of reservoir indicate that low porosity and low permeability reservoirs widespread widely in the study area, but the sand reservoirs located in the channels are better than other places and they are the main sand reservoirs. The distribution and sealing ability of fault- fractures and caprock are the key aspects to evaluate the stable conditions of compartments to store CO2 in the study area. Based on the core observation, the fractures widespread in the study area, especially around the wells, and most of them are located in the first and second member of Qingshankou formation, almost very few in the third member of Qingshankou formation and Yaojia formation instead. In addition, analyzing the sealing ability of eleven faults in the three-dimensional area in the study area demonstrates that most of faults have strong sealing ability, especially in the No. well Hei56 and Qing90-27. To some extent, the sealing ability of faults in the No. well Hei49, Qing4-6 and Qing84-29 are worse than others. Besides, the deposition environment of most of formations in the study area belongs to moderately deep and deep lake facies, which undoubtedly take advantage to caprocks composed of mudstones widespread and large scale under this deposition environment. In the study area, these mudstones distribute widely in the third member of Qingshankou formation, Yaojia and Nenjiang formation. The effective thickness of mudstone is nearly ~550m on an average with few or simple faults and fractures. In addition, there are many reservoir beds with widely- developed insulated interbeds consist of mudstones or silty mudstone, which can be the valid barrier to CO2 upper movement or leakage through diffusion, dispersion and convection. Above all, the closed thick mud caprock with underdeveloped fractures and reservoir beds can be taken regard as the favorable caprocks to provide stable conditions to avoid CO2 leakage.

地震P-S波时差耦合作用的斜坡崩滑效应研究

China locates between the circum-Pacific and the Mediterranean-Himalayan seismic belt. The seismic activities in our country are very frequent and so are the collapses and slides of slope triggered by earthquakes. Many collapses and slides of slope take place mainly in the west of China with many earthquakes and mountains, especially in Sichuan and Yunnan Provinces. When a strong earthquake happening, the damage especially in mountains area caused by geological hazards it triggered such as rock collapses, landslides and debris flows is heavier than that it caused directly. A conclusion which the number of lives lost caused by geological hazards triggered by a strong earthquake in mountains area often accounts for a half even more of the total one induced by the strong earthquake can be made by consulting the statistical loss of several representative earthquakes. As a result, geological hazards such as collapses and slides of slope triggered by strong earthquakes attract wide attention for their great costs. Based on field geological investigation, engineering geological exploration and material data analysis, chief conclusions have been drawn after systematic research on formation mechanism, key inducing factors, dynamic characteristics of geological hazards such as collapses and slides of slope triggered by strong earthquakes by means of engineering geomechanics comprehensive analysis, finite difference numerical simulation test, in-lab dynamic triaxial shear test of rock, discrete element numerical simulation. Based on research on a great number of collapses and landslides triggered by Wenchuan and Xiaonanhai Earthquake, two-set methods, i.e. the method for original topography recovering based on factors such as lithology and elevation comparing and the method for reconstructing collapsing and sliding process of slope based on characteristics of seism tectonic zone, structural fissure, diameter spatial distribution of slope debris mass, propagation direction and mechanical property of seismic wave, have been gotten. What is more, types, formation mechanism and dynamic characteristics of collapses and slides of slope induced by strong earthquakes are discussed comprehensively. Firstly, collapsed and slided accumulative mass is in a state of heavily even more broken. Secondly, dynamic process of slope collapsing and sliding consists of almost four stages, i.e. broken, thrown, crushed and river blocked. Thirdly, classified according to failure forms, there are usually four types which are made up of collapsing, land sliding, land sliding-debris flowing and vibrating liquefaction. Finally, as for key inducing factors in slope collapsing and sliding, they often include characteristics of seism tectonic belts, structure and construction of rock mass, terrain and physiognomy, weathering degree of rock mass and mechanical functions of seismic waves. Based on microscopic study on initial fracturing of slope caused by seismic effect, combined with two change trends which include ratio of vertical vs. horizontal peak ground acceleration corresponding to epicentral distance and enlarging effect of peak ground acceleration along slope, key inducing factor of initial slope fracturing in various area with different epicentral distance is obtained. In near-field area, i.e. epicentral distance being less than 30 km, tensile strength of rock mass is a key intrinsic factor inducing initial fracturing of slope undergoing seismic effect whereas shear strength of rock mass is the one when epicentral distance is more than 30 km. In the latter circumstance, research by means of finite difference numerical simulation test and in-lab dynamic triaxial shear test of rock shows that initial fracture begins always in the place of slope shoulder. The fact that fracture strain and shear strength which are proportional to buried depth of rock mass in the place of slope shoulder are less than other place and peak ground acceleration is enlarged in the place causes prior failure at slope shoulder. Key extrinsic factors inducing dynamic fracture of slope at different distances to epicenter have been obtained through discrete element numerical simulation on the total process of collapsing and sliding of slope triggered by Wenchuan Earthquake. Research shows that combined action of P and S seismic waves is the key factor inducing collapsing and sliding of slope at a distance less than 64 km to initial epicenter along earthquake-triggering structure. What is more, vertical tensile action of P seismic wave plays a leading role near epicenter, whereas vertical shear action of S seismic wave plays a leading role gradually with epicentral distance increasing in this range. On the other hand, single action of P seismic wave becomes the key factor inducing collapsing and sliding of slope at a distance between 64 km and 216 km to initial epicenter. Horizontal tensile action of P seismic wave becomes the key factor gradually from combined action between vertical and horizontal tensile action of P seismic wave with epicentral distance increasing in this distance range. In addition, initial failure triggered by strong earthquakes begins almost in the place of slope shoulder. However, initial failure beginning from toe of slope relates probably with gradient and rock occurrence. Finally, starting time of initial failure in slope increases usually with epicentral distance. It is perhaps that the starting time increasing is a result of attenuating of seismic wave from epicenter along earthquake-triggering structure. It is of great theoretical and practical significance for us to construct towns and infrastructure in fragile geological environment along seism tectonic belts and conduct risk management on earthquake-triggered geological hazards by referring to above conclusions.

中国大陆地区远震体波接收函数与岩石圈厚度的研究

Movements of separation and convergence between the continental plates, as well as the interaction beween the lithosphere and asthenosphere is the dominant factor in plate evolution. Moreover, those phenomena, the formation, enrichment and storage of energy and mineral strorage, as well as intraplate earthquakes are all relate to plate movement and evolution. Therefore, the study of continental lithosphere, is not only helpful to analysing the dynamic model between lithosphere and asthenoshere as well as different plates, but also important to the nation's economy and the people's livelihood. And the lithospheric thickness or Lithosphere-Asthenosphere Boundary (LAB) is one of the most important parameters in study of continental lithospheric formation and evolution. Chinese continent composed by many small plates, possesses diverse type of lithospheric structure. But our knowledge ahout Chinese continental lithosphere, especially the regional research, is almost based on the low-resolution results of surface wave dispersion analysis and seismic wave tomography. Howere, recently a technique employing S-to-P converted body waves (the S receiver function technique) has been developed that can be used to identify the LAB with a higher resolution. This thesis has collected waveform data of 232 broadband seismic stations that are located in China and neighboring regions. Using teleseismic S-wave and P-wave receiver functions have studied the Chinese continental lithospheric structure. The results of this study indicate that, the thickness of Chinese continental lithosphere become thinner from west to east, and obvious difference exists between different blocks. Four types of lithosphere have been detected: (1) Convergence thicking lithosphere in Tibetan Plateau; (2) Stable lithosphere in Tarim basin and upper Yangtze craton; (4) Active lithosphere in Orogenic belts; (4) Break-up thinning lithosphere in east China craton

藏北可可西里碰撞后钾质火山作用和岩石成因

Post-collisional, potassic igneous rocks are widely distributed in the Hoh Xil area of the northern Tibetan Plateau. Based on the field work, petrography, mineral chemistry, K-Ar geochronology, element and Sr-Nd-Pb isotope geochemistry, this thesis systematically studied the spatial and temporal distribution of the volcanic rocks, chemical characteristics, formation mechanism and partial melting mechanism of the magma source region, geodynamic setting of magmatism, as well as crustal assimilation and fractional crystallization (AFC). The results show that: 1. The Miocene (7.77-17.82 Ma) volcanic products dominantly are trachandesite and trachy, and subordinate rhyolites, associated with stike-slip faults and thrust faults, formed morphology of small lava platforms and cinder cones. 2. Phenocrysts in the lavas are augite, andesine, sanidine, calcic amphibole and subordinate orthopyroxene, biotite and Ti-Fe oxides, displaying typical quench texture. Equilibrium temperatures and pressures of clinopyroxene phenocrysts indicate the magma chamber is located in upper-middle crust. 3. Rhyolites are the products of crustal melting and fractionation of shoshonitic magmas. The source region of intermediate magmas is enriched continental lithospheric mantle, which contains residual minerals such as phlogopite, rutile and spinel, and enriched by subducted sediments during earlier multi-episodes of subduction. 4. Upwelling of asthenosphere provides heat for source region melting, and faults provide channels for magma eruption. 5. Northward underthrusting of Indian continental lithosphere and southward of backstop of Asian continental lithosphere resulted in upwelling of hot asthenosphere. Geochemical characteristics of the potassic magmatism in North Tibet are dominantly controlled by source region composition, partial melting, and crustal assimilation and fractional crystallization (AFC).

西南极南设得兰群岛中新生代火山岩基底沉积学及其大地构造制约

Livingston Island, the second island of South Shetland Island, constains Mesozoic-Cenozoic basement, Mesozoic-Cenozoic volcanic sequences, plutonic intrusions and post-subduction volcanic rocks, which document the history and evolution of an important part of the South Shetland Islands magmatic arc. The sedimentary sequence is named the Miers Bluff Formation (MBF) and is interpreted as turbidite since the first geological study on South Shetland Islands, and is interpreted as turbidite. It base and top are not exposed, but a thickness of more than 3000m has been suggested and seems plausible. The turbidite is overlain by Mid - Cretaceous volcanic rocks and intruded by Eocene tonalites. The age of the Miers Bluff Formation is poorly constrained Late Carboniferous -Early Triassic. Sedimentary Environment, tectonic setting and forming age of sedimentary rocks of the Miers Bluff Formation were discussed by means of the methods of sedimentology, petrography and geochemistry, combinig with the study of trace fossils and microfossil plants. The following conclusions are obstained. A sedimentary geological section of Johnsons Dock is made by outside measuring and watching, and then according the section, the geological map near the Spanish Antarctic station was mapped. Four pebbly mudstone layers are first distinguished, which thickness is about 10m. The pebbly mudstone is the typical rock of debris flow, and the depostional environment of pebbly mudstone may be the channel of mid fan of submarine fan. The sedimentsry structural characteristics and size analysis of sandstones show the typical sedimentary feature of turbidity flow and the Miers Bluff Formation is a deep-water turbidite (include some gravity-flow sediments). The materials of palaeocurrents suggest the continental slope dip to southeast, and indicate the provenance of turbidity sediment in the northwest area. By facies analysis, six main facies which include seven subfacies were recognized, which are formed in mid-fan and lower-fan of submarine, meanwhile, the sedimentary features of each facies and subfacies are summarized. The study of clastic composition, major elements, trace elements and rare earth elements indicates the forming setting of the Miers Bluff Formaton is active continental margin and continental island arc and the provenance is dissected magmatic arc which main composition is felsic gneiss. Many trace fossils of the whole succession were found in the turbidites of the Miers Bluff Formation. All these trace fossils are deep sea ichnofossils. There are fifteen ichnogenus, sixteen ichnospecies. Moreover, a new trace fossil was found and a new ichnogenus and new ichnospecies was proposed - Paleaichnus antarctics ichnogen, et ichnosp, nov.. Except the new ichnogenus and ichnospecies, others had been found in deep-sea flysch turbidites. Some are in mudstone and are preserved in the cast convex of overlying sandstone sole, they formed before turbidity flows occurred and belong to the high-different Graphoglyptida of fiysch mudstone. Others as Fucusopsis and Neonereites are preserved in sandstones and stand for trace assemblages after turbidity sedimentation. These trace fossils are typical members of abyssal "Nereites" ichnofacies, and provide for the depositional environment of the Miers Bluff Formation. Fairly diverse microfossil plants have been recovered from the Miers Bluff Formation, Livingston Island, including spores, pollen, acritarchs, wood fragments and cuticles. Containing a total of about 45 species (forms) of miospores, the palynofiora is quantitatively characterized by the dominance of non-striate bisaccate pollen, but spores of pteridophytes and pollen of gymnosperms are proportionate in diversity. It is somewhat comparable to the subzone C+D of the Alisporites zone of Antarctica, and the upper Craterisporites rotundus zone and the lower Polycingulatisporites crenulatus zone of Australia, suggesting a Late Triassic (possibly Norian-Rhaetian) age, as also evidenced by the sporadic occurrence of Aratrisporites and probable Classopollis as well as the complete absence of bisaccate Striatiti. The parent vegetation and paleoclimate are preliminarily deduced. At last, the paper prooses the provenance of sedimentary rocks of the Miers Bluff Formation locates in the east part to the southern Chile(or Southern South American). In the Triassic period, contrasting with New Zealand, Australia and South American of the Pacific margin of Gondwanaland, the Miers Bluff Formation is deposited in the fore-arc basin or back-arc basin of magmatic arc.

三角洲储层孔隙结构模型与剩余油分布研究——以临南油田沙河街组储层为例

The study of pore structure in reservoir was paid attention to in the early reservoir research and now a systematic research methodology is set up. On the limits of tools and conditions, methodologies and technologies on formation condition and distribution laws of pore structure and the relationship between remaining oil distribution and pore structure are uncertain and some knownage about it is also uncertain. As the development of petroleum industry, the characterization of pore structure and the prediction of remaining oil are the hot spot and difficult point in the research of oil development. The author pays a close attention to this subject and has done much research on it. In a case study in Linnan oilfield Huimin sag Jiyang Depression Bohai Bay basin by using a new method, named varied scale comprehensive modeling of pore structure, the author builds pore structure models for delta reservoir, reveals the remaining oil distribution laws in delta facies, and predicts the distribution of remaining oil in Linnan oilfield. By the application of stratigraphy, sedimentology and structure geology. the author reveals the genetic types of sandbody and its distribution laws, builds the reservoir geological models for delta sandstone reservoir in Shahejie group in Linnan oilfield and points out the geological Factors that control the development of pores and throats. Combining petrology and the reservoir sensitive analysis, the author builds the rock matrix models. It is the first time to state that rocks in different sentimental micro facies have different sensitive .response to fluid pressed into the rocks. Normally. the reservoirs in the delta front have weaker sensitivity to fluid than the reservoirs in delta plain, In same subfacies, the microfacies that have fine grain, such as bank and crevasse splay, have stronger reservoir sensitivity than the microfacies that have coarse grains, such as under-water branched channel and debauch bar. By the application of advanced testing, such as imagine analysis, scan electronic microscope, and morphology method, the author classifies the pore structure and set up the distribution models of pore, throat and pore structure. By the application of advanced theory in well-logging geology, the author finds the relationship between microscope pore structure and macroscopic percolation characteristics, and then builds the well-logging interpretation formulae for calculating pore structure parameters. By using the geostatistics methods, the author reveals the spatial correlative characteristics of pore structure. By application of conditional stochastic simulation methods, the author builds the 3D models of pore structure in delta reservoir. It is the base of predicting remaining oil distribution. By a great deal of experiments and theoretical deduction, The author expounds the laws of percolation flow in different pore structures, and the laws by which the pore structure controls the micro distribution of remaining oil, and then, states the micro mechanism of remaining oil distribution. There are two types of remaining oil. They are by-pass flow caused by micro-fingering and truncation caused by non-piston movement. By new method, the author states the different pore structure has different replacement efficiency, reveals the formation condition and distribution laws of remaining oil. predicts the remaining oil distribution in Linnan oil field, and put forward some idea about how to adjust the oil production. The study yielded good results in the production in Linnan oilfield.

松辽徐家围子断陷层序地层充填模式及含油气性特征

Based on the principle and method of sequence, the author describes the sequence-filling model of the rifting basin of Xujiaweizi and its gas exploration potential. The object of this paper belongs to the area around Shengping-Wangjiatun anticline. Its srtatigraphy includes Huoshiling Formation (neutral and basic volcanic rocks), Shahezi Formation (coal bedding and mud and some sandstone) and Yingcheng Formation from bottom to top. These stratigraphy units are defined by author as mesosequences respectively. The author emphasizes that the main control factors of sequence change with the types of basin and stage of basin. So the sequence is researched according to the types of basin. This viewpoint is very new, and it is consistent with the principle of sequence. Volcanic action is very frequent and acute, topography difference is obvious. Between the volcanic events, Shahezi Formation is formed, which mainly consists-of sedimentary rocks. Based on the datum from seismic section and drilling core and well-logging, the author analyzes the single unit and unit set and system tract and sedimentary fancies, then, according to the accommodation space change and marking of sequence boundary, Shahezi Formation is divided into two Third-scale sequences. The sedimentary fancies and depth distribution are described. The author also pointed out that the volcanic rocks consume the accommodation space, so volcanic rocks can influence the development of sequence. Based on the concept of accommodation space, the author put volcanic rocks into sequence frame, which normally consists of sedimentary rocks. The topography of volcanic is controlled by lithology of volcanic rocks, the pattern of volcanic eruption and the topography before volcanic eruption. The topography of volcanic can influence sedimentation and the filling pattern of sedimentary rocks. The author describes the composition and lithology fancies and depth distribution of volcanic rocks. The volcanic rocks and Volcanic building, volcanic structure is recognized on seismic section. The author paid a special attention to the relationship between sedimentation and volcanism. Finally, the author analyses the combination of source-reservoir-cover unit in sequence frame. The mudstone of Shahezi Formation has a great depth, the Kerogene in it belongs to type II and III, which tends to produce gas. The Yingcheng Formation lies between Shahezi Formation and Denglouku Formation, belonging to good reservoir. The volcanic rocks of Huoshiling Formation often formed high building, which can capture the gas produced from Shahezi Formation. The stratigraphy of rifting basin of Xujiaweizi has the great potential of gas exploration. This paper claims the following creative points: 1. The author applied the principle and method of sequence to rifting basin, greatly extending its research area and topic issues. 2. The author pointed out that basin of different type and of different stage has a different type of sequence. This is caused by the different main control factors of sequence. 3. Put volcanic rocks into the sequence frame, discussing the probability of regarding the volcanic rocks as the component of sequence, dealing with the relationship between sedimentation and volcanism and its influence to the source-reservoir-cover system. 4. The author pointed out that the filling pattern of rifting basin are determined by the filling pattern of megasequence, whose filling pattern is determined by the filling pattern of system tract and the change of accommodation space.

沾化凹陷火成岩油气藏形成条件和分布规律研究

As a kind of special lithologic ones, Igneous rock oil and gas pool is more and more paid attention, and it has different forming condition and distribution from conventional ones, such as various terrane distribution types, serious reservoir anisotropy, complicated hydrocarbon-bearing, so there is not successful experience to follow for exploration and development of this complex subtle oil and gas pool at present. For an example of Igneous oil and gas pool of Luo151 area in Zhanhua seg, Eastern China, this article study the difficult problem, including petrologic nd lithofacies analysis, Origin, invasion age and times of Igneous rock, reservoir anisotropy, Geological Modeling, Igneous reservoir synthesis evaluation. forming condition and distribution are studied synthetically, and an integrated method to predict igneous rock oil and gas pool is formed, which is evaluated by using development data. The Igneous rock is mainly diabase construction in Luo151 area of Zhanhua Sag, and petrologic types include carbonaceous slate, hornfels, and diabases. Based on analyzing synthetically petrologic component, texture and construct, 4 lithofacies zones, such as carbonaceous slate subfacies, hornfels subfacies containing cordierite and grammite, border subfacies and central subfacies, are divided in the diabase and wall rock. By studying on isotopic chronology, terrane configuration and imaging logging data, the diabase intrusion in Zhanhua Sag is formed by tholeiite magma emplacing in Shahejie formation stratum on the rift tension background Lower Tertiary in North China. The diabase intrusion of Luo151 is composed possibly of three periods magma emplacement. There is serious anisotropy in the diabase reservoirs of Luo151 in Zhanhua Sag. Fracture is primary reservoir space, which dominated by tensile fracture in high obliquity, and the fracture zones are mainly developed round joint belt of igneous rock and wall rock and position of terrane thickness changing rapidly. The generation materials of the reservoirs in Luo151 igneous oil pools consist of Intergranular micropore hornfels, condensate blowhole-solution void diabase condensate edge, the edge and center of the condensate seam diabase, of which are divided into horizontal, vertical and reticulated cracks according fracture occurrence. Based on the above research, a conceptual model of igneous rock reservoir is generated, which is vertically divided into 4 belts and horizontally 3 areas. It is built for the first time that classification evaluation pattern of igneous rock reservoir in this area, and 3 key wells are evaluated. The diabase construction is divided into grammite hornfels micropore type and diabase porous-fracture type reservoirs. The heavy mudstone layers in Third Member of Shahejie formation (Es3) provide favorable hydrocarbon source rock and cap formation, diabase and hornfels belts serve as reservoirs, faults and microcracks in the wall rocks as type pathways for oil and gas migration. The time of diabase invasion was about in the later deposition period of Dongying Formation and the middle of that of Guantao Formation, the oil generated from oil source rock of Es3 in the period of the Minghuazhen formation and is earlier more than the period of diabase oil trap and porous space forming. Based on geological and seismic data, the horizon of igneous rocks is demarcated accurately by using VSP and synthetic seismogram, and the shape distribution and continuity of igneous rocks are determined by using cross-hole seismic technology. The reservoir capability is predicted by using logging constraining inversion and neural network technology. An integrated method to predict igneous rock oil and gas pool is formed. The study is appraised by using development data. The result show the reservoir conceptual model can guide the exploration and development of oil pool, and the integrated method yielded marked results in the production.