UASB反应器处理维生素C生产废水研究

维生素C生产废水有机物浓度高、成分复杂、排放量大，是一种亟待处理的典型工业废水。本研究分别采用实验室规模和中试规模的升流式厌氧颗粒污泥床反应器（UASB）对该制药工业废水的厌氧生物处理工艺进行了较为深入的研究。同时采用两种不依赖于纯培养的分子生物学手段—变性梯度凝胶电泳（DGGE）和扩增核糖体DNA限制性分析（ARDRA）技术揭示了UASB反应器不同运行阶段污泥中微生物群落多样性组成及变化。此外，首次研究了零价铁（Fe0）在厌氧消化过程中对反应器运行及微生物群落结构的影响。 采用城市污水处理厂厌氧消化池絮状污泥和处理啤酒废水的颗粒污泥混合接种，小试中温（35±1℃）UASB反应器在其运行的第65天启动成功。反应器稳定运行阶段，在进水COD浓度为9000mg/L、水力停留时间为12h、容积负荷为13.6 kgCOD/m3.d条件下，其COD去除率稳定在85~90%之间，沼气产率达到4.5 m3/m3.d，沼气甲烷含量平均为72%。中试UASB反应器的接种污泥为厌氧消化污泥，其启动时间相对较长，为90天。在稳定运行期，反应器的进水COD浓度为8000~10000mg/L，水力停留时间和容积负荷分别保持在12~16h和10.6~14.2 kgCOD/m3.d范围，该阶段反应器的平均COD去除率稳定在85%左右，沼气产率平均为5.2m3/m3.d，沼气中甲烷含量为69%。上述结果表明中温UASB工艺用于维生素C生产废水处理是高效、可行的。 与对照反应器相比，添加Fe0的小试UASB反应器的COD去除率和沼气产量分别提高了6.5%和10.2%。同时，磷酸盐平均去除率为79%，比对照提高了64%，目前尚未见类似研究报道。在中试规模的UASB反应器中补充一定量的Fe0可缩短反应器启动时间，促进颗粒污泥的形成，该结果可能具有重要的应用价值。培养试验进一步表明，Fe0可以作为产甲烷菌还原CO2生成甲烷的电子供体。培养实验还表明，当系统中存在硝酸盐（0.40 mM）和硫酸盐（0.26 mM）时，Fe0促产甲烷过程受到一定程度的抑制。 采用细菌通用引物968F/1401R和341F/907R获得的PCR-DGGE指纹图谱均表明UASB反应器不同运行阶段细菌种群结构变化明显。小试和中试稳定期污泥的微生物多样性均高于各自初始接种污泥。产甲烷菌通用引物340F/519R的PCR-DGGE结果显示，虽然接种污泥中产甲烷菌的丰富度系数略低于稳定期，但总体而言，反应器运行期间产甲烷菌的种群组成相对稳定。 通过构建不同处理和不同运行阶段污泥样品的16S rRNA基因文库并对克隆基因进行限制性内切酶消化、测序分析。结果表明，稳定期两个反应器微生物群落结构相似，但与各自接种污泥差异明显。小试UASB反应器接种污泥中细菌的优势菌群分别为变形菌纲的δ亚纲（28.7%）和β亚纲（17.4%），至稳定运行期则演替为革兰氏阳性低GC菌群（21.9%）和变形菌纲的δ亚纲（14.0%）。中试反应器接种污泥Green non-sulfer bacteria（25.9%）和变形菌纲的δ亚纲（16.4%）类群占优势，而稳定期Green non-sulfer bacteria类群（17.9%）、革兰氏阳性低GC菌群（16.2%）和变形菌纲的δ亚纲（15.4%）为优势菌群。 产甲烷菌的优势克隆为SRJ 230、SRJ 26和SRJ 583，前两者分别与Methanosaeta concilii和未培养的Methanobacteria-like克隆Gran7M4的同源性达到97%和98%，后者与Methanomethylovorans. sp同源性为99%。接种污泥中上述类群占总克隆数量的比例较低。小试、中试接种污泥中产甲烷菌分别占7.8%和3.0%，但稳定运行期，该比例明显增加，分别达到21.9%和18.8%。上述结果表明启动期与稳定期污泥产甲烷菌种群组成相对稳定，但各类群数量明显增加。 添加Fe0的UASB反应器稳定运行期污泥中产甲烷菌比例（31.2%）高于对照反应器（24.2%）, 革兰氏阳性低GC类群、变形菌纲的δ亚纲比例差异不明显，而变形菌纲β亚纲（6.0%）和Green non-sulfer bacteria（9.2%）的比例均分别低于对照反应器（13.1%和17.1%）。该结果表明，添加Fe0使反应器内微生物群落多样性发生了显著变化。 此外，在添加Fe0的UASB反应器中检测到特异性的克隆SRJ 341和SRJ 320，两者分别同磷酸盐去除和铁氧化有关的克隆子Orbal D41和Clone195的序列相似性达95%和96%。这两个类群可能分别与磷酸盐去除及铁促产甲烷作用密切相关。这一结果尚未见报道。

C离子束诱变产生甜高粱汁酒精酵母高产菌株的研究

利用100MeV/uC离子束对高产酒精酵母菌株进行了辐照诱变的研究。采用红四氮唑作为筛选指示剂,得到了5株产酒能力有所提高的突变酵母菌。利用甜高粱汁的发酵结果表明,T4突变菌株的产酒精能力比原始出发菌株提高了18.6%,且发酵液中的残糖含量也有所降低。随后对T4菌株在甜高粱汁中的最适宜发酵条件做了初步探索,结果表明:最适发酵温度和pH值分别为30℃和4.5。通过10l发酵罐的验证试验表明:在同样发酵条件下,T4菌株的发酵率和产酒精能力都比原始出发菌株提高了12%。

Single-electron capture in keV Ar15+...18++He collisions

Single-electron capture in 14 keV q(-1) Ar15+...18++He collisions is investigated both experimentally and theoretically. Partial cross sections and projectile scattering angle dependencies have been deduced from the target ion recoil momenta measured by the COLTRIMS technique. The comparison with close-coupling results obtained from a two-centre extension of the basis generator method yields good overall agreement, demonstrating the applicability of close-coupling calculations to collision systems involving highly charged ions in charge states up to 18+.

Investigation of PL properties of C-doped SiO2/Si samples after high energy Pb ion irradiation

Amorphous SiO2 thin films with about 400-500 nm in thickness were thermally grown on single crystalline silicon. These SiO2/Si samples were firstly implanted at room temperature (RT) with 100 keV carbon ions to 2.0 x 10(17),5.0 X 10(17) or 1.2 x 10(18) ions/cm(2), then irradiated at RT by 853 MeV Pb ions to 5.0 x 10(11), 1.0 X.10(12) 2.0 x 10(12) or 5.0 x 10(12) ions/cm(2), respectively. The variation of photoluminescence (PL) properties of these samples was analyzed at RT using a fluorescent spectroscopy. The obtained results showed that Pb-ion irradiations led to significant changes of the PL properties of the carbon ion implanted SiO2 films. For examples, 5.0 x 10(12) Pb-ions/cm(2) irradiation produced huge blue and green light-emitters in 2.0 x 10(17) C-ions/cm(2) implanted samples, which resulted in the appearance of two intense PL peaks at about 2.64 and 2.19 eV. For 5.0 x 10(17) carbon-ions/cm(2) implanted samples, 2.0 x 10(12) Pb-ions/cm(2) irradiation could induce the formation of a strong and wide violet band at about 2.90 eV, whereas 5.0 x 10(12) Pb-ionS/cm(2) irradiation could,create double peaks of light emissions at about 2.23 and 2.83 eV. There is no observable PL peak in the 1.2 x 10(18) carbon-ions/cm(2) implanted samples whether it was irradiated with Pb ions or not. All these results implied that special light emitters could be achieved by using proper ion implantation and irradiation conditions, and it will be very useful for the synthesis of new type Of SiO2-based light-emission materials.

Production cross-section of Ra-230 in the reaction of 60 MeV/u O-18 ions with U-238

A thick natural uranium target was bombarded with a 60 MeV/u O-18 beam. The neutron-rich isotope Ra-230 as the target residue was produced through the multinucleon transfer reaction (U-238-4p-4n). The barium and radium fraction as BaCl2 precipitate were radiochemically separated first from the mixture of uranium and reaction products. Then, the radium fraction was separated from BaCl2 precipitate by using cation exchange technique. The gamma-ray spectra of the Ra fraction were measured using an HPGe detector. The production cross sections of Ra-230 were obtained by a combination of the radiochemical separation technique and off-line gamma-ray spectroscopy. The cross section of Ra-230 has been determined to be 66 +/- 20 mu b.

Experimental study of the two-proton correlated emission from the excited states of Ne-17,Ne-18 and S-28,S-29

A series of experiments have been performed by complete kinematics measurements to study two-proton (2p) correlated emission from the excited states of Ne-17,Ne-18 and S-28,S-29 via the Coulomb excitation by bombarding on Au-197 target. 2p and residua coincident events were picked Out under strict conditions. Visible p-p correlations were observed. It is shown that 2p can be emitted from the high-lying excited states. 2p halo may lead to 2p emission with large spectroscopy factor for the states close to or beyond the threshold.

~(14)C-菲在营养液-火山石-小麦有控系统中的迁移和转化

利用放射性同位素示踪技术研究了１４Ｃ标记菲在有控系统中的迁移转化．结果表明，１４Ｃ菲在有控系统中降解较快，施入药品２４ｄ后仅有０．３２％的１４Ｃ－菲存留在植物、营养液和火山石中．植物吸收的１４Ｃ放射性大部分被结合到植物组织中，其它１４Ｃ主要以菲的极性代谢物形态存在．

Effects of treatment in different atmosphere on Pt3Sn/C electrocatalysts for ethanol electro-oxidation

Pt3Sn/C catalyst was prepared by a modified polyol process and treated in air, H-2/Ar, and Ar atmosphere, respectively. XRD analyses indicate that all of these catalysts have face-centered cubic (fcc) crystal structure. Temperature-programmed reduction (TPR) experiments show that more Sn exists in zero-valence in the Ar-treated PtSn catalyst than in the others. Cyclic voltammetry (CV), chronoamperometry (CA) experiments, and the performance tests of direct ethanol fuel cell (DEFC) indicate that the catalytic activity of PtSn/C for ethanol oxidation was affected significantly by the chemical state of Sn in catalyst particles. The as-prepared PtSn/C gives the higher power density, while Ar-treated PtSn/C shows the lower cell performance. It seems that the multivalence Sn rather than the zero-valence Sn in the PtSn catalyst is the favorable form for ethanol oxidation. Energy dispersion X-ray analysis (EDX) of the PtSn/C-as prepared and PtSn/C (after stability test) shows the active species (platinum, tin, and oxygen) composition changed to a different extent. Further attempt to improve the catalyst stability is needed.

保护性耕作对土壤线虫c-p类群及功能团的影响

以辽宁彰武县保护性耕作示范推广基地土壤为研究对象,通过实地调查和取样分析,对比研究了传统犁耕和6a保护性耕作(免耕秸秆覆盖)条件下的土壤线虫c-p(colonizer-persister)类群及功能团,为评价保护性耕作的土壤生态效应提供理论依据。研究发现,与犁耕相比,保护性耕作显著增加了土壤线虫各c-p类群及绝大多数功能团的多度,但显著减少了Ba4和Om5功能团多度。此外,保护性耕作还改变了土壤线虫生活史和功能团的结构特征:在大部分研究土层,c-p1和c-p2线虫的相对多度显著提高,而c-p3、c-p4以及c-p3-5类群显著降低;Ba1、Ba2、Ba3、Fu4和H5功能团的相对多度显著提高,而Ba4、H3和Om5的相对多度显著降低,Fu2、H2和Om4相对多度的变化较复杂,在表土层表现为显著抑制,在15~30cm土层则为促进作用。土壤线虫c-p类群和功能团的多度及结构特征可能适合作为评价保护性耕作对土壤质量影响的生物学指标。

维生素C“二步发酵法”第二步发酵混合菌关系的研究

维生素Ｃ“二步发酵法”第二步发酵混合菌关系的研究马成新，杨凤玫，焦鹏，薛德林，王书锦（中国科学院沈阳应用生态研究所，１１００１５）维生素Ｃ作为一种重要的医药产品，不但用于治疗多种疾病，而且已被广泛用于食品、化妆品、饲料产品中，随着维生素Ｃ应用范围的增...

High-pressure sintering the novel light (W0.25Al0.75)C hard material without binder phase

A novel hard material of (W0.25Al75)C has been successfully prepared by the high-pressure sintering process without the addition of any binder phase. The high-pressure is a suitable and powerful technique for sintering the binderless hard material, the relative density of the hard material can reach 99.6% under high-pressure sintering. The density of the novel light hard material is only 6.2371 g cm(-3), which is much lighter than the normal hard material. The hardness of the light hard material can reach 18.89 GPa even the aluminum content get the astonished 75%.