Characterization of recombination centres in n-type Hg1-xCdxTe

The defect levels in Hg1-xCdxTe P+N junction photodiodes (x = 0.4) were first studied using deep-level transient spectroscopy. Two electron traps, E(1)(0.06) and E(2)(0.15), and two hole traps, H-1(0.075) and H-2(0.29), were obtained, Characteristic parameters-the minority lifetime of the devices and the dynamic resistance-area product at zero bias-are estimated according to these levels. Results show that these two minority levels may be important in controlling lifetime. We have studied the recombination mechanism of the hole trap H-2(0.29) further. It has a large activation energy and satisfies the formula sigma(T) = sigma(x) exp(-E(F)/E(T)). This reflects the fact that its recombination mechanism is multiphonon nonradiative recombination, which is rarely reported in narrow-bandgap materials.

Boron-doped silicon film as a recombination layer in the tunnel junction of a tandem solar cell

Boron-doped hydrogenated silicon films with different gaseous doping ratios (B_2H_6/SiH_4) were deposited in a plasma-enhanced chemical vapor deposition (PECVD) system. The microstructure of the films was investigated by atomic force microscopy (AFM) and Raman scattering spectroscopy. The electrical properties of the films were characterized by their room temperature electrical conductivity (σ) and the activation energy (E_a). The results show that with an increasing gaseous doping ratio, the silicon films transfer from a microcrystalline to an amorphous phase, and corresponding changes in the electrical properties were observed. The thin boron-doped silicon layers were fabricated as recombination layers in tunnel junctions. The measurements of the Ⅰ-Ⅴ characteristics and the transparency spectra of the junctions indicate that the best gaseous doping ratio of the recombination layer is 0.04, and the film deposited under that condition is amorphous silicon with a small amount of crystallites embedded in it. The junction with such a recombination layer has a small resistance, a nearly ohmic contact, and a negligible optical absorption.

Effects of Cu-Wire Surface Fluctuations on Early Failures

Different chemical mechanical polishing （CMP） slurries are used to obtain single-damascene Cu-wires with different surface fluctuations as well as pre-existing surface-defects in wires with rougher surfaces. The presence of such pre-existing defects strongly increases the rate of early failures to almost 100%, reduces electromigration lifetime rapidly to the level of early failures, and changes the multimodal failure distribution into monomodal. The activation energy （0. 74±0.02eV） for the failure mechanism associated with these pre-existing defects confirms a dominant surface diffusion. It shows how a weakest link approximation analysis can he applied to a single wire by dividing the wire into relevant segments and assigning different failure mechanisms to the various segments. The analysis confirms that, although surface-defects are not the fastest early failure mechanism, the ten times higher surface-defectdensity in the rougher wires is responsible for the observed high early-failure rate and unreliable performance.

Photoluminescence measurements on erbium-doped silicon

Erbium-implanted silicones were treated by lamp-heating rapid thermal annealing (RTA). Two types of erbium-related photoluminescence spectra appear under different anneal temperatures. 750 degrees C annealing optimizes the luminescence intensity, which does not change with anneal time. Exciton-mediated energy transfer model in erbium-doped silicon was presented. The emission intensity is related to optical active erbium concentration, lifetime of excited Er3+ ion and spontaneous emission time. The thermal quenching of the erbium luminescence in Si is caused by thermal ionization of erbium-bound exciton complex and nonradiative energy backtransfer processes, which correspond to the activation energy of 6.6 meV and 47.4 meV respectively.

有机质谱裂解规律及智能解析方法研究

本学位论文分为四个部分，第一部分报道了用串联质谱快速分析合成药物中的微量杂质成分以及分析中药材中的化学成分。第二部分报道了通过质谱和串联质谱发现并合成新型的PdPincer 催化剂，同时对其活性进行测试。第三部分为串联质谱自动解析软件的设计及应用。第四部分概述了应用在质谱中的各种碎裂方式。 第一部分首先总结了5-溴粉防己碱及其类似物的裂解规律，并以此为根据推测出2 个微量杂质的结构。随后针对无患子（Sapindus mukurossi Gatren.）中的皂苷成分，由ESI-QTOF 得到各个皂苷成份的高分辨质量数据进而得到其分子式，然后利用ESI-IT 电喷雾串联质谱对无患子总皂苷中各皂苷成分的结构进行进一步的鉴定。进而以同样的方式，先通过ESI-QTOF 得到黄山药（Dioscoreapanthaica）总皂苷中各个组分化合物的分子式，然后对已有的薯蓣皂苷标准品做串联质谱分析，以得到该类化合物的裂解规律并给出解析该类化合物的流程图。在此利用计算化学的方法讨论了离子的丰度与裂解活化能之间的关系。然后应用APCI-MS/MS 方法探讨了四对同分异构体和几个已知的化合物，并最后用液质联用对其进行确认，同时还给出了4 个未知化合物的可能结构。 第二部分报道通过质谱和串联质谱发现并合成新型的PdPincer 催化剂，同时对其活性进行测试。钯催化的交联反应是有机合成中C-C 键形成的最有效的方法，且硫脲是一类对空气和水都稳定的化合物，因此我们设计并合成了一系列的硫脲钯催化剂并得到了很好的催化活性。我们在对其中一类环状双硫脲化合物进行质谱实验的时候，在正离子模式下发现了反常的[M.H]+，通过串联质谱进一步确定了它是一种新型的PdPincer 结构。我们将其合成出来并通过X-ray 衍射实验确定了它的结构。同时测定其催化活性并与未形成pincer 的类似物进行比较发现该类化合物具有较宽的底物适用性。 第三部分为串联质谱自动解析软件的设计及应用。通过前面两部分的启示，独立设计开发了AuMass（1.0）。其算法是：先通过查找特殊的碎片离子，中性丢失或碎片离子质量差来确定某类化合物的骨架结构，然后利用该类化合物的自动解析流程来对其周边取代基进行确认。通过它快速地对白芍中的化学成分进行解析，并对未知的化合物进行了推测。为了增加它的解析能力，我又对其它类型的化合物裂解规律进行总结，并给出了自动解析流程。实践证明该软件具有相当好的应用价值。 第四部分综述了应用在质谱上的各类母离子的碎裂技术。这里包括了碰撞诱导裂解（CID）、光诱导碎裂（LID）、电子捕获裂解/电子转移裂解（ECD/ETD）、红外多光子解离（IRMPD）、黑体辐射解离（BIRD）和PQD 裂解技术。 This dissertation consists of four chapters. The first chapter reports the rapidanalysis of trace impurities from synthetical medicine and analysis of the chemicalconstitutents from Chinese herb medicines. The second chapter elaborates the studieson the discorvery and synthesis of new type of Pd Pincer catalyst by using MS andtandem MS together with the testing of its catalyst activity. The third chapter dwellson the designation and development of automatic tandem mass spectrometry analysissoftware. The last chapter presents a review on the dissociation technique of massspectrometry. The first chapter reports the rapid analysis of trace impurities from synthesismedicine and analysis of the chemical constitutents from Chinese herb medicines. The fission mechanism of 5-bromotetrandrine was obtained by analysis of the dissociationpathways of major product, by using which the possible structure of the two traceimpurties was assumed. There are lots of saponins in Sapindus mukurossi. Except forthe good spumescence and decontamination，it possesses the bioactivity of antigenand antitch. First of all, the high resolution mass information was obtained by ESI-QTOF. Hence the possible molecular formulars were acquired too. Then weconducted the further detection of the structures of its saponins by using ESI-ITtechnology. In the same manner, first the molecular formulars of every constituentfrom Dioscorea panthaica in total saponins were obtained by ESI-QTOF, and thenacquired the fission mechanism of this type of compounds by tandem massexperiment on a series of known and available saponins. In the same time, theanalysis flowchart was concluded. Here the relationship between the ion intensity andthe corresponding dissiociation activation energy was studied by computer chemistry.Then the four pairs of isomers were differentiated by APCI-MS/MS, as well as thecharacterization of known and unknown compounds. The assumption was confirmed by HPLC-MS/MS. Among them the possible structures of four unknown saponinswas presented. The second part was discovery and synthesis of a new type of Pd pincer catalystby MS and tandem MS. The coupling reaction catalyzed by Pd is the most effectivemethod in C-C formation in organic synthesis. Apart from that, thiourea is type ofcompounds that are stable to atmosphere and moisture. Hence we designed a series ofPd thiourea catalysts. Some of them show the excellent catalyst activity. The abnormalparent ion [M.H]+ was founded in positive ESI mode when we conduct some massspectrometry experiments on the bicyclical thiourea Pd complex. The structure wasproposed by mass and tandem mass spectrometry. Because it was a new type of pincer,we want to test its catalyst activity. So the Pd pincer was synthesized and the detailstructure was obtained by x-ray experiment. It shows the more fitness in catalysis ofSuzuki reaction by comparison with the analogue. The third chapter dwells on the design and development of automatic tandemmass spectrometry analysis software. Inspired by the former two chapters, theAuMass (version 1.0) was developed. Its algorithm is: first check the diagnostic ion,diagnostic neutral loss or diagnostic ions mass intervals in database to find out whatthe analyst’s skeleton belongs to, then identify the peripheral functional group by thecorresponding analysis flowchart. The chemical constituents of Paeonia lactiflorawere identified rapidly by using AuMass. To increase the analysis ability, the othertypes of compounds from Chinese herbs was concluded. Actually, the software isproven to have the much valuable application. The last chapter presented the review on the some kinds of fission technique ofmass spectrometry. It involves the collision induced dissociation (CID), laser induceddissociation (LID), electron capture dissociation/electron transfer dissociation(ECD/ETD), infrared multiple photons dissiociation, black body irraditiondissociation and PQD fission technique from Finnigan.

Charge-sensitive deep level transient spectroscopy of helium-ion-irradiated silicon, as-irradiated and after thermal annealing

Electrically active defects in the phosphor-doped single-crystal silicon, induced by helium-ion irradiation under thermal annealing, have been investigated. Isothermal charge-sensitive deep-level transient spectroscopy was employed to study the activation energy and capture cross-section of helium-induced defects in silicon samples. It was shown that the activation energy levels produced by helium-ion irradiation first increased with increasing annealing temperature, with the maximum value of the activation energy occurring at 873K, and reduced with further increase of the annealing temperature. The energy levels of defects in the samples annealed at 873 and 1073K are found to be located near the mid-forbidden energy gap level so that they can act as thermally stable carrier recombination centres.

Thermodynamic study of ibuprofen by adiabatic calorimetry and thermal analysis

Molar heat capacities of ibuprofen were precisely measured with a small sample precision automated adiabatic calorimeter over the temperature range from 80 to 400 K. The polynomial functions of C-p,C-m (J K-1 mol(-1)) versus T were established on the heat capacity measurements by means of the least fitting square method. The functions are as follows: for solid ibuprofen, at the temperature range of 79.105 K less than or equal to T less than or equal to 333.297 K, C-p,C-m = 144.27 + 77.046X + 3.5171X(2) + 10.925X(3) + 11.224X(4), where X = (T - 206.201)/127.096; for liquid ibuprofen, at the temperature range of 353.406 K less than or equal to T less than or equal to 378.785 K, C-p,C-m = 325.79 + 8.9696X - 1.6073X(2) - 1.5145 X-3, where X = (T - 366.095)/12.690. A fusion transition at T = 348.02 K was found from the C-p-T curve. The molar enthalpy and entropy of the fusion transition were determined to be 26.65 kJ mol(-1) and 76.58 J mol(-1) K-1, respectively. The thermodynamic functions on the base of the reference temperature of 298.15 K, (H-T - H-298.15) and (S-T - S-298.15), were derived. Thermal characteristic of ibuprofen was studied by thermo-gravimetric analysis (TG-DTG) and differential scanning calorimeter (DSC). The temperature of fusion, the molar enthalpy and entropy of fusion obtained by DSC were well consistent with those obtained by adiabatic calorimeter. The evaporation process of ibuprofen was investigated further by TG and DTG, and the activation energy of the evaporation process was determined to be 80.3 +/- 1.4 kJ mol(-1). (C) 2003 Elsevier B.V. All rights reserved.

Thermoluminescence characteristics of NaSr4(BO3)(3):Ce3+ under beta-ray irradiation

The thermoluminescence (TL) properties of Ce3+ doped NaSr4(BO3)(3) phosphor under the beta-ray irradiation were reported. The polycrystalline sample was synthesized by high temperature solid-state reaction. The TL glow curve of NaSr4(BO3)(3):Ce3+ phosphor was composed of only one peak. TL kinetic parameters of NaSr4(BO3)(3):Ce3+ were deduced by the peak shape method, the activation energy (E) was 0.590 eV and the frequency factor was 1.008x10(6) s(-1). TL dose response was linear in the range of measurement. The 3-dimensional (3D) TL emission spectrum was also recorded, the emission spectrum consisted of two bands located at 441 and 479 nm respectively, corresponding to the characteristic 4f(0)5d(1)-> F-2((5/2,7/2)) transitions of the Ce3+ ion. The fading behavior of the NaSr4(BO3)(3):Ce3+ phosphor over a period of 15 d was also studied.

Preparation and electrical properties of new oxide ion conductors Ce6-xDyxMoO15-delta (0.0 <= x <= 1.8)

Ce6-xDyxMoO15-delta (0.0 <= x <= 1.8) were synthesized by modified sol-gel method. Structural and electrical properties were investigated by means of X-ray diffraction (XRD), Raman, X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The XRD patterns showed that the materials were single phase with a cubic fluorite structure. Impedance spectroscopy measurement in the temperature range between 350 degrees C and 800 degrees C indicated a sharp increase in conductivity for the system containing small amount of Dy2O3. The Ce5.6Dy0.4MoO15-delta detected to be the best conducting phase with the highest conductivity (sigma(t) = 8.93 x 10(-3) S cm(-1)) is higher than that of Ce5.6Sm0.4MoO15-delta (sigma(t) = 2.93 x 10(-3) S cm(-1)) at 800 degrees C, and the corresponding activation energy of Ce5.6Dy0.4MoO15-delta (0.994 eV) is lower than that of Ce5.6Sm0.4MoO15-delta (1.002 eV).

Preparation and Electrical Properties of New Oxide Ion Conductors Ce6-xGdxMoO15-delta (0.0 <= x <= 1.8)

A series of oxide ion conductors Ce6-xGdxMoO15-delta (0.0 <= x <= 1.8) have been prepared by the sol-gel method. Their properties were characterized by differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), Raman, IR, X-ray photoelectron spectroscopy (XPS), and AC impedance spectroscopy. The XRD patterns showed that the materials were single phase with a cubic fluorite structure. The conductivity of Ce6-xGdxMoO15-delta increases as x increases and reaches the maximum at x = 0.15. The conductivity of Ce4.5Gd1.5MoO15-delta is sigma(t) = 3.6 x 10(-3) S/cm at 700 degrees C, which is higher than that of Ce4.5/6Gd1.5/6O2-delta (sigma(t) = 2.6 x 10(-3) S/cm), and the corresponding activation energy of Ce4.5Gd1.5MoO15-delta (0.92 eV) is lower than that of Ce4.5/6Gd1.5/6O2-delta (1.18 eV).

Synthesis and Electrical Properties of New Solid State Electrolyte Materials Ce6-xHoxMoO15-delta(0.0 <= x <= 1.2)

Ce6-xHoxMoO15-delta(0.0 <= x <= 1.2) was synthesized by modified sol-gel method and characterized by differential X-ray diffraction(XRD), Raman, and X-ray photoelectron spectroscopy(XPS) methods. The oxide ionic conductivity of the samples was investigated by AC impedance spectroscopy. It shows that all the samples are single phase with a cubic fluorite structure. The solid solution Ce6-xHoxMoO15-delta(x=0.6) was detected to be the best conducting phase with the highest conductivity(sigma(t)=1.05x10(-2) S/cm) at 800 degrees C and the lowest activation energy(E-a=1.09 eV). These properties suggest that this kind of material has a potential application in intermediate-low temperature solid oxide fuel cells.

Thermoluminescence studies of LiBa2B5O10 : RE3+ (RE = Dy, Tb and Tm)

LiBa2B5O10:RE3+ (RE = Dy, Tb and Tm) was synthesized by the method of high-temperature solid-state reaction and the thermoluminescence (TL) properties of the samples under the irradiation of the gamma-ray were studied. The result showed that Dy3+ ion was the most efficient activator. When the concentration of Dy3+ was 2 mol%, LiBa2B5O10:Dy3+ exhibited a maximum TL output. The kinetic parameter of LiBa2B5O10:0.02Dy was estimated by the peak shape method, for which the average activation energy was 0.757 eV and the frequency factor was 1.50 x 10(7) s(-1). By the three-dimensional (3D) TL spectrum, the TL of the sample was contributed to the characteristic f-f transition of DY3+. The dose-response of LiBa2B5O10:0.02Dy to gamma-ray was linear in the range from 1 to 1000 mGy. In addition, the decay of the TL intensity of LiBa2B5O10:0.02Dy was also investigated.