Study on growth factors of intermetallic layer within hot-dipped 25% Al-Zn alloy coating on steel

25%Al-Zn alloy coating performs better than hot dip galvanized coating and 55%Al-Zn-Si coating with regard to general seawater corrosion protection. This study deals with the interfacial intermetallic layer's growth, which affects considerably the corrosion resistance and mechanical properties of 25%Al-Zn alloy coatings, by means of three-factor quadratic regressive orthogonal experiments, The regression equation shows that the intermetallic layer thickness decreases rapidly with increasing content of Si added to the Zn-Al alloy bath, increases with rise in bath temperature and prolonging dip time. The most effective factor that determined the thickness of intermetallic layer was the amount of Si added to Zn-Al alloy bath, while the effect of bath temperature and dip time on the thickness of intermetallic layer were not very obvious.

Effect of nano-TiO(2)on MP-25 resin

MP-25 resin is a chlorine-containing polymer widely used in coatings. The effects of two types of nano-TiO2 (P-25 and RM301 LP) on MP-25 were studied with saline immersion, UV irradiation, and electrochemical impedance spectroscopy. UV irradiation was evaluated in terms of gloss change and X-ray photoelectron spectroscopy (XPS). The results indicate that, compared to pigment R-930 TiO2, P-25 reduced the immersion resistance and accelerated UV aging of the MP-25 coating, whereas RM301 LP showed the opposite effects. XPS analysis showed that MP-25 resin degraded under UV irradiation via dechlorination and C-C bond breakage, similarly to poly(vinyl chloride), but RM301 LP could inhibit the aging of MP-25 to a certain extent. A skin effect of oxygen and chlorine was identified in MP-25 resin by XPS. RM301 LP could improve the impedance of the MP-25 coating because of its excellent fill capacity. Hence, rutile nano-TiO2 RM301 LP represents an excellent additive for MP-25 resin. (c) 2007 Wiley Periodicals, Inc.

压力和铁含量对铁方镁石(Mg1-xFex)O(x<=0.25)弹性常数影响的第一性原理研究

By first principle methods based on density functional theory (DFT),the equation of state(EOS) and elastic constants of both periclase and ferropericlase are calculated. The pressure and iron doping effects on the elastic constants of ferropericlase are investigated systematically. Firstly, we calculate the elastic constants of periclase and compare the obtained results with experimental data and other theoretical calculations, which shows a encouraging consistence and demonstrates the practicability of first-principle methods. Secondly, by adding iron into periclase crystal model, we build up ferropericlase with iron contents ranging from 0% to 25% mole percent. The corresponding elastic constants are calculated in a large pressure range(0~120GPa). Emphatically, the strong correlation of 3d electrons in transitional elements, such as iron, is difficult to treat in first-principle methods for a long time. The current solution is to make additional correction. During the initial stage of this study, the strong correlation of 3d electrons in iron is not considered, and we observed that addition of iron decreases the volume of ferropericlase, which is totally contradictory to the experimental data. By applying LDA+U approximation in order to solve the strongly correlated 3d electron of iron, we observed the expansion of volume by iron as expected. On the basis of the LDA+U approximation, the elastic constants of ferropericlase are calculated. After a detailed analysis of data obtained from theoretical calculations, we have reached the following conclusions:(1)pressure imposes positive effects on all elastic constants, and the degree of effects is C11>C12>C44. (2) Iron has no distinctive effects on C11 and C12, although some fluctuations are observed around 60GPa. However, iron has obvious softening effects on C44 The softening effects on C44 are intensified as pressure increases. Above the 100GPa, the effects increase greatly, even surpasses the pressure's positive effects in ferropericlase crystal models with iron mole percent of having 12.5%, 18.75% and 25% iron content. (3)As to the modulus deprived from elastic constants, iron has no effect on the adiabatic bulk module BS, only a little fluctuation around 60GPa. We find iron's softening effects on shear modulus G. (4)We find out that, compared with low iron content, elastic constants with iron content approaching 25mole% is consistently fluctuated，which may be caused by the limitations of the LDA+U approximation method itself. (5)We investigate the pressure and Fe doping effects on elastic anisotropy factor（A=(2C44+C12-C11)/C11） of ferropericlase and find out that iron contents will lower the critical isotropic pressure. At the same pressure, when the pressure is below the isotropic pressure, iron softens the anisotropy factor ; when pressure surpasses the isotropic pressure, iron increases the anisotropy factor.