Assemble of poly(aniline-co-o-aminobenzenesulfonic acid) three-dimensional tubal net-works onto ITO electrode and its application for the direct electrochemistry and electrocatalytic behavior of cytochrome c

Stable electroactive film of poly(aniline-co-o-aminobenzenesulfonic acid) three-dimensional tubal net-works was assembled on indium oxide glass (ITO) successfully, and the cytochrome c was immobilized on the matrix by the electrostatic interactions. The adsorbed cytochrome c showed a good electrochemical activity with a pair of well-defined redox waves in pH 6.2 phosphate buffer solution, and the adsorbed protein showed more faster electron transfer rate (12.9 s(-1)) on the net-works matrix than those of on inorganic porous or even nano-materials reported recently. The immobilized cytochrome c exhibited a good electrocatalytic activity and amperometric response (2 s) for the reduction of hydrogen peroxide (H2O2). The detection limit for H2O2 was 1.5 mu M, and the linear range was from 3 mu M to 1 mM. Poly(aniline-co-o-aminobenzenesulfonic acid) three-dimensional tubal net-works was proved to be a good matrix for protein immobilization and biosensor preparation.

Facile preparation of ZnTiO3 ceramic powders in sodium/potassium chloride melts

A facile molten salt synthesis route was developed to prepare ZnTiO3 ceramic powders with simple oxides ZnO and TiO2 using sodium and potassium chloride eutectic salts as flux. The role of calcination temperature and time and the amount of salt addition to ZnTiO3 formation was investigated by thermogravimetry-differential thermal analysis, X-ray diffraction and Fourier transformation-infrared spectroscopy measurements. Pure hexagonal phase of ZnTiO3 could be obtained from the mixture of the simple oxides and the chlorides (50 mol% KCl, 20 times to oxides in molar ratio) heating at 800 degrees C for 6 h. The scanning electron microscopy images revealed the products were hexagonal sheets of about 1-3 mu m size. Increasing the amount of salt aids in reducing the crystal sizes of final ceramic powders because of diluting the solution.

Fabrication of silver nanoparticles ring templated by plasmid DNA

Silver nanoparticles ring was successfully fabricated by electrostatic assembling 4-aminothiophenol (4-ATP) capped silver nanoparticles on predefined extended circular plasmid pBR322 DNA. The silver nanoparticles ring which was about 1.5 mu m in length, and about 2.2 nm in height can be obtained by adjusting the reaction time. The normal Raman scattering spectra reveal that the 4-ATP has contacted with the silver nanoparticles by forming a strong Ag-S bond. The AFM data show that the assembly of 4-ATP capped silver nanoparticles on DNA is ordered.

Deformation mechanism of polystyrene toughened with sub-micrometer monodisperse rubber particles

Core-shell polybutadiene-graft-polystyrene (PB-g-PS) rubber particles with different ratios of polybutadiene to polystyrene were prepared by emulsion polymerization through grafting styrene onto polybutadiene latex. The weight ratio of polybutadiene to polystyrene ranged from 50/50 to 90/10. These core-shell rubber particles were then blended with polystyrene to prepare PS/PB-g-PS blends with a constant rubber content of 20 wt%. PB-g-PS particles with a lower PB/PS ratio (<= 570/30) form a homogeneous dispersion in the polystyrene matrix, and the Izod notched impact strength of these blends is higher than that of commercial high-impact polystyrene (HIPS). It is generally accepted that polystyrene can only be toughened effectively by 1-3 mu m rubber particles through a toughening mechanism of multiple crazings. However, the experimental results show that polystyrene can actually be toughened by monodisperse sub-micrometer rubber particles. Scanning electron micrographs of the fracture surface and stress-whitening zone of blends with a PB/PS ratio of 70/30 in PB-g-PS copolymer reveal a novel toughening mechanism of modified polystyrene, which may be shear yielding of the matrix, promoted by cavitation.

Compatibilization of PP/EPDM blends by grafting acrylic acid to polypropylene and epoxidizing the diene in EPDM

In this article, ethylene-propylene-diene-rubber (EPDM) was epoxidized with an in situ formed performic acid to prepare epoxided EPDM (eEPDM). The eEPDM together with the introduction of PP-g-AA was used to compatibilize PP/EPDM blends in a Haake mixer. FTIR results showed that the EPDM had been epoxidized. The reaction between epoxy groups in the eEPDM and carboxylic acid groups in PP-g-AA had taken place, and PP-g-EPDM copolymers were formed in situ. Torque test results showed that the actual temperature and torque values for the compatibilized blends were higher than that of the uncompatibilized blends. Scanning electron microscopy (SEM) observation showed that the dispersed phase domain size of compatibilized blends and the uncompatibilized blends were 0.5 and 1.5 mu m, respectively. The eEPDM together with the introduction of PP-g-AA could compatibilize PP/EPDM blends effectively. Notched Izod impact tests showed that the formation of PP-g-EPDM copolymer improved the impact strength and yielded a tougher PP blend.

Synthesis and characterization of ferrocene-terminated ruthenium phenylacetylide complexes with alligator clips

Ferrocene-terminated trans/Ru(dppm)(2) (dppm=Ph2PCH2PPh2)-contained molecular wires with alligator clips were prepared. They are suitable for self-assembly on gold electrode to investigate the influence of metal incorporation on the electron transportation property of the molecular wires.

Gd3+ -> Eu2+ energy transfer in BaLiF3 : Eu, Gd

Photoluminescence characteristics and the energy transfer between Gd3+ and Eu2+ in BaLiF3,, matrix have been investigated. A series of concentrations of Gd3+ ion with a fixed Eu2+ concentration doped in BaLiF3 : Gd3+, Eu2+ has been studied. When the doping concentration for Gd3+ was 0.3%,, the system reached the highest energy transfer efficiency. Due to the competitive absorption for the Gd3+ and the Eu2+ ions in BaLiF3 : Gd3+ : Eu2+, when the doping concentration for Gd3+ ion exceeded 0.3 Vo, the continuously increasing concentration of Gd3+ ions caused the competitive absorption ratio for Gd3+ increasing and the emission intensity of Eu2+ decreasing. The energy transfer processes were discussed, while the transfer probability was calculated to be 1.35 X 10(5) s(-1).

用辐射方法制备PCL/玻璃纤维布和PCL/碳纤维布复合材料以及它们的生物降解性研究

观察了聚已内酯 (PCL) /玻璃纤维布和PCL/碳纤维布的机械性能的变化 ,通过对辐射交联的方法制备出了可生物降解聚合物涂覆纤维布复合材料。结果表明 ,γ辐射提高了复合材料的机械性能 ,这是由于所涂覆聚合物交联所产生的凝胶所致。在过冷态下通过γ射线照射 2 70kGy的PCL/玻璃纤维布复合材料的弯曲强度是未辐照样品的 1.5倍 ,弯曲模量提高到 1.35倍。通过酶降解试验和土埋法降解实验的研究 ,可以观察到降解导致了样品的失重。在酶降解试验中2 3h后 ,对于未交联材料涂覆的PCL完全降解掉 ,而交联样品中的PCL有 5 4%的失重发生。同样 ,在土埋法降解实验中 ,交联和未交联样品在一定的土埋时间后 ,也产生了样品的失重。未交联样品的失重率大于交联样品 ,这是由于交联样品所含有的交联网络结构阻碍它的降解。

Renewable-surface amperometric nitrite sensor based on sol-gel-derived silicomolybdate-methylsilicate-graphite composite material

A new type of silicomolybdate-methylsilicate-graphite composite material was prepared by the sol-gel technique and used for the fabrication of an amperometric nitrite sensor. The silicomolybdic anion acts as a catalyst, the graphite powder ensures conductivity by percolation, the silicate provides a rigid porous backbone and the methyl groups endow hydrophobicity and thus limit the wetting section of the modified electrode. Cyclic voltammetry, square-wave voltammetry and chronoamperometry were employed to characterize the sensor. The amperometric nitrite sensor exhibited a series of good properties: high sensitivity (1.771 mu A mmol(-1) dm(3)), a short response time (7 s), remarkable long-term stability and especially reproducibility of surface renewal in the event of electrode surface fouling.

End-column electrochemical detection for aromatic amines with high performance capillary electrophoresis

Electrochemical detection of five species of aromatic amines at a carbon fiber microdisk electrode after separation by capillary electrophoresis is described. Under the optimum conditions, the detection limit for 3,4-dihydroxybenzylamine, N,N-dimethylaniline, p-phenylenediamine, p-aminophenol and aniline sulfate was 0.9, 0.03, 0.075, 1.2 and 0.15 mu M (S/N = 3), respectively. The linear response range was 5-1000, 0.1-500, 0.5-500, 5-500 and 1-200 mu M, respectively The effect of the electrode position and buffer pH on the detection was also studied. This method is very simple, sensitive and stable for the detection of these compounds.

Self-gelatinizable copolymer immobilized glucose biosensor based on Prussian Blue modified graphite electrode

A novel poly(vinyl alcohol) grafting 4-vinylpyridine self-gelatinizable copolymer was adapted to immobilize glucose oxidase. The reduction of hydrogen peroxide (H2O2) was detected at a Prussian Blue (PB) modified graphite electrode. A stable and sensitive glucose amperometric biosensor is described. The copolymer is a good biocompatible polymer in which the glucose oxidase retains high activity. Moreover, the copolymer can adhere firmly to the inorganic PB membrane. The sensor showed an apparent Michaelis-Menten constant of 18 +/- 0.2 mM and a maximum current density of 1.14 mu A cm(-2) mM(-1). The linear range is from 5 mu M to 4.5 mM glucose and the detection limit is 0.5. mu M glucose. The catalytic efficiency of PB for the reduction of H2O2 is higher than that for the oxidation of H2O2. Glucose concentrations in serum samples from healthy persons and diabetic patients were determined using the sensor. The results compared well with those provided by the hospital using a spectroscopy method.

Iron(II)-8-quinolinol/MCM-41-catalyzed phenol hydroxylation and reaction mechanism

Iron(II)-8-quinolino/MCM-41 is prepared. Its catalysis is studied in phenol hydroxylation using H2O2 (30%) as oxidant. The experiment shows that Iron(II)-8-quinolinol/MCM-41 has good catalytic activity and desired stability. Based on cyclic voltammetry, ESR, and UV-visible spectra studies of iron(II)-8-quinolinol complex in liquid phase, a radical substitution mechanism is proposed and used to demonstrate the experimental facts clearly. (C) 1997 Academic Press.

Pd(Ⅱ)/BQ催化环己烯氧化合成环己酮的反应机理

在乙腈的酸性水溶液中，考察了Pd（OAc）2、Pd（NO3）2、PdCl2和苯醌（BQ）组成的催化体系在环己烯氧化合成环己酮反应中的催化活性，探索了酸度对Pd（OAC）2／BQ催化活性的影响．结果表明，Pd（OAc）2／BQ和Pd（NO3）2／BQ对环乙烯氧化合成环己酮显示了较高的催化活性，而PdCl2／BQ的活性则较低，无水和无酸存在的溶液中，Pd（OAc）2／BQ对环己烯氧化未显现任何催化活性．并用紫外可见光谱（UV－Vis）、循环伏安法考察了该催化体系的作用机理

Synthesis of lanthanide-alkylaluminium bimetallic complexes and studies on their catalytic activities for polymerization of some polar monomers

Three new lanthanide (Ln)-alkylaluminium (Al) bimetallic complexes with the formula [(mu-CF3CO2)(2)Ln(mu-CF3CHO2)AIR(2) . 2THF](2) (Ln = Nd, Y, R=i-C4H9 (i-Bu); Ln=Eu, R=C2H5(Et); THF=tetrahydrofuran) were synthesized by the reaction of Ln(CF,CO,), (Ln=Nd, Y) with HAI (i-Bu)(2) and of Eu(CF3CO2)(3) with AlEt(3), respectively. Their crystal structures were determined by X-ray diffraction at 233 K. [(mu-CF3CO2)(2)Nd (mu-CF3CHO2)Al(i-Bu)(2) . 2THF](2) (Nd-Al) and [(mu-CF3CO2)(2)Y(mu-CF3CHO2)Al(i-Bu)(2) . 2THF](2) (Y-Al) are isomorphous and crystallize in space group with a=12.441(3) Angstrom [12.347(5) Angstrom for Y-Al], b=12.832(3) Angstrom [12.832(4) Angstrom], c=11.334(3) Angstrom [11.292(8) Angstrom], alpha=104.93 (2)degrees [104.45(4)degrees], beta=98.47(2)degrees [98.81(4)degrees], gamma=64.60(2)degrees [64.30(3)degrees], R=0.519 [0.113], R(w)=0.0532 [0.110], Z=1 and [(mu-CF3CO2)(2)Eu(CF3CHO2)AlEt(2) . 2THF](2)(Eu-Al) in space group P2(1)/n with a=11.913(6) Angstrom, b=14.051(9) Angstrom, c=17.920(9) Angstrom, alpha=101.88(11)degrees, beta=gamma=90 degrees, R=0.0509, R(w)=0.0471 and Z=2. The six CF3CO2- (including CF3CHO2-) of each complex, among which pairs are equivalent, coordinated to Ln and Al in three patterns: (A) the two oxygen atoms in one of the three CF3CO2- type coordinated to two different Ln; (B) the two oxygen atoms in the second of CF3CO2- type coordinated to Ln and Al, respectively; (C) one of the two oxygen atoms in the third CF3CO2- type bidentately coordinated to two Ln and another oxygen coordinated to Al and one of the two Ln, respectively. Unlike types A and B, in type C the carboxyl carbon with a hydrogen atom bonded to it was found to appear as an sp(3)-hybridized configuration rather than an sp(2)-one. 1D and 2D NMR results further confirmed the existence of such a disproportionated CF3CHO2- ligand. Methyl methacrylate (MMA) and epichlorohydrin (ECH) could be polymerized by Y-Al or Eu-Al as a single-component catalyst and highly syndiotactic poly(MMA) was obtained. THF could also be polymerized by Y-Al in the presence of a small amount of ECH.

酞侧基聚芳醚酮的应力松弛与屈服行为的模型解析

根据不同温度下酞侧基聚芳醚酮（ＰＥＫ—Ｃ）的应力松弛曲线及时－温等效原理，得到了ＰＥＫ—Ｃ在任意参考温度下的总曲线．应用Ｋｏｈｌｒａｕｓｃｈ—Ｗｉｌｌｉａｍｓ－Ｗａｔｔｓ（ＫＷＷ）模型定量解释了应力松弛现象的温度依赖性，并通过ＫＷＷ模型建立了应力松弛现象与屈服行为间的相关性．