CURE AND IONIC-CONDUCTIVITY OF A 2-COMPONENT EPOXY NETWORK POLYMER ELECTROLYTE

In order to raise the room temperature ionic conductivity and improve the mechanical strength of a PEO-based polymer electrolyte, a non-crystalline two-component epoxy network was synthesized by curing diglycidyl ether of polyethylene glycol (DGEPEG) with triglycidyl ether of glycerol (TGEG) in the presence of LiClO4 salt, which acts in this system as both a ring opening catalyst and a source of ionic carrier. The structure of the precursors, the curing process and the cured films have been characterized by C-13 NMR, IR, DSC and ionic conductivity measurement techniques. The electrolyte system exhibits an ionic conductivity as high as similar to 10(-5) S/cm at 25 degrees C and is mechanically self-supportable. The dependence of ionic conductivity was investigated as a function of temperature, salt content, MW of PEG segment in DGEPEG and the proportion of DGEPEG in DGEPEG/TGEG ratio.

Study on comblike polymer electrolyte

New comblike polymers(CP) have been synthesized by reacting monomethyl ether of polyethylene glycol(PEGME) with poly(methyl vinyl ether-alt-maleic anhydride)(MA) and endcapping the residual carboxylic acid with methanol. Butanone was selected as a solvent for the esterification reaction in order to obtain a completely soluble product. They were characterized by IR, C-13 NMR and elemental analysis.

Study on new comb polymer electrolyte(III)

A new solid polymer electrolyte has been prepared using NaClO4 and a comb-branch polymer with oligo(ethylene oxide) side chains. The thermal and ionic conductive properties of the electrolytes were investigated. The profile of conductivity at various temperatures follows the VTF plots.

Study on a new comb polymer electrolyte(II)

A comb polymer(CP350) with oligo-oxyethlene side chains was prepared from methyl vinyl ether/maleic anhydride copolymer. Homogeneous amorphous polymer electrolyte were made from the comb polymer and LiCF3SO3 by solvent casting from acetone, and their conductivities were measured as a function of temperature and salt concentration. Maximum conductivity close I to 5.08 x 10(-5)S/cm was achieved at room temperature at [Li]/[EO] ratio of about 0.12.

2-COMPONENT EPOXY NETWORK-LICLO4 POLYMER ELECTROLYTE

An epoxy network-LiClO4 electrolyte system was prepared from diglycidyl ether of polyethylene glycol and triglycidyl ether of glycerol, cured in the presence of LiClO4 only. Various techniques were used to characterize the chemical structure of the precursors and the correlation between the viscoelasticity and conductivity of the cured films was examined.

THE IMPEDANCE STUDY OF MODIFIED PEO POLYMER ELECTROLYTE

The ultra-thin modified PEO (polyethylene oxide)-LiClO4 polymer electrolyte film (50-mu-m) was obtained by solution-casting technique. Impedance spectra were taken on the cells consisting of above PEO film electrolyte and ion-blocking or nonblocking electrodes. The ambient conductivity as high as 1.33 X 10(-4)S cm-1 could be achieved for PEO electrolyte modified by the crosslinking. It was shown that the resistance at the interface between solid polymer electrolyte and lithium electrode is growing with increasing the storage time. At high temperature, as 96-degrees-C, the ionic transport is clearly controlled by diffusion.

Investigation of platinum utilization and morphology in catalyst layer of polymer electrolyte fuel cells

Platinum utilization in the gas-diffusion catalyst layer and thin-film catalyst layer is investigated. The morphology of PTFE and Nafion in a simulated catalyst layer is examined by scanning electronmicroscopy (SEM) and transmission electron microscopy (TEM). The results show that the platinum utilization of the thin-film catalyst layer containing only Pt/C and Nafion is 45.4%. The low utilization is attributed to the fact that the electron conduction of many catalyst particles is impaired by some thick Nafion layers or clumps. For the gas-diffusion (E-TEK) electrode, the platinum utilization is mainly affected by the proton conduction provided by Nafion. The blocking effect of PTFE on the active sites is not serious. When the electrode is sufficiently impregnated with Nafion by an immersion method, the platinum utilization can reach 77.8%. Transmission electron micrographs reveal that although some thick Nafion layers and clumps are observed in the Pt/C + Nafion layer, the distribution of Nafion in the catalyst layer is basically uniform. The melted PTFE disperses in the catalyst layer very uniformly. No large PTFE clumps or wide net-like structure is observed. The reactant gas may have to diffuse evenly in the catalyst layer. (C) 1999 Elsevier Science S.A. All rights reserved.

Polyelectrolyte-functionalized ionic liquid for electrochemistry in supporting electrolyte-free aqueous solutions and application in amperometric flow injection analysis

As a green process, electrochemistry in aqueous solution without a supporting electrolyte has been described based on a simple polyelectrolyte-functionalized ionic liquid (PFIL)-modified electrode. The studied PFIL material combines features of ionic liquids and traditional polyelectrolytes. The ionic liquid part provides a high ionic conductivity and affinity to many different compounds. The polyelectrolyte part has a good stability in aqueous solution and a capability of being immobilized on different substrates. The electrochemical properties of such a PFIL-modified electrode assembly in a supporting electrolyte-free solution have been investigated by using an electrically neutral electroactive species, hydroquinone ( HQ) as the model compound. The partition coefficient and diffusion coefficient of HQ in the PFIL film were calculated to be 0.346 and 4.74 X 10(-6) cm(2) s(-1), respectively. Electrochemistry in PFIL is similar to electrochemistry in a solution of traditional supporting electrolytes, except that the electrochemical reaction takes place in a thin film on the surface of the electrode. PFILs are easily immobilized on solid substrates, are inexpensive and electrochemically stable. A PFIL-modified electrode assembly is successfully used in the flow analysis of HQ by amperometric detection in solution without a supporting electrolyte.

Poly(vinylidene fluoride-hexafluoropropylene)/organo-montmorillonite clays nanocomposite lithium polymer electrolytes

Polymer-clay nanocomposite (PCN) materials were prepared by intercalation of an alkyl-ammonium ion spacing/coupling agent and a polymer between the planar layers of a swellable-layered material, such as montmorillonite (MMT). The nanocomposite lithium polymer electrolytes comprising such PCN materials and/or a dielectric solution (propylene carbonate) were prepared and discussed. The chemical composition of the nanocomposite materials was determined with X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy, which revealed that the alkyl-ammonium ion successfully intercalated the layer of MMT clay, and thus copolymer poly(vinylidene fluoride-hexafluoropropylene) entered the galleries of montmorillonite clay. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were used to investigate the electrochemical properties of the lithium polymer electrolyte. Equivalent circuits were proposed to fit the EIS data successfully, and the significant contribution from MMT was thus identified. The resulting polymer electrolytes show high ionic conductivity up to 10(-3) S cm(-1) after felling with propylene carbonate.

Synthesis and ionic conductivity studies of solid polymer electrolytes based on modified alternating maleic anhydride copolymer with oligo(oxyethylene) side chains

Comb-like polymers (CP) based on modified alternating methyl vinyl ether/maleic anhydride copolymer with oligo-oxyethylene side chains of the type-O(CH2CH2O)(n)CH3 have been synthesized and characterized, and complexed with LiNO3 to form an amorphous polymer electrolyte. CP/salt complexes showed conductivity up to 10(-5) S/cm at room temperature. The temperature dependence of ionic conductivity suggests that the ion transport is controlled by segmental motion of the polymer, shown by linear curves obtained in Vogel-Tammann-Fulcher plots. The ionic conductivity maximum moves to a higher salt concentration as the temperature increases. IR results also indicate that the ester in CP might decompose at 140 degrees C and reproduce the maleic anhydride ring.

Lithium ion conducting polymer electrolytes based on alternating maleic anhydride copolymer with oligo-oxyethylene side chains

A comb polymer with oligo-oxyethylene side chains of the type -(CH2CB2O)(12)CH3 was prepared from methyl vinyl ether/maleic anhydride copolymer and poly (ethylene glycol) methyl ether. The polymer can dissolve LiClO4 salt to form homogeneous amorphous polymer electrolyte. The ac ion conduction was measured using the complex impedance method, and conductivities were investigated as functions of temperatures and salt concentration. The complexes were first found to have two classes of glass transition which increase with increasing salt content, The optimum conductivity attained at 25 degrees C is in the order of 5.50 x 10(-6)Scm(-1). IR spectroscopy was used to study the cation-polymer interaction.

SYNTHESIS AND CHARACTERIZATION OF A NEW COMB-LIKE POLYMER-BASED ON POLY(VINYL METHYL ETHER-ALT-MALEIC ANHYDRIDE) BACKBONE

A new comblike polymer host for polymer electrolyte was synthesized by reacting monomethyl ether of poly(ethylene glycol) with poly(vinyl methyl ether-alt-maleic anhydride) and endcapping the residual carboxylic acid with methanol. Butanone was selected as a solvent for the esterification in order to obtain a completely soluble product. The synthesis process was traced through by LR. Compared with the model compounds, the presumed structure of this comblike polymer has been proved to be valid by C-13 NMR The comb polymer is a white rubbery solid. It can be dissolved in butanone and THF, and manifests good film forming ability.

GAMMA-RADIATION INDUCED CROSS-LINKED PEO-LICLO4 SOLID-ELECTROLYTE SYSTEM

Aimed at raising the room temperature ionic conductivity of PEO-based solid polymer electrolyte and considered that the ionic conduction preferentially occurs in the amorphous phase, we lightly crosslinked the high MW PEO through gamma-irradiation and further suppressed the residual crystallinity by plasticizing with propylene carbonate. By incorporating LiClO4 salt to the above described polymer host, the ambient (25 degrees C) ionic conductivity of the electrolyte system could reach as high as 6.8 X 10(-4) S/cm. As the electrolyte was a crosslinked system, it was mechanically self-supportable. Based on the preliminary results of the electrochemical performance of the secondary lithium battery, assembled by using this kind of solid electrolyte and polyaniline as positive electrode, it is realized that the electrolyte thus prepared is of high expectancy.

SOLID-STATE VOLTAMMETRY OF ELECTROACTIVE SOLUTES IN POLYMER SOLVENTS (PEO) AT ULTRAMICROELECTRODES

This paper describes the electrochemical oxidation and reduction of electroactive solutes which are dissolved in and diffusing through the polymer electrolyte solvent, poly(ethylene oxide) (PEO). The characteristics of electrochemical reactions in polymeric solutions are discussed, including how rigid solvent environments affect mass transport rates, and the transport phenomenon of electroactive species in PEO with bathing gases is explained by using the voltammetric theory of ultramicroelectrodes. The possibility that the microelectrode coated with PEO film can be used as a gas sensor has been discussed.

纳米复合聚合物电解质的电化学研究

聚合物电解质在制备高能密度全固态铿电池、光电化学器件、气体传感器和电化学半导体等器件显示了重要的应用前景，成为近期的研究热点之一。然而，人们目前对聚合物电解质中离子传输、导电机理及电极界面动力学等问题的了解有限，这严重阻碍高性能聚合物电解质的研究和开发。本论文研究工作主要集中在纳米复合聚合物电解质中离子传输和导电机理的研究，内容和创新点表现在以下几个方面：1、设计制备了形状可控的纳米级金微带电极和铂、碳纤维微盘阵列电极。操作相对简单，在普通实验室中就可以制备，电极通过研磨就可以重复多次使用。2、选择四种不同分子量的PEG作为聚合物本体，杂多酸纳米粒子作为添加剂，和铿盐组成了有机一无机纳米复合聚合物电解质。用微盘电极的计时电流方法求出了杂多酸纳米粒子在聚合物电解质中的扩散系数，利用DSC技术和FT-IR光谱解释了离子之间相互作用的机理和电导率提高的原因。3、合成出不同侧链长的梳状丙烯酸铿／甲基丙烯酸聚乙二醇单甲醚醋聚合物电解质。用DSC，TGA和交流阻抗研究了纳米SiO2掺杂的梳状聚合物电解质的电化学和热力学性质。给出了铿离子在纳米复合聚合物电解质中随纳米SiO2含量变化的传输模型。黑抉巍一淤呱4、将聚环氧乙烷，盐和多壁碳纳米管掺杂在一起，制备出一种离子一电子混合导电的聚合物电解质纳米杂化薄膜。用贫流阻抗和DSC技术表征了杂化薄膜的导电性质和热力学行为，给出了体系的等效电路，解释了电导率增加的原因。5、将多壁碳纳米管和碳微珠分别和室温离子液体混合制备了两种无机／有机的纳米复合材料：多壁碳纳米管／离子液体和碳微珠／离子液体。利用交流阻抗技术研究了无机／有机的纳米复合材料的导电机理。用这两种复合材料制备的酶电极可以获得酶的直接电化学，且能够催化O2和H2O2的还原。