Design of a Self-Adaptive Down-Hole Layered Steam Injector and Its Application

Layered steam injection, widely used in Liaohe Oilfield at present, is an effective recovery technique to heavy oil reserves. Which makes the steam front-peak push forward uniformly, the amount of steam injection be assigned rationally, and the effect of injection steam be obtained as expected. To maintain a fixed ratio of layered steam injection and solve the problem of nonadjustable hole diameter with the change of layer pressure in the existing injectors, a new method is proposed in this paper to design layered steam injectors based on the dynamic balance theory According to gas-liquid two-phase flow theory and heat transfer theory, the energy equation and the heat conduction equation in boreholes are developed. By analyzing the energy equilibrium of water-steam passing through the injector hole, we find an expression to describe the relation between the cross-sectional area of injector hole and the layer pressure. With this expression, we provide a new set of calculation methods and write the corresponding computer program to design and calculate the main parameters of a steam injector. The actual measurement data show that the theoretically calculated results are accurate, the software runs reliably, and they provide the design of self-adjustable layered steam injectors with the theoretical foundation.

Response of the Bucket Foundation in Calcareous Sand under Horizontal Dynamic Load

Abstract: Experiments to determine the horizontal static bearing capacity are carried out first. The static bearing capacity is a reference for choosing the amplitudes of dynamic load. Then a series of experiments under dynamic horizontal load are carried out in laboratory to study the influences of factors, such as the scales of bucket, the amplitude and frequency of load, the density of soils etc.. The responses of bucket foundations in calcareous sand under horizontal dynamic load are analyzed according to the experimental results. The displacements of bucket and sand layer are analyzed.

A lattice dynamical treatment for the total potential energy of single-walled carbon nanotubes and its applications: relaxed equilibrium structure, elastic properties, and vibrational modes of ultra-narrow tubes

In this paper, we propose a lattice dynamic treatment for the total potential energy of single-walled carbon nanotubes (SWCNTs) which is, apart from a parameter for the nonlinear effects, extracted from the vibrational energy of the planar graphene sheet. The energetics, elasticity and lattice dynamics are treated in terms of the same set of force constants, independently of the tube structures. Based upon this proposal, we have investigated systematically the relaxed lattice configuration for narrow SWCNTs, the strain energy, the Young's modulus and Poisson ratio, and the lattice vibrational properties with respect to the relaxed equilibrium tubule structure. Our calculated results for various physical quantities are nicely in consistency with existing experimental measurements. In particular, we verified that the relaxation effect makes the bond length longer and the frequencies of various optical vibrational modes softer. Our calculation provides evidence that the Young's modulus of an armchair tube exceeds that of the planar graphene sheet, and that the large diameter limits of the Young's modulus and Poisson ratio are in agreement with the experimental values of graphite; the calculated radial breathing modes for ultra-narrow tubes with diameters ranging between 2 and 5 angstrom coincide with the experimental results and the existing ab initio calculations with satisfaction. For narrow tubes with a diameter of 20 angstrom, the calculated frequencies of optical modes in the tubule's tangential plane, as well as those of radial breathing modes, are also in good agreement with the experimental measurements. In addition, our calculation shows that various physical quantities of relaxed SWCNTs can actually be expanded in terms of the chiral angle defined for the corresponding ideal SWCNTs.

Fracture behavior of a Zr-metallic glass under dynamic compression

Dynamic planar compressive experiments on a typical tough Zr-BMG (Bulk Metallic Glass) were carried out under impact velocity of 500-600 m/sec and strain rate of 10(6)/s. The fracture surface of samples exhibits different fracture patterns at different parts of the sample. At a corner close to the front loading boundary, fracture patterns from the free edge toward the centre changed from equiaxial veins in microscale to periodic corrugations in nanoscale; in the middle of the sample, the fracture surface contains glazed zones laid out orderly along the same boundary. FEM simulation was performed to investigate the stress distributions in the impacted sample under a short duration impact loading. It has revealed that the fracture patterns changing from the free edge toward the centre were resulted from the fracture modes' changing from the tensile dominant fracture to the shear dominant fracture. Whereas at the middle part of the sample, fracture initiated from several parallel shear bands propagating close to the same boundary is due to a large strain or much higher shear stress in this area.

Using HPLC retention parameters to estimate fish bioconcentration factors of organic compounds

Reversed-phase high performance liquid chromatography (RP-HPLC) was employed to develop predictive models for fish bioconcentration factors (BCF) of organic compounds. Estimation of BCF from RP-HPLC retention parameters on octadecyl-bonded silica gel (ODS), cyanopropyl-bonded silica gel (CN), and phenyl-bonded silica gel (Ph) columns were investigated. The results show that, for a set of compounds belonging to different chemical classes, the CN stationary phase is the best one among the three columns and better than n-octanol/water model for BCF estimation. A multi-column RP-HPLC model, using the retention parameters on the CN and Ph columns as the variables of multiple linear regression equations, was further evaluated to estimate BCF of organic compounds belonging to different chemical classes, and the results show that the multi-column RP-HPLC model is better than that of any single RP-HPLC column for BCF estimation.

Synthesis of covalently bonded cellulose derivative chiral stationary phases with a bifunctional reagent of 3-(triethoxysilyl)propyl isocyanate

A bifunctional reagent of 3-(triethoxysilyl)propyl isocyanate (TEPI) was initially adopted as a spacer reagent to prepare the bonded types of chiral stationary phases (CSPs) with cellulose derivatives. The silica-based CSPs were chemically prepared with non-regioselective and regioselective approaches and their chiral resolving capabilities were evaluated in terms of HPLC resolution of test enantiomers. It was observed that the chiral recognition capabilities of the non-regioselectively prepared CSPs were influenced by the amount of TEPI used. And also, the regioselectively prepared CSP generally showed a slightly higher resolution power than the non-regioselectively prepared CSP, while the non-regioselective procedures were highly advantageous to rapid preparation. In addition, chiral recognition of the prepared CSPs was affected by the properties of the used silica matrices. (C) 2003 Elsevier B.V. All rights reserved.

Weak epitaxy growth of organic semiconductor thin films

The fabrication of organic semiconductor thin films is extremely important in organic electronic devices. This tutorial review-which should particularly appeal to chemists and physicists interested in organic thin-film growth, organic electronic devices and organic semiconductor materials-summarizes the method of weak epitaxy growth (WEG) and its application in the fabrication of high quality organic semiconductor thin films.

Laser light scattering of the molecular weight distribution of unfractionated phenolphthalein poly(aryl ether sulfone)

Two unfractionated samples of phenolphthalein poly( aryl ether sulfone) (PES-C) were characterized in CHCl3 at 25 degrees C by applying a recently developed laser light-scattering (LLS) procedure. The Laplace inversion of precisely measured intensity-intensity time correlation function lead us first to an estimate of the characteristic line-width distribution G(Gamma) and then to the translational diffusion coefficient distribution G(D). A combination of static and dynamic LLS results enabled us to determine D = (2.69 x 10(-4))M(-0.553), which agrees with the calibration of D = (2.45 x 10(-4))M(-0.55) previously established by a set of narrowly distributed PES-C samples. Using this newly obtained scaling between D and M, we were able to convert G(D) into a differential weight distribution f(w)(M) for the two PES-C samples. The weight-average molecular weights calculated from f(w)(M) are comparable to that obtained directly from static LLS. Our results showed that using two broadly distributed samples instead of a set of narrowly distributed samples have provided not only similar final results, but also a more practical method for the PES-C characterization. (C) 1997 John Wiley & Sons, Inc.

A DYNAMIC LASER LIGHT-SCATTERING STUDY OF CHITOSAN IN AQUEOUS-SOLUTION

The solution behavior of four chitosans (91% deacetylated chitin) with different molecular weights in 0.2M CH3COOH/0.1M CH3COONa aqueous solution was investigated at 25 degrees C by dynamic laser light scattering (LLS). The Laplace inversion of the precisely measured intensity-intensity time correlation function leads us to an estimate of the line-width distribution G(Gamma), which could be further reduced to a translational diffusion coefficient distribution G(D). By using a combination of static and dynamic LLS results, i.e. Mw and G(D), we were able to establish a calibration of D = k(D)M(-alpha D) with k(D) = (3.14 +/- 0.20) X 10(-4) and alpha(D) = 0.655 +/- 0.015. By using this calibration, we successfully converted G(D) into a molecular weight distribution f(w)(M). The larger alpha(D) value confirms that the chitosan chain is slightly extended in aqueous solution even in the presence of salts. This is mainly due to its backbone and polyelectrolytes nature. As a very sensitive technique, our dynamic LLS results also revealed that even in dilute solution chitosan still forms a small amount of larger sized aggregates that have ben overlooked in previous studies. The calibration obtained in this study will provide another way to characterize the molecular weight distribution of chitosan in aqueous solution at room temperature. (C) 1995 John Wiley & Sons, Inc.

Influence of the earth rotation on the interfacial wave solutions and wave-induced tangential stress in a two-layer fluid system

Interfacial waves and wave-induced tangential stress are studied for geostrophic small amplitude waves of two-layer fluid with a top free surface and a flat bottom. The solutions were deduced from the general form of linear fluid dynamic equations of two-layer fluid under the f-plane approximation, and wave-induced tangential stress were estimated based on the solutions obtained. As expected; the solutions derived from the present work include as special cases those obtained by Sun et al. (2004. Science in China, Set. D, 47(12): 1147-1154) for geostrophic small amplitude surface wave solutions and wave-induced tangential stress if tire density of the upper layer is much smaller than that of the lower layer. The results show that the interface and the surface will oscillate synchronously, and the influence of the earth's rotation both on the surface wave solutions and the interfacial wave solutions should be considered.

河道砂油藏产能预测系统研究

Productivity prediction is a serious factor to oil reservoir management and working out economic plans so that it is paid great attention to all the time. Gudao Oil Field, which has been yielding more than 100 million tons of crude oil accumulatively since it was put into developing in 1970's as a complete set of oil field, now entering double extra high water-bearing period after productivity construction, stable production and depletion stage. It's main layer series of development is thought to be type of channel sand reservoir in east China. Form channel sand reservoir in upper Guantao Group of Shengli Oil Field, there are several large oil fields such as Gudao, Gudong and Chengdao etc. with almost one-third reserves of whole Shengli Oil Field. It is considered the common characteristics in this area would be that the layer is less developed, the sand distribution is sporadic, the connectivity is weak, the heterogeneity is strong in plane, the oil layer is unconsolidated with big porosity, high permeability and serious sanding, and the oil is heavy. Because of the restricted factors to productivity of this kind of reservoir, it is very significant to study the productivity prediction this kind of reservoir. By selecting the upstream fluvial reservoir in Guantao Group of Neogene system as researching object, the author studied the forecasting technology with heterogeneous reservoir. Firstly, the author constructed the 3D subtle geological model quantificationally through researching exploitation geology in the way of combination of dynamic and static methods. Secondly, by the aid of dynamic material obtained while producing, the author analyzed the oil distribution law and influencing factors, then finished dynamic oil reservoir description on the basis of static oil reservoir description. Thirdly, via comparing and analyzing all the forecasting methods of productivity existed, the author developed a set of method to forecast productivity of single well and oil field which fit to channel sand reservoir. At last, under the support of ORACLE database, with the advanced computer technology, the author programmed the software called 'Channel Sand Reservoir Prediction System'. Up to now, this system has been putting into use in Gudao Oil Field and very successful.

降雨触发滑坡的非线性模型与斜坡演化的混沌效应

This paper analyzes landsliding process by nonlinear theories, especially the influence mechanism of external factors (such as rainfall and groundwater) on slope evolution. The author investigates landslide as a consequence of the catastrophic slide of initially stationary or creeping slope triggered by a small perturbation. A fully catastrophe analysis is done for all possible scenarios when a continuous change is imposed to the control parameters. As the slip surface continues and erosion due to rainfall occurs, control parameters of the slip surface may evolve such that a previously stable slope may become unstable (e.g. catastrophe occurs), when a small perturbation is imposed. Thus the present analysis offers a plausible explanation to why slope failure occurs at a particular rainfall, which is not the largest in the history of the slope. It is found, by analysis on the nonlinear dynamical model of the evolution process of slope built, that the relationship between the action of external environment factors and the response of the slope system is complicatedly nonlinear. When the nonlinear action of slope itself is equivalent to the acting ability of external environment, the chaotic phenomenon appears in the evolution process of slope, and its route leading to chaos is realized with bifurcation of period-doublings. On the basis of displacement time series of the slope, a nonlinear dynamic model is set up by improved Backus generalized linear inversion theory in this paper. Due to the equivalence between autonomous gradient system and catastrophe model, a standard cusp catastrophe model can be obtained through variable substitution. The method is applied to displacement data of Huangci landslide and Wolongsi landslide, to show how slopes evolve before landsliding. There is convincing statistical evidence to believe that the nonlinear dynamic model can make satisfied prediction results. Most important of all, we find that there is a sudden fall of D, which indicates the occurrence of catastrophe (when D=0).

大港油田孔南地区孔一段储层流动单元研究

The main reservoir type in the south of Dagang Oilfield is alluvial reservoir. In this paper, the reservoir structure model and the distribution of connected body and flow barrier were built on base of the study of high-resolution sequential stratigraphic skeleton and fine sedimentary microfacies on level of single sandbody. Utilizing the static and dynamic data synthetically and carrying out the comparision of the classification method for reservoir flow unit in different reservoir, the criterion, which can be used to classify the flow unit in first section of Kongdian formation of Kongnan area, was defined. The qualitative method of well-to-well correlation and the quantitative method of conditional simulation using multiple data are adopted to disclose the oil and water moving regulation in different flow unit and the distribution rule of remaining oil by physical simulation measure. A set of flow unit study method was formed that is suit for the Dagang Oilfield on account of the remaining oil production according to the flow unit. Several outstanding progresses was obtained in the following aspects:It is considered that the reservoir structure of Zao V iow oil group- Zao Vup4 layerand are jigsaw-puzzled reservoir, while ZaoVup3-ZaoVupi layers are labyrinth reservoir,which are studied on base of high-resolution sequential stratigraphic skeleton on the levelof single sandbody in first section of Kongdian formation of Kongnan area and accordingto the study of fine sedimentary microfacies and fault sealeing.When classifying the flow unit, only permeability is the basic parameter using thestatic and dynamic data and, and also different parameters should be chose or deleted, suchas porosity, effective thickness, fluid viscosity and so on, because of the weak or stronginterlayer heterogeneous and the difference of interlayer crude oil character.The method of building predicting-model of flow unit was proposed. This methodis according to the theories of reservoir sedimentology and high-resolution sequencestratigraphic and adopts the quantitative method of well-to well correlation and the quantitative method of stochastic simulation using integrateddense well data. Finally the 3-D predicting-model of flow unit and the interlay er distribution model in flow unit were built which are for alluvial fan and fan delta fades in first section of Kongdian formation of Kongnan area, and nine genetic model of flow unit of alluvial environment that spread in the space were proposed.(4) Difference of reservoir microscopic pore configuration in various flow units and difference of flow capability and oil displacement effect were demonstrated through the physical experiments such as nuclear magnetic resonance (NMR), constant rate mercury penetration, flow simulation and so on. The distribution of remaining oil in this area was predicted combining the dynamic data and numerical modeling based on the flow unit. Remaining oil production measure was brought up by the clue of flow unit during the medium and late course of the oilfield development.