Preparation and properties of conductive polyaniline/poly-omega-aminoundecanoyle fibers

Historically, polyaniline (PANI) had been considered an intractable material, but it can be dissolved in some solvents. Therefore, it could be processed into films or fibers. A process of preparing a blend of conductive fibers of PANI/poly-omega-aminoun-decanoyle (PA11) is described in this paper. PANI in the emeraldine base was blended with PA11 in concentrated sulfuric acid (c-H,SO,) to form a spinning dope solution. This solution was used to spin conductive PANI/PA11 fibers by wet-spinning technology. As-spun fibers were obtained by spinning the dopes into coagulation bath water or diluted acid and drawn fibers were obtained by drawing the as-spun fibers in warm drawing bath water. A scanning electron microscope was employed to study the effect of the acid concentration in the coagulation bath on the microstructure of as-spun fibers. The results showed that the coagulating rate of as-spun fibers was reduced and the size of pore shrank with an increase in the acid concentration in the coagulation bath. The weight fraction of PANI in the dope solution also had an influence on the microstructure of as-spun fibers. The microstructure of as-spun fibers had an influence on the drawing process and on the mechanical properties of the drawn fibers. Meanwhile, the electrically conductive property of the drawn fibers with different percentage of PANI was measured.

Morphological study on water-borne conducting polyaniline-poly(ethylene oxide) blends

Conducting polyaniline-poly(ethylene oxide) blends were prepared from their aqueous solutions. The blends displayed an electrical conductivity percolation threshold as low as 1.83 wt % of polyaniline loading. As demonstrated by scanning electron microscopy, polarized optical microscopy, and wide-angle X-ray diffraction studies, the conducting polyaniline took a fibrillar morphology in the blend, and it existed only in the amorphous phase of poly(ethylene oxide). A three-phase model combining morphological factors instead of a two-phase model was proposed to explain the low-conductivity percolation threshold.

Covalently attached multilayer assemblies containing photoreactive diazo-resins and conducting polyaniline

We reported on the multilayer architecture containing diazo-resins (DAR) as polycations and polyaniline poly(aniline-co-N-propanesulfonic acid aniline) (PAPSAH) as polyanions held together by electrostatic interaction. Upon UV irradiation, the adjacent interfaces of the multilayer reacted to form a covalently crosslinking structure which greatly improved the stability of the films as confirmed by solvent etching experiments. These changes were confirmed by UV-Vis and FTIR spectroscopy. The thickness of the covalently attached films were characterized with small angle X-ray diffraction (SAXD) and a value of 30.0 Angstrom per bilayer was obtained. This type of film was further characterized by cyclic voltammetry which showed that the electroactive property of PAPSAH was still kept in the films after photoreaction. (C) 2000 Elsevier Science B.V. All rights reserved.

Organic acid doped polyaniline derivatives

Soluble poly (o-toluidine) (POT), poly(o-anisidine) (PAs) and poly (o-chloroaniline) (PCAn) were doped with camphorsulfonic acid (CSA). The conductivity and UV-Vis spectra of the CSA-doped POT, PAs and PCAn were studied. These properties were found to be dependent on the solvent used. The cast films from m-cresol solution exhibit more effective doping and higher conductivity.

Solution properties of doped polyaniline

Solution properties of polyaniline (PAn) doped by camphorsulfonic acid (CSA) were examined. PAn-CSA behaves like a polyelectrolyte to different extents depending on the solvent used. In an m-cresol/chloroform solution, PAn-CSA exhibits an expanded chain conformation because of its polyelectrolytic properties. Dilute and concentrated solution properties of PAn-CSA indicate that PAn-CSA is a semirigid polymer which has strong interchain interactions.

POLYANILINE-DISPERSED MERCURY-ELECTRODE FOR THE DETECTION OF MONOCHLORAMINE AND DICHLORAMINE

A novel type of electrochemical detector based on a polyaniline-dispersed mercury-coated glassy carbon chemically modified electrode was investigated for the detection of monochloramine and dichloramine. A polyaniline dispersed-mercury modified electrode, which was prepared by coating polyaniline on a thin mercury film electrode using fast-sweep voltammetry, was developed. The selectivity could be altered using various counter ions incorporated into the polymer. The results indicated that the use of a conducting polymer-based electrochemical sensor for the selective determination of chloramine is a feasible approach.

INTERPRETATION OF THE PHOTOREDUCTION CURRENT RESPONSE ON POLYANILINE MODIFIED ELECTRODE

The photoreduction current response on a polyaniline modified electrode is interpreted as photo-assisted reduction of oxygen dissolved in the electrolyte solution but not due to the excited species PAn* and PAn* dagger. The effect of light is just the same as that of the electrode rotating or of stirring of the electrolyte which accelerates the oxygen dissolved in the electrolyte solution to react with leucoemeraldine (reduced polyaniline). The potentiostat is set to reduce the oxidized polyaniline at constant potential, thus producing a reduction current.

ELECTROCATALYTIC OXIDATION OF ASCORBIC ACID AT POLYANILINE FILM MODIFIED GLASSY CARBON ELECTRODES

A conducting polyaniline (PAn) film modified glassy carbon (GC) electrode was prepared by electrochemical polymerization. The electrochemical behavior of ascorbic acid (AH(2)) in aqueous solution at this PAn modified electrode was studied in detail. The experimental results show that PAn film modified electrode has good electrocatalytic activity on the oxidation of ascorbic acid in aqueous solution over a wide range of pH value, among which pH 4 is the optimum condition. The oxidation process of ascorbic acid at PAn film electrode can be regarded as an EC catalytic mechanism. The kinetic process of the catalytic reaction was investigated by rotating disk electrode (RDE) coated with PAn films. The rate constant of the catalytic reaction was evaluated. The catalytic peak currents are proportional to the concentrations tions of ascorbic acid in the range of 5 x 10(-2)-1 x 10(-6) mol . L-1. The PAn film elec trodes give very stable responce for the oxidation of ascorbic acid. The present investigation shows the posibility of using PAn film modified electrode for the determination of ascorbic acid.

POLYANILINE CHEMICALLY MODIFIED ELECTRODE FOR DETECTION OF ANIONS IN FLOW-INJECTION ANALYSIS AND ION CHROMATOGRAPHY

An electrochemical detector based on a polyaniline conducting polymer chemically modified electrode (PAn CME) was developed for use in flow-injection analysis and ion chromatography. Iodide, bromide, thiocyanate and thiosulphate are detected by using ion chromatography with a PAn CME electrochemical detector. The detection limits are 1, 5, 10 and 10 mgl-1, respectively. The CME response for electroinactive anions varies selectively with the mobile phase composition in flow-injection analysis. By this approach, perchlorate, sulphate, nitrate, iodide, acetate and oxalate can be detected conveniently and reproducibly over a linear concentration range of at least 3 orders of magnitude. The electrode is stable for over 2 weeks with no evidence of chemical or mechanical deterioration.

STUDY ON POLYANILINE FILM WITH HIGH-DENSITY AND HIGH MECHANICAL STRENGTH

Free-standing film of polyaniline with excellent mechanical and electrical properties has been successfully prepared by using the solution-casting method. The results show that its tensile strength, Young's modulus and elongation at break are about 87.9 MPa, 1563.9 MPa and 10.2%, respectively. It is essential that the soluble polyaniline should be appropriately treated in some suitable organic solvents before making a free-standing film. Films having lustrous, smooth surface, high density and good flexibili...

Anticorrosion performance of polyaniline nanostructures on mild steel

Different one-dimensional nanostructured polyanilines were synthesized in sulfuric acid solutions by conventional polymerization, interfacial polymerization and direct mixed reaction, respectively. The products were characterized with SEM, UV-vis and FTIR and the anticorrosion performance of products on mild steel were studied using electrochemical measurement in 3.5% NaCl aqueous solution. Results showed that the polyaniline nanofibers synthesized by direct mixed reaction have uniform morphology with diameters of 60-100 nm and more excellent protective properties than conventional aggregated polyaniline. Comparative studies revealed that the nanostructure and morphology of polyaniline could influence its anticorrosion performance. (C) 2010 Elsevier B.V. All rights reserved.

Investigation of the Mechanical Properties of Thin Films by Nanoindentation, Considering the Effects of Thickness and Different Coating-Substrate Combinations

In order to further investigate nanoindentation data of film-substrate systems and to learn more about the mechanical properties of nanometer film-substrate systems, two kinds of films on different substrate systems have been tested with a systematic variation in film thickness and substrate characteristics. The two kinds of films are aluminum and tungsten, which have been sputtered on to glass and silicon substrates, respectively. Indentation experiments were performed with a Nano Indent XP II with indenter displacements typically about two times the nominal film thicknesses. The resulting data are analyzed in terms of load-displacement curves and various comparative parameters, such as hardness, Young's modulus, unloading stiffness and elastic recovery. Hardness and Young's modulus are investigated when the substrate effects are considered. The results show how the composite hardness and Young's modulus are different for different substrates, different films and different film thicknesses. An assumption of constant Young's modulus is used for the film-substrate system, in which the film and substrate have similar Young's moduli. Composite hardness obtained by the Joslin and Oliver method is compared with the directly measured hardness obtained by the Oliver and Pharr method.

Magnetron Sputtering Growth of InAs0.3Sb0.7 Films on (100) GaAs Substrates: Strong Effect of Growth Conditions on Film Structure

The growth of highly lattice-mismatched InAs0.3Sb0.7 films on (100) GaAs Substrates by magnetron Sputtering has been investigated and even epitaxial lnAs(0.3)Sb(0.7) films have been successfully obtained. A strong effect of the growth conditions on the film structure was observed, revealing that there was a growth mechanism transition from three-dimensional nucleation growth to epitaxial layer-by-layer growth mode when increasing the substrate temperature. A qualitative explanation for that transition was proposed and the critical conditions for the epitaxial layer-by-layer growth mode were also discussed.

Preparation And Tribology Studies of Alkyl Carboxylic Acid Monolayer Films on Pei-Coated Glass Substrate

首次在涂敷PEI的玻璃表面上制备了癸酸及全氟癸酸的单分子层膜。研究了成膜机理及摩擦特性。结果表明。脱水剂DCCD促进了癸酸或全氟癸酸与PEI酞胺化的反应。导致两种羧酸在PEI表面产生了靠化学键（酞胺键）连接的稳定的单分子层膜,摩擦、磨损实验表明。单分子层有机膜的摩擦特性受膜的组成、表面能及有序性和堆积密度的重要影响。表面能越低,有序性和堆积密度越高。摩擦系数越低。与碳氢化合物相比。碳氟化合物形成的有序膜具有更高的强度和抗磨性能。

Essential and Non-Essential Work of Fracture of PI/SiO2 Hybrid Thin Films

Essential work of fracture (EWF) analysis is used to study the effect of the silica doping level on fracture toughness of polyimide/silica (PI/SiO2) hybrid films. By using double-edge-notched-tension (DENT) specimens with different ligament lengths, it seems that the introduction of silica additive can improve the specific essential work of fracture (w (e) ) of PI thin films, but the specific non-essential work of fracture (beta w (p) ) will decease significantly as the silica doping level increasing from 1 to 5 wt.%, and even lower than that of neat PI. The failure process of the fracture is investigated with online scanning electron microscope (SEM) observation and the parameters of non-essential work of fracture, beta and w (p) , are calculated based on finite element (FE) method.