Cloning, characterization, and gene expression analysis of a novel cadmium metallothionein gene in Tetrahymena pigmentosa

A novel cadmium-inducible metallothionein (MT) gene (Tpig-MT1) was cloned and sequenced from the ciliate Tetrahymena pigmentosa. The number of deduced amino acids is 118. The polypeptide possesses CCC and CC clusters characteristic of typical Tetrahymena Cd-inducible MTs. The structure of Tpig-MT1 is different from the reported Cd-MT in T. pyriformis, T. thermophila and T. pigmentosa. Tpig-MT1 contains two intragenic tandem repeats with 72.9% identity described as Tpig-MT1 (repeat A1) and Tpig-MT1 (repeat A2). The transcriptional response of Tpig-MT1 gene to different heavy metals (Cd, Cu, Zn, Hg, Pb) and oxidative stress (H2O2) was measured using real-time quantitative PCR. The results showed that the gene was quickly induced (1 h) by the five heavy metals and the order of expression level was Hg>Pb>Cd>Cu>Zn. The induction effect of H2O2 was 5-fold after about 15 min, but soon decreased to a non-significant level (30 min). The genetic diversity of Tetrahymena MT genes is discussed in relation to the unique structure of the Tpig-MT1 gene and other reported Cd-MT isoforms. (C) 2008 Elsevier B.V. All rights reserved.

Effects of cadmium on chlorophyll content, photochemical efficiency, and photosynthetic intensity of Canna indica Linn.

The effects of cadmium (Cd2+) on growth status, chlorophyll (Chl) content, photochemical efficiency, and photosynthetic intensity were studied on Canna indica Linn. Plant specimens that were produced from a constructed wetland and precultivated hydroponically in 20 L of 1/10 Hoagland solution under greenhouse conditions for I week were exposed to cadmium in concentrations of 0, 0.4, 0.8, 1.6 and 3.2 mg L- Cd2+, respectively. The results show that leaves were injured in the Cd2+ solution by the third day of exposure and the injury became more serious with an increase in the applied heavy metal. Under 3.2 mg L-1 Cd2+ treatment, growth retardation, the decrease of chlorophyll content from 0.70 to 0.43 mg g(-1) FW, and a decrease in Chl a/b ratio from 2.0 to 1.2 were observed. Chl a was more sensitive than Chl b to Cd2+ stress. The decrease was the same with photochemical efficiency. Photosynthetic intensity decreased by 13.3% from 1.5X10(4) mumol m(-2)s(-1) CO2 in control to 1.3x10(4) mumol m(2)s(-1) CO2 in the treatment of 3.2 mg L-1. Because Canna species are used in heavy metal phytoremediation, these results show that C. indica can tolerate 0.4 to 0.8 mg L-1 Cd2+. Therefore, it is a potential species for phytoremediation of cadmium with some limitations only at higher concentrations.

Partial oxidation reforming of biomass fuel gas over nickel-based monolithic catalyst with naphthalene as model compound

With naphthalene as biomass tar model compound, partial oxidation reforming (with addition of O-2) and dry reforming of biomass fuel gas were investigated over nickel-based monoliths at the same conditions. The results showed that both processes had excellent performance in upgrading biomass raw fuel gas. Above 99% of naphthalene was converted into synthesis gases (H-2+CO). About 2.8 wt% of coke deposition was detected on the catalyst surface for dry reforming process at 750 degrees C during 108 h lifetime test. However, no Coke deposition was detected for partial oxidation reforming process, which indicated that addition of O-2 can effectively prohibit the coke formation. O-2 Can also increase the CH4 conversion and H-2/CO ratio of the producer gas. The average conversion of CH4 in dry and partial oxidation reforming process was 92% and 95%, respectively. The average H-2/CO ratio increased from 0.95 to 1.1 with the addition of O-2, which was suitable to be used as synthesis gas for dimethyl ether (DME) synthesis.