AMPS modeling of light J-V characteristics of a-Si based solar cells

AMPS (Analysis of microelectronic and photonic structures) mode,which was developed by Pennsylvania State University, has been used to module the light J-V characteristics of a-Si solar cells with a structure of TCO/p-a-SiC:H/i-a-Si:H/n-a-Si:H/ metal. The effects of valence band offset and contact barriers at p/i and TOC/p, n/metal interfaces on the light J-V characteristics have been examined. The modeling has qualitatively categorized and explained the non-ideal J-V behaviors (rollover, crossover, Voc shift,and rollunder) observed in a-Si based solar cells.

Recyclable heterogeneous Rh/SiO2 catalyst enhanced by organic PPh3 ligand

Heterogeneous PPh3-Rh/SiO2 catalysts for hydroformylation of olefins, prepared by direct doping of phosphine onto the heterogeneous Rh/SiO2 precursor, exhibited high activity and selectivity towards aldehydes, which originated from chemical coordination bond between the phosphine and Rh metal nantoparticles on the SiO2 support.

Undercut structures fabricated by microtransfer printing combined with UV exposure and their applications

In this paper. the undercut structures were fabricated by microtransfer printing of metal films on the surface of photoresist combined with UV exposure and photoresist film developing. The patterned metal films were used as mask to realize the selective UV exposure of photoresist Firstly. The undercut structures. which consist of the top metal films and the patterned bottom photoresist, formed in the subsequent developing process because of the lateral dissolving of photoresist at the edge of the unexposed regions. The method proposed in this paper has wider tolerance to the changing of the patterning parameters. but, without effect on patterning resolution since the metal film was used as the top layer. The undercut Structures were Used as separators to pattern passive-matrix display of organic light-emitting diodes (OLEDs). No visible difference of the device performance was observed Compared with the OLEDs patterned by the shadow mask.

Synthesis and characterization of ferrocene-terminated ruthenium phenylacetylide complexes with alligator clips

Ferrocene-terminated trans/Ru(dppm)(2) (dppm=Ph2PCH2PPh2)-contained molecular wires with alligator clips were prepared. They are suitable for self-assembly on gold electrode to investigate the influence of metal incorporation on the electron transportation property of the molecular wires.

Preparation of rare earth ion induced conformation-specific anti-calmodulin monoclonal antibody

Monoclonal antibody technique was employed to detect the conformational change of calmodulin induced by metal ions. Bovine calmodulin was firstly modified by 2,4-dinitrofluorobenzene to improve its immunogenicity, then, the derived protein was saturated with trivalent europium ions and injected to Balb/c mice as antigen. After four times of immunization, a corresponding antibody was detected and its titer in serum was determined as 1 : 12 000. By fusing of the spleen cells with hybridoma cells, a europium induced conformation-specific anti-calmodulin monoclonal antibody cell strain named as 2C3 was produced successfully. The molecular recognition ability of antibody to apocalmodulin and holocalmodulin showed a significant difference, indicating that this antibody could be applied to the studies of different effects of metal ions on the conformational change of calmodulin and its interaction with target molecules.

Fluorescence spectra of hemorrhagin III from the snake venom of Agkistrodon acutus

Hemorrhagin III (AaH III) was separated and purified from the crude snake venom of Agkistrodon acutus, and its molecule weight was determined accurately to be 23; 284.4 +/- 0.1 by LDI1700-MALDI-TOF-MS. Emission spectra of AaH III showed that Trp residues were located by a great degree in the hydrophobic area. Addition of SDS and guanidine-HCl led to change of the molecular conformation of AaH III, and caused the fluorescence quenching of Trp residues. The red-shifted emission band of AaH III after adding guanidine-HCl showed that Trp residues exposed in polar solvents. The effects of pH, EDTA and metal ions on the fluorescence spectra of AaH III were also investigated.

Factors affecting the protease activity of venom from jellyfish Rhopilema esculentum Kishinouye

In this paper, the effects of some chemical and physical factors such as temperature, pH values, glycerol, and divalent metal cations on the protease activity of venom from jellyfish, Rhopilema esculentum Kishinouye, were assayed. Protease activity was dependent on temperature and pH values. Zn2+, Mg2+, and Mn2+ in sodium phosphate buffer (0.02 M, pH 8.0) could increase protease activity. Mn2+ had the best effects among the three metal cations and the effect was about 20 times of that of Zn2+ or Mg2+ and its maximal protease activity was 2.3 x 10(5) U/mL. EDTA could increase protease activity. PMSF had hardly affected protease activity. O-Phenanthroline and glycerol played an important part in inhibiting protease activity and their maximal inhibiting rates were 87.5% and 82.1%, respectively. (c) 2005 Elsevier Ltd. All rights reserved.

Preparation of Dendritic Copper Nanostructures and Their Characterization for Electroreduction

Dendritic copper nanostructures of different morphologies were synthesized by a surfactant-free electrochemical method. Single crystal nature of the nanostructures was revealed from their X-ray diffraction and electron diffraction patterns. Mechanism of dendrite formation was discussed from thermodynamic aspects using the concept of supersaturation. Supersaturation of the copper metal reduced on the surface of the electrode was the crucial factor for the generation of different morphologies. Effects of applied potential, temperature, and the solution concentration on the supersaturation were studied. The NO3- and H2O2 electroreduction ability of the dendritic materials was tested. Use of copper dendrite-modified electrode as NO3- sensor was demonstrated.

Effect of temperature on dislocation emission from crack tip for BCC metal Mo

The effect of thermally activated energy on the dislocation emission from a crack tip in BCC metal Mo is simulated in this paper. Based on the correlative reference model on which the flexible displacement boundary scheme is introduced naturally, the simulation shows that as temperature increases the critical stress intensity factor for the first dislocation emission will decrease and the total number of emitted dislocations increase for the same external load. The dislocation velocity and extensive distance among partial dislocations are not sensitive to temperature. After a dislocation emission, two different deformation slates are observed, the stable and unstable deformation states. In the stable deformation slate, the nucleated dislocation will emit from the crack tip and piles up at a distance far away from the crack tip, after that the new dislocation can not be nucleated unless the external loading increases. In the unstable deformation state, a number of dislocations can be emitted from the crack lip continuously under the same external load.

Effect of Particle Size on the Formation of Adiabatic Shear Band In Particle Reinforced Metal Matrix Composites

In this paper, the effect of particle size on the formation of adiabatic shear band in 2024 All matrix composites reinforced with 15% volume fraction of 3.5, 10 and 20 mum SiC particles was investigated by making use of split Hopkinson pressure bar (SHPB). The results have demonstrated that the onset of adiabatic shear banding in the composites strongly depends on the particle size and adiabatic shear banding is more readily observed in the composite reinforced with small particles than that in the composite with large particles. This size dependency phenomenon can be characterized by the strain gradient effect. Instability analysis reveals that high strain gradient is a strong driving force for the formation of adiabatic shear banding in particle reinforced metal matrix composites (MMCp).

Strain Gradient Effects on Deformation Strengthening Behavior of Particle Reinforced Metal Matrix Composites

Dislocation models with considering the mismatch of elastic modulus between matrix and reinforcing particles are used to determine the effective strain gradient \ita for particle reinforced metal matrix composites (MMCp) in the present research. Based on Taylor relation and the kinetics of dislocation multiplication, glide and annihilation, a strain gradient dependent constitutive equation is developed. By using this strain gradient-dependent constitutive equation, size-dependent deformation strengthening behavior is characterized. The results demonstrate that the smaller the particle size, the more excellent in the reinforcing effect. Some comparisons with the available experimental results demonstrate that the present approach is satisfactory.