Rheology, morphology and mechanical properties of compatibilized poly(vinylidene fluoride) (PVDF)/thermoplastic polyurethane (TPU) blends

Compatibilized blends of poly(vinylidene fluoride) (PVDF) and thermoplastic polyurethane (TPU) were developed using maleated PVDF (PVDF-g-MA). Excellent compatibilization between PVDF and TPU was demonstrated by theological, morphological, and mechanical measurements. The introduction of PVDF-g-MA into the PVDF/TPU blends caused an increase in viscosity and storage modulus. Much finer morphology was clearly observed by SEM. The tensile tests showed that the tensile strength and ultimate elongation achieved a significant improvement with addition of PVDF-g-MA.

Novel Method for Preparation of Polypropylene Blends with High Melt Strength by Reactive Compounding

Ultrafine full-vulcanized polybutadiene rubber(UFBR) with particle sizes of ca. 50-100 nm were used for modifying mechanical and processing performances of polypropylene(PP) with PP-g-maleic anhydride(PP-g-MA) as a compatibilizer for enhancing the interfacial adhesion between the two components. The morphology, dynamical rheology response and mechanical properties of the blends were characterized by means of SEM, rheometer and tensile test, respectively.

A novel preparation method of maleic anhydride grafted syndiotactic polystyrene and its blend performance with nylon6

This work is intended to provide a method for the preparation of maleic anhydride grafted syndiotactic polystyrene (sPS-g-MA). In particular, a novel solid reaction method by a radical grafting approach is investigated. The grafting reaction is performed at a solid state, where the syndiotactic polystyrene (sPS) is swollen in solvent at relatively low temperature compared to the conventional melt modification method. The formation of sPS-g-MA is directly confirmed by Fourier transform infrared spectroscopy and by the morphology observation of sPS/polyamide-6 (Nylon6) blends, when sPS-g-MA is used as a reactive compatibilizer.

聚β-羟基丁酸酯顺丁烯二酸酐接枝共聚物的等温结晶动力学和熔融行为

采用DSC方法对聚 β 羟基丁酸酯顺丁烯二酸酐接枝共聚物 (PHB g MA)的等温结晶动力学和熔融行为进行了研究 .结果表明 ,顺丁烯二酸酐的引入使得聚 β 羟基丁酸酯的结晶能力下降 ,但是并没有改变它的结晶成核机理和生长方式 .随着接枝率的增加 ,结晶活化能增加 .等温结晶后的PHB g MA表现出双熔融行为 ,这是在升温过程中发生熔融重结晶的结果

Preparation, characterization, and crystallization of naphthalene-labeled polypropylene

Naphthalene-labeled polypropylene (PP) was prepared by melt reaction of maleic anhydride-grafted-polypropylene (PP-g-MA) with 1-aminonaphthalene in a Barabender mixer chamber. The structure of the product was analyzed with fourier transform infrared (FT-IR), ultraviolet (UV) and fluorescence. The results showed that naphthyl groups grafted onto the PP molecular chains through the imide bonds formed between MA and 1-aminonaphthalene. The content of the chromophores was 1.8 X 10(-4) mol g(-1) measured by elemental analysis. Isothermal crystallization behavior was studied by differential scanning calorimeter (DSC). Labeled PP had a higher crystallization rate than PP-g-MA. Wide-angle X-Ray diffraction (WAXD) analysis revealed that labeled PP had higher crystallinity than PP-g-MA.

Toughening PA1010 with a functionalized saturated polyolefin elastomer

Polyamide (PA)1010 is blended with a saturated polyolefin elastomer, ethylene-cu-olefin copolymer (EOCP). To improve the compatibility of PA1010 with EOCP, different grafting rates of EOCP with maleic anhydride (MA) are used. The reaction between PA1010 and EOCP-g-MA during extrusion is verified through an extraction test. Mechanical properties, such as notched Izod impact strength, elongation at break, etc., are examined as a function of grafting rate and weight fraction of elastomer. It was found that in the scale of grafting rate (0.13-0.92 wt %), 0.51 wt % is an extreme point for several mechanical properties. Elastomer domains of PA1010/ EOCP-g-MA blends show a finer and more uniform dispersion in the matrix than that of PA1010/EOCP blends. For the same grafting rate, the average sizes of elastomer particles are almost independent on the contents of elastomer, but for different grafting rates, the particle sizes are decreased with increasing grafting rate. The copolymer formed during extrusion strengthens the interfacial adhesion and acts as an emulsifier to prevent the aggregation of elastomer in the process of blending. (C) 2000 John Wiley & Sons, Inc.

聚β-羟基丁酸酯顺丁烯二酸酐接枝共聚物的研究

采用DSC、TGA、POM和WAXD等方法对聚 β 羟基丁酸酯 (PHB)及其接枝顺丁烯二酸酐共聚物 (PHB g MA)的结晶行为、热稳定性和生物降解特性进行了研究 .结果表明接枝产物的热稳定性明显优于PHB ,热分解温度提高了 2 0余度 ;结晶行为发生很大的变化 .结晶速率减小 ,结晶温度降低 ,冷结晶温度升高 ,球晶的织态结构也随着MA接枝量的变化发生明显变化 ,并且接枝MA促进了PHB的生物降解

官能化聚烯烃弹性体增韧PA1010体系Ⅱ.结晶行为的研究

用 WAXD、偏光显微镜 (PM)及 DSC研究了聚烯烃弹性体乙烯 - α-烯烃共聚物 (EOCP)对 PA10 10结晶行为的影响。WAXD结果显示纯弹性体 (EOCP)和接枝弹性体 (EOCP- g- MA)对 PA10 10的晶型均不产生影响。PM观察则表明共混体系中 EOCP与 PA10 10的相互作用很弱 ,在 PA10 10结晶过程中 ,大部分 EOCP被排除在球晶之外 ;而接枝 EOCP与 PA10 10存在较强的相互作用 ,大量的 EOCP- g- MA作为成核剂 ,使 PA10 10球晶向细晶化方向发展 ,而且随弹性体含量的增多而加强。DSC分析证实了接枝EOCP以异相成核剂的方式促进了 PA10 10的结晶 ,尤其是促进了 PA10 10的高温结晶

Gas-phase Ion-molecular Reactions of C-60 and C-70 with Acetone and Quantum Chemistry Study

Gas-phase ion-molecular reactions of C-60 and C-70 with the ion system of acetone have been studied in this paper. The ions of protoned and acetylized C-60 and C-70 were formed by the reactions of C-60 and C-70 with some ions which existed in the ion system when mass spectrometer worked on chemical ionization conditions. The reactivity of C-70 is greater than that of C-60. Results of quantum chemical calculation for the adduct ions showed a sigma bond between the acyl carbon atom and C-60 may be Formed. These results will provide some valuable informations on the condense-phase acetylization of C-60.

Identification of 27 Porphyra lines (Rhodophyta) by DNA fingerprinting and molecular markers

Twenty-seven Porphyra lines, including lines widely used in China, wild lines and lines introduced to China from abroad in recent years, were screened by random amplified polymorphic DNA (RAPD) technique with 120 operon primers. From the generated RAPD products, 11 bands that showed stable and repeatable RAPD patterns amplified by OPC-04, OPJ-18 and OPX-06, respectively were scored and used to develop the DNA fingerprints of the 27 Porphyra lines. Moreover, the DNA fingerprinting patterns were converted into computer language expressed with two digitals, 1 and 0, which represented the presence (numbered as 1) or absence (numbered as 0) of the corresponding band, respectively. Based on the above results, computerized DNA fingerprints were constructed in which each of the 27 Porphyra lines has its unique fingerprinting pattern and can be easily distinguished from others. Software named PGI (Porphyra germplasm identification) was designed for identification of the 27 Porphyra lines. In addition, seven specific RAPD markers from seven Porphyra lines were identified and two of them were successfully converted into SCAR (sequence characterized amplification region) markers. The developed DNA fingerprinting and specific molecular markers provide useful ways for the identification, classification and resource protection of the Porphyra lines.

SYNTHESIS AND CRYSTALLIZATION BEHAVIOR OF (PP-MA)-G-PEO

A new graft copolymer (PP-MA)-g-PEO was synthesized by means of the chemical reaction between maleated polypropylene (PP-MA) and mono hydroxyl poly(ethylene oxide) (PEO-OH). The effect of reaction conditions on the degree of grafting of PEO-OH was studied

G蛋白在松类植物花粉管发育中的亚细胞定位及调控机制

G蛋白参与了哺乳动物内多种细胞信号途径，但其在植物花粉萌发和花粉管发育过程中的细胞学定位、生化特性及功能研究比较滞后，有关这方面的研究报道较少。在显花植物授粉受精过程中，具顶端极性生长特性的花粉管是雄性生殖单位的载体，也是研究细胞生长分子调控机理的理想体系。与被子植物相比，裸子植物具有生长周期长，花粉管生长缓慢、易分叉等特点，具有不同于被子植物花粉发育的独特发育模式。对于裸子植物花粉萌发和花粉管生长的调控机理，目前尚不十分清楚。本文以松类植物中比较有代表性的裸子植物青杆（Piceawillsonii）和白皮松(Pinus bungeana)花粉为试材，应用免疫分析和间接免疫荧光显微镜技术，结合药理学实验和FTIR手段，研究了异三聚体G蛋白和小G蛋白在花粉管细胞中的定位、生化特性及其在花粉管发育中的调控作用。结果如下： 应用Western Blotting技术和来自于抗哺乳动物中不同序列G蛋白O【亚基抗体，我们在白皮松花粉管中检测到一条分子量为40 kDa左右的蛋白。去污剂处理显示，该蛋白与质膜偶联。间接免疫荧光显微镜实验发现，在花粉管发育的整个时期，代表Ga蛋白的荧光均一的分布在整个质膜区域，尤其在尖端皮层区域荧光最亮，显示此处该蛋白浓度最高。无论是在正常发育的花粉管抑或是发生弯曲或扭曲生长的花粉管，均呈现同样的分布模式。随着花粉管发育，Ga蛋白表达量发生变化。在花粉管发育中期，Ga蛋白表达量比较高;随着花粉管离体培养时间的延长，Ga蛋白表达量下降。另外，在花粉刚刚萌发时，Ga蛋白表达量也比较低。 对白皮松花粉萌发进行的药理学实验显示，G蛋白调节剂 CTX和PTX对白皮松花粉管的影响呈现双阶段效应。当添加的药剂浓度小于400 ng mL-I时，无论CTX还是PTX均抑制了花粉萌发和花粉管生长，且花粉管容易破裂;而当二者浓度分别升至500 ng mL-I时，同对照相比，花粉管生长明显受到促进。这一结果不支持Ma等人在百合花粉中的研究结果。进一步应用FTIR技术分析发现，当用浓度为400 ng mL-I CTX或PTX处理花粉管时，花粉管细胞壁酚类物质增加，而纤维素、半纤维素、木聚糖等物质下降，这可能是导致此浓度处理下花粉管易破裂的原因。这些结果显示了G蛋白a亚基参与了白皮松花粉管生长，CTX和PTX可能通过下游对其敏感的功能蛋白而非Ga本身，影响着花粉管生长并调控着花粉管壁的建成。 利用来源于烟草的抗NtRacl抗体和拟南芥的抗ROPs抗体，应用WeternBlotting技术，我们在青杆花粉管中检测到分子量为23kDa的多肽。间接免疫荧光显微镜实验显示，在花粉萌发18和24小时后，Rac蛋白主要定位于花粉管尖端质膜区域，时而会延伸到顶端两侧区域，但从尖端到基部存在浓度梯度，这种分布模式多在花粉管发育的后期观察到。Rac蛋白在青杆花粉管不同发育时期的分布模式变化可能和花粉管的生长状态有关，在花粉管发育早期和中期，正是花粉管旺盛生长期，Rac蛋白的尖端定位保证了花粉管的极性生长。对Rac蛋白在花粉管的分布进行的连续切片扫描发现，Rac蛋白不但分布在质膜上，并与质膜偶联，而且在胞质中亦有分布。通过对一系列正常发育（即极性生长的花粉管）和畸形发育的花粉管进行观察发现，Rac蛋白主要分布在旺盛生长的花粉管尖端质膜或离顶端20 Vm处，在分叉的生长缓慢的分枝端分布较少。而在那些发生分叉生长的花粉管中，处于次要位置的基本停止生长的分枝端几乎没有Rac蛋白存在。在顶端发生膨大的花粉管中，Rac蛋白均匀分布在花粉管整个质膜上，丧失浓度梯度，失去极性生长。这些结果显示了Rac蛋白参与了青杆花粉管生长。 应用抗NtRacl抗体进行的间接免疫荧光显微镜定位实验，我们在正在生长的花粉管的管核中观察到明亮的荧光，显示了有Rac蛋白的存在。当精细胞在花粉粒中未移动到花粉管中时，几乎没有观察到荧光信号。随着花粉管发育，两个精细胞的位置发生变化，当其中一个较大的精细胞移动到花粉管中时，观察到明亮的荧光信号，这些结果显示了Rac蛋白可能参与了管核或精细胞在花粉管内的移动。