High Aspect Ratio (L/D) Riser Viv Prediction Using Wake Oscillator Model

A two-dimensional (2-D) vortex-induced vibration (VIV) prediction model for high aspect ratio (LID) riser subjected to uniform and sheared flow is studied in this paper. The nonlinear structure equations are considered. The near wake dynamics describing the fluctuating nature of vortex shedding is modeled using classical van der Pol equation. A new approach was applied to calibrate the empirical parameters in the wake oscillator model. Compared the predicted results with the experimental data and computational fluid dynamic (CFD) results. Good agreements are observed. It can be concluded that the present model can be used as simple computational tool in predicting some aspects of VIV of long flexible structures. (C) 2008 Elsevier Ltd. All rights reserved.

An Electrowetting Model For Rough Surfaces Under Low Voltage

Electrowetting is one of the most effective methods to enhance wettability. A significant change of contact angle for the liquid droplet can result from the surface microstructures and the external electric field, without altering the chemical composition of the system. During the electrowetting process on a rough surface, the droplet exhibits a sharp transition from the Cassie-Baxter to the Wenzel regime at a low critical voltage. In this paper, a theoretical model for electrowetting is put forth to describe the dynamic electrical control of the wetting behavior at the low voltage, considering the surface topography. The theoretical results are found to be in good agreement with the existing experimental results. (c) Koninklijke Brill NV, Leiden, 2008.

A generalized model for the effective thermal conductivity of porous media based on self-similarity

A generalized model for the effective thermal conductivity of porous media is derived based on the fact that statistical self-similarity exists in porous media. The proposed model assumes that porous media consist of two portions: randomly distributed non-touching particles and self-similarly distributed particles contacting each other with resistance. The latter are simulated by Sierpinski carpets with side length L = 13 and cutout size C = 3, 5, 7 and 9, respectively, depending upon the porosity concerned. Recursive formulae are presented and expressed as a function of porosity, ratio of areas, ratio of component thermal conductivities and contact resistance, and there is no empirical constant and every parameter has a clear physical meaning. The model predictions are compared with the existing experimental data, and good agreement is found in a wide range of porosity of 0.14-0.80, and this verifies the validity of the proposed model.

Fractal geometry model for effective thermal conductivity of three-phase porous media

An approximate model, a fractal geometry model, for the effective thermal conductivity of three-phase/unsaturated porous media is proposed based on the thermal-electrical analogy technique and on statistical self-similarity of porous media. The proposed thermal conductivity model is expressed as a function of porosity (related to stage n of Sierpinski carpet), ratio of areas, ratio of component thermal conductivities, and saturation. The recursive algorithm for the thermal conductivity by the proposed model is presented and found to be quite simple. The model predictions are compared with the existing measurements. Good agreement is found between the present model predictions and the existing experimental data. This verifies the validity of the proposed model. (C) 2004 American Institute of Physics.

A dynamic coupling model for hybrid atomistic-continuum computations

A dynamic coupling model is developed for a hybrid atomistic-continuum computation in micro- and nano-fluidics. In the hybrid atomistic-continuum computation, a molecular dynamics (MD) simulation is utilized in one region where the continuum assumption breaks down and the Navier-Stokes (NS) equations are used in another region where the continuum assumption holds. In the overlapping part of these two regions, a constrained particle dynamics is needed to couple the MD simulation and the NS equations. The currently existing coupling models for the constrained particle dynamics have a coupling parameter, which has to be empirically determined. In the present work, a novel dynamic coupling model is introduced where the coupling parameter can be calculated as the computation progresses rather than inputing a priori. The dynamic coupling model is based on the momentum constraint and exhibits a correct relaxation rate. The results from the hybrid simulation on the Couette flow and the Stokes flow are in good agreement with the data from the full MD simulation and the solutions of the NS equations, respectively. (c) 2007 Elsevier Ltd. All rights reserved.

Determination of plastic properties by instrumented spherical indentation: Expanding cavity model and similarity solution approach

The present paper aims to develop a robust spherical indentation-based method to extract material plastic properties. For this purpose, a new consideration of-piling-up effect is incorporated into the expanding cavity model; an extensive numerical study on the similarity Solution has also been performed. As a consequence, two semi-theoretical relations between the indentation response and material plastic properties are derived, with which plastic properties of materials can be identified from a single instrumented spherical indentation curve, the advantage being that this approach no longer needs estimations of contact radius with given elastic modulus. Moreover, the inconvenience in using multiple indenters with different tip angles can be avoided. Comprehensive sensitivity analyses show that the present algorithm is reliable. Also, by experimental verification performed oil three typical materials, good agreement of the material properties between those obtained from the reverse algorithm and experimental data is obtained.

Determination Of Plastic Properties By Instrumented Spherical Indentation: Expanding Cavity Model And Similarity Solution Approach

The present paper aims to develop a robust spherical indentation-based method to extract material plastic properties. For this purpose, a new consideration of-piling-up effect is incorporated into the expanding cavity model; an extensive numerical study on the similarity Solution has also been performed. As a consequence, two semi-theoretical relations between the indentation response and material plastic properties are derived, with which plastic properties of materials can be identified from a single instrumented spherical indentation curve, the advantage being that this approach no longer needs estimations of contact radius with given elastic modulus. Moreover, the inconvenience in using multiple indenters with different tip angles can be avoided. Comprehensive sensitivity analyses show that the present algorithm is reliable. Also, by experimental verification performed oil three typical materials, good agreement of the material properties between those obtained from the reverse algorithm and experimental data is obtained.

Primary cultured cells as sensitive in vitro model for assessment of toxicants-comparison to hepatocytes and gill epithelia

In an effort to develop cultured cell models for toxicity screening and environmental biomonitoring, we compared primary cultured gill epithelia and hepatocytes from freshwater tilapia (Oreochromis niloticus) to assess their sensitivity to AhR agonist toxicants. Epithelia were cultured on permeable supports (terephthalate membranes, "filters") and bathed on the apical with waterborne toxicants (pseudo in vivo asymmetrical culture conditions). Hepatocytes were cultured in multi-well plates and exposed to toxicants in culture medium. Cytochrome P4501A (measured as 7-Ethoxyresorufin-O-deethylase, EROD) was selected as a biomarker. For cultured gill epithelia, the integrity of the epithelia remained unchanged on exposure to model toxicants, such as 1,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD), benzo(a)pyrene B[a]P, polychlorinated biphenyl (PCB) mixture (Aroclor 1254), and polybrominated diphenyl ether (PBDE) mixture (DE71). A good concentration-dependent response of EROD activity was clearly observed in both cultured gill epithelia and hepatocytes. The time-course response of EROD was measured as early as 3 h, and was maximal after 6 h of exposure to TCDD, B [alp and Aroclor 1254. The estimated 6 h EC50 for TCDD, B [a]P, and Aroclor 1254 was 1.2x10(-9), 5.7x10(-8) and 6.6x10(-6) M. For the cultured hepatocytes, time-course study showed that a significant induction of EROD took place at 18 h, and the maximal induction of EROD was observed at 24 h after exposure. The estimated 24 It EC50 for TCDD, B[a]P, and Aroclor 1254 was 1.4x10(-9), 8.1x10(-8) and 7.3x10(-6) M. There was no induction or inhibition of EROD in DE71 exposure to both gill epithelia and hepatocytes. The results show that cultured gill epithelia more rapidly induce EROD and are slightly more sensitive than cultured hepatocytes, and could be used as a rapid and sensitive tool for screening chemicals and monitoring environmental AhR agonist toxicants. (c) 2006 Elsevier B.V. All rights reserved.

Carrier transport properties of the (n)nc-Si : H/(p)c-Si heterojunction

Phosphor-doped nano-crystalline silicon ((n))nc-Si:H) films are successfully grown on the p-type (100) oriented crystal silicon ((p) c-Si) substrate by conventional plasma-enhanced chemical vapor deposition method. The films are obtained using high H-2 diluted SiH4 as a reaction gas source and using PH3 as the doping gas source of phosphor atoms. Futhermore, the heterojunction diodes are also fabricated by using (n)nc-Si:H films and (p)c-Si substrate. I-V properties are investigated in the temperature range of 230-420K. The experimental results domenstrate that (n)nc-Si:H/(p) c-Si heterojunction is a typical abrupt heterojunction having good rectifing and temperature properties. Carrier transport mechanisms are tunneling - recombination model at forward bias voltages. In the range of low bias voltages ( V-F< 0.8 V), the current is determined by recombination at the (n)nc-Si:H side of the space charge region, while the current becomes tunneing at higher bias voltages( V-F>1.0 V). The present heterojunction has high reverse breakdown voltage ( > - 75 V) and low reverse current (approximate to nA).

吲哚生物碱Desbromoarborescidine A 的全合成及烯胺C-亚磺酰化反应研究

从新几内亚核桃木的树皮中分离得到的吲哚类喹诺里西定生物碱10-Desbromoarborescidine A，因发现其具有阻滞钙离子通道的活性而倍受关注。10-Desbromoarborescidine A由A、B、C、D四个环组成，只有一个手性中心，是吲哚生物碱中结构较简单的一种，常作为此类生物碱全合成方法的模型化合物。但迄今为止，能高效而简便的实现手性10-Desbromoarborescidine A不对称全合成方法线路不多，大多数以不对称诱导的方式建立其手性中心，手性催化的方式仅有一例金属催化。从逆合成分析可知，Desbromoarborescidine A的全合成可以通过亚胺不对称催化还原进行关键的手性中心构建，而本课题组在之前的研究中通过手性有机小分子催化剂的发展，已将三氯硅烷氢转移还原亚胺发展成了一类简便实用、高效、高对映选择性并具有优良底物适应范围的不对称催化反应，我们希望以这一反应作为关键手段，发展一条Desbromoarborescidine A及其类似物不对称合成新路线。 根据我们设计的新路线，首先成功合成了其关键中间体，然后我们进行了关键的不对称催化尝试。用本实验室已有的高性能有机小分子催化剂虽得到了较好的对应选择性，但是产率很低。同时，为了验证整条线路的可行性，我们也用消旋的中间体进行拉通线路的尝试。但不幸的是，在脱除保护基时遇到了很大困难。尝试换不同的保护基，或改变脱保护基的顺序，都未能成功合成目标产物。究其原因可能是由于吲哚的特殊性造成的，吲哚类亚胺与常规的芳香亚胺有较大的差异，其NH基团无论保护还是不保护，对与其2位相联接的C=N双键均有很大的影响，导致其不对称催化还原难以进行。另外，由于所设计的还原产物含有处在吲哚苄位的胺基，稳定性较差，造成保护基脱除困难。 烯胺C-亚磺酰化反应是本课题组最近发现的一个新反应，之前未见文献报道。本研究对该反应进行了反应条件优化和底物扩展，发现带Cbz，Ac，COt-Bu，CO2Et，Bz等保护基的一系列环状和非环状烯胺在亚磺酸钠、DMAc和MeSiCl3的共同作用下能高效高产率生成β-胺基烯基亚砜类新化合物，为合成多官能团化的烯基亚砜新化合物提供了一条简便实用的途径。 The main constituent of Dracontomelum mangiferum B1, indoloquinolizidine alkaloid 10-Desbromoarborescidine A, has drawn great attention due to its calcium channel blocking activity. Its molecular structure is relatively simple compared with the other alkaloids of the same type, which has only one chiral center, albeit with four cycles A, B, C, and D. This compound is often used as a model target for exploring different strategies for the total synthesis of indole alkaloids. Nevertheless, so far there still lack practical and highly efficient methods for the asymmetric total synthesis of 10-Desbromoarborescidine A. Most of the current available methods rely on stoichiometric asymmetric synthesis for the construction of the chiral center. There is only one example reporting utilization of asymmetric catalysis, but with transition metal complex as the catalyst. Our retrosynthetic analysis shows that catalytic asymmetric reduction of imine could be used as the key step for the construction of the chiral center of Desbromoarborescidine A. Since in the previous studies our group has developed the asymmetric reduction of imines by trichlorosilane into a practical and highly efficient and enantioselective method using newly designed chiral organocatalysts, we hope to apply this method to develop a novel synthetic route for the total synthesis of Desbromoarborescidine A and its analogues in this study. According to the newly designed synthetic route, we first accomplished the synthesis of the key intermediates which was then examined for the critical asymmetric catalysis. The asymmetric reduction using the highly efficient organocatalysts, developed in our lab afforded high ee but poor yield. We tried different reaction conditions to improve the yield, but failed to get any good results. Simultaneously, to vertify the feasibility of the synthetic route we designed, we also tired to go through the route toward the racemic synthesis of Desbromoarborescidine A. But unfortunately, protection and deprotection proved to be big hurdles. All the different protection groups and different sequences of protection and deprotection we tried failed to get us through the designed synthetic sequence and furnish the final product. Most likely, the indole part is the culprit behind the failures.The NH group of the indole, no matter protected or not, may impact the catalytic asymmetric reduction of C-N double bond connected with 2-C. Additionally, the reduction product we designed contains an amino group in the β-position of the indole, which may cause problems due to its instability. C-sulfenylation of enamines is a novel reaction discovered recently by our group, which has not been seen before in the literature. In this study, optimization of the reaction conditions and exploration of the substrate scope were further undertaken for this reaction, which reveal that a series of enamines with N-Cbz, Ac, COt-Bu, CO2Et protection groups could all undergo smooth C-sulfinylations with the comined use of sodium benzene sulphinate, DAMc and MeSiCl3, efficiently furnishing the β-amino vinylsulfoxide products in high yield, affording a practical and highly efficient methods for synthesis of functional vinylsulfoxides.

Theoretical Analysis and New Formulae for Half-Lives of Proton Emission

The proton radioactivity half-lives of spherical proton emitters are calculated by the cluster model with the contribution of a centrifugal potential barrier considered separately. The results are compared with the experimental data and other theoretical data, and good agreement is found for most nuclei. In addition, two formulae are proposed for the proton decay half-life of spherical proton emitters through the least squares fit to the experimental data available, and could reproduce the experimental half-lives successfully.

Shell-model Hamiltonian from self-consistent mean-field model: N = Z nuclei

We propose a procedure to determine the effective nuclear shell-model Hamiltonian in a truncated space from a self-consistent mean-field model, e.g., the Skyrme model. The parameters of pairing plus quadrupole-quadrupole interaction with monopole force are obtained so that the potential energy surface of the Skyrme Hartree-Fock + BCS calculation is reproduced. We test our method for N = Z nuclei in the fpg- and sd-shell regions. It is shown that the calculated energy spectra with these parameters are in a good agreement with experimental data, in which the importance of the monopole interaction is discussed. This method may represent a practical way of defining the Hamiltonian for general shell-model calculations. (C) 2009 Elsevier B.V. All rights reserved.

alpha-decay half-lives of superheavy nuclei and general predictions

The generalized liquid drop model (GLDM) and the cluster model have been employed to calculate the alpha-decay half-lives of superheavy nuclei (SHN) using the experimental alpha-decay Q values. The results of the cluster model are slightly poorer than those from the GLDM if experimental Q values are used. The prediction powers of these two models with theoretical Q values from Audi et al. (Q(Audi)) and Muntian et al. (Q(M)) have been tested to find that the cluster model with Q(Audi) and Q(M) could provide reliable results for Z > 112 but the GLDM with Q(Audi) for Z <= 112. The half-lives of some still unknown nuclei are predicted by these two models and these results may be useful for future experimental assignment and identification.

Alpha decay half-lives of new superheavy elements through quasimolecular shapes

The lifetimes of alpha decays of the recently produced isotopes of the elements 112, 114, 116 and the element (294)118 and of some decay products have been calculated theoretically within the Wentzel-Kramers-Brillouin approximation. The alpha decay barriers have been determined in the quasimolecular shape path within a generalized liquid drop model including the proximity effects between nuclei in a neck, the mass and charge asymmetry and the precise nuclear radius. These calculations provide reasonable estimated for the observed alpha decay lifetimes. The calculated results have been compared with the results of the density-dependent M3Y effective interaction and the experimental data. It is indicated that the theoretical foundation of the generalized liquid drop model is as good as that of the microscopic DDM3Y model, at least in the sense of predicting the T-1/2 values as long as one uses a correct alpha decay energy. The half lives of these new nuclei are well tested from the consistence of the macroscopic, the microscopic and the experimental data.