PPLT倍频宽线宽掺镱双包层光纤放大激光

分别通过理论和实验研究了周期性极化的钽酸锂（PPLT）倍频宽线宽准连续掺镱双包层光纤放大激光．PPLT样品长为40mm，极化周期为7．67μm．基频光的中心波长为1064nm，线宽约为6nm。从基频光的光谱特性出发，利用超晶格倍频理论，解释了实验中获得的倍频温度与二次谐波功率之间的关系．在基频光的功率为2．2W时，获得的宽线宽光纤激光倍频效率为1．8％。

采用国产大模场面积双包层光纤的714W连续光纤激光器

采用两个中心波长约976nm准直输出的高功率半导体激光模块为抽运源，通过空间滤波和非球面透镜耦合技术，双端抽运长度为21m的大模场面积国产掺镱双包层光纤，获得了714．5W的高功率连续激光输出。采用反向抽运，当人纤抽运功率为760W时，激光输出功率达到501W；采用双端抽运，当人纤抽运功率为1137W时，获得了714．5W的高功率连续输出，光光转换效率为62．8％，斜率效率为67％。

7.3 W国产单频光纤放大器

报道了一种MOPA式国产单频光纤放大器。该放大器采用连续波单频激光器作为主振荡器，采用我国自行设计和制造的大模场面积掺Yb双包层光纤作为功率放大器，在波长1064 nm处实现了最高7.3 W的连续激光输出，斜率效率为39%，光－光转换效率为26%。此外，对光谱特性及放大的自发发射的抑制也进行了探讨。

双程掺镱光纤放大器的增益特征及优化

比较了掺钕光纤和掺镱光纤对1064nm光放大的特点．基于速率方程和传输方程，数值分析了在915nm泵浦下双程掺镱光纤放大器的增益特征，并且和传统的单程放大进行了比较．分析了信号光和泵浦光，以及粒子数沿着光纤方向的分布特点．最后对双程掺镱光纤放大器进行了优化．

高功率双包层光纤放大器

高功率双包层光纤放大器在光纤传感、光纤通讯、光谱测量和惯性约束聚变等领域有广泛应用。介绍了两种获得放大激光输出的高功率双包层光纤放大器：单频双包层光纤放大器和脉冲双包层光纤放大器。分析了它们的工作原理及关键技术，并对国内外近期进展作了综述。

种子光功率对脉冲双包层光纤放大器性能的影响

采用国产的大模场面积双包层光纤和(2+1)×1多模泵浦耦合器，研制出近衍射极限输出的MOPA式脉冲光纤放大器。基于该放大器，发现种子光输出平均功率对放大性能有一定的影响。在泵浦功率一定的情况下，为保证脉冲光纤放大器稳定可靠地运行，对种子光功率来讲，存在一个特定的取值范围。种子光输出平均功率70 mW时，对该脉冲光纤放大器的放大性能进行了研究。

Temperature and composition profile during double-track laser cladding of H13 tool steel

Multi-track laser cladding is now applied commercially in a range of industries such as automotive, mining and aerospace due to its diversified potential for material processing. The knowledge of temperature, velocity and composition distribution history is essential for a better understanding of the process and subsequent microstructure evolution and properties. Numerical simulation not only helps to understand the complex physical phenomena and underlying principles involved in this process, but it can also be used in the process prediction and system control. The double-track coaxial laser cladding with H13 tool steel powder injection is simulated using a comprehensive three-dimensional model, based on the mass, momentum, energy conservation and solute transport equation. Some important physical phenomena, such as heat transfer, phase changes, mass addition and fluid flow, are taken into account in the calculation. The physical properties for a mixture of solid and liquid phase are defined by treating it as a continuum media. The velocity of the laser beam during the transition between two tracks is considered. The evolution of temperature and composition of different monitoring locations is simulated.

A study of a Q-switched double-clad ytterbium-doped fiber laser with amplifying effect

A high repetition rate ytterbium-doped double-clad (YDDC) fiber laser with amplifying effect is described by using acousto-optic modulator. The characteristic of Q-switched pulses are studied with accurate control of opening gate time of modulator. The stable Q-switched pulses with tens of nanoseconds width can be observed at high repetition rate varied from 50 kHz to 500 kHz using this laser. The stable operation area of the Q-switched fiber laser is discussed and the analysis results agree well with that of the experiment. (c) 2007 Elsevier B.V. All rights reserved.

Fabrication and amplified spontaneous emission spectrum of Er3+-doped tellurite glass fiber with D-shape cladding

Tellurite glass is proposed as a host for broadband erbium-doped fiber amplifiers because of their excellent optical and chemical properties. A single-mode Er3+-doped tellurite glass fiber with D-shape cladding was fabricated in this work. The characterization of amplified spontaneous emission (ASE) from this newly fabricated Er3+-doped tellurite fibers are exhibited. When pumped at 980 nm, a very broad erbium ASE nearly 150 nm around 1.53 mum is observed. The changes in ASE with regard to fiber lengths and pumping power were measured and discussed. The output of 2 mW from Er3+-doped tellurite fiber ASE source was obtained under the pump power of 660 mW. The broad 1.53 mum emission of Er3+ in tellurite glass fiber can be used as host material for potential broadband optical amplifier and tunable fiber lasers. (C) 2004 Elsevier B.V. All rights reserved.

Fiber laser hydrophone based on double diaphragms: Theory and experiment

A fiber laser hydrophone with enhanced sensitivity is demonstrated. Two diaphragms with a hard core fixed at each center are used as the sensing element. Theoretical analysis shows that the Young's modulus of the diaphragm and the radius of the hard core have significant effect on the acoustic sensitivity. Experiments are carried out to test this effect and the performance of the hydrophone. The experimental result agrees well with the theoretical result, and a sensitivity of 7 nm/MPa has been achieved.

Tuning the resonant wavelength of long period fiber gratings by etching the fiber's cladding

In this paper the resonant wavelength of a long period fiber grating (LPG) is tuned toward longer wavelength by etching the fiber, For LP04 and LP05 cladding modes', the tuning ranges of 23 and 81 nm are achieved, respectively. Also the dependence of the resonant wavelength on the cladding radius of LPG is theoretically simulated. (C) 2001 Elsevier Science B,V. All rights reserved.

PERFORMANCE OF DOUBLE SIDEBAND MODULATED PROBE WAVE IN BOTDA DISTRIBUTED FIBER SENSOR

We report on the performance of double sideband (DSB) modulated probe wave in Brillouin optical time domain analysis (BOTDA) distributed fiber sensor. Compared to single sideband (SSB)modulation, along the sensing fiber the pump depletion of DSB modulation is remarkably suppressed in time domain and also has a relatively narrower Brillouin gain spectrum in frequency domain. Both the theoretical simulation and the experimental results demonstrate that the DSB modulation provides potentially longer sensing distance and higher accuracy in measurement than the SSB modulation in the BOTDA distributed fiber sensor system.

The interlaminar fracture-behavior and toughening mechanisms of new carbon-fiber-reinforced bismaleimide composites

The interlaminar fracture behaviour of carbon fibre-reinforced bismaleimide (BMI) composites prepared by using a new modified BMI matrix has been investigated by various methods. Laminates of three typical stacking sequences were evaluated. Double cantilever beam, end-notch flexure and edge-delamination tension tests were conducted under conventional conditions and in a scanning electron microscope. The strain energy release rates in Mode I and Mode III G(lc) and G(llc), as well as the total strain energy release rate, G(mc), have been determined and found to be higher than those for laminates with an epoxy matrix. Dynamic delamination propagation was also studied. The toughening mechanisms are discussed.