High transmission of slow light in the photonic crystal waveguide bends

We present the research on the transmission characteristic of slow-light-mode in the photonic crystal line-defect waveguide bends on SOL After optimizing the structure parameters in the vicinity of the bends, the normalized transmission efficiency of slow-light-mode through the photonic crystal 60 degree and 120 degree waveguide bends are as high as 80% and 60% respectively, which are 10 times higher than that in the undeformed case. To slow down light further, we design novel coupled cavity waveguide bend structures with high quality-factor. High normalized transmission efficiency of 75% and low group velocity of c/170 ( c is the light velocity in vacuum) are realized. These results are beneficial to enhance the slow light effect of photonic crystal structures and improve the miniaturization and integration of photonic crystal slow light devices.

Flexible Control of Light Propagation Using a Novel Photonic Crystal Hetero-Waveguide Based on Silicon-on-Insulator Slab

We demonstrate a photonic crystal hetero-waveguide based on silicon-on-insulator (SOI) slab, consisting of two serially connected width-reduced photonic crystal waveguides with different radii of the air holes adjacent to the waveguide. We show theoretically that the transmission window of the structure corresponds to the transmission range common to both waveguides and it is in inverse proportion to the discrepancy between the two waveguides. Also the group velocity of guided mode can be changed from low to high or high to low, depending on which port of the structure the signal is input from just in the same device, and the variation is proportional to the discrepancy between the two waveguides. Using this novel structure, we realize flexible control of transmission window and group velocity of guided mode simultaneously.

High efficiency operation of butt joint line-defect-waveguide microlaser in two-dimensional photonic crystal slab

Butt joint line-defect-waveguide microlasers are demonstrated on photonic crystal slabs with airholes in a triangular lattice. Such microlaser is designed to increase the output power from the waveguide edge directly. The output power is remarkably enhanced to 214 times higher by introducing chirped structure in the output waveguide. The lasing mode operates in the linear dispersion region of the output waveguide so that the absorption loss due to the band-edge effect is reduced. The laser resonance is illustrated theoretically using the finite difference time domain method. A practical high power efficiency of 20% is obtained in this microlaser. (C) 2008 American Institute of Physics.

Finite element beam propagation method for analysis of plasmonic waveguide

The basic idea of the finite element beam propagation method (FE-BPM) is described. It is applied to calculate the fundamental mode of a channel plasmonic polariton (CPP) waveguide to confirm its validity. Both the field distribution and the effective index of the, fundamental mode are given by the method. The convergence speed shows the advantage and stability of this method. Then a plasmonic waveguide with a dielectric strip deposited on a metal substrate is investigated, and the group velocity is negative for the fundamental mode of this kind of waveguide. The numerical result shows that the power flow direction is reverse to that of phase velocity.

Simulation demonstration and experimental fabrication of a multiple-slot waveguide

A multiple-slot waveguide is presented and demonstrated through theoretical simulation. Taking a double-slot waveguide as an example, the results show a nearly 30% enhancement of optical intensity compared with the traditional single-slot waveguide with the same slot gap width. Therefore, the E-field intensity of the slot can be increased by adding another smaller slot. A double-slot waveguide with oxide and air as low index slot materials is realized experimentally and the formation processes of the slots are analyzed.

A ministop band in a single-defect photonic crystal waveguide based on silicon on insulator

This paper reports that a two-dimensional single-defect photonic crystal waveguide in the F-K direction with triangular lattice on a silicon-on-insulator substrate is fabricated by the combination of electron beam lithography and inductively coupled plasma etching. A ministop band (MSB) is observed by the measurement of transmission characteristics. It results from the coupling between the two modes with the same symmetry, which is analysed from the stimulated band diagram by the effective index and the two-dimensional plane wave expansion methods. The parameter working on the MSB is the ratio of the radius of air holes to the lattice constant, r/a. It is obtained that the critical r/a value determining the occurrence or disappearance of MSB is 0.36. When r/a is larger than or equal to 0.36, the MSB occurs. However, when r/a is smaller than 0.36, the MSB disappears.

Spin current diode based on an electron waveguide with spin-orbit interaction

We propose a spin current diode which can work even in a small applied bias condition (the linear-response regime). The prototypal device consists of a hornlike electron waveguide with Rashba spin-orbit interaction, which is connected to two leads with different widths. It is demonstrated that when electrons are incident from the narrow lead, the generated spin conductance fluctuates around a constant value in a wide range of incident energy. When the transport direction is reversed, the spin conductance is suppressed strongly. Such a remarkable difference arises from spin-flipped transitions caused by the spin-orbit interaction. (c) 2008 American Institute of Physics.

Numerical study of sub-wavelength plasmonic waveguide

The authors present an analysis of a plasmonic waveguide, simulated using a two-dimensional finite-difference time-domain technique. With the surface structures located on the surface of the metal, the device is able to confine and guide light waves in a sub-wavelength scale. And two waveguides can be placed within 150 nm (similar to 6% of the incident wavelength) that will helpful for the optoelectronic integration. Within the 20 mu m simulation region, it is found that the intensity of the guided light at the interface is roughly two to four times the peak intensity of the incident light, and the propagation length can reach approximately 40 Pm at the wavelength of 2.44 mu m. (c) 2007 Elsevier B.V. All rights reserved.

Monolithically integrated transceiver with novel Y-branch by bundle integrated waveguide for fibre optic gyroscope

A novel Y-branch based monolithic transceiver with a superluminescent diode and a waveguide photodiode (Y-SDL-PD) is designed and fabricated by the method of bundle integrated waveguide (BIG) as the scheme for monolithic integration and angled Y-branch as the passive bi-directional waveguide. The simulations of BIG and Y-branches show low losses and improved far-field patterns, based on the beam propagation method (BPM). The amplified spontaneous emission of the device is up to 10mW at 120mA with no threshold and saturation. Spectral characteristics of about 30 nm width and less than 1 dB modulation are achieved using the built-in anti-lasing ability of Y-branch. The beam divergence angles in horizontal and vertical directions are optimized to as small as 12 degrees x 8 degrees, resulting in good fibre coupling.

Silicon waveguide modulator based on carrier depletion in periodically interleaved PN junctions

We present the design and numerical simulation results for a silicon waveguide modulator based on carrier depletion in a linear array of periodically interleaved PN junctions that are oriented perpendicular to the light propagation direction. In this geometry the overlap of the optical waveguide mode with the depletion region is much larger than in designs using a single PN junction aligned parallel to the waveguide propagation direction. Simulations predict that an optimized modulator will have a high modulation efficiency of 0.56 V.cm for a 3V bias, with a 3 dB frequency bandwidth of over 40 GHz. This device has a length of 1.86 mm with a maximum intrinsic loss of 4.3 dB at 0V bias, due to free carrier absorption. (C) 2009 Optical Society of America

Integration of a photonic crystal polarization beam splitter and waveguide bend

In this work, we present the design of an integrated photonic-crystal polarization beam splitter (PC-PBS) and a low-loss photonic-crystal 60 waveguide bend. Firstly, the modal properties of the PC-PBS and the mechanism of the low-loss waveguide bend are investigated by the two-dimensional finite-difference time-domain (FDTD) method, and then the integration of the two devices is studied. It shows that, although the individual devices perform well separately, the performance of the integrated circuit is poor due to the multi-mode property of the PC-PBS. By introducing deformed airhole structures, a single-mode PC-PBS is proposed, which significantly enhance the performance of the circuit with the extinction ratios remaining above 20dB for both transverse-electric (TE) and transverse-magnetic (TM) polarizations. Both the specific result and the general idea of integration design are promising in the photonic crystal integrated circuits in the future. (C) 2009 Optical Society of America

Resonant Enhanced Wave Filter and Waveguide via Surface Plasmons

The authors present an analysis of plasmonic wave filter and curved waveguide, simulated using a 2-D finite-difference time-domain technique. With different dielectric materials or surface structures located on the interface of the metal/dielectric, the resonant enhanced wave filter can divide light waves of different wavelengths and guide them with low losses. And the straight or curved waveguide can confine and guide light waves in a subwavelength scale. Within the 20 mu m simulation region, it is found that the intensity of the guided light at the interface is roughly four times the peak intensity of the incident light.

Four-channel reconfigurable optical add-drop multiplexer based on photonic wire waveguide

We designed and fabricated a four-channel reconfigurable optical add-drop multiplexer based on silicon photonic wire waveguide controlled through thermo-optic effect. The effective footprint of the device is about 1000 x 500 mu m(2). The minimum insertion loss is about 10.7 dB and the tuning bandwidth about 17 nm. The average tuning power efficiency is about 6.187 mW/nm and the tuning speed about 24.4 kHz. The thermo-optic polarization-rotation effect is firstly reported in this paper. (C) 2009 Optical Society of America

Wavelength conversion based on degenerate-four-wave-mixing with continuous-wave pumping in silicon nanowire waveguide

We present a comprehensive numerical study on the all-optical wavelength conversion based on the degenerate four-wave-mixing with continuous-wave pumping in the silicon nanowire waveguide. It is well known that the conversion efficiency and the 3-dB bandwidth can be greatly affected by the phase-matching condition. Through proper design of the waveguide cross-section, its dispersion property can be adjusted to satisfy the phase-matching condition and therefore effective wavelength conversion can be achieved in a large wavelength range. Generally, the group velocity dispersion plays a dominant role in the wavelength conversion. However, the fourth-order dispersion takes an important effect on the wavelength conversion when the group velocity dispersion is near the zero-point. Furthermore, the conversion efficiency and the 3-dB bandwidth can also be affected by the interactive length and the initial pump power. Through the numerical simulation, the optimal values for the interactive length and the initial pump power, which are functions of the propagation loss, are obtained to realize the maximum conversion efficiency. (C) 2008 Elsevier B.V. All rights reserved.

Novel triplexing-filter design using silica-based direction coupler and an arrayed waveguide grating

A new triplexing filter based on a silica direction coupler and an arrayed waveguide grating is presented. Using a combination of a direction coupler and an arrayed waveguide grating, a 1310-nm channel is multiplexed and 1490- and 1550-nm channels are demultiplexed for fiber-to-the-home. The direction coupler is used to coarsely separate the 1310-nm channel from the 1490- and 1550-nm channels. Subsequently, an arrayed waveguide grating is used to demultiplex the 1490- from 1550-nm channel. The simulated spectra show the 1-dB bandwidth of 110 nm for the 1310-nm channel and 20 and 20.5 nm for the 1490- and 1550-nm channels. The insertion loss is only 0.15 dB for 1310 nm and 5 dB for 1490 and 1550 nm. The crosstalk between the 1490- and 1550-nm channels was less than -35 dB. (C) 2009 Society of Photo-Optical Instrumentation Engineers. [DOI 10.1117/1.3065508]