A 2-kW COIL with a square pipe-array JSOG and nitrogen buffer gas

A 2-kW-class chemical oxygen-iodine laser (COIL) using nitrogen buffer gas has been developed and tested since industrial applications of COIL devices will require the use of nitrogen as the buffer gas. The laser, with a gain length of 11.7 cm, is energized by a square pipe-array jet-type singlet oxygen generator (SPJSOG) and employs a nozzle bank with a designed Mach number of 2.5. The SPJSOG has advantages over the traditional plate-type JSOG in that it has less requirements on basic hydrogen peroxide (BHP) pump, and more important, it has much better operational stability. The SPJSOG without a cold trap and a gas-liquid separator could provide reliable operations for a total gas flow rate up to 450 mmol/s and with a low liquid driving pressure of around 0.7 atm or even lower. The nozzle bank was specially designed for a COIL using nitrogen as the buffer gas. The cavity was designed for a Mach number of 2.5, in order to provide a gas speed and static temperature in the cavity similar to that for a traditional COIL with helium buffer gas and a Mach 2 nozzle. An output power of 2.6 kW was obtained for a chlorine flow rate of 140 mmol/s, corresponding to a chemical efficiency of 20.4%. When the chlorine flow rate was reduced to 115 mmol/s, a higher chemical efficiency of 22.7% was attained. Measurements showed that the SPJSOG during normal operation could provide a singlet oxygen yield Y greater than or equal to 55%, a chlorine utilization U greater than or equal to 85%, and a relative water vapor concentration w = [H2O]/([O-2] + [Cl-2]) less than or equal to 0.1.

In situ chlorinating-graft copolymerization on isotactic polypropylene in gas-solid phase

A novel method in situ chlorinating-graft copolymerization (ISCGC) of grafting maleic anhydride (MAH) on isotactic polypropylene (iPP) in gas-solid phase was investigated in this paper. Chlorine (Cl-2) was used as initiator, chlorinating agent and termination agent at the same time during the reaction. The iPP was chlorinated as well as grafted with MAH in the reaction process. The product with chlorine and MAH in the same molecule was named as PP-cg-MAH. Existence of PP-cg-MAH was identified by Fourier transform infrared. Thermal behavior and crystallinity of PP-cg-MAH were analyzed by differential scanning calorimetry, X-ray diffraction and polarizing microscope. Influencing factors for the value of graft degree were also discussed. Compared with conventional peroxide initiated graft method, ISCGC revealed higher MAH graft efficiency (33%), and particularly alleviated degradation of iPP. iPP could be grafted successfully and without changing physical properties dramatically through this method.

Synthesis and characterization of the titanium complexes bearing two regioisomeric trifluoromethyl-containing enaminoketonato ligands and their behavior in ethylene polymerization

A series of new titanium complexes bearing two regioisomeric trifluoromethyl-containing enaminoketonato ligands (3a-h and 6a-h), [PhN=CRCHC(CF3)O](2)TiCl2 (3a, R = Me; 3b, R = n-C5H11; 3c, R = i-Pr; 3d, R = Cy; 3e, R = t-Bu; 3f, R = CH=CHPh; 3g, R = Et; 3h, R = n-C11H23) and [PhN=C(CF3)CHC(R)O](2)TiCl2 (6a, R = Ph; 6b, R = n-C5H11; 6c, R = i-Pr; 6d, R = Cy; 6e, R = t-Bu; 6f, R = CH=CHPh; 6g, R = CHPh2; 6h, R = CF3) have been synthesized and characterized. X-ray crystal structures analyses suggest that complexes 3c-e and 6c-d all adopt a distorted octahedral geometry around the titanium center. Complexes 3c, 3d and 6c display a cis-configuration of the two chlorine atoms around the titanium center, while complex 6d shows a trans-configuration of the two chlorine atoms. Especially, the configurational isomers (cis and trans) of complex 3e were identified both in solution and in the solid state by NMR and X-ray analyses. With modified methylaluminoxane as a cocatalyst, all the complexes are active towards ethylene polymerization, and produce high molecular weight polymers.

Ligand effect on the performance of organic light-emitting diodes based on europium complexes

A series of europium complexes were synthesized and their electroluminescent (EL) characteristics were studied. It was found by comparison that the different substituted groups, such as methyl, chlorine, and nitryl, on ligand 1,10-phenanthroline affect significantly the EL performance of devices based on these complexes. The more methyl-substituted groups on ligand 1,10-phenanthroline led to higher device efficiency. A chlorine-substituted group showed the approximate EL performance as two methyl-substituted groups, whereas a nitryl substituent reduced significantly the EL luminous efficiency. However, beta-diketonate ligand TTA and DBM exhibited similar EL performance. The improved EL luminous efficiency by proper substituted groups on the 1, 10-phenanthroline was attributed to the reduction of the energy loss caused by light hydrogen atom vibration, as well as concentration quenching caused by intermolecular interaction, and the match of energy level between the ligand and Eu3+.

Synthesis of asymmetric H-shaped block copolymer by the combination of atom transfer radical polymerization and living anionic polymerization

A new asymmetric H-shaped block copolymer (PS)(2)-PEO-(PMMA)(2) has been designed and successfully synthesized by the combination of atom transfer radical polymerization and living anionic polymerization. The synthesized 2,2-dichloro acetate-ethylene glycol (DCAG) was used to initiate the polymerization of styrene by ATRP to yield a symmetric homopolymer (Cl-PS)(2)-CHCCCCH2CH2OH with an active hydroxyl group. The chlorine was removed to yield the (PS)(2)-CHCOOCH2CH2OH ((PS)(2)-OH). The hydroxyl group of the (PS)(2)-OH, which is an active species of the living anionic polymerization, was used to initiate ethylene oxide by living anionic polymerization via DPMK to yield (PS)(2)-PEO-OH. The (PS)(2)-PEO-OH was reacted with the 2,2-dichloro acetyl chloride to yield (PS)(2)-PEO-OCCHCl2 ((PS)(2)-PEO-DCA). The asymmetric H-shaped block polymer (PS)(2)-PEO-(PMMA)(2) was prepared via ATRP of MMA at 130 degrees C using (PS)(2)-PEO-DCA as initiator and CuCl/bPy as the catalyst system. The architectures of the asymmetric H-shaped block copolymers, (PS)(2)-PEO-(PMMA)(2), were confirmed by H-1 NMR, GPC and Fr-IR.

Synthesis and crystal structure of bis(tetrahydrofurfurylindenyl) lanthanide chlorides

Lanthanocene chlorides (C4H7OCH2C9H6)(2)LnCl[Ln=Y(1); Ln=Gd(2)] were synthesized by the reaction of tetrahydrofurfurylindenyl lithium(in situ) with corresponding anhydrous lanthanide chorides in THF. The crystal structures of these two complexes were determined by X-ray diffraction and they were unsolvated monomeric complexes. They were stable in the air for several hours. Complexes 1 and 2 belong to the same crystal system (orthorhombic) and space group(P2(1)2(1)2(1)). The unit cell dimensions of complex 1 were a=1.042 52(9) nm, b=1.47455(12) nm, c=1.497 99(13) nm, Z=4, D-c=1.508 g/cm(3); The unit cell dimensions of complex 2 were a=1.037 01(10) nm, b=1.472 33(12) nm, c=1.513 54(14) nm, Z=4, D-c=1.699 g/cm(3). They have the same structure and different space configurations. The central metal atom is coordinated by two indenyl, two oxygen of the tetrahydrofurfuryl and one chlorine atom to form a distorted trigonal bipyramid.

Synthesis of substituted indenyl lanthanide chloride and molecular structure of [(C5H9C9H6)(2)Yb(mu-Cl)(2)Li(Et2O)(2)]

Reaction of anhydrous ytterbium trichlorides with 2 equiv. of cyclopentylindenyl lithium in THF solution, followed by removal of the solvent MO. crystallization of the product from diethyl ether, affords a crystal complex of the composition (C5H9C9H6)(2)Yb(mu-Cl)(2)Li(Et2O)(2). Crystallographic analysis shows that the ytterbium coordinated by two cyclopentylindenyl rings and lithium surrounded by two ether molecules are bridged by the two chlorine atoms and Yb, U and two chlorine atoms form a plane.

Synthesis and crystal structure of cyclopentylindene rare earth complex (C5H9C9H6)(3)SMCl-Li+ (THF)(4)

Rare earth complex (C5H9C9H6)(3)SmCl-Li+ (THF)(4)( I ) was synthesized by reacting anhydrous SmCl3 with two equivalents of C5H9C9H6Li. From mix-solvent of THF and hexane, red color single crystals were obtained. The crystal belongs to a cubic system, space group P2(1)3 with unit cell parameters a= b=c= 1. 754 0(2) nm, alpha=beta=gamma=90degrees, V=5. 396 4(11) nm(3), Z = 4. The ten-coordinated samarium atom is bonded to three cyclopentylindenyl rings and a chlorine atom to form the anionic part of the title complex, ring centroids and the chlorine atom form a tortured tetrahedron around samarium. In the cationic part, lithium atom coordinates to four oxygen atoms of THF molecules to form a normal tetrahedron. The Sm-C(within the same ring) distance varies from 0. 268 to 0. 299 nm.

Mass transfer of Er(III) between HBTMPTP dissolved in n-heptane and HAc-NaAc

The rate of extraction of Er(III) from aqueous acetate solutions at 0. 2 mol/L ionic strength by HBTMPTP in n-heptane was studied by using a constant interfacial area cell with laminar flow at (30+/- 0. 5)degrees C. The interfacial activity of HBTMPTP was investigated at n-heptane/0. 2 mol/L (H, Na)Ac (pH=5. 00) interface, The rate of Er(III) extraction was measured at different chemical compositions by varying hydrogen ion, HBTMPTP, Cyanex 302 and chlorine ion concentrations, The effect of stirring speed, temperature and special interfacial area on the rate of extraction was also studied. The results showed that, under the conditions of the experiments, the overall rate is diffusion controlled, that the impurities of Cyanex 302 have the effect of synergistic extraction.

Synthesis of bis [bis (tert-butylcyclopentadienyl) neodymium chloride] and structural trend of bis[bis(tertbutylcyclopentadienyl) lanthanide chloride]

The reaction of NdCl3 with 2 equiv. of Na-(BuC5H4)-C-t in THF(tetrahydrofuran) gives blue crystals [((BUC5H4)-C-t)(2)NdCl](2), C36H52Cl2Nd2(M-r = 844.11) Which crystallizes in the triclinic system with space group . The crystal data are a=11.978 (1), b=12.671(4), c=12.706(2)Angstrom, alpha=105.47(2), beta=99.38(1)? gamma=93.15 (2)degrees, V=1825 (3) Angstrom(3), Z = 2 , D-c = 1.53g/cm(3), F(000) = 450 , T = 298K , lambda(MoK alpha) = 0.71069 Angstrom, , mu = 14.97cm(-1). Final R = 0.0390, R-w = 0.0376 for 4329 reflections with I greater than or equal to 3 sigma(I-o). The molecule has a dimer structure with two certrosymmetrical chlorine bridges. The structural trend of these analogous complexes is discussed.

A novel epitaxy of isotactic polypropylene (alpha phase) on PTFE and organic substrates

Isotactic polypropylene in its a modification (alpha iPP) crystallises epitaxially on polytetrafluoroethylene (PTFE) and several hemiacids or salts of substituted benzoic acids via a novel contact plane, namely (110): so far, the only known contact plane involved in alpha iPP homo- and hetero-epitaxies was (010). In spite of its complicated architecture (alternation of antichiral helices with different azimuthal settings), the (110)(alpha iPP) contact plane displays well defined, if not prominent, rows of methyl side chains parallel to the crystallographic (112) direction (at 57 degrees to the c-axis) and approximate to 5.5 Angstrom apart. The matching contact planes of the substrates display linear gratings made of rows of e.g. chlorine atoms or PTFE chains with similar approximate to 5.5 Angstrom inter-row or interchain distances. Various morphologies are observed in iPP thin films crystallised at different cooling rates in the presence of PTFE; they can be analysed in terms of a succession and interplay of successive epitaxies: initial alpha iPP/PTFE heteroepitaxy, followed by alpha iPP/alpha iPP and gamma iPP/alpha iPP homoepitaxies. (C) 1999 Published by Elsevier Science Ltd. All rights reserved.

Studies on the organometallic palladium coordinated carbosillane liquid crystalline dendrimer

A novel complex - palladium-coordinated ate-type liquid crystalline dendrimer was synthesized by a divergent approach, The product showed liquid crystalline properties from 115 degrees C to 187 degrees C, and it belonged to dinuclear species, containing two palladium centers linked by two bridging Cl, each palladium atom completes its coordinations with N atom and a sigma bond to an ortho-carbon in the phenyl ring. The microanalytical values obtained for the product are in agreement with those of compound containing ligand, palladium:and chlorine in a molar ratio of 1 : 1 : 1 and 12 palladium atoms for every scaffold.

Plasma modification of aromatic polyamide reverse osmosis composite membrane surface

The surface of aromatic polyamide reverse osmosis composite membrane was modified by oxygen and argon plasma. The water permeability of oxygen-plasma-modified membrane increases, and the chlorine resistance of argon-plasma-modified membrane increases. The spectra of the attenuated total reflection-Fourier transform infrared and X-ray photoelectron spectroscopy and the contact angle of the water were analyzed to explain the improvement of the two performances of the composite membrane. The carboxyl groups were introduced when modified by oxygen plasma, and cross-linking occurred when modified by argon plasma. (C) 1997 John Wiley & Sons, Inc.

Effective interface of a composite membrane serving as an ideally ultrathin barrier layer

A novel idea relating to the selective barrier layer of a composite membrane is described. The effective interface of the composite membrane could act as a barrier layer which could be controlled to an ideally ultrathin thickness. A new type of polyamide composite membrane was prepared according to this idea, which possessed permeability and chemical resistance more than one magnitude greater than those of ordinary polyamide composite membranes. Copyright (C) 1996 Elsevier Science Ltd.

Chlorination and oxidation of aromatic polyamides .2. Chlorination of some aromatic polyamides

The effects of chlorine on three kinds of aromatic polyamides: those not containing a substituent, those containing substituents, and those containing heterocyclic aromatic rings, were studied. The correlations between the chemical structures of polyamides and the reactivity to hypochlorous acid were examined by IR and C-13 solid-state NMR spectra before and after chlorination. It was found that the chlorination of polyamides depends not only on their chemical structures but also on chlorination conditions such as pH value and reaction time. Their response to chlorination corresponds to four types: ring-chlorination, no reaction, N-chlorination, and chain cleavage. (C) 1996 John Wiley & Sons, Inc.