Numerical simulation of evolution-induced catastrophe

A numerical simulation of damage evolution in a two-dimensional system of micocracks is presented. It reveals that the failure is induced by a cascade of coalescences of microcracks, and the fracture surface appears fractal. A model of evolution-induced catastrophe is introduced. The fractal dimension is found to be a function of evolution rule only. This result could qualitatively explain the correlation of fractal dimension and fracture toughness discovered in experiments.

Ballistic impact of ceramics

The impact behaviour of a range of glass and ceramic materials has been studied using high-speed photography. A gas gun was used to project hardened spheres at plate specimens in the velocity range 30 to 1000m s-1. The target materials included soda-lime glass, boron carbide and various glass ceramics and aluminas. The performance of a particular ceramic was found to depend on a combination of parameters but of key importance was the relative hardness of the projectile and target materials. The fracture toughness, K(IC), had only a secondary effect.

Analysis of Kic and its temperature dependence of metals by a simplified dislocation model

The relative Kic values of metals are calculated with a simplified dislocation model. It is found that the ratio of KIIc to KIc and the temperature dependence of fracture toughness of some metals estimated with this model are consistent with the experimental results.

激光淬火基体对镀铬层断裂韧性的影响

为提高30CrNi2MoVA钢镀铬身管的寿命,采用YAG激光器对钢基体进行激光搭接淬火再镀铬的复合工艺。用多裂纹拉伸技术对经激光搭接处理的30CrNi2MoVA钢再镀铬后的铬层和普通铬层的断裂韧性进行比较。结果表明,激光淬火处理基体可以提高镀铬层的断裂韧性。力学模型分析表明,基体残余压应力以抵抗基体拉伸变形的方式提高了铬层的断裂韧性;化学去基体法研究铬层界面表明,激光处理基体以细化基体影响层的晶粒形式提高了铬层的强度和韧性。离子刻蚀横截面对拉伸结果作了进一步验证。

涂层断裂韧性的声发射辅助拉伸测量方法

涂层的断裂韧性与界面结合强度是表征涂层/基体材料体系力学性能的重要指标.但如何准确地测量涂层的断裂韧性和强界面结合的涂层/基体材料体系的界面结合强度至今仍存在困难.以铬涂层/钢基体材料为对象,采用声发射和显微镜实时动态检测技术与拉伸实验相结合的方法,探索了铬涂层的断裂韧性以及铬涂层/钢基体的界面剪切强度.根据相关力学模型和实验测量结果,得到铬涂层在室温下的断裂韧性为27.41J/m~2. 同时,发现在铬涂层裂纹饱和后界面开裂都未发生,获得了该种材料体系界面剪切强度的一个下限值.

高硅氧发光玻璃的制备及其荧光性能

abstract {Silica glass is an attractive host matrix for the emission ions of rare earth and transition metal ions because it has small thermal expansion coefficient, strong thermal resistance, large fracture strength and good chemical durability and so on. However, a major obstacle to using it as the host matrix is a phenomenon of concentration quenching. In this paper, we introduces a novel method to restrain the concentration quenching by using a porous glass with SiOb>2b> content > 95% (in mass) and prepare intense fluorescence high-SiOb>2b> glasses and high-SiOb>2b> laser glass. The porous glass with high-SiOb>2b> content was impregnated with rare-earth and transition metal ions, and consequently sintered into a compact non-porous glass in reduction or oxidization atmospheres. Various intense fluorescence glasses with high emission yields, a vacuum ultraviolet-excited intensely luminescent glass, high silica glass containing high concentration of Er³⁺ ion, ultrabroad infrared luminescent Bi-doped high silica glass and Nd³⁺-doped silica microchip laser glass were obtained by this method. The porous glass is also favorable for co-impregnating multi-active-ions. It can bring effective energy transferring between various active ions in the glass and increases luminescent intensity and extend range of excitation spectrum. The luminescent active ions-doped high-SiOb>2b> glasses are potential host materials for high power solid-state lasers and new transparent fluorescence materials.}

Effects of process on microstructure and properties of translucent Dy-alpha-SiAlON sintered at lower temperatures

Hot pressing (HP) at higher sintering temperature has been a traditional and prevalent technique for the fabrication of alpha-SiAlON. In order to prepare translucent SiAlON more easily, LiF was used as a non-oxide sintering additive to lower the sintering temperature to <= 1650 degrees C. As a result, all of the samples possessed a good hardness and fracture toughness. At the same time, the lower temperature sintered samples showed a higher optical transmittance in the range of 2.5-5.5 mu m wavelength (0.5 mm in thickness). The maximum infrared transmission reached 68% at a wavelength of 3.3 mu m. The present work shows that the sintering process has a strong effect on microstructure and property of alpha-SiAlON. To be exact, a lower sintering temperature and longer holding time can produce some fully-developed microstrcture, which is beneficial for the optical transmittance. (C) 2008 The Ceramic Society of Japan. All rights reserved.

La2Zr2O7的增韧及陶瓷纤维的制备

La2Zr2O7是一种近年来才提出的新型热障涂层材料，该材料熔点高，在熔点以下不发生相变，热导率低，抗烧结及没有氧传输发生，这些特点使得它作为一种高温下应用的热障涂层材料越来越引起人们的重视。但是，由于该材料的热膨胀系数和断裂韧性比较低，它的实际应用受到了限制。 在本论文中，使用高压烧结的方法获得了致密化的纳米La2Zr2O7块体材料，并对其断裂韧性和热膨胀系数进行了研究。得到的La2Zr2O7纳米材料的断裂韧性和热膨胀系数分别为1.98MPam1/2和9.6×10-6K-1 (200-1000℃)，这些数值明显高于非纳米的La2Zr2O7陶瓷(断裂韧性和热膨胀系数分别为1.40 MPam1/2 和 9.1×10-6 K-1，该结果表明纳米化是一种提高材料断裂韧性和热膨胀系数的有效方法。在La2Zr2O7纳米粉末中加入8YSZ纳米颗粒，高压烧结后使其颗粒充分生长，在得到的复相化合物中观察到形成了类似棒状晶体的自增韧相，使得复合材料的断裂韧性(1.88 MPam1/2)比La2Zr2O7有所提高，甚至超过了同样条件下制备的8YSZ样品的断裂韧性。 La2Zr2O7的断裂韧性也可以通过在基体中添加BaTiO3铁电材料得到明显的提高。当添加BaTiO3的体积含量达到10vol％时，4.5GPa，1450℃高压烧结10min得到的复合材料断裂韧性达1.98 MPam1/2，明显高于同条件下烧结的La2Zr2O7 (1.60MPam1/2)。应力诱导下BaTiO3的电畴转向是主要的增韧原因。随着BaTiO3颗粒添加的体积含量增加，复相化合物的热膨胀系数也明显提高。当掺杂20vol％BaTiO3时，得到的复合材料平均热膨胀系数达到10.2×10-6K-1 (150~1200℃)。 我们通过在4.5GPa, 1650℃高压烧结5min的方法还获得了掺杂YAG纳米颗粒的La2Zr2O7纳米复相陶瓷。在室温下测量了材料的维氏硬度，并通过压痕裂纹长度计算出了材料的断裂韧性。随着YAG纳米颗粒体积含量的增加，纳米复相陶瓷的断裂韧性和维氏硬度都依次增加，当添加20vol％的YAG纳米颗粒时达到最大，分别为1.93 MPam1/2和11.45GPa。断裂韧性增加的机理可归结为以下三点：一是YAG纳米颗粒的添加提高了La2Zr2O7基体的晶界强度，二是基体晶粒尺寸变化的影响，三是YAG纳米颗粒对裂纹的偏转和钉扎作用。添加微米YAG颗粒的复相化合物因为和纳米复相陶瓷具有不同的增韧机制，因此断裂韧性的变化趋势也不相同，在掺入10vol％的YAG微米颗粒时，复合材料的断裂韧性最大，而后降低，当掺入YAG微米粒子的体积含量达到20vol％时，断裂韧性甚至低于La2Zr2O7。 从20世纪90年代开始，电纺作为一种合成纤维的办法越来越吸引人们的注意。其合成的纤维长度长，直径均匀，并且组成范围很广。最初，电纺只是被用来合成一些有机聚合物的纤维，最近，很多研究组开始致力于使用电纺的方法合成复合纤维或者陶瓷纤维。 在本论文中，我们使用电纺的方法获得了La2Zr2O7纳米纤维和SiC单晶纳米线。1000℃煅烧得到的La2Zr2O7纳米纤维具有烧绿石结构，直径在200~500nm之间。同样的温度煅烧时得到的La2Zr2O7纳米纤维的比表面积要明显高于粉末样品的，表明纤维的抗烧结性能比粉末的高。得到的SiC纳米线直径在50~100nm之间，表面有一约5nm厚的无定形的SiO2薄层。 使用电纺的方法，恰当的控制煅烧条件，我们获得了La2Ce2O7， La2(Zr0.745Ce0.386)2O7.524和8YSZ中空纤维。这种中空结构减小了粒子之间的接触面积，提高了材料的抗烧结性能。在扫描电镜分析的基础上，我们总结了这些中空纤维的形成过程。

热喷涂涂层界面断裂韧性的反向三点弯曲法试验

以热喷涂NiCrBSi涂层/钢基体为材料模型,利用将涂层置于受压侧的反向三点弯曲法试验,对热喷涂涂层界面断裂现象进行分析并建立相应的界面断裂韧性计算模型.结果表明,界面裂纹起始于三点弯曲试样中部,对应于加载压头与涂层接触区域正下方的界面上,并向两侧扩展,伴随涂层屈曲,形成分层屈曲的破坏形貌.根据分层屈曲形貌建立计算模型,通过分层屈曲几何参数与屈曲临界应力、涂层内真实应力以及界面断裂韧性的关系,获得界面断裂韧性值.

Lanthanum zirconate ceramic toughened by BaTiO3 secondary phase

La2Zr2O7 (LZ) is a promising thermal barrier coating material for the high-temperature applications, which could be significantly toughened by the BaTiO3 piezoelectric phase incorporated into the matrix. The composites of xBaTiO(3)/(l-x)LZ (x=5, 10, 15, 20 vol%, LZ-x-BaTiO3) were densified by means of high-pressure sintering (HPS) under a pressure of 4.5 GPa at 1450 degrees C for 10 min, by which a high relative density above 93% could be obtained.

Influence of Annealing on Microstructure and Mechanical Properties of Isotactic Polypropylene with beta-Phase Nucleating Agent

The microstructure and mechanical properties of beta-nucleated iPP before and after being annealed at different temperatures (90-160 degrees C) have been analyzed, Annealing induced different degrees of variation in fracture toughness of beta-nucleated iPP samples. namely, slight enhancement at relatively low annealing temperatures (< 110 degrees C) and great improvement at moderate temperatures (120-130 degrees C), whereas dramatic deterioration at relatively high temperatures ( > 140 degrees C) has been observed. The variation of fracture toughness of beta-nucleated iPP is observed to be dependent on the content of beta-NA. Experiments, including scanning electronic microscope (SEM), wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS), and dynamic mechanical analysis (DMA), are performed to study the variations of microstructures as well as the toughening mechanism of the beta-nucleated iPP after being annealed.

Effect of the addition of YAG(Y3Al5O12) nanopowder on the mechanical properties of lanthanum zirconate

La2Zr2O7 (LZ) is a promising thermal barrier coating material for the high-temperature applications, which could be significantly toughened by the YAG nanopowder incorporated into the matrix. The composites of xYAG/(1-x)LZ (Y=10, 15, 20 vol. %, LZ-x-YAG) were densified by means of high-pressure sintering (HPS) under a pressure of 4.5 GPa at 1650 degrees C for 5 min, by which a high-relative density above 93% could be obtained. The morphologies of the fractured surfaces were investigated by the scanning electron microscope, and the fracture toughness and Vicker's-hardness of the composites were evaluated by the microindentation. The grain size of the LZ matrix drops significantly with the addition of YAG nanoparticles and the fracture type changes from the intergranular to a mixture type of the transgranular and intergranular in the nanocomposites. The LZ-20-YAG nanocomposite has a fracture toughness of 1.93 MPa m(1/2), which is obviously higher than that of the pure LZ (1.57 MPa m(1/2)), and the toughening mechanism is discussed in this paper.

Application of rare earths in thermal barrier coating materials

Rare earths are a series of minerals with special properties that make them essential for applications including miniaturized electronics, computer hard disks, display panels, missile guidance, pollution controlling catalysts, H-2-storage and other advanced materials. The use of thermal barrier coatings (TBCs) has the potential to extend the working temperature and the life of a gas turbine by providing a layer of thermal insulation between the metallic substrate and the hot gas. Yttria (Y2O3), as one of the most important rare earth oxides, has already been used in the typical TBC material YSZ (yttria stabilized zirconia). In the development of the TBC materials, especially in the latest ten years, rare earths have been found to be more and more important. All the new candidates of TBC materials contain a large quantity of rare earths, such as R2Zr2O7 (R=La, Ce, Nd, Gd), CeO2-YSZ, RMeAl11O19 (R=La, Nd; Me=Mg, Ca, Sr) and LaPO4. The concept of double-ceramic-layer coatings based on the rare earth materials and YSZ is effective for the improvement of the thermal shock life of TBCs at high temperature.

Study of hydrogen-bonded blend of polylactide with biodegradable hyperbranched poly(ester amide)

Polylactide (PLA) was melt blended with a biodegradable hyperbranched poly(ester amide) (HBP) to enhance its flexibility and toughness without sacrificing comprehensive performance. The advantage of using HBP was due to its unique spherical shape, low melt viscosity, and abundant functional end groups together with its easy access. Rheological measurement showed that blending PLA with as little as 2.5% HBP resulted in a 40% reduction of melt viscosity. The glass transition temperature (T-g) of PLA in the blends decreased slightly with the increase of HBP content, indicating partial miscibility which resulted from intermolecular interactions via H-bonding. The H-bonding involving CO of PLA with OH and NH of HBP was evidenced by FTIR analysis for the first time. The HBP component, as a heterogeneous nucleating agent, accelerated the crystallization rate of PLA. Remarkably, with the increase of HBP content, the elongation at break of PLA blends dramatically increased without severe loss in tensile strength, even the tensile strength increased within 10% content of HBP. The stress-strain curves and the SEM photos of impact-fractured surface showed the material changed from brittle to ductile failure with the addition of HBP. Reasonable interfacial adhesion via H-bonding and finely dispersed particulate structure of HBP in PLA were proposed to be responsible for the improved mechanical properties.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .4. Cure cycle simulation

Epoxy-terminated poly(phenylene ether ketone) (E-PEK) developed in this Institute is a candidate matrix resin for polymer composites as structural materials. Cure cycles for this reaction system were simulated according to the previously established processing model. It is found that for the E-PEK system, the curing process is best completed by a stepwise cure cycle comprising two isothermal processes at different temperatures, T-1 and T-2. The cure cycles over a wide range of processing parameters simulated, based on the established processing model, indicate that the processing window is width-adjustable. Analysis of the mechanical properties of the composite sheets showed that the simulated cure cycles are acceptable and reliable. (C) 1997 John Wiley & Sons, Inc.