Microstructures and mechanical properties of the Mg-4.5Zn-xGd (x = 0, 2, 3 and 5) alloys

Microstructures and mechanical properties of the peak-aged Mg-4.5Zn-xGd (x = 0, 2, 3 and 5 wt.%) alloys have been investigated. The results showed that grain size increased with increasing Gd. Phase analysis showed that MgZn2 phase was observed in the Mg-4.5Zn alloy. While with Gd additions, Mg3Gd and Mg3Gd2Zn3 phases formed, and the volume fraction of the Mg3Gd2Zn3 phase increased with increasing Gd. Tensile test results indicated that the optimal mechanical properties were obtained in the Mg-4.5Zn-2Gd alloy, and the ultimate tensile strength and yield strength were 215 MPa and 121 MPa, respectively.

Ring-Enlargement of Dimethylaminopropenoyl Cyclopropanes: An Efficient Route to Substituted 2,3-Dihydrofurans

A convenient and efficient synthesis of substituted dihydrofurans is developed via ring-enlargement of 1-dimethylaminopropenoyl-1-carbamoyl/benzoyl cycloproparres catalyzed by ammonium acetate in acetic acid with high regio- and stereoselectivity. Some of the newly synthesized substituted dihydrofurans are subjected to further synthetic transformation in the presence of NaOH (aq) in ethanol to afford the corresponding 5-aryl-2,3-dihydrofuro[3,2-c]pyfidin-4(5H)-ones in high yields.

1,2,3,4-Alternate double cone conformational extreme in the supramolecular assemblies of p-sulfonatocalix[8]arene

Two supramolecular assemblies of p-sulfonato-calix[8]arene were stacked by some infinite 1D 'molecular capsule' chains in which the calixarenes adopt an unprecedented 1,2,3,4-alternate double cone conformation.

Metal-organic frameworks based on the pyridine-2,3-dicarboxylate and a flexible bispyridyl ligand: syntheses, structures, and photoluminescence

Three new metal-organic coordination polymers, [Cu(2,3-pydc)(bpp)]center dot 2.5H(2)O (1), [Zn(2,3-pydc)(bpp)]center dot 2.5H(2)O (2) and [Cd(2,3-pydc)(bpp)(H2O)]center dot 3H(2)O (3) (2,3-pydcH(2) = pyridine-2,3-dicarboxylic acid, bpp 1,3-bis(4-pyridyl)propane), have been synthesized at room temvperature. All complexes have metal ions serving as 4-connected nodes but represent two quite different structural motifs. Complexes 1 and 2 are isomorphous, both of which feature 2D -> 3D parallel interpenetration. Each two-dimensional (2D) layer with (4, 4) topology is interlocked by two nearest neighbours, one above and one below, thus leading to an unusual 3D motif. Complex 3 has a non-interpenetrating 3D CdSO4 framework with cavities occupied by uncoordinated water molecules.

Syntheses and Crystal Structures of Fused Thiophenes: [7]Helicene and Double Helicene, a D-2-Symmetric Dimer of 3,3 '-Bis(dithieno[2,3-b:3 ',2 '-d]thiophene)

The efficient synthesis of (TMS)(2)-[7]helicene (rac-3) and double helicene, a D-2-symmetric dimer of 3,3'-bis(dithieno-[2,3-b:3',2'-d]thiophene) (rac-4) was developed. The crystal structures of 3 and 4 show both strong intermolecular pi-pi interactions and S center dot center dot center dot S interactions. UV/vis spectra reveal that both 3 and 4 show significant pi-electron delocalization.

A novel sensitive solid-state electrochemiluminescence sensor material: Ru(bpy)(2+)(3) doped SiO2@MWNTs coaxial nanocable

A simple, large scale, and one-step process for the preparation of tris(2,2'-bipyridyl)ruthenium(I) (Ru(bpy)(3)(2+)) doped SiO2@carbon nanotubes (MVNTs) coaxial nanocable used for an ultrasensitive electrochemiluminescence (ECL) is presented for the first time. More importantly, a directly coated as-formed functional material on ITO electrode surface exhibits excellent ECL behavior, good stability, and high sensitivity in the presence of tripropylamine (TPA). This novel functional material will find potential applications in biosensor, electrophoresis and electroanalysis.

Efficient synthesis of substituted tetrahydrothiopyrano[2,3-b]thiopyran-4,5-diones by a double annulation strategy from dialkenoylketene dithioacetals

An efficient synthetic procedure for substituted 2,3,6,7tetrahydrothiopyrano [2,3-b] thiopyran-4,5 -diones by a double annulation strategy is described. The ring systems are made in good yields from readily available dialkenoylketene dithioacetals in the presence of either sodium sulfide nonahydrate/N,N-dimethylformamide (DMF) or a sodium hydride/DMF/amine system.

Efficient synthesis of trimethylsilyl-substituted dithieno[2,3-b:3',2'-d]thiophene,tetra[2,3-thienylene] and hexa[2,3-thienylene] from substituted [3,3']Bithiophenyl

Efficient synthetic procedures for the preparation of beta-trithiophenes (dithieno[2,3-b:3',2'-d]thiophene) and two macrocyclic compounds, tetra[2,3-thienylene] and hexa[2,3-thienylene] bearing trimethylsilyl (TMS) groups from 2,2'-dibromo-5,5'-bistrimethylsilanyl[3,3']bithiophenyl are reported. The UV-Vis spectra property and crystal structures of these macrocyclic oligothiophenes are described.

Synthesis and properties of novel polyimides derived from 2,2 ',3,3 '-benzophenonetetracarboxylic dianhydride

A new synthetic route to 2,2',3,3'-BTDA (where BTDA is benzophenonetetracarboxylic dianhydride), an isomer of 2,3',3',4'-BTDA and 3,3',4,4'-BTDA, is described. Single-crystal X-ray diffraction analysis of 2,2',3,3'-BTDA has shown that this dianhydride has a bent and noncoplanar structure. The polymerizations of 2,2',3,3'-BTDA with 4,4'-oxydianiline (ODA) and 4,4'-bis(4-aminophenoxy)benzene (TPEQ) have been investigated with a conventional two-step process. A trend of cyclic oligomers forming in the reaction of 2,2',3,3'-BTDA and ODA has been found and characterized with IR, NMR, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, and elemental analyses. Films based on 2,2',3,3'-BTDA/TPEQ can only be obtained from corresponding polyimide (PI) solutions prepared by chemical imidization because those from their polyamic acids by thermal imidization are brittle. PIS from 2,2',3,3'-BTDA have lower inherent viscosities and worse thermal and mechanical properties than the corresponding 2,3',3',4'-BTDA- and 3,3',4,4'-BTDA-based PIs. PIs from 2,2',3,3'-BTDA and 2,3',3',4'-BTDA are amorphous, whereas those from 3,3',4,4'-BTDA have some crystallinity, according to wide-angle X-ray diffraction.

Synthesis and properties of polyimides derived from cis- and trans-1,2,3,4-cyclohexanetetracarboxylic dianhydrides

Cis-1,2,3,4-cyclohexanetetracarboxylic dianhydride (cis-1,2,3,4-CHDA) was synthesized. It was found that under such conditions as heating or boiling in acetic anhydride, cis-1,2,3,4-CHDA could be converted to its trans-isomer. The process of thermal isomerization was monitored by H-1 NMR spectra and the mechanism of conversion was proposed. Their absolute structures of cis- and trans-1,2,3,4-CHDAs were elucidated by single crystal X-ray diffraction. The polycondensations of cis- and trans-1,2,3,4-CHDAs with aromatic diamines such as 4,4'-oxydianiline (ODA), 4,4'-methylenedianiline (MDA), 4,4'-diamino-3,3'-dimethyldiphenylmethane (DMMDA), 4,4'-bis(4-aminophenoxy)benzene (TPEQ), 2,2-bis[4-(4-aminophenoxy)phenyl] propane (BAPP) were studied. It is easy to obtain higher molecular weight polyimides from trans-1,2,3,4-CHDA using conventional one-step or two-step methods. However, higher molecular weight polyimides derived from cis-1,2,3,4-CHDA could not be prepared by the usual methods (solid content ca. 10%) owing to the trend of forming cyclic oligomers.

2,5-二(2-菲基)-[3,2-b]并二噻吩的合成、表征及在有机薄膜晶体管中的应用

近年来,有机薄膜晶体管(OTFTs)因其成本低、加工简便,特别适用于制备大面积柔性器件而引起人们的广泛关注[1].并苯类化合物和噻吩衍生物是目前最重要的两类高迁移率OTFT材料.由并五苯制备的多晶OTFTs器件迁移率可达到5cm2/(V·s)[2];烷基修饰齐聚噻吩的场致迁移率也可达到非晶硅[0·1~1cm2/(V·s)]的水平[3].但是,这两类材料具有较窄的能隙和较高的最高被占分子轨道(HOMO)能级,容易与空气中的氧气和水发生作用,所制备的器件在空气中衰减较快,并且并苯类化合物对光也非常敏感,限制了其应用范围[4~6].因此,制备稳定的高迁移率有机半导体材料是有机光电子研究领域的重要课题之一.制备稳定的高迁移率有机半导体材料的途径包括用较稳定的芳香基团对噻吩齐聚物进行封端,以增大能隙和降低HOMO能级[7].菲类化合物是并苯类化合物的异构体,具有较好的光稳定性[8].[3,2-b]并二噻吩是一种平面稠环分子,与2,2′-二噻吩相比,HOMO能级相对降低,因而具有相对好的稳定性[9].本文合成了2,5-二(2-菲基)-[3,2-b]并二噻吩(PhTT),表征了其基本的物理和化学性质,制备了相应的有机薄膜晶...

6,7,8,9-Tetrahydro-5H-pyrido[2,3-b]azepine-5,8-dione: a hydrogen-bonded dimer structure

In the title compound, C9H8N2O2, two crystallographically independent molecules form a dimer structure, in which two N-H center dot center dot center dot N hydrogen bonds generate an intermolecular R-2(2)( 8) ring.

3{1-[2-(-3-羟基-1-甲基-2-亚丁烯氨基)-苯亚氨基]-乙基}4-甲硫基-2,4-戊二烯-2-醇的不对称Schiff碱镍(Ⅱ)配合物的合成、结构和性质

由 5-(2-乙酰基-1-甲硫基-3-羰基-亚丁基)-丙二酸亚异丙酯 (1)与邻苯二胺及乙酸镍()经一步反应合成了3{1-[2-( -3-羟基-1-甲基-2-亚丁烯氨基)-苯亚氨基 ]-乙基} 4-甲硫基-2,4-戊二烯-2-醇(3)的不对称四齿 Schiff碱镍()配合物(2),X射线衍射结果表明,配合物 2属单斜晶系,P21/C空间群.a=1.1476(2)nm,b=1.1782(2)nm,c=1.4810(3)nm;β=111.73(2)°,V=1.8602(7)nm3,Z=4,Rf=0.0535.电化学(循环伏安)测定结果表明,该配合物在测定条件下(阳极峰电位为1.1)发生了不可逆的氧化-还原反应.

Novel polyimides derived from 2,3,3 ',4 '-benzophenonetetracarboxylic dianhydride

A series of polyimides (PIs) based on 2,3,3',4'-benzophenonetetracarboxylic dianhydride (2,3,3',4'-BTDA) and 3,3',4,4'-BTDA were prepared by the conventional two-step process. The properties of the 2,3,3',4'-BTDA based polyimides were compared with those of polyimides prepared from 3,3',4,4'-BTDA. It was found that PIs from 2,3,3,4'-BTDA have higher glass transition temperature and better solubility without sacrificing their thermal properties. Furthermore the theological properties of PMR-15 type polyimide resins based on 2,3,3',4'-BTDA showed lower melt viscosity and wider melt flow region (flow window) compared with those from 3,3',4,4'-BTDA. The structure-property relations resulted from isomerism were discussed.

Preparation and gas sensitivity of octa-n-butoxy-2,3-naphthalocyanine copper(II) Langmuir-Blodgett film

The formation process of monolayer of octa-n-butoxy-2,3-naphthalocyanine copper ( I), [CuNc(OBu)(8)], on water subphase was studied. Its multilayers were successifully deposited on the hydrophilic substrates by Z-type deposition mode using LB technique. Stable solid film with a limiting molecular area of 0.74 nm(2) and a collapse pressure of 55 mN/m were formed. The LB film structure was characterized by IR and electronic absorption spectra. Macrocycle of CuNc (OBu)(8) molecules have a face-to-face arrangement in the multilayers. These films have good sensitivities to vapor of alcohols, with the following sequence of sensitivities: i-PrOH>EtOH>MeOH. The response time and recovery time of the LB films to vapor of MeOH, EtOH and i-PrOH[volume fraction (1-5) X 10(-5)] were within 2 and 5 seconds respectively, while those of the LB films to ammonia(1 X 10(-4)) were 30-60 seconds and 4-5 minutes respectively.