长期施肥对黑土中Cu、Cd含量及其剖面分布的影响

以经过8个不同施肥处理的黑土样品为材料,研究长期不同施肥处理下,黑土中Cu、Cd含量的差异。采用原子吸收分光光度法和Tessier-连续提取法,研究黑土中全Cu、全Cd和有效Cu、有效Cd的含量差异。结果表明,有机肥的长期施用,会使土壤中Cu、Cd与有机质发生络合并使Cu、Cd在土壤表层累积;秸秆和氮磷钾(S+NPK)化肥的长期配合施用,有利于作物对有效Cu和Cd的吸收,从而使Cu、Cd在土壤中没有明显积累;NP及NPK处理下,二铵、氯化钾肥对土壤中Cu、Cd积累的影响不明显。长期耕作不施肥(CK)处理时,因无外源Cu、Cd,以及作物对有效Cu、Cd的长期吸收,土壤中Cu、Cd含量低于不耕作不施肥(休闲)处理的。从垂直剖面上看,Cu、Cd主要积累在黑土表层,而表层以下不同施肥处理间Cu、Cd含量的差异和变幅不大。有机肥料能明显地向土壤中带入Cu、Cd,造成Cu、Cd在土壤表层的积累,并由于植物体的吸收对人体造成潜在危害,而其他化学肥料对土壤中Cu和Cd积累的影响不明显。本研究为人们的生产实践提供了施肥理论和依据,并且对土壤的污染防治也具有现实意义。

Electrocatalytic properties of Cu-Zr amorphous alloy towards the electrochemical hydrogenation of nitrobenzene

The Cu-Zr amorphous alloy was studied as an electrocatalyst towards the electrochemical hydrogenation of nitrobenzene. The electrocatalyst was activated by chemical etching in HF solution. Resulted changes in the morphology, chemical composition and crystalline structure of the electrocatalyst surface were characterised by scanning electron microscopy, X-ray diffraction and Auger electron spectroscopy. The electrocatalytic properties of the Cu-Zr amorphous alloy were assessed by voltammetric measurements. Due to the formation and aggregation of Zr residue modified Cu nanocrystals on the surface caused by the selective dissolution of Zr components in the chemical etching, the activated amorphous alloy is an effective electrocatalyst for the electrochemical reduction reaction of nitrobenzene with aniline as the main product. The positive shift of the peak potential and accompanying increase in the value of peak current in voltammograms with increasing Cu content and decreasing Zr content of the alloy surface in the chemical etching are indicative of improved electrocatalytic activity. (C) 2002 Elsevier Science B.V. All rights reserved.

Cyclopropanation on a highly active heterogeneous catalyst: CuO/TiO2-Al2O3

Some heterogeneous catalysts, cupric oxide supported on different supports, were prepared and employed to catalyze the cyclopropanation of styrene and 2,5-dimethyl-2,4-hexadiene with ethyl diazoacetate (EDA). The catalytic performance for cyclopropanation strongly depends on the nature of the support. A novel catalyst, CUO/TiO2-Al2O3, in which Al2O3 is modified with a monolayer TiO2, is found to be most active and selective for the cyclopropanation reaction. The yields of 93 and 94% cyclopropanes are obtained for styrene and 2,5-dimethyl-2,4-hexadiene at 40 degreesC as the substrates, respectively. The activity and selectivity in cyclopropanes are optimized with a monolayer dispersion of cupric oxide on the corresponding supports. (C) 2002 Elsevier Science B.V. All rights reserved.

In situ FT-IR spectroscopic studies of CO adsorption on fresh Mo2C/Al2O3 catalyst

The surface sites of supported molybdenum carbide catalyst derived from different synthesis stages have been studied by in situ FT-IR spectroscopy using CO as the probe molecule. Adsorbed CO on the reduced passivated Mo2C/Al2O3 catalyst gives a main band at 2180 cm(-1), which can be assigned to linearly adsorbed CO on Mo4+ sites. The IR results show that the surface of reduced passivated sample is dominated by molybdenum oxycarbide. However, a characteristic IR band at 2054 cm-1 was observed for the adsorbed CO on MoO3/Al2O3 carburized with CH4/H-2 mixture at 1033 K (fresh Mo2C/Al2O3), which can be assigned to linearly adsorbed CO on Modelta+ (0 < delta < 2) sites Of Mo2C/Al2O3, Unlike adsorbed CO on reduced passivated Mo2C/Al2O3 catalyst, the IR spectra of adsorbed CO on fresh Mo2C/Al2O3 shows similarity to that on some of the group VIII metals (such as Pt and Pd), suggesting that fresh carbide resembles noble metals. To study the stability Of Mo2C catalyst during H-2 treatment and find proper conditions to remove the deposited carbon species, H-2 treatment of fresh Mo2C/Al2O3 catalyst at different temperatures was conducted. Partial amounts of carbon atoms in Mo2C along with some surface-deposited carbon species can be removed by the H, treatment even at 450 K. Both the surface-deposited carbon species and carbon atoms in carbide can be extensively removed at temperatures above 873 K.