扩散处理热浸镀铝钢高温抗氧化行为的研究

对经不同扩散工艺处理的热浸镀铝层高温抗氧化性进行了研究,通过SEM、TEM、XRD分析了经扩散处理后,热浸镀铝层高温氧化过程中组织结构的变化情况,分析了热浸镀铝层高温抗氧化性能和微观结构的关系,确定了提高热浸镀铝层高温抗氧化性的适宜扩散温度。结果表明,经750℃扩散处理,热浸镀铝层结构由较厚的外表层(Fe2Al5+FeAl2)及内层(FeAl+条状:FeAl2)组成,条状FeAl2的形成为氧提供了扩散通道,其抗氧化性较差;经950℃扩散处理,镀层外表层变薄,外表层转为单一FeAl2、内层为FeAl,并出现早期内氧化裂纹,其抗氧化性较差:当扩散处理温度为850℃时,镀层外表层变薄,结构转为FeAl2+少量Fe2Al5,而内层增厚,其结构为FeAl+球状FeAl2,而内层FeAl2球化,增强了氧由内层向基体扩散的阻碍作用,使氧只能逐层形成Al2O3+Fe2O3的氧化膜,提高了镀层的高温抗氧化性。

热浸铝钢等离子体电解氧化陶瓷层的微观力学特性

采用纳米压入方法表征了热浸镀铝钢表面由Al2O3层、Al层和FeAl层组成的复合涂层的纳米硬度、弹性模量及断裂韧性等微观力学性能，采用扫描电镜（SEM）观察了纳米压痕形貌，并分析了孔洞对陶瓷层的纳米压入行为和压痕裂纹扩展的影响．结果表明：等离子体电解氧化（PEO）陶瓷层中包含许多微米和亚微米尺度的细小孔洞，陶瓷层弹性模量约为226．4 GPa，纳米硬度约为19．6 GPa．当纳米压入深度为250nm时，所测得陶瓷层的力学参数分散性较大．与FeAl层比较，PEO陶瓷层具有较高的裂纹扩展阻力．FeAl层纳米压痕顶端产生了沿直线扩展的径向裂纹；而陶瓷层纳米压痕中除径向裂纹外出现了侧边裂纹．

Formation and Structure of Composite Coating of HAD and Micro-Plasma Oxidation on A3 Steel

Composite coatings were obtained on A3 steel by hot dipping aluminum(HAD) at 720 degreesC for 6 min and micro-plasma oxidation (MPO) in alkali electrolyte. The surface morphology, element distribution and interface structure of composite coatings were studied by means of XRD, SEM and EDS. The results show that the composite coatings obtained through HAD/MPO on A3 steel consist of four layers. From the surface to the substrate, the layer is loose Al2O3 ceramic, compact Al2O3 ceramic, At and FeAl intermetallic compound layer in turn. The adhesions among all the layers are strengthened because the ceramic layer formed at the At surface originally, FeAl intermetallic compound layer and substrate are combined in metallurgical form through mutual diffusion during HAD process. Initial experiment results disclose that the anti-corrosion performance and wear resistance of composite coating are obviously improved through HAD/MPO treatment.

BONDING OF ALUMINA AND METAL USING BULK METALLIC GLASS FORMING ALLOY

Metal-alumina joints have found various practical applications in electronic devices and high technology industry. However, making of sound metal ceramic brazed couple is still a challenge in terms of its direct application in the industry. In this work we successfully braze copper with Al2O3 ceramic using Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass forming alloy as filler alloy. The shear strength of the joints can reach 140 MPa, and the microstructrural analysis confirms a reliable chemical boning of the interface. The results show that the bulk metallic glass forming alloys with high concentration of active elements are prospective for using as filler alloy in metal-ceramic bonding.

Investigations of cohesive zone properties of the interface between metal film and ceramic substrate at nano- and micro-scales

Cohesive zone characterizations of the interface between metal film and ceramic substrate at micro- and nano-scales are performed in the present research. At the nano-scale, a special potential for special material interface (Ag/MgO) is adopted to investigate the interface separation mechanism by using MD simulation, and stress-separation relationship will be obtained. At the micro-scale, peeling experiment is performed for the Al film/Al2O3 substrate system with an adhesive layer at the interface. Adhesive is a mixture of epoxy and polyimide with mass ratio 1:1, by which a brittle cohesive property is obtained. The relationships between energy release rate, the film thickness and the adhesive layer thickness are measured during the steady-state peeling. The experimental result has a similar trend as modeling result for a weak adhesion interface case.

薄膜/基体界面的撕裂实验研究

新型材料大都离不开薄膜。薄膜材料广泛应用在表面工程、界面工程、生物材料以及微纳米机电系统(MEMS)等领域。研究和评估薄膜/基体界面的力学性能-特别是在微尺度下,具有重要的科学研究价值和应用价值。划痕和撕裂是微/纳米尺度薄膜力学性能测量的两种主要方法,而撕裂实验相对简单可行,理论分析模型也相对方便建立。本文系统研究了Al/epoxy/Al2O3体系和Cu/Al2O3体系的撕裂实验,开发出一套微尺度薄膜撕裂的实验设备和方法,得出薄膜厚度、撕裂角度、epoxy层厚度等因素对撕裂力的影响。应用微梁弯曲模型和粘聚力(EPZ)模型,本文从总撕裂力中分离薄膜塑性变形耗散能量,得出了所考察薄膜/基体界面的粘结韧性等力学性能。

Al_2O_3/SiC_p复合材料中热失配残余应力的测量

采用纳米压痕仪测量了Al2O3/SiCp复合材料中的热失配残余应力。根据研究材料的微结构和非均匀热残余应力分布特点,建立一压痕实验模型。在该模型中,实验材料被视为由若干含有单一SiC颗粒的Al2O3胞元构成,而热失配残余压应力均匀分布于胞元基体中。在考虑到浅压痕时材料表面粗糙和压头针尖曲率半径的影响的基础上测得的Al2O3/SiCp复合材料基体中热失配残余压应力与理论计算结果非常接近。

Bonding Of Alumina And Metal Using Bulk Metallic Glass Forming Alloy

Metal-alumina joints have found various practical applications in electronic devices and high technology industry. However, making of sound metal ceramic brazed couple is still a challenge in terms of its direct application in the industry. In this work we successfully braze copper with Al2O3 ceramic using Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass forming alloy as filler alloy. The shear strength of the joints can reach 140 MPa, and the microstructrural analysis confirms a reliable chemical boning of the interface. The results show that the bulk metallic glass forming alloys with high concentration of active elements are prospective for using as filler alloy in metal-ceramic bonding.

Infrared luminescence properties of bismuth-doped barium silicate glasses

Infrared (IR) luminescence covering 1.1 to similar to 1.6 mu m wavelength region was observed from bismuth-doped barium silicate glasses, excited by a laser diode at 808 nm wavelength region, at room temperature. The peak of the IR luminescence appears at 1325 nm. A full width half-maximum (FWHM) and the lifetime of the fluorescence is more than 200 nm and 400 mu s, respectively. The fluorescence intensity increases with Al2O3 content, but decreases with BaO content. We suggest that the IR luminescence should be ascribed to the low valence state of bismuth Bi2+ or Bi+, and Al3+ ions play an indirect dispersing role for the infrared luminescent centers.

Strong visible up-conversion emissions and thermometric applications of Er3+-Yb3+ codoped Al2O3 prepared by the sol-gel method

The Er3+-Yb3+ codoped Al2O3 has been prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)(3)]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)(3) center dot 5H(2)O] and ytterbium nitrate [Yb(NO3)(3) center dot 5H(2)O]. The phase structure, including only two crystalline types of doped Al2O3 phases, theta and gamma, was obtained for the 1 mol% Er3+ and 5 mol% Yb3+ codoped Al2O3 at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300-825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er3+-Yb3+ codoped Al2O3 plays an important role in the application of high temperature sensor.

大能量窄线宽全固态钛宝石激光器的研究进展

主要介绍了用于差分吸收激光雷达系统和蓝绿激光通信的大能量、窄线宽全固态脉冲钛宝石（Tn：Al2O3）激光器的应用及其在国内外的研究历史和现状。阐述了目前获得大能量、窄线宽全固态钛宝石激光器的几种典型方法，比较了其优缺点，并对这种激光器的发展前景进行了展望。

970nm抽运下Tm^3／Yb^3＋共掺氧氟玻璃的频率上转换发光

稀土离子掺杂的氧氟玻璃是一种新型上转换发光材料。制备了Tm^3／Yb^3＋单掺、共掺的摩尔分数为n（SiO2）-0．30，n（PbF2）-0．50，n=（Al2O3）=0．15，n（AlF3）=（0．049-x），n（TmF3）=y，n（YbF3）=x（x=0，0．001，0．010，0．015，0．020，y=0，0．001）系统氧氟玻璃，研究了其上转换发光特性、分析了其上转换发光机理。研究发现，在970nm抽运光源激发下，Tm^3＋单掺时没有可见光上转换发射；而加入Yb^3＋后产生了强的蓝光（452n

Broadband near-infrared emission from transparent Ni2+-doped silicate glass ceramics

Transparent Ni2+-doped MgO-Al2O3-TiO2-SiO2 glass ceramics were prepared, and the optical properties of Ni2+-doped glass ceramics were investigated. Broadband emission centered at 1320 nm was observed by 980 nm excitation. The longer wavelength luminescence compared with Ni2+-doped Li2O-Ga2O3-SiO2 glass ceramics is ascribed to the low crystal field hold by Ni2+ in MgO-Al2O3-TiO2-SiO2 glass ceramics. The change in optical signals at the telecommunication bands with or without 980 nm excitation was also measured when the seed beam passes through the bulk gain host.(C) 2007 American Institute of Physics.

不同氧磷比对磷酸盐包边玻璃性质的影响规律

包边技术是提高大尺寸激光玻璃饱和增益系数的关键技术。采用传统的方法熔制玻璃,研究了 P2O5含量对 P2O5-Al2O3-B2O3-CuCl-Na2O-ZnO磷酸盐包边玻璃的折射率、热膨胀系数、玻璃转变温度、膨胀软化温度以及化学稳定性的影响。结果表明：当 P2O5的摩尔分数为 60%左右,玻璃样品具有最高的折射率（1.522 0）、最低的玻璃转变温度（352.4 ℃）、较好的化学稳定性[0.52 mg/（cm^2·d）]和适宜的热膨胀系数（128.427×10^-7/℃）,是用作钕磷酸盐激光玻璃硬包边的理

微晶玻璃在大功率脉冲氙灯封接中的应用

：为提高大功率脉冲氙灯的封接强度，将微晶玻璃作为封接材料引入到氙灯封接应用中. 以 Bi2O3,ZnO,Al2O3,MgO,CaCO3,SiO2,BaO,H3BO3,P2O5,Na2O 为原料，通过高温熔融制备了大功率脉冲氙灯封接 用微晶玻璃样品. 测试了样品的热膨胀系数,并通过差热分析(Differential Thermal Analysis，DTA)对脉冲氙灯 微晶玻璃的封接温度进行了讨论，用X 射线衍射(X-ray diffraction ，XRD)表征了封接玻璃，并进行了分析. 将 制得的样品磨成玻璃粉末，制成膏剂状玻璃焊料，对大功率脉冲氙灯进行封接，得到大功率脉冲氙灯的微晶 玻璃封接件. 通过氦质谱检漏仪检测，1#、2#、4#封接件气密性良好，达到10-6 Pa.