Mineralogy of smectites in the surface sediments from the East Pacific and its significance

XRD, TEM, SEM and EDS are employed to analyze smectites in the clay fraction of the surface sediments from the East Pacific. It is shown from the XRD results that the clay fraction consists of about 20% smectites. Three types of smectites are identified, Fe-rich (Type I), Fe, Mg-rich (Type II) and Na,Ca smectite (Type III), and most of them are not well-crystallized. Type I is widely distributed in sediments, showing honeycomblike in the SEM, and aggregated or dispersive hairlike, or cloudy assemblage with a bit curl near its edge in the TEM. This type is considered to be typomorphic type of authigenic smectite in the East Pacific. Type II is similar to Type I in micromorphology in the TEM, showing a transition micronite, while Type III is tabletlike in the TEM with an unclear edge. Type I may be altered from volcanics and some of them even precipitated from the low subthermal water. Type II could also be formed in the ocean floor, while Type III comes from dry and distant continental area. This study suggests that the characteristic of chemical composition and morphology of smectite may give a clue to understand sediment source, origin of minerals and sedimentation in the deep sea.

Impacts of anthropogenic activity on the recent evolution of the Huanghe (Yellow) River delta

Hydrological statistical data, remote sensing images, and bathymetric charts were used to study the recent evolution of the Huanghe (Yellow) River delta under human-induced interventions. It was clear that water and sediment discharge from the Huanghe River had dropped rapidly since 1970, particularly after 1986. The water and sediment discharges for the period of 1986-2000 were found to have been reduced to only 29.2% and 31.2% of those in the period of 1950-69. This was caused by human factors in the upper and middle reaches of the Huanghe River, including water diversion, damming and reservoir construction, and water and soil conservation. Based on the results from visual interpretation of processed Landsat (MSS or TMJETM+) images dated from 1976 to 2001 and two digital elevation models generated from bathymetric charts surveyed in 1976 and 1992, we found that human-induced reduction of water and sediment discharge led to coastline retrogradation, with the maximum mean recession rate of -0.51 km yr-1 over the period of 1976-98, and seabed erosion beyond the -20 m isobath between 1976 and 1992. Other impacts of human activities on the recent evolution of the Huanghe River delta, including tidal flats shrinking, artificial coastline increasing, land surface sinking and so on, were also analyzed. We found that: (i) the whole delta, including subaerial and subaqueous, has turned from a highly constructive period to a destructive phase; (ii) channelization and dredging were two of the main causes of delta destruction; (iii) land loss in the Huanghe River delta caused by submersion will be increased in the near future; (iv) the Huanghe River delta was becoming more fragile and susceptible to natural hazards.

Dynamics of the buoyant plume off the Pearl River Estuary in summer

Field measurements of salinity, wind and river discharge and numerical simulations of hydrodynamics from 1978 to 1984 are used to investigate the dynamics of the buoyant plume off the Pearl River Estuary (PRE), China during summer. The studies have shown that there are four major horizontal buoyant plume types in summer: Offshore Bulge Spreading (Type I), West Alongshore Spreading (Type II), East Offshore Spreading (Type III), and Symmetrical Alongshore Spreading (Type IV). River mouth conditions, winds and ambient coastal currents have inter-influences to the transport processes of the buoyant plume. It is found that all of the four types are surface-advected plumes by analysing the vertical characteristic of the plumes, and the monthly variations of the river discharge affect the plume size dominantly. The correlation coefficient between the PRE plume size and the river discharge reaches 0.85 during the high river discharge season. A wind strength index has been introduced to examine the wind effect. It is confirmed that winds play a significant role in forming the plume morphology. The alongshore wind stress and the coastal currents determine the alongshore plume spreading. The impact of the ambient currents such as Dongsha Current and South China Sea (SCS) Warm Current on the plume off the shelf has also assessed. The present study has demonstrated that both the river discharge and wind conditions affect the plume evolution.

Evolution of freshwater plumes and salinity fronts in the northern Bay of Bengal

[1] The evolution of freshwater plumes and the associated salinity fronts in the northern Bay of Bengal ( henceforth the bay) is studied using rotated empirical orthogonal function (REOF) analysis and extended associate pattern analysis (EAPA). The results show that sea surface salinity distribution is featured by eastern-bay and western-bay plumes in the northern bay during different seasons. The western-bay plume begins in early July, peaks in late August, and then turns into a bay-shaped plume with the two plumes in either side of the bay, which peaks in late October. The southward extension of the western-bay plume can be explained by the southwestward geostrophic flow associated with the cyclonic gyre in the northern bay, which counters the northeastward Ekman drift driven by wind stress. The offshore expansion of the western-bay plume is induced by the offshore Ekman drift which also produces a salinity front near the east coast of India. The bay-shaped plume appears when the cyclonic gyre shifts westward and a weak anticyclonic gyre occupies the northeastern bay. As the season advances, the western part of the bay-shaped plume decays while the eastern part persists until the following June, which is believed to be associated with the anticyclonic gyre in the northern bay. The evolution of the plumes except the eastern part of the bay-shaped plume in fall can be partly explained by the seasonal variation of mass transport associated with the Sverdrup balance. The fact that the western-bay (eastern-bay) plume appears when surface freshwater flux in the northeastern bay increases ( decreases) dramatically suggests that the plumes are not produced directly by surface freshwater flux. River discharge seems to be the freshwater source for the plumes and has little to do with the evolution of the plumes.

Evolution of nutrient structure and phytoplankton composition in the Jiaozhou Bay ecosystem

The inventories of nutrients in the surface water and large phytoplankton( > 69 pm) were analyzed from the data set of JERS ecological database about a typical coastal waters, the Jiaozhou Bay, China, from 1960s for N, P and from 1980s; for Si. By examining long-term changes of nutrient concentration, calculating stoichiometric balance, and comparing diatom composition, Si limitation of diatom production was found to be more possible. The possibility of Si limitation was from 37% in 1980s to 50% in 1990s. Jiaozhou Bay ecosystem is becoming serious eutrophication, with notable increase of NO2-N, NO3-N and NH4-N from 0.1417 mumol/L, 0.5414 mumol/L, 1.7222 mumol/L in 1960s to 0.9551 mumol/L, 3.001 mumol/L, 8.0359 mumol/L in late 1990s respectively and prominent decrease of Si from 4.2614 mumol/L in 1980s to 1.5861 mumol/L in late 1990s; the nutrient structure is controlled by nitrogen; the main limiting nutrient is probably silicon; because of the Si limitation the phytoplankton community structure has changed drastically.

Pollen morphology and its in systematic and ecological significance in Rheum (Polygonaceae) from China

Pollen morphology of 40 species of Rheum, belonging to eight sections, was investigated under LM and SEM. Four new exine patterns were found in the species: a) microcchinate-foveolate, b) rugulate, c) verrucate-perforate, and d) verrucaterugulate ornamentation. In addition, two patterns, the Rheum-type pollens with microechinate-perforate and fine-reticulate, as previously described, were also confirmed in the present study. Based on above study the evolution trends of pollen morphology in the taxa involved were discussed phylogenetically as below. As microechinate-perforate exine pattern existed commonly, the pattern is, therefore, regarded as the most primitive among all the six types. The fine-reticulate type was thought as a derivative type, deriving from the basic micro echinate-foveolate-perforate pattern, and followed by the rugulate and verrucate-perforate ornamentation. The verrucate-rugulate ornamentation should be the most advanced. More than one pollen type often exist in most of the sections in Rheum. The pollen morphology of Rheum was strongly correlated with its geographical and ecological distribution. Three medicinally important species R. officinale, R. palmation and R. tanguticum can be palynologically distinguished by their ornamentations.

大型反倾岩体变形破坏机制及稳定性分析———以金沙江宽谷坝址龙蟠边坡为例

A large number of catastrophic accidents were aroused by the instability and destruction of anti-dip rock masses in the worldwide engineering projects, such as hydropower station, mine, railways and so on. Problems in relation to deformation and failure about anti-dip rock slopes are significant for engineering geology research. This dissertation takes the Longpan slope in the Jinsha River as a case to study the deformation mechanism of large-scale anti-dip rock masses and the slope stability analysis method. The primary conclusions are as follows. The Dale Reach of Jinsha River, from Longpan to the debouchment of Chongjiang tributary, is located in the southeastern margin of the Qinghai-Tibet Plateau. Longpan slope is the right embankment of Dale dam, it is only 26 km to the Shigu and 18 km to Tiger Leaping Gorge. The areal geology tectonic structures here area are complicated and blurry. Base on the information of geophysical exploration (CSAMT and seismology) and engineering geological investigation, the perdue tectonic pattern of Dale Reach is put forward for the first time in this paper. Due to the reverse slip of Longpan fault and normal left-rotation of Baihanchang fault, the old faulted valley came into being. The thick riverbed sediments have layered characters of different components and corresponding causes, which attribute to the sedimentary environments according with the new tectonic movements such as periodic mountain uplifting in middle Pleistocene. Longpan slope consists of anti-dip alternate sandstone and slate stratums, and the deformable volume is 6.5×107m3 approximately. It was taken for an ancient landslide or toppling failure in the past so that Dale dam became a vexed question. Through the latest field surveying, displacement monitoring and rock masses deforming characters analyses, the geological mechanism is actually a deep-seated gravitational bending deformation. And then the discrete element method is used to simulate the deforming evolution process, the conclusion accords very well with the geo-mechanical patterns analyses. In addition strength reduction method based on DEM is introduced to evaluate the factor of safety of anti-dip rock slope, and in accordance with the expansion way of the shear yielding zones, the progressive shear failure mechanism of large-scale anti-dip rock masses is proposed for the first time. As an embankment or a close reservoir bank to the lower dam, the stability of Longpan slope especially whether or not resulting in sliding with high velocity and activating water waves is a key question for engineering design. In fact it is difficult to decide the unified slip surface of anti-dip rock slope for traditional methods. The author takes the shear yielding zones acquired form the discrete element strength reduction calculation as the potential sliding surface and then evaluates the change of excess pore pressure and factor of stability of the slope generated by rapid drawdown of ponded water. At the same time the dynamic response of the slope under seismic loading is simulated through DEM numerical modeling, the following results are obtained. Firstly the effective effect of seismic inertia force is resulting in accumulation of shear stresses. Secondly the discontinuous structures are crucial to wave transmission. Thirdly the ultimate dynamic response of slope system takes place at the initial period of seismic loading. Lastly but essentially the effect of earthquake load to bringing on deformation and failure of rock slope is the coupling effect of shear stresses and excess pore water pressure accumulation. In view of limitations in searching the critical slip surface of rock slope of the existing domestic and international software for limit equilibrium slope stability analyses, this article proposes a new method named GA-Sarma Algorithm for rock slope stability analyses. Just as its name implies, GA-Sarma Algorithm bases on Genetic Algorithm and Sarma method. GA-Sarma Algorithm assumes the morphology of slip surface to be a broken line with traceability to extend along the discontinuous surface structures, and the slice boundaries is consistent with rock mass discontinuities such as rock layers, faults, cracks, and so on. GA-Sarma Algorithm is revolutionary method that is suitable for global optimization of the critical slip surface for rock slopes. The topics and contents including in this dissertation are closely related to the difficulties in practice, the main conclusions have been authorized by the engineering design institute. The research work is very meaningful and useful for the engineering construction of Longpan hydropower station.

生物－热催化过渡带沉积成岩演化及其成烃作用研究

The biothermocatalytic transitional zone gas is a new type of natural gas genetic theory, and also an clean, effective and high quality energy with shallow burial depth, wide distribution and few investment. Meanwhile, this puts biothermocatalytic transitional zone gas in important position to the energy resource and it is a challenging front study project. This paper introduces the concept, the present situation of study and developmental trend about biothermocatalytic transitional zone gas in detail. Then by using heat simulating of source rocks and catalysis mechanism analysis in the laboratory and studying structural evolution, sedimentation, diagenesis and the conditions of accumulation formation and so on, this paper also discusses catalytic mechanism and evolutionary model of the biothermocatalytic transitional zone gas formation, and establishes the methods of appraisal parameter and resources prediction about the biothermocatalytic transitional zone gas. At last, it shows that geochemical characteristics and differentiated mark of the biothermocatalytic transitional zone gas, and perfect natural gas genetic theory, and points out the conditions of accumulation formation, distribution characteristics and potential distribution region on the biothermocatalytic transitional zone gas m China. The paper mainly focuses on the formation mechanism and the resources potential about the biothermocatalytic transitional zone gas. Based on filed work, it is attached importance to a combination of macroscopic and microcosmic analysis, and the firsthand data are obtained to build up framework and model of the study by applying geologic theory. Based on sedimentary structure, it is expounded that structural actions have an effect on filling space and developmental cource of sediments and evolution of source rocks. Carried out sedimentary environment, sequence stratigraphy, sedimentary system and diagenesis and so on, it is concluded that diagenesis influences developmental evolution of source rocks, and basic geologic conditions of the biothermocatalytic transitional zone gas. Applying experiment simulating and catalytic simulating as well as chemical analysis, catalytic mechanism of clay minerals is discussed. Combined diagenecic dynamics with isotope fractionation dynamics, it is established that basis and method of resource appraisal about the biothermocatalytic transitional zone gas. All these results effectively assess and predict oil&gas resources about the biothermocatalytic transitional zone gas-bearing typical basin in China. I read more than 170 volumes on the biothermocatalytic transitional zone gas and complete the dissertation' summary with some 2.4 ten thousand words, draw up study contents in some detail and set up feasible experimental method and technologic course. 160 pieces of samples are obtained in oilfield such as Liaohe, Shengli, Dagang and Subei and so on, some 86 natural gas samples and more than 30 crude oil samples. Core profiles about 12 wells were observed and some 300 geologic photos were taken. Six papers were published in the center academic journal at home and abroad. Collected samples were analysised more than 1000 times, at last I complete this dissertation with more than 8 ten thousand words, and with 40 figures and 4 plates. According to these studies, it is concluded the following results and understandings. 1. The study indicates structural evolution and action of sedimentary basin influence and control the formation and accumulation the biothermocatalytic transitional zone gas. Then, the structural action can not only control accommodation space of sediments and the origin, migration and accumulation of hydrocarbon matters, but also can supply the origin of energy for hygrocarbon matters foramtion. 2. Sedimentary environments of the biothermocatalytic transitional zone gas are lake, river and swamp delta- alluvial fan sedimentary systems, having a warm, hot and humid climate. Fluctuation of lake level is from low to high., frequency, and piling rate of sedimentary center is high, which reflect a stable depression and rapidly filling sedimentary course, then resulting in source rocks with organic matter. 3. The paper perfects the natural gas genetic theory which is compound and continuous. It expounds the biothermocatalytic transitional zone gas is a special gas formation stage in continuous evolutionary sequence of organic matter, whose exogenic force is temperture and catalysis of clay minerals, at the same time, having decarbxylation, deamination and so on. 4. The methodology is established which is a combination of SEM, TEM and Engery spectrum analysis to identify microstructure of crystal morphology about clay minerals. Using differential thermal-chromatographic analysis, it can understand that hydrocarbon formation potential of different typies kerogens and catalytic method of all kinds of mineral matrix, and improve the surface acidity technology of clay minerals measured by the pyridine analytic method. 5. The experiments confirm catalysis of clay minerals to organic matter hygrocarbon formation. At low temperature (<300 ℃), there is mainly catalysis of montmorillonite, which can improve 2-3 times about produced gas of organic matters and the pyrolyzed temperature decreased 50 ℃; while at the high temperature, there is mainly catalysis of illite which can improve more than 2 times about produced gas of organic matters. 6. It is established the function relationship between organic matter (reactant) concentration and temperature, pressure, time, water and so on, that is C=f (D, t). Using Rali isotope fractionation effect to get methane isotope fractionation formula. According to the relationship between isotope fractionation of diagenesis and depth, and combined with sedimentary rate of the region, it is estimated that relict gas of the biothermocatalytic transitional zone gas in the representative basin. 7. It is revealed that hydrocarbon formation mechanism of the biothermocatalytic transitional zone gas is mainly from montmorillonite to mixed minerals during diagenesis. In interlayer, a lot of Al~(3+) substitute for Si~(4+), resulting in a imbalance between surface charge and interlayer charge of clay minerals and the occurrence of the Lewis and Bronsted acid sites, which promote to form the carbon cation. The cation can form alkene or small carbon cation. 8. It is addressed the comprehensive identification mark of the biothermo - catalytic transitional zone gas. In the temproal-spatial' distribution, its source rocks is mainly Palaeogene, secondly Cretaceous and Jurassic of Mesozoic, Triassic, having mudy rocks and coal-rich, their organic carbon being 0.2% and 0.4% respectively. The vitrinite reflection factor in source rocks Ro is 0.3-0.65%, a few up to 0.2%. The burial depth is 1000-3000m, being characterized by emerge of itself, reservoir of itself, shallow burial depth. In the transitional zone, from shallow to deep, contents of montmorillonites are progressively reduced while contents of illites increasing. Under SEM, it is observed that montmorillonites change into illite.s, firstly being mixed illite/ montmorillonite with burr-like, then itlite with silk-like. Carbon isotope of methane in the biothermocatatytic transitional zone gas , namely δ~(13)C_1-45‰- -60 ‰. 9. From the evolutionary sequence of time, distribution of the biothermocatalytic transitional zone gas is mainly oil&gas bearing basin in the Mesozoic-Neozoic Era. From the distribution region, it is mainly eastern stuctural active region and three large depressions in Bohaiwang basin. But most of them are located in evolutionary stage of the transitional zone, having the better relationship between produced, reservoir and seal layers, which is favorable about forming the biothermocatalytic transitional zone gas reservoir, and finding large gas (oil) field.

Mesoporous spinel MgAl2O4 prepared by in situ modification of boehmite sol particle surface: I Synthesis and characterization of the unsupported membranes

Mesoporous spinel membranes as ultrafiltration membranes were prepared through a novel sol-gel technique. By in situ modification of the sol particle surface during the sol-gel process, control of the material structure on a nanometer scale from the earliest stages of processing was realized. Nano-particles with a chocolate-nut-like morphology, i.e. spinel MgAl2O4 as a shell and gamma -Al2O3 as a core, were first revealed by HRTEM results. The formation of the spinel phase was confirmed by X-ray diffraction (XRD). N-2 adsorption-desorption results showed that the mesoporous membranes had a narrow pore size distribution. (C) 2001 Elsevier Science B.V. All rights reserved.

Coadsorption of nitric oxide and oxygen on the Ag(110) surface

The coadsorption of NO and O-2 on Ag(110) surface has been studied by X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS) and in situ Raman spectroscopy. The existence of oxygen enhances the adsorption of NO by forming the NOx species, that is, NO2 and NO3, and the NO in turn as a promotor facilitates the cleavage of the dioxygen bond, forming the surface atomic oxygen species having the same spectral characteristics as those produced using oxygen at high pressure. The oxygen species generated by the interaction is composed of two parts. One is produced directly by the decomposition of surface NO-O-2 complex at ca 625 K, which raised an O 1s feature at 530.5 eV and is absent at ca 800 K, while the another with an O 1s binding energy of 529.2 eV emerges at higher temperatures and shows similar properties as the reported gamma-state oxygen which bound tightly on restructured silver surface. The exposure to NO and O-2 causes noticeable changes in the morphology of the Ag(110) surface and the flat terraces superseded by small (ca 0.1 mu m) pits, and particles with typical diameters of a few micrometres were formed at elevated temperatures. (C) 1999 Elsevier Science B.V. All rights reserved.