Analysis of mussel standard reference material by inductively coupled plasma atomic emission spectrometry and inductively coupled plasma mass spectrometry

A method for the analysis of mussel standard reference material by inductively coupled plasma atomic emission spectrometry( ICP-AES) and inductively coupled plasma mass spectrometry(ICP-MS) was developed. K, Na, Ca, Mg, P, Al, Fe, Zn, Mn and Sr were determined by ICP-AES and As, B, Cd, Co, Cr, Cu, Ga, Ge, Mn, Mo, Ni, Pb, Se, Sr, U and V by ICP-MS, The interference coefficients at the Mn-55, Se-78, Cu-63, Co-59, Ni-58, Ni-60, As-75, Se-77, V-51, Cr-53 and Cr-52 originating from polyatomic ion of the matrix elements (KO)-K-39-O-16, K-39(2), (ArNa)-Ar-40-Na-23, (CaO)-Ca-43-O-16, (CaO)-Ca-42-O-16, (CaO)-Ca-44-O-16, (PO2)-P-31-O-16, (ArCl)-Ar-40-Cl-35, (ArCl)-Ar-40-Cl-37, (ClO)-Cl-35-O-16, (ClO)-Cl-37-O-16 and (ArC)-Ar-40-C-12 were determined under the selected operation parameters. The major matrix elements, such as K, Na and Ca, result in the suppression of analytes signals. The apparent concentration at the significant biological element which was produced by the different digestion methods, (.) HNO3 + H2O2 (3 + 2), HNO3 + HClO4 (3 + 0.5) and HNO3 + H2SO4 (3 + 0.5),was determined. The sample digested by HNO3 + H2O2 did not give rise to interfere on the analyte, and the backgrounds of Se-77, Ga-69, Zn-67, As-75, V-51, Cr-53 and Cr-52 were increased by HNO3 + HClO4 digestion method, that affected the determination of these elements, especially the monoisotope As and V. Sample digested by HNO3 + H2SO4 increased the backgrounds at Cu-65, Zn-64 and Zn-67. Detection limits of ICP-AES are 0.001 similar to 0.75 mg/L and those of ICP-MS are 0.005 similar to 1.01 mu g/L. The relative standard derivations of ICP-AES and ICP-MS are 2.7% similar to 12.8%, 3.4% similar to 24.8%, respectively.

Functionalized inorganic-organic composite material derivated by sol-gel for construction of mediated amperometric hydrogen peroxide biosensor

A novel functionalized inorganic-organic hybrid material with cation exchange property was prepared by sol-gel method. The H2O2 biosensor was fabricated by simply dipping the horseradish peroxidase-containing functionalized membrane modified electrode into Meldola's blue (MDB) solution. MDB was adsorbed and firmly immobilized within the membrane. The electrochemical behavior of MDB incorporated in the membrane was more reversible compared with that of the solution species and suitable as mediator for the horseradish peroxidase. The response time was less than 25 s. Linear range is up to 0.6 mM (COH. coeff. 0.9998) with detection Limit of 9 x 10(-7) M. High sensitivity of 75 nA mu M cm(-2) was obtained due to high MDB-loading. The biosensor exhibited a good stability. (C) 1999 Elsevier Science B.V. All rights reserved.

A new high efficiency green luminescent material - the system Al2O3-B2O3 containing Ce3+ and Tb3+ ions

To obtain high efficiency luminescent materials, the system Al2O3-B2O3 containing Ce3+ and Tb3+ ions with variation of B2O3-content, has been prepared by Al2O3, H3BO3, CeO2 and Tb4O7 under reducing atmosphere at 1250(j)ae. It is notable that the brightness of the sample with appropriate composition is similar to that of commercial phosphorous containing Ce3+ and Tb3+, indicating that a new high efficency green luminescent material was obtained with appropriate B2O3-content.

Amperometric glucose biosensor based on sol-gel organic-inorganic hybrid material

A new type of sol-gel organic-inorganic hybrid material was developed and used for the production of biosensors. This material is composed of silica sol and a grafting copolymer of poly(vinyl alcohol) with 4-vinylpyridine. It prevents the cracking of conventional sol-gel-derived glasses and eliminates the swelling of the hydrogel. The optimum composition of the hybrid material was first examined, and then glucose oxidase was immobilized in this matrix to demonstrate its application. The characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The biosensor exhibited a series of good properties: high sensitivity (600 nA mmol(-1)L(-1)), short response time (11 s) and remarkable long-term stability in storage (at least 5 months). In addition, the characteristics of the second-generation biosensor with the use of tetrathiafulvalene as a mediator mere discussed.

Surface roughness characterization of soft x-ray multilayer films on the nanometer scale

The soft x-ray reflectivity of multilayer films is affected by the surface roughness on the transverse nanometer scale. Scanning tunneling microscopy (STM) is an ideal instrument for providing high-lateral-resolution roughness measurements for soft x-ray multilayer films that cannot be obtained with other types of instruments on the transverse nanometer scale. The surface roughnesses of Mo/Si, Mo/C, and W/Si soft x-ray multilayer films prepared by an ion-beam-sputtering technique were measured with a STM on the vertical and transverse attributes. The film roughnesses and average spatial wavelengths added to the substrates depend on the multilayer film fabrication conditions, i.e., material combinations, number of layers, and individual layer thickness. These were estimated to lead to a loss of specular reflectivity and variations of the soft x-ray scattering angle distribution. This method points the way to further studies of soft x-ray multilayer film functional properties and can be used as basic guidance for selecting the best coating conditions in the fabrications of soft x-ray multilayer films. (C) 1996 American Vacuum Society.

STUDY ON THE NON-STIOCHIOMETRIC SNO2-X NANOCRYSTALLINE MATERIAL BY XRD, XPS AND ESR

Nonstiochiometric SnO2-x nanocrystalline material were successfully prepared through Sol-Gel process using anhydrous stannic chloride and iso-propyl alcohol. TEM observation shows that the mean diameter of the powder sintered at 700 degrees C for 2 hours is about 20 nm. By the investigation of XRD and ESR, we can conclude that the sample sintered at 300 degrees C for 2 hours was amorphous and it grew into nanocrystalline with the oxygen vacancies and defects when sintered at 700 degrees C for 2 hours. Using these conclusion, the ESR signals and the difference between the two SnO2-x samples are explained.

Bioorganic/inorganic hybrid composition of sponge spicules: Matrix of the giant spicules and of the comitalia of the deep sea hexactinellid Monorhaphis

The giant basal spicules of the siliceous sponges Monorhaphis chuni and Monorhaphis intermedia (Hexactinellida) represent the largest biosilica structures on earth (up to 3 m long). Here we describe the construction (lamellar organization) of these spicules and of the comitalia and highlight their organic matrix in order to understand their mechanical properties. The spicules display three distinct regions built of biosilica: (i) the outer lamellar zone (radius: >300 mu m), (ii) the bulky axial cylinder (radius: <75 mu m), and (iii) the central axial canal (diameter: <2 mu m) with its organic axial filament. The spicules are loosely covered with a collagen net which is regularly perforated by 7-10 mu m large holes; the net can be silicified. The silica layers forming the lamellar zone are approximate to 5 mu m thick; the central axial cylinder appears to be composed of almost solid silica which becomes porous after etching with hydrofluoric acid (HF). Dissolution of a complete spicule discloses its complex structure with distinct lamellae in the outer zone (lamellar coating) and a more resistant central part (axial barrel). Rapidly after the release of the organic coating from the lamellar zone the protein layers disintegrate to form irregular clumps/aggregates. In contrast, the proteinaceous axial barrel, hidden in the siliceous axial cylinder, is set up by rope-like filaments. Biochemical analysis revealed that the (dominant) molecule of the lamellar coating is a 27-kDa protein which displays catalytic, proteolytic activity. High resolution electron microscopic analysis showed that this protein is arranged within the lamellae and stabilizes these surfaces by palisade-like pillars. The mechanical behavior of the spicules was analyzed by a 3-point bending assay, coupled with scanning electron microscopy. The load-extension curve of the spicule shows a biphasic breakage/cracking pattern. The outer lamellar zone cracks in several distinct steps showing high resistance in concert with comparably low elasticity, while the axial cylinder breaks with high elasticity and lower stiffness. The complex bioorganic/inorganic hybrid composition and structure of the Monorhaphis spicules might provide the blueprint for the synthesis of bio-inspired material, with unusual mechanical properties (strength, stiffness) without losing the exceptional properties of optical transmission. (C) 2007 Elsevier Inc. All rights reserved.

Geochemical character and material source of sediments in the eastern Philippine Sea

Based upon analyses of grain-size, rare earth element (REE) compositions, elemental occurrence phases of REE, and U-series isotopic dating, the sediment characteristics and material sources of the study area were examined for the recently formed deep-sea clays in the eastern Philippine Sea. The analytical results are summarized as follows. (1) Low accumulation rate, poor sorting and roundness, and high contents of grains coarser than fine silt indicate relatively low sediment input, with localized material source without long distance transport. (2) The REE Contents are relatively high. Shale-normalized patterns of REE indicate weak enrichment in heavy REE (HREE), Ce-passive anomaly, and Eu-positive anomaly. (3) Elemental occurrence phases of REE between the sediments with and without crust are similar. REE mainly concentrate in residual phase and then in ferromanganese oxide phase. The light REE (LREE) enrichment, Ce-positive anomaly, and Eu-positive anomaly occur in residual phase. Ferromanganese oxide phase shows the characteristics of relatively high HREE content and Ce-passive anomaly. (4) There are differences in each above mentioned aspect between the sediments with and without ferromanganese crust. (5) Synthesizing the above characteristics and source discriminant analysis, the study sediments are deduced to mainly result from the alteration of local and nearby volcanic materials. Continental materials transported by wind and/or river (ocean) flows also have minor contributions.

Mineral provinces and material provenance of the surficial sediments near the Zhongsha Islands in the South China Sea

Characteristics and distribution patterns of elastic minerals (0.063 similar to 0.125 mm) in bottom sediments represent a significant indicator for the identification of the origin of sediment. One hundred and fourteen surface sediment samples, which were collected from the area near the Zhongsha Islands in the South China Sea, were analysed to identify the mineral suites and their distributions in the study area. The area can be divided into three mineral provinces: ( I) a province of biogenic minerals, which mainly originate from the Zhongsha Atoll; ( H) a province of volcanogenic minerals, which are mainly derived from local basaltic seamounts and small-scale volcanoes that are probably erupting, with some influences from the island-are volcanic region around the South China Sea; and (II) a mixed mineral province whose material source includes biogenic minerals, volcanogenic minerals and terrigenous minerals; the last province can be subdivided into a mixed mineral sub-province of the northeastern part of the study area, in which terrigenous minerals are mainly derived from China's Mainland and do not exceed 17 degrees N, and a mixed mineral sub-province of the southeastern part of the study area, in which terrigenous minerals are derived from Kalimantan and Indochina Peninsula and might be further transported into the deep sea basin through submarine canyons.

Effective dielectric response of composites witli graded material

The effective dielectric response of linear composites containing graded material is investigated under an applied electric field Eo. For the cylindrical inclusion with gradient dielectric function, epsilon(i)(r) = b + cr, randomly embedded in a host with dielectric constant epsilon(m), we have obtained the exact solution of local electric potential of the composite media regions, which obeys a linear constitutive relation D = epsilonE, using hypergeometric function. In dilute limit, we have derived the effective dielectric response of the linear composite media. Furthermore, for larger volume fraction, the formulas of effective dielectric response of the graded composite media, are given.

Organic geochemical studies of sinking particulate material in China sea area(I) - Organic matter fluxes and distributional features of hydrocarbon compounds and fatty acids

Sinking particulate material collected from Nansha Yongshu reef lagoon and the continental shelf of the East China Sea by sediment traps has been analyzed and studied for the first time using organic geochemical method. The results show that about half of the sinking particulate organic matter in the two study areas are consumed before reaching the depth of 5 m to the sea floor and the degree of this consumption in Yongshu reef lagoon is larger than that in the continental shelf of the East China Sea. The distributions of hydrocarbons and fatty acids indicate that the minor difference of biological sources of sinking particulate organic matter exists between Yongshu reel lagoon and the continental shelf of the East China Sea, but they mainly come from marine plankton. Stronger biological and biochemical transformations of sinking particulate organic matter are also observed and the intensity of this transformation in Yongshu reef lagoon is greater than that in the continental shelf of the East China Sea. It is found that the occurrence of C-25 highly branched isoprenoid (HBI) diene may be related to the composition of diatom species.

Formation of nano-crystalline corrosion products on Zn-Al alloy coating exposed to seawater

Hot dip Zn-Al alloy coating performs better than hot dip galvanized coating and 55% Al-Zn-Si coating as well with regard to general seawater corrosion protection. A characterization of the corrosion products on Zn-Al alloy coating immersed in dynamic aerated seawater has been performed mainly based on transmission electron microscopy (TEM) for morphological analysis and X-ray diffraction (XRD) technique for crystalline phase identification. The XRD and TEM analyses showed that the corrosion products mainly were typical nanometer Zn4CO3(OH)(6).H2O, Zn-5(OH)(8)Cl-2 and Zn6Al2CO3(OH)(16). 4H(2)O microcrystals. This probably is connected to the co-precipitation of Zn2+ and Al3+ ions caused by adsorption. Zn-Al alloy coating being suffered seawater attacks, AI(OH)(3) gel was first produced on the coating surface. Zn and Al hydroxides would co-precipitate and form double-hydroxide when the concentration of adsorbed Zn2+ ions by the newly produced gel exceeded the critical degree of supersaturation of the interphase nucleation. However, because the growth of the crystals was too low to keep in step with the nucleation, a layer of nano-crystalline corrosion products were produced on the surface of the coating finally. (C) 2001 Elsevier Science Ltd. All rights reserved.

Study on growth factors of intermetallic layer within hot-dipped 25% Al-Zn alloy coating on steel

25%Al-Zn alloy coating performs better than hot dip galvanized coating and 55%Al-Zn-Si coating with regard to general seawater corrosion protection. This study deals with the interfacial intermetallic layer's growth, which affects considerably the corrosion resistance and mechanical properties of 25%Al-Zn alloy coatings, by means of three-factor quadratic regressive orthogonal experiments, The regression equation shows that the intermetallic layer thickness decreases rapidly with increasing content of Si added to the Zn-Al alloy bath, increases with rise in bath temperature and prolonging dip time. The most effective factor that determined the thickness of intermetallic layer was the amount of Si added to Zn-Al alloy bath, while the effect of bath temperature and dip time on the thickness of intermetallic layer were not very obvious.