Kilohertz electro-optic Q-switched Nd : YAG ceramic laser

We investigate the lasing characteristics of a laser-diode-array side-pumped electro-optic Q-switched Nd:Y3Al5O12 ceramic laser operating at 1000 Hz pulse repetition rate. Using a YAG poltcrystalline rod with Nd3+ concentration at 1 at.% as the gain medium, pumping with 808 nm laser-diode-arrays, the Q-switched laser output at 1064 nm wavelength with 23 mJ pulse energy and less than 12 ns FWHM pulse width are obtained at a pumping power of about 400 W, the slope efficiency is around 15%, the output beam divergence angle is about 1.2 mrad.

The influence of OH groups on laser performance in phosphate glasses

Because of the influence of OH groups in phosphate glasses on the radiation of rare-earth ions, the laser performance is degraded. The laser efficiency and the small signal gain experiment of several phosphate glass samples have been done, the concentration of OH groups in glasses was calculated from the measured absorption coefficient at 3.47 μm. It is shown that the concentration of OH groups in phosphate glasses can seriously influence the laser output characteristics, and the OH groups have worse influence on the laser amplifier than laser oscillator.

A 20.1 W Solid-State Laser Pumped by 887 nm with High Efficiency and TEM00 Mode

High efficiency, TEM00 mode, high repetition rate laser pumped by 887 nm is reported. 20.1 W output laser emitting at 1064 nm is achieved in a 0.3 at % Nd-doped Nd:YVO4, which absorbs pumping light of 30.7 W at 887 nm. The opto-optic efficiency and the slope efficiency are 65.5 and 88.5%, respectively. The stable Q-switching operation worked well at 100 kHz and the beam quality is near diffraction-limit with M-2 factor measured as M-2 approximate to 1.2. And the pulse waveform is analyzed in this paper.

880 nm LD pumped passive mode-locked TEM00 Nd:YVO4 laser based on SESAM

We report on an 880 nm LD pumped passive mode-locked TEM00 Nd:YVO4 laser based on a semiconductor saturable absorber mirror (SESAM) for the first time. When the incident pump power was 16 W, 4.76 W average output power of continuous-wave mode-locked laser with an optical-to-optical conversion efficiency of 30% was achieved. The repetition rate of mode-locked pulse was 80 MHz with 25 ps pulse width. The maximum pulse energy and peak power were 60 nJ and 2.4 kW, respectively.

1kHz-0．1TW高效率钛宝石激光放大器

介绍了一种高重复频率掺钛蓝宝石飞秒激光多通高效率放大系统．在抽运功率为23W，入射功率为660mW时，获得7．2W的放大输出，放大效率达30％．经压缩器压缩后，获得单脉冲能量4．5mJ，脉冲宽度为38fs，重复频率为1kHz，峰值功率大于0．1TW的超短超强激光脉冲．

Core size scaling of helical-core optical fibres

The mode-area, scaling properties of helical-core optical fibres are numerically studied and the limit of core size for achievable single-mode operation is explored. By appropriate design, helical-core fibres can operate in a single mode with possible scaling up to 300 mu m in core diameter with numerical aperture 0.1.

板条热容激光器的二维热特性

固体热容激光器（SSHCL）作为高功率固体激光器的一个重要发展方向,引起人们广泛关注。数值模拟激光介质板条在热容方式下工作的温度和应力分布是了解该类激光器工作特性的一种有效手段,采用平面应力近似法导出了半导体激光器抽运热容激光介质板的二维温度和应力分布公式,同时也对二维抽运光吸收密度、介质板温度分布和折射率变化进行了分析与讨论。数值计算的结果表明二维效应的温度分布和应力分布要比一维效应给出的分布更均匀。

热容型板条激光器的感应折射率计算

高平均功率固体激光器的增益介质由于受热而容易发生畸变,如常用材料YAG,波前畸变和去偏振现象会同时发生,高热负载固体激光介质的热效应已成为制约激光器输出功率进一步提高的严重障碍。给出一种计算热容型板条激光器热感生折射率的方法。把YAG晶体的四阶压光张量从晶胞坐标系转换到实验室坐标系,采用经过坐标转换后的新的张量,可以分析在YAG激光器中任意应力分布引起的热感应双折射。进一步的计算表明,在zigzag板条激光器中,应力双折射率与板条从晶体毛胚上切割成材的角度有关。同时也对热容板条激光器的热效应和应力特性进行了二维的理论性概述。

激光束质量实时测量技术

提出一种新型光束质量实时测量技术, 该技术主要基于由平板反射镜组成的多平面成像系统, 一次性将激光束腰附近2倍瑞利距离内的多个光斑成像在同一个平面上, 用CCD相机获取这些光斑的光强分布图样。通过图像处理获知接收到的光斑的光强分布。采用远场发散角、焦点尺寸、桶中功率比和M2因子四种光束质量评价标准对激光光束质量进行评价。利用该方法实时测量了高能钕玻璃双板条激光器的输出光束。

高重复率半导体激光抽运Nd：YAG放大器激光特性的实验研究

实验研究了高重复率、大功率半导体激光二极管阵列（LDA）侧面环绕抽运的Nd：YAG激光放大器的放大特性、热焦距变化和热致双折射效应引起的退偏特性。偏振光绎千赫兹高功率单通激光放大器，获得约3倍的光脉冲能量放大，脉冲宽度基本保持不变，其输出的P分量与S分量的能量比趋于常数3：1，实验测得的能量放大倍率及放大光束的椭圆偏振度与理论预期吻合很好。

高功率板条激光器的研究进展

板条激光器，特别是LD抽运的板条激光器，作为高功率同体激光器的一个重要发展方向，在军用和工业应用等领域有着较好的应用前景。综述了板条激光器的抽运、冷却方式以及谐振腔设计方面的进展，并对其应用前景进行展望。

双侧面90°抽运微通道致冷Yb：YAG板条激光器

报道了采用带有微柱镜的激光二极管阵列（LDA）双侧面90°排布抽运的Yb：YAG板条激光器，实验中使用的激光晶体尺寸为6mm×10mm×1mm，掺杂原子数分数为3％。抽运光通过自行设计的聚光系统聚焦成10mm×1mm的光斑进行抽运，聚光系统的效率为75％，晶体表面功率密度达到1．9kW／cm^2，晶体内抽运光交叠区的体功率密度达到38kW／cm^3，远高于阈值的1．7kW／cm^3。当激光器采用平一凹腔结构，耦合输出为6％时激光单脉冲输出能量最高为25．5mJ，斜率效率为13％。插入声光调Q晶体后获得4．

部分端面抽运板条激光器腔镜倾斜问题研究

部分端面抽运的板条激光器是一种新型固体激光器．配合混合腔可以实现在大功率下保持高光束质量的激光振荡输出。谐振腔的腔镜倾斜是影响激光器输出特性的重要因素，快速傅里叶方法是一种快捷有效的计算方法，利用此方法模拟了腔镜倾斜对近场相位分布和远场光强分布的影响，并分析了光束质量的变化。理论分析表明，腔镜的小角度倾斜对近场相位影响较大，但对远场光强空间分布影响不大；随着倾斜角度不断增大，远场发散角和光束腰宽度也增大，光束质量虽然存在恶化的趋势，但光束质量因子肝值仍然较小，离轴非稳腔仍能保持高光束质量的输出。

千瓦级半导体抽运的固体热容板条激光器

报道了千瓦级激光二极管面阵抽运固体热容激光器的理论与实验研究, 分别采用Nd:YAG单板条和双板条串接的热容激光器, 利用热容激光器的理论计算模型计算了在一定的工作时间内激光输出特性, 并进行了实验验证。实验中采用的晶体尺寸均为59 mm×40 mm×4.5 mm, 对单板条进行抽运时平均功率大约为5.6 kW, 双板条串接时为11.2 kW, 重复频率为1 kHz, 占空比为20％。实验中观察了1 s的工作时间内脉冲能量输出的波动情况, 单板条时单脉冲能量输出最大为1.3 J, 在1 s后单脉冲能量输出

新一代大功率固体板条激光器的技术进展

介绍了固体板条激光器为了获得大功率和高光束质量而采用的新技术, 阐述了新一代大功率固体板条激光器的最新进展, 分析了新一代大功率固体板条激光器的技术特点, 并对其应用前景进行了展望。