Species transformation of trace elements and their distribution prediction in dyestuff residue incineration

The release of heavy metals from the combustion of hazardous wastes is an environmental issue of increasing concern. The species transformation characteristics of toxic heavy metals and their distribution are considered to be a complex problem of mechanism. The behavior of hazardous dyestuff residue is investigated in a tubular furnace under the general condition of hazardous waste pyrolysis and gasfication. Data interpretation has been aided by parallel theoretical study based on a thermodynamic equilibrium model based on the principle of Gibbs free energy minimization. The results show that Ni, Zn, Mn, and Cr are more enriched in dyestuff residue incineration than other heavy metals (Hg, As, and Se) subjected to volatilization. The thermodynamic model calculation is used for explaining the experiment data at 800 degrees C and analyzing species transformation of heavy metals. These results of species transformation are used to predict the distribution and emission characteristics of trace elements. Although most trace element predictions are validated by the measurements, cautions are in order due to the complexity of incineration systems.

采油污水回注系统缓蚀阻垢技术研究

油田腐蚀与结垢是油田生产面临的普遍问题。随着油田开发时间的延长，注水开采成为普遍采用的采油工艺。因此，腐蚀与结垢问题十分突出。腐蚀和结垢现象的存在，增大了油田生产成本，给开发生产造成惨重的经济损失，是制约油田高效益、低投入快速发展的关键因素之一。 本文以辽河油田采油污水为研究对象。在水质特征和垢样组成分析的基础上，明确了腐蚀结垢原因。以六偏磷酸钠（(NaPO3)6）和硫酸锌（ZnSO4•7H2 O）为缓蚀剂，以氨基三亚甲基膦酸（ATMP）和羟基亚乙基二膦酸（HEDP）为阻垢剂，添加少量聚合物分散剂筛选复配出具有缓蚀、阻垢和分散等功能的高效复合缓蚀阻垢剂。研究了缓蚀剂含量、添加聚合物分散剂、药剂浓度、油田其他助剂等对缓蚀阻垢剂性能的影响，并探讨了药剂的缓蚀阻垢机制。 针对高升采油厂和沈阳采油厂的注水水质，筛选复配的缓蚀阻垢剂最佳配比及投加浓度为：(NaPO3)6，11.2mg/L； ZnSO4•7H2O，16.8mg/L；HEDP，7.2mg/L；ATMP，4.8mg/L；水解聚马来酸酐（HPMA）或丙烯酸/丙烯酸羟丙酯/AMPS共聚物（W-118A），5.0mg/L。总浓度为45mg/L。 室内动态模拟实验结果表明，复配缓蚀阻垢剂缓蚀率和阻垢率达99%以上，腐蚀速率低于0.02mm/a，具有优良的缓蚀阻垢性能。药剂性能评价结果表明该复合缓蚀阻垢剂具有耐高温、投加剂量低，与油田其他助剂配伍性好，低磷环保等优点。 现场试验和推广应用研究结果表明，筛选复配的缓蚀阻垢剂适合于辽河油田采油污水回注系统，腐蚀速率从以前的1.135mm/a降低到0.038mm/a，缓蚀率和阻垢率均达到96%以上，能够达到辽河油田采油污水回注系统防腐阻垢控制目标的要求，并且腐蚀速率也低于国家石油化工行业标准的防腐阻垢控制要求（≤0.075mm/a）。 通过经济效益分析表明，采用该项工艺技术经济效益显著，具有较好的推广应用前景。

无粪便生活污水SMBR快速处理技术研究

针对传统生活污水水质相对复杂，处理与回用较为困难的问题，提出在搜集时排除粪便水，选择厨房、洗漱、洗澡、洗涤的污水，利用浸没式膜生物反应器（SMBR）技术实现上述类型污水的快速处理，再生水回用于冲厕。研究结果表明：此种污水COD、NH4+-N和TP含量低，具有良好的可生化性，可大大降低处理周期与处理成本。本技术优化的主要工艺条件为：污泥浓度范围7000～9100 mg•L-1，污泥龄40～55d，HRT为80min，气水比为12～15:1，处理效果好，微滤膜对稳定出水水质起到重要作用。在此条件下，COD、NH4-N,TP去除率分别为85.47%, 53.11%,44.86%。出水COD在20～30mg•L-1之间，BOD5为1～5 mg•L-1；NH4+-N为2～3.08 mg•L-1，TP为0.59～0.9mg•L-1 mg•L-1，LAS为0.41～0.67mg•L-1，去除效果较好，再生水水质可达到《城市污水再生利用 城市杂用水水质》(GB/T 18920- 2002)标准。本文研究不足之处主要是由于文章所述污水搜集难度较高，实验用水为模拟废水，在一定程度上与实际污水有差距。 本研究结果可为生活污水的处理与回用提供一种新的思路与研究基础。

碱法草浆造纸蒸煮黑液厌氧生物降解性及其主要微生物类群研究

造纸行业是造成我国水环境有机污染物的重要污染源之一，其水污染的特点是小厂多、草浆多、工艺落后、污染扩散面广、造成废 水排放量大，每年排放的废水量约39亿立方米，占全国工业废水排放量的1/6，其中有机污染物（以BOD5计）160万吨左右，约占全 国工业废水中有机污染物总量的1/4。尤以占全国制浆造纸行业90%以上的碱法草浆造纸厂的蒸煮黑液量大面广，除含有机物外，还 含有木质素、残碱、硫化物、氯化物等污染物，属于PH值高、色度深、难于治理的高浓度有机废水，对水体污染特别严重，各地要 求治理呼声很高，急待研究并尽快找出各种有效的治理途径。对于碱法草浆蒸煮，黑液高浓度废水的治理，有各种方法，根据国内 的研究进展和我们已有试验工作表明，最经济有效，具有实用价值，在生产上可获得成功是厌氧处理法。近10多年来，国外关于高 效厌氧处理技术研究进展迅速，并出现了多种多样的工艺设备，如高效厌氧生物反应器，并在实用化方面取得了很大成绩，建立了 生产性装置，达到了高负荷运行，效果良好。本试验是根据我们已有研究基础，针对我国国情，对小型制浆造纸厂水污染防治除了 开发碱回收及各种综合利用技术外，要特别加强废水(废液)实用技术研究的指导思想，本试验采用改进型的上流式厌氧污泥床反应 器，设计了两种试验方案，通过试验结果如下。1. 试验方案I—碱法草浆黑液酸化和厌氧发酵I号UASB反应器动态模型试验结果表 明：(1). 采用中温35℃±1℃高效厌氧反应器USAB内装有填料(陶粒)和三相分离器，具有保持高浓度生物量和防止污泥流失的特点 ，污泥浓度Vs 可达30%以上，因而具有高效、节能、产能、滞留期短的优点，当进水CODcr在7500-10000mg/l，HRT由7天缩短到3天 ，有机容积负荷在1.22gCODcr/l·d-3.43gCODcr/l·d时，CODcr平均去除率可达55%-45.5%，最高CODcr去除率可达60.2-63.5%， BOD5去除率可达75.9-83.2%,沼气容积产气率可达0.29-0.67l/l·d，每克CODcr转化为沼气产率达0.39-0.48l/gCODcr·d，CH4含量 65.8-75.5%。厌氧发酵出水再用化学法进行后处理脱除难降解的木质素，CODcr总去除率达80%以上。(2). 动态试验结果表明：采 用酸化—厌氧发酵处理黑液工艺合理，技术路线可行。2. 试验方案II—黑液用化学法(Hcl)去除木质素进行厌氧发酵，II号UASB反 应器动态模型试验结果表明：(1). 采用中温35℃±1℃高效厌氧反应器UASB(内有软填料)，当进水CODcr7000-13000mg/l左右，HRT 由6天缩短到1天，有机负荷由0.98gCODcr/l·d增加到11gCODcr/l·d时，COD平均去除率均可稳定在70-77%，BOD5去除率为87.3- 93.1%，沼气容积产气率0.21-2.6l/l·d，每克CODcr转化为沼气产率为0.39-0.48l/gCODcr·d，高的可达0.53l/gCODcr·d，转化 率较高，CH4含量63-70%。(2). 试验证明碱法草浆黑液物化预处理—厌氧发酵处理的技术路线也是可行的，工艺合理、效果较好。 在有条件的工厂可采用。3.厌氧发酵阶段几大类群微生物计数表明：(1). 当发酵工艺和运行处于相对稳定状态时，微生物群体的 组成也达到相对的稳定，各类微生物之间保持动态平衡关系。当产乙酸菌的数量为107-108个/ml时，产甲烷菌的数量为105-106 个/ml，当产乙酸菌数量为106-107个/ml时，产甲烷菌的数量为103-105个/ml。(2).稳态运行条件下，黑液预处理为甲烷发酵创造 了有利的生态环境，获得了较好的处理效果和较高的COD转化为沼气的产率0.39-0.48l/g·CODcr·d，反应器中形成较为稳定而数 量较下水污泥中高1-2个数量级的厌氧发酵微生物区系组成。这一结果为黑液厌氧发酵提供了微生物理论依据。Paper industry is one of the important pollution source of water environment in our country. Its character of water pollution is many small factories, much grass pulp, disadvantageous technique, large preading area of pullution. Its effluent makes up 1/6 of whole country's industry wastwater. Its organic pollutant accounts 1/4 of whole country's. Alkaline grass paper pulp effluent with pollutants such as ligoin, remaining alkali sulfide, chloride besides organic material, is a kind of high concentrate organic wastewater which has high PH walug, dark colour and is difficult in treatment. There is urgent require to find ways to treat the wastewater. There are different ways to treat alkaline paper grass pulp effluent. According to the research advances and our experiment work, the most economical and useful way is anaerobic degradation which was advanced quick in last ten years. In the control of waste water of small pulp paper mill, the study of wastewater utilization technology should be emphasized, besides alkaline retrieving and different kinds of comprehensive utilization technology. Our experiment used modified UASB(Upflow Anaerobic Sludge Blanket Reactor). Two kinds of plan were disgned. The results are lined below. 1. The first experiment plant-aciding black pulp effluent and methanogenic digestion. The dynamic model experiment results of I-UASB reactor showed: (1)The mesophilic(35℃±1℃)high effect UASB reactor having haydite and threee state seperation in it had the character of keeping high bioimass concentration and preventing losss of sludge. It had advantages of high effect, energe saving, energe prodcing and short HRT(Hydroulic retention time). When the influent COD was 7500-10000mg, HRT was shortened from 7 days to 3days, organic loading rate was 1.22g-3.43COD/l· d, the average COD removal efficiency was 55%-45%. The highest COD efficiency was 60.2-63.5%, BOD removal of 75.9 -83.4% was achieved. Biogass production rate were up to 0.29-0.67l/l·d. Biogass converted efficiency from every gram of COD could reach 0.39-0.48l/gCOD·d. Methane content was 65.0-75.5%. Chemical method was used to deplate lignin in anaerobic digestion effluent. Total COD removal efficiency could be more than 80%. (2)Using aciding annaerobic digestion to treat the black effluent was reseanable in technique and technology. 2. The second experiment plan-anaerobic digestion was used after the chemical method was used to deplate lignin in the black effluent. The result of dynamic experiment of II-UASB reactor showed: (1)High effect mesophilic (35℃±1℃)UASB reactor having soft slaffing in was used. When influent COD was about 7000-13000mg/l, HRT was shortened from 6 days to 1 day and organic loading rate was increased from 0.90 to 11g COD /l·d, average COD removal efficiency remained stable on 70-77%. BOD, removal efficiency was between 87.3-93.1%. Biogass production rate was 0.2-2.6l/l ·d .Biogass converted efficiency from a gram of COD was 0.39-0.481/gCOD·d with the high value of 0.53l/gCOD·d. Methane content was 63-70%. (2)The way that using physical, chemical Pre-treatment-anaerobic digestion to treat alkaline black effluent is feasible and can be used in some factories when the condition exists. 3. Counting of several class of microoganisms in anaerobic digestion stage showed: (1)As the disgestion was in stable motion, the compositon of microorganic colony could get relative stable. Dynamic balance was remaining among different kinds of microorganism such as methanogenic bacteria, Acidogenic bacteria, sulfate reducing bacteria, and heterotrophic bacteria. (2)Under stable motion, the pre-treatment of black effluent produced favourable eco-enviroment for methanegenic digestion. Good treatment effect and high biogass convertent efficiency from COD(0.39-0.48l/g·COD· d)were gotten. Some stable and high quantity(10-100times more than sewage sludge)microorganism colony were formed in the reactor. This result provided theoretical basis for anaerobic digestion of black effluent.

微生物法沥取重金属污泥中铬的研究

本文研究了两种微生物及其组合沥取、回收用微生物法治理电镀铬废水产生的铬污泥中的铬。铬污泥富含C、N、O，含铬量为13%， 经X-光电子能谱分析铬以三价态(氢氧化铬)存在。二种微生物分别从一酸性矿水和酸性污泥中分离筛选得到，经鉴定为硫杆菌属 (Thiobacillus Beijerinek)的两个不同种，一为氧化亚铁硫杆菌(Thiobacillu ferrooxidans, TF), 另一为氧化硫硫杆菌 (Thiobacillus thiooxidans, TT)。研究并比较了不同微生物对污泥中铬的沥取能力，结果表明，TT菌沥取铬效率最高。振荡、动 态淋滤、静置等沥取方式经过研究表明动态淋滤为最佳，室温条件下(15-20℃)，污泥浓度为20g/L时，总铬沥出率达60%时所需时 间：动态淋滤为48.5h，振荡和静置方式分别为91.22，81.6h。研究了不同温度、不同起始PH、不同污泥浓度及非成熟菌液对微生 物沥取能力的影响：(1) 沥取前期，温度对铬的沥出影响较大；微生物沥取反应基本属一级反应；温度与反应速率的关系基本符合 Arrhenius方程，但沥取后期这一特点并不突出。(2) 沥取液最适起始PH为菌液自然PH；PH值的人为改变将使铬的沥出大大降低。 (3) 污泥浓度与铬的沥出呈正相关，但浓度高于30g/L时，铬的沥出量不再增加。(4) 非成熟菌液沥出铬的能力较差，但沥取液中 微生物生长繁殖较为活跃。总结微生物沥取反应最佳沥取条件为：TT成熟菌液、污泥浓度10g/L、温度25-36℃、动态淋滤方式，此 时铬几乎可100%从污泥中沥出。经扫描电镜分析，沥取开始时，微生物紧密吸附于污泥颗粒表面上，表面紧密吸附为微生物发挥功 能提供了基础。微生物沥取污泥中铬的反应机理推测为：硫细菌代谢产硫酸或氧化Fe2+成Fe3+，利用酸，Fe3+ 及自身氧化酶系统 氧化污泥中Cr3+为Cr6+,Cr6+溶出结晶为CrO3。This paper has studied bioleaching and recovery of Chronium(Cr)from electroplating sludge by two consortum of bacteria and their combination, with sludge produced by microbiological process treating electroplating wastewater containing Cr as material. The share of Cr is 13% and its state is Cr (OH)3 in the sludge. One of the bacteria in the paper was isolated from acid sewage sludge and the other was from acid mineral water. The former was tested and determined as Thiobacillus ferroxidans(TF) and the latter was Thiobacillus thiooxidans(TT). Different microorganisms, responsible for the metal leaching activity, have great influence on the efficiency of leaching. The results showed that TT has biggest power. Experiments were conducted to examined effects of three different ways of leaching(Shaking, Down-leaching, Static-leaching). When temperature was in-door's (15-20℃)and concentration of the sludge was 20g/L, the bioleaching time required to reach 60% of Cr solubilization with the above three ways were 91.2, 48.5, 81.6h respectively. Down-leaching was proved to be the most efficient. The influence of different temperature, initial PH, concentration of the sludge and non-mature inoculum had been studied. The results obtained reveal that: (1) The variation of temperature is important during the time from initial to middle of leaching. The reaction of bioleaching belongs to first-order. The relation between the bioleaching rate constant(In k)and temerature can be expressed by Arrhenius function. (2) The fittest initial PH is the nature PH of mature inoculum. Any alteration with it could cause clearly negative effection. (3) The concentration of the sludge can make strong influence on the bioleaching efficiency. But when the concentration is above 30g/L, the increasing of Cr in the solution is little. (4) If non-mature inoculum acts as the bioleachin microorganism, little quantity of Cr would be gained from the sludge. But the micormass in the solution is very active. The results from electron microscope showed that microorganisms adhered to the surface of the sludge and the adherence was the first stage of the bioleaching. Some salts of Cr can be obtained afer the water of the bioleaching solution being evaporated. By analysing the results of experiment with X-Ray spectroscopy, the salt was identified as CrO3. The recovery rate of Cr is 78.4%.

制革废水生物强化处理及中水回用试验研究

制革行业是轻工行业中仅次于造纸业的高耗水、重污染行业，作为劳动密集型行业，在解决大量人口就业问题的同时，也对所在地区环境造成了严重污染。目前我国制革行业每年排放废水8,000~12,000万吨，废水中含铬约3,500 t，SS为1.2×105 t，COD为1.8×105 t，BOD为7×104 t，对水体污染严重。 本研究在对厌氧酸化工艺进行研究、一级好氧处理段进行工艺比选研究的基础上，获得了匀质调节—SBBR—BAF的生物处理工艺，并依托该工艺进行了生物强化处理的研究，考察了菌剂的强化运行效果及其处理水回用的可行性。 研究表明，在进水COD＞3,000 mg/L，厌氧酸化具有很好的抗冲击作用，保证了好氧工艺出水COD＜200 mg/L；在进水COD＜3,000 mg/L，可只通过好氧处理实现出水COD＜200 mg/L。厌氧酸化停留时间选择不当，会导致厌氧出水硫化物浓度升高，严重影响好氧系统，会使好氧活性污泥因中毒而解絮。 研究表明，当进水COD为2,000~2,500 mg/L，NH4+-N为130~146 mg/L时，COD、NH4+-N去除率SBBR分别为93.8%~96.6%和14.5%~55.9%，SBR分别为88.8%~94.9%和13%~50.7%，表明SBBR优于SBR。同时，研究发现SBBR污泥增长率为0.05 kgVSS/kgCOD，仅为SBR0.57 kgVSS/kgCOD的8.8%。此外，研究发现SBBR在停止运行后经3个运行周期可回复原油能力，而SBR池经9个周期培养也不能恢复，说明SBBR恢复能力明显优于SBR。 研究表明，以匀质调节—SBBR—BAF为主的制革废水处理工艺，出水水质稳定，进水COD 801~2,834 mg/L、NH4+-N 87~203 mg/L，出水COD＜80 mg/L、NH4+-N＜10 mg/L，基本达到中水回用标准；操作简单灵活，没有污泥回流系统，污泥产率低，污泥处理费用低；工艺基本不需要添加化学药剂，既节约成本、又避免了二次污染；两级生物膜使得该工艺具有很强的耐冲击负荷能力，特别适合制革废水水质水量波动大的特点。 研究表明，高效菌对系统的启动具有一定的促进作用，强化系统生物膜6天可以成熟，对照系统生物膜9天可以成熟。同时高效菌能加速COD降解，缩短停留时间，强化系统6~8 h可使COD＜200 mg/L，对照系统8~10 h可使COD＜200 mg/L。长期运行表明，强化系统的SBBR在COD和NH4+-N的去除率都优于对照系统的SBBR。最终出水COD强化系统平均为53 mg/L、对照系统为74 mg/L。在模拟循环过程中，强化系统均有更高的稳定性。可实现8次理论循环，而对照系统只能实现4次理论循环。 研究表明，通过合理的工艺设计，可以实现猪皮制革废水达到《污水综合排放标准GB8976-1996》一级标准，同时满足工厂部分用水要求。通过添加高效微生物，可提高生物处理系统处理能力，使处理水能够满足工厂的多次回用。 As a labour-intensive industry, tanning has created large amount of working opportunities as well as caused severe contamination to environment. And it is one of the highest water-consuming and polluting industry, only second to manufacturing. At present time, Chinese leather industry emits wastewater about 80,000,000~120,000,000 t annually, which contains chromium about 3,500 t, SS 1.2×105 t, COD 1.8×105 t, BOD 7×104 t and ambient riverhead has been polluted greatly. Based on the research of anaerobic acidification and comparison of SBBR and SBR, biotreatment process (Homogenization—SBBR—BAF) had been established to amend the disadvantages of traditional sewage treatment such as too much sludge, high cost of advanced treatment and NH4+-N can not reach the emission standard. Research on the bioaugmentation was also been carried out. Researches showed, when COD of influent was beyond 3,000 mg/L, anaerobic acidification could resist strong impact, thus COD of effluent was less than 200 mg/L; when COD of influent was less than 3,000 mg/L, only throughout aerobic sewage treatment could COD of effluent beless than 200 mg/L. False residence tiome of anaerobic acidification would lead to the higher effluent concentration of sulfide and disintegration of aerobic activated sludge. Researches showed SBBR worked a better than SBR: when influent between 2,000 and 2,500 mg/L, NH4+-N between 130 mg/L and 146 mg/L, COD, NH4+-N removal rate of SBBR was 93.3%~96.6%, 14.5%~55.9% respectively while COD, NH4+-N removal rate of SBR was 88.8%~94.9%, 13%~50.7% respectively. Sludge growth rate of SBBR was 8.8% of that of 0.05 kgVSS/kgCOD. Besides, SBBR could recovered after 3 operating periods while SBR worked no better after 9 operating periods.Therefore, SBBR excelled SBR. Researches showed, effluent quantity of tannery wastewater treatment process (Homogenization—SBBR—BAF) was stable. When COD of influent was between 801 and 2,834 mg/L, NH4+-N was between 87 mg/L and 203 mg/L, COD of effluent was less than 80 mg/L, NH4+-N was less than 10 mg/L, which achieved the standard of reuse. This biotreatment was featured in low cost, easy and flexible management, less sludge, no inverse sludge system. Besides, this technique required no chemical, which could lower the cost and avoid secondary pollution. Great resistant of impact due to two membranes and was suitable for tannery wastewater which was featured by fluctuation of influent quality and quantity. Researches showed effective microorganisms promotes the startup of the process.Biofilm in the bioaugmentation process matured with 6 days while biofilm in normal process matured with 9 days. Effective microorganisms could accelerate the degradation of COD and shorten the residence time. Aggrandizement system could make COD<200 mg/L with 6 to8 hours while cntrolling system could make COD<200 mg/L with 8 to 10 hours. Long-term operating shows that SBBR in the bioaugmentation system worked better than the normal system in the treatment of COD and NH4+-N. The average COC of effluent in bioaugmentation system was 53 mg/L, normal system was 74 mg/L. In the simulative circulation process,aggrandizement process, which could fulfill 8 times theoretical circulation, works more stably than controlling process which could only fulfill 4 times theoretical circulation. Researches showed that reasonable design could make the wastewater meet the first grade of discharging standard of National Integrated Wastewater Discharge Standard (GB8976-1996), and partially meet the demand of water using of the factory. Adding effective microorganisms could enhance the biotreatment and make the effluents reuse many times.

Concentrations of alkyphenol polyethoxylates entering UK estuaries

Concentrations of the weakly oestrogenic degradation products of alkylphenol polyethoxylate (APE) surfactants (nonylphenol, octylphenol, nonylphenol monoethoxylate and nonylphenol diethoxylate) were measured in water and sediments from British rivers and estuaries collected during 1994 and 1995. In addition, a series of samples of tissues of wild fish from the River Aire, and from a laboratory dosing experiment were analysed for alkylphenols, to assess the degree of bioaccumulation of these compounds. Measurable concentrations of APE residues were recorded in the River Aire (15–76 μg/l total extractable alkylphenols), the River Mersey (6–11 μg/l) and the Tees estuary (up to 76 μg/l). These levels exceed, or are close to, the no observed effect concentration for the induction of vitellogenesis in caged trout (5–20 μg/l total extractable alkylphenols), and may be sufficient to exert an oestrogenic effect on fish populations in these areas. A sediment sample from Bingley on the River Aire contained 15 μg/g (dry weight) nonylphenol, and concentrations in sediments from the Tees and Mersey estuaries exceeded 1 μg/g. These rivers receive a variety of trade waters via sewage treatment works (STW) effluents containing significant concentrations of APE. Elsewhere, concentrations in water and sediments were near or below limits of detection and biological effects are unlikely, suggesting that any oestrogenic effects observed in sewage outfalls and rivers not directly impacted by APE-containing trade-waters may be caused by other chemicals. Analysis of samples of trout muscle taken from a tank dosed at 65 μg/l nonylphenol indicated a bioaccumulation factor of between 90 and 125 after 3 weeks exposure. Samples of wild fish from the River Aire contained up to 0.8 μg/g nonylphenol in the muscle, a tissue bioaccumulation factor of approximately 50 relative to measured concentrations in water samples. A series of fish samples taken from offshore for food quality assurance purposes contained no detectable levels of APE residues (0.05–0.1 μg/g nonylphenol).

Dinoflagellate Cysts as Indicators of Cultural Eutrophication in the Oslofjord, Norway

Dinoflagellate cyst records were analysed from four sediment cores from the inner Oslofjord. The cores covered the pre-industrial period, and the most important period of human population growth associated with industrial development of the region, from the mid-1800s to the present, including the reported development of cultural eutrophication. Comparisons between the cyst records and the known history of eutrophication suggest cyst signals that should prove useful for tracing the development of eutrophication. The eutrophication signal consisted of a doubling of total cyst concentration, and a marked increase in one species in particular,Lingulodinium machaerophorum(from <5 to around 50% of the assemblages) with increased eutrophication. In the core considered most representative of general water quality in the inner fjord, these trends reversed back to pre-industrial levels during the 1980s and 1990s when improved sewage treatment took effect.

Model analysis of dissolved inorganic phosphorus exports from the Yangtze river to the estuary

In this paper, we estimate the inputs of phosphorus (P) to the Yangtze River Basin and exports of dissolved inorganic phosphorus (DIP) from the river to the estuary for the period 1970-2003, by using the global NEWS-DIP model. Modeled DIP yields range from 2.5 kg P km(-2) yr(-1) in 1970 to 4.6 kg P km(-2) yr(-1) in 1985, and then dramatically increase to 14.1 kg P km(-2) yr(-1) in 2003. No significant difference between the modeled and measured values at the level of P = 0.05 is observed. The study also demonstrates variable source contributions of P to the modeled DIP during the period 1970-2003. Point sewage P input accounted for approximately 100% in the period 1970-1985 and substantially decreased to 24.8% in 2003. Chemical fertilizer contributed 25.4% of DIP yields in 1986 and increased continuously to 50.3% in 2003, while a stable trend in manure P contribution averaging 22.9% of DIP yields was shown in the same period. The study concludes that P inputs to the Yangtze River Basin and the river DIP export to the estuary have substantially increased during the study period consequence to human pressure.

Evaluation of a sequential extraction for the speciation of thorium in soils from Baotou area, Inner Mongolia

Sequential extraction procedures were widely applied for speciation of radioactive elements. In this study, the sequential extraction procedure developed by Martinez-Aguirre was employed for quantification of different chemical forms of thorium in the soil. The total amount of thorium in contaminated soil was much higher by four-fold than the local background value. The soil properties affect the amount of thoriurn and distribution of fractions in contaminated soil. Results showed that the proportion of thorium in soils from Baotou was found as the residual fraction (F5 + F6) > absorbed fraction (F3), coprecipitated fraction (F4) > carbonates fraction (172) and exchangeable fraction (F1) that could be available to plants. The recovery, calculated by ratio of the sum of the six fractions to the pseudo-total content of thorium, was in the range from 96% to 110%. A comparison was carried out between the sequential extraction and the single extraction to evaluate the selectivity of the extractants. It was found that the amount of thorium of absorbed fraction (H) was higher in the single extraction than that estimated in the sequential extraction, possibly duo to transform of the labile form. While for non-residual fraction analysis, the single extraction scheme was a desirable alternative to the sequential extraction procedure.

Dominant chloramphenicol-resistant bacteria and resistance genes in coastal marine waters of Jiaozhou Bay, China

Studies of abundance, diversity and distribution of antibiotic-resistant bacteria and their resistance determinants are necessary for effective prevention and control of antibiotic resistance and its dissemination, critically important for public health and environment management. In order to gain an understanding of the persistence of resistance in the absence of a specific antibiotic selective pressure, microbiological surveys were carried out to investigate chloramphenicol-resistant bacteria and the chloramphenicol acetyltransferase resistance genes in Jiaozhou Bay after chloramphenicol was banned since 1999 in China. About 0.15-6.70% cultivable bacteria were chloramphenicol resistant, and the highest abundances occurred mainly in the areas near river mouths or sewage processing plants. For the dominant resistant isolates, 14 genera and 25 species were identified, mostly being indigenous estuarine or marine bacteria. Antibiotic-resistant potential human or marine animal pathogens, such as Escherichia coli, Klebsiella pneumoniae, Proteus mirabilis and Shewanella algae, were also identified. For the molecular resistance determinants, the cat I and cat III genes could be detected in some of the resistant strains, and they might have the same origins as those from clinical strains as determined via gene sequence analysis. Further investigation about the biological, environmental and anthropogenic mechanisms and their interactions that may contribute to the persistence of antibiotic-resistance in coastal marine waters in the absence of specific antibiotic selective pressure is necessary for tackling this complicated environmental issue.

Incidence of diverse integrons and beta-lactamase genes in environmental Enterobacteriaceae isolates from Jiaozhou Bay, China

Environmental microbiology investigation was performed to determine the molecular diversity of beta-lactamase genes among ampicillin-resistant bacteria from Jiaozhou Bay. beta-lactamase genes were detected in 93.8% of the bacterial isolates identified as Enterobacteriaceae. The most frequently detected gene was bla(TEM), followed by bla(SHV), bla(OAX-1), bla(MOX) and bla(CMY). Most of the isolates (68.8%) were positive for the intI1 integrase gene, and two isolates were also found for the intI2 gene. The dfr and aadA gene cassettes were predominant. Anthropogenic contamination from onshore sewage processing plants might contribute predominantly to the beta-lactamase gene reservoir in the studied coastal waters. Environmental antibiotic-resistant bacteria and resistance genes may serve as bioindicators of coastal environmental quality or biotracers of the potential contamination sources. This is the first report of the prevalence and characterization of beta-lactamase genes and integrons in coastal Enterobacteriaceae from China.

Persistent organic pollutant residues in the sediments and mollusks from the Bohai Sea coastal areas, North China: An overview

The Bohai Sea costal area is one of the most developed zones of China and the sewage water from populous and developed cities, including Beijing, Tianjin. Qinhuangdao and Dalian is discharged into the Bohai Sea. Additionally, its semi-enclosed characteristic restricts water exchange, which leads to high accumulation of pollutants in the environment. This overview presents the residues of 6 classes of Persistent Organic Pollutants (POPs). including PAHs, DDTs. HCHs, PCBs and PCDD/Fs. in the sediments and mollusks of the Bohai Sea through analyzing previous literatures. In the sediments. the highest PAH concentrations were detected in the vicinities of Qinhuangdao, while the northeast corner of the Bohai Bay possessed the highest levels of DDTs and PCBs. The investigations on HCHs and PCDD/Fs distributions on the whole sea scale have not been reported. In mollusks, PAH concentrations were in the same order of magnitude in the whole Bohai Sea, so were DDTs. HCHs and PCBs, while the outlier maximum values of PCDDs and PCDFs occurred in Yingkou. In general, the POPs residues in mollusks collected from Shandong Province were higher than the other areas. The compositions of DDTs, HCHs and PCBs in sediments indicated their recent usage. By comparing POP concentrations in sediments with the recommended criterions, it was shown that some individual PAH compounds occasionally associated with adverse biological effects in the vicinities of the Liaodong Bay and Qinhuangdao, and the Liaohe River Estuary were heavily contaminated with DDTs, but PCBs were all below the thresholds. In order to reveal the transference and transformation of POPs in the environment, further studies concerning with their behavior, fate and bioaccumulation in the different trophic levels should be programmed. Moreover, laws and regulations should be enforced to ban the illegal usage of POPs-containing pesticides to guarantee health of the environment and human. (C) 2008 Elsevier Ltd. All rights reserved.

Stable carbon and nitrogen isotopic compositions of high molecular weight dissolved organic matter from four US estuaries

High molecular weight dissolved organic matter (HMW-DOM) represents an important component of dissolved organic carbon (DOC) in seawater and fresh-waters. In this paper, we report measurements of stable carbon (delta(13)C) isotopic compositions in total lipid, total hydrolyzable amino acid (THAA), total carbohydrate (TCHO) and acid-insoluble "uncharacterized" organic fractions separated from fourteen HMW-DOM samples collected from four U.S. estuaries. In addition, C/N ratio, delta(13) C and stable nitrogen (delta(15)N) isotopic compositions were also measured for the bulk HMW-DOM samples. Our results indicate that TCHO and THAA are the dominant organic compound classes, contributing 33-46% and 13-20% of the organic carbon in HMW-DOM while total lipid accounts for only <2% of the organic carbon in the samples. In all samples. a significant fraction (35-49%) of HMW-DOM was included in the acid-insoluble fraction. Distinct differences in isotopic compositions exist among bulk samples, the compound classes and the acid-insoluble fractions. Values of delta(13)C and delta(15)N measured for bulk HMW-DOM varied from -22.1 to -30.1parts per thousand and 2.8 to 8.9parts per thousand, respectively and varied among the four estuaries studied as well. Among the Compound classes, TCHO was more enriched in C-13 (delta(13)C = -18.5 to -22.8parts per thousand) compared with THAA (delta(13)C = -20.0 to -29.6parts per thousand) and total lipid (delta(13)C = -25.7 to -30.7parts per thousand). The acid-insoluble organic fractions, in general, had depleted C-13 values (delta(13)C = -23.0 to -34.4parts per thousand). Our results indicate that the observed differences in both delta(13)C and delta(15)N were mainly due to the differences in sources of organic matter and nitrogen inputs to these estuaries in addition to the microbial processes responsible for isotopic fractionation among the compound classes. Both terrestrial sources and local sewage inputs contribute significantly to the HMW-DOM pool in the estuaries studied and thus had a strong influence on its isotopic signatures. Copyright (C) 2004 Elsevier Ltd.

Phosphine in various matrixes

Matrix-bound phosphine was determined in the Jiaozhou Bay coastal sediment, in prawn-pond bottom soil, in the eutrophic lake Wulonglan, in the sewage sludge and in paddy soil as well. Results showed that matrix-bound phosphine levels in freshwater and coastal sediment, as well as in sewage sludge, are significantly higher than that in paddy soil. The correlation between matrix bound phosphine concentrations and organic phosphorus contents in sediment samples is discussed.