掺镱双包层光纤放大器高功率脉冲放大特性

从放大器速率方程出发，分析了掺镱双包层光纤放大器的放大特性。模拟计算了无信号输入时放大器上能级粒子数、泵浦功率和放大自发辐射（ASE）在放大器中的稳态分布。分析了前向和后向泵浦时，高功率高斯脉冲放大时的脉冲波形畸变、上能级粒子数的时间特性、放大器存储能量和脉冲能量演化等动态特性。讨论了掺镱双包层光纤放大器输出脉冲能量随不同输入脉冲峰值功率和泵浦功率的关系。该模型和结论对高功率脉冲放大器的设计和优化具有一定的理论指导意义。

基于高频微波技术的分布式光纤传感器布里渊散射信号检测

分析了布里渊分布式光纤传感技术原理,采用自行研制的光纤单纵模分布反馈(DFB)激光器结合电光调制技术,利用相干检测技术,对布里渊微弱后向散射信号进行检测。通过改进滤波放大技术,对微弱后向散射光信号进行有效放大,再用扰偏技术及信号采样平均处理,实现对光纤传感器后向布里渊散射信号在11 GHz高频段直接采集显示。结果表明,探测所得布里渊散射信号峰值功率可达50 mV,能有效降低解调系统信号检测难度,改善了系统信噪比(SNR)。初步实验结果证明了该方案的可行性。

掺镱双包层光纤放大器的放大特性

从掺镱(Yb)光纤放大器的功率传输方程出发,利用有限差分法对小模场面积(SMA)和大模场面积(LMA)掺镱双包层光纤放大器的放大特性进行了分析比较。采用模场直径(MFD)6.5 μm和20 μm的双包层掺镱光纤作为放大器增益介质进行窄线宽连续信号的放大,在915 nm激光抽运下模拟计算了大、小模场面积输出功率随输入信号功率、抽运光功率和光纤长度的变化特性,特别是对于大模场面积光纤放大器,最优光纤长度的选择至关重要;讨论了模场直径不同时的最优抽运功率和光纤长度的选择,得出4 m光纤放大时的临界抽运功率为4

高重复频率、窄脉宽全固态光纤放大器种子源

高重复频率、窄脉宽的全固态激光器种子源级联光纤放大器是获得高功率脉冲激光输出的有效手段.短上能态寿命的Nd∶YVO4晶体在连续抽运、高重复频率Q开关工作时容易得到接近连续性能的平均输出功率.理论分析了声光(AO)调Q器件中影响输出能量和脉宽大小的主要因素,优化配置了腔型参数.利用激光二极管(LD)光纤耦合模块端面抽运Nd∶YVO4晶体,实现了声-光调Q重复频率100 kHz以上,脉宽20 ns以下,波长1064 nm的激光输出.在抽运功率5.7 W时,得到了脉宽15.3 ns,重复频率150 kHz的种子光输出,在级联单级光纤放大器后,得到了20 W的输出.

PPLT倍频宽线宽掺镱双包层光纤放大激光

分别通过理论和实验研究了周期性极化的钽酸锂（PPLT）倍频宽线宽准连续掺镱双包层光纤放大激光．PPLT样品长为40mm，极化周期为7．67μm．基频光的中心波长为1064nm，线宽约为6nm。从基频光的光谱特性出发，利用超晶格倍频理论，解释了实验中获得的倍频温度与二次谐波功率之间的关系．在基频光的功率为2．2W时，获得的宽线宽光纤激光倍频效率为1．8％。

双程掺镱光纤放大器的增益特征及优化

比较了掺钕光纤和掺镱光纤对1064nm光放大的特点．基于速率方程和传输方程，数值分析了在915nm泵浦下双程掺镱光纤放大器的增益特征，并且和传统的单程放大进行了比较．分析了信号光和泵浦光，以及粒子数沿着光纤方向的分布特点．最后对双程掺镱光纤放大器进行了优化．

氟磷酸盐玻璃的应用研究进展

氟磷酸盐玻璃系统南于其特殊的光学性能和优良的机做与热学性能一直是特种光学玻璃材料领域的一个研究热点。总结了氟磷酸盐玻璃的分类及玻璃组分与其结构的关系，综述了氟磷玻璃在光学器件、高能高功率激光玻璃、光纤激光器、光纤放大器及上转换发光基质材料等领域上的应用，并对其未来的发展进行了展望。

新型掺铒离子氧氟碲酸盐玻璃的光谱性质

探求新的具有优良的热学和光学性能的基质玻璃系统，是获得具有宽带宽和增益平坦的掺Er^3＋光纤放大器（EDFA）的一种有效途径。制备了一种新型氧氟碲酸盐玻璃TeO2-BaF2-LaF3，并对其热学性能和光学性质进行了测试。应用乍得-奥菲尔特（Judd-Ofelt）理论计算了Er^3＋离子的J-O理论参量和荧光寿命r。探讨了氟化物的引入对碲酸盐玻璃结构的改变的影响，并分析了其对玻璃的热学性质和光学性质的影响。实验发现，获得的氧氟碲酸盐玻璃具有优良的热学稳定性（△T=156.6C），宽的荧光半峰全宽（72nm）

Infrared-to-visible upconversion emissions in Er3+ doped TeO2-based oxyhalide glasses

The fluorescence and up-conversion spectral properties of Er3+-doped TeO2-ZnO and TeO2-ZnO-PbCl2 glasses suitable for developing optical fiber amplifier and laser have been fabricate and characterized. Strong green (around 527-550 nm) and red (around 661 nm) up-conversion emissions under 977 nm laser diode excitation were investigated, corresponding to H-2(11/2), S-4(3/2), --> I-4(15/2) and F-4(9/2) --> I-4(15/2) transitions of Er3+ ions respectively, have been observed and the involved mechanisms have been explained. The dependence of up-converted fluorescence intensity versus laser power confirm that two-photons contribute to up-conversion of the green-red emissions. The novelty of this kind of optical material has been its ability in resisting devitrification, and its promising optical properties strongly encourage for their further development as the rare-earth doped optical fiber amplifiers and upconversion fiber laser systems.

掺铒碲酸盐玻璃的热力学稳定性和光谱性质的研究

分析了掺Er^3+碲酸盐玻璃的热力学稳定性能，研究了掺Er^3+碲酸盐玻璃的吸收和荧光光谱性质；应用Judd-Ofelt理论计算了碲酸盐玻璃中Er^3+离子的强度参数Ω(Ω2=4．79×10^-20cm^2,Ω4=1．52×10^-20cm^2，Ω6=0．66×10^-20cm^2)，计算了离子的自发跃迁几率，荧光分支比；应用McCumber理论计算了Er^3+的受激发射截面(σe=10．40×10^-21cm^2)、Er^3+离子^4I13／2→^4I15／2发射谱的荧光半高宽(FWHM=65．5nm)

Stability against crystallization and spectroscopic properties of Tm3+ doped fluorophosphate glasses

Fluorophosphate glasses with various content of Al(PO3)(3) were prepared. With the increment of Al(PO3)(3) content, density decreases while refractive index increases, and transition temperature, crystallization peak temperature and melt temperature increase which were suggested by differential scanning calorimetry. These glasses exhibit the best stability against crystallization with 7-9 mol'Yo Al(PO3)(3) content. Normalized Raman spectra were used to analyze structure and phonon state. The increment of Al(PO3)(3) content does not affect phonon energy but results in the augment of phonon density. Absorption spectra were measured. H-3(6) -> F-3(4) transition exhibits absorption at L band of the third communication window. Compared with the energy of Tm3+ excited states in other glass system, F-3(4) energy of Tm3+ in these glasses is considerable higher and H-3(4) energy is considerable lower, and it can be predicted that emission band of H-3(4) -> F-3(4) transition is close to the amplified band of gain-shift Tm3+ doped fiber amplifier. Analyses of Judd-Ofelt theory suggest when Al(PO3)(3) content is no more than 7 mol%, Judd-Ofelt parameters Omega(t) and the lifetime of H-3(4) energy level of TM3+ vary little with the increment of Al(PO3)(3) content, and when Al(PO3)(3) content is more than 7 mol%, Omega(2) and Omega(6) increase and radiative lifetime of H-3(4) energy level of Tm3+ drops sharply with the increment of Al(PO3)(3) content. (c) 2006 Elsevier B.V. All rights reserved.

稀土离子掺杂的多组分玻璃光纤

abstract {Rare earth ions doped multi-component glass fibers have important application in broad band fiber amplifier and up-conversion fiber lasers. In this paper, the mechanism and the progress of study on rare earth ions doped multi-component glass fibers in broad band fiber amplifier and up-conversion fiber lasers are introduced and reviewed. The questions and the applications of rare earth ions doped multi-component glass fibers in the future are also prospected. Based on the present research progress, it is suggested to further study the tellurite and bismuth glasses, which are used as fiber materials in broad band fiber amplifier. To up-conversion fiber laser, it is still need to further investigate novel glasses, which has low phonon energy and good physical and chemical properties.}

Spectroscopic properties of Er3+ doped TeO2-BaO (Li2O, Na2O)-La2O3 glasses for 1.5-mu m optical amplifiers

This paper reports on the optical spectroscopic properties and thermal stability of Er3+-doped TeO2-BaO (Li2O,NaO)-La2O3 glasses for developing 1.5-mu m fiber amplifiers. Upon excitation at 977 nm laser diode, an intense 1.53-mu m infrared fluorescence has been observed with a broad full width at half maximum (FWHM) of about 60 nm for the Er3+-doped TeO2-BaO (Li2O, Na2O)-La2O3 glass with 10 mol% of BaO. The calculated fluorescence lifetime and the emission cross-sections of the 1.53-mu m transition are 2.91 ms and similar to 9.97 x 10(-21) cm(2), respectively. It is noted that the gain bandwidth, a, x FWHM, of the TeO2-BaO-La2O3Er2O3 glass is about 600, which is significantly higher than that in silicate and phosphate glasses. Meanwhile, it is interesting to note that the TeO2-BaO-La2O3-Er2O3 glass has shown a high glass thermal stability and good infrared transmittance. As a result, TeO2-BaO (Li2O, Na2O)-La2O3 glass with 10 mol% of BaO has been considered to be more useful as a host for broadband optical fiber amplifier. (c) 2005 Elsevier B.V. All rights reserved.

Preparation and spectroscopic properties of Er3+-doped high silica glass fabricated by sintering nanoporous glass

A compact nonporous high silica (SiO2 % > 96%) glass containing 3400 ppm Er3+ ions, which was about ten times higher than that in Er-doped silica fiber amplifier (EDSFA), was synthesized by sintering porous glass immersed into erbium nitrate solution. The 1532 nm fluorescence has a FWHM (Full Width at Half Maximum) of 45 nm wider than that of EDSFA and possesses the glass with potential application in broadband fiber amplifiers. The Judd-Ofelt theoretical analysis reflects that Er3+ ions are located in a higher covalent environment which are comparable to those of aluminosilicate glass. (c) 2005 Elsevier B.V. All rights reserved.

Theoretical investigation on quantum well lasers with extremely low vertical beam divergence and low threshold current

A specially designed quantum well laser for achieving extremely low vertical beam divergence was reported and theoretically investigated. The laser structure was characterized by two low index layers inserted between the waveguide layers and the cladding layers. The additional layers were intended to achieve wide optical spread in the cladding layers and strong confinement in the active region. This enabled significant reduction of beam divergence with no sacrifice in threshold current density. The numerical results showed that lasers with extremely low vertical beam divergence from 20 degrees down to 11 degrees and threshold current density of less than 131 A/cm(2) can be easily achieved by optimization of the structure parameters. Influences of individual key structure parameters on beam divergence and threshold current density are analyzed. Attention is also paid to the minimum cladding layer thicknesses needed to maintain low threshold current densities and low internal loss. The near and far field patterns are given and discussed. (C) 1998 American Institute of Physics.