36 resultados para post-structuralism
Raman scattering study on Ga1-xMnxAs prepared by Mn ions implantation, deposition and post-annealing
Resumo:
Raman scattering measurements have been performed in Ga1-xMnxAs crystals prepared by Mn ions implantation, deposition, and post-annealing. The Raman spectrum measured from the implanted surface of the sample shows some weak phonon modes in addition to GaAs-like phonon modes, where the GaAs-like LO and TO phonons are found to be shifted by approximately 4 and 2 cm(-1), respectively, in the lower frequency direction compared to those observed from the unimplanted surface of the sample. The weak vibrational modes observed are assigned to hausmannite Mn3O4 like. The coupled LO-phonon plasmon mode (CLOPM), and defects and As related vibrational modes caused by Mn ions implantation, deposition, and post-annealing are also observed. The compositional dependence of GaAs-like LO phonon frequency is developed for strained and unstrained conditions and then using the observed LOGaAs peak, the Mn composition is evaluated to be 0.034. Furthermore, by analyzing the intensity of CLOPM and unscreened LOGaAs phonon mode, the hole density is evaluated to be 1.84 x 10(18) cm(-3). (C) 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim
Resumo:
Rapid thermal annealing (RTA) has been demonstrated as an important way to improve the crystal quality of GaInNAs(Sb)/GaAs quantum wells. However little investigation has been made into their application in laser growth, especially at a wavelength of 1.55 mu m. When a GaAs-based laser is grown, AlGaAs is usually used for cladding layers. The growth of the p-cladding layer usually takes 30-45 min at a growth temperature higher than that of the GaInNAs(Sb) active region, which affects the material quality. To investigate this effect, various post-growth annealing processes were performed to simulate this process. Great enhancement of the PL intensity was obtained by a two-step process which consisted of annealing first at 700 degrees C for 60 s and then at 600 degrees C for 45 min. We transferred this post-growth annealing to in situ annealing. Finally, a GaInNAsSb laser was grown with a 700 degrees C in situ annealing process. Continuous operation at room temperature of a GaAs-based dilute nitride laser with a wavelength beyond 1.55 mu m was realized for the first time.
Resumo:
提出了一种在Post-WIMP环境下的笔式交互范式:PIBG.PIBG范式采用纸笔隐喻,与WIMP范式相比,承载应用信息的交互组件由Window变为Paper和Frame,用户的交互动作由鼠标的点击变为笔的手势.对PIBG范式中静态的界面形式和动态的交互手势进行了研究和设计.结合认知心理学,从信息呈现和交互方式两个方面对该范式的特点进行了阐述.利用GOMS模型,从界面呈现方式、手势的效率、用户满意度三个方面对该范式进行了心理学评估.从评估结果可以看,PIBG范式通过模拟日常纸笔环境,利用用户原有的知识,可以明显地减轻认知负担,提高操作效率.
Resumo:
首先从认知心理学的角度对Post—WIMP界面下的隐式交互特征进行分析和描述。然后通过对传统界面的交互任务生成结构和Post—WIMP界面的交互任务生成结构进行比较,分析Post—WIMP界面交互任务的生成特点。根据这些特点提出了利用识别技术、上下文感知技术和用户修正技术(User Mediation)相结合的方法来支持Post—WIMP界面的隐式交互,并构造了Post—WIMP界面的交互任务生成框架。这些隐式交互特征的研究将为建立Post—WIMP界面软件框架和交互平台提供底层支持。
Resumo:
Post- WIMP界面作为继当前的主流界面范式—— WIMP界面后的下一代界面范式 ,它和 WIMP界面有着很大的不同 ,通过使用虚拟现实、语音交互、手势交互等技术 ,它能够提供更加自然高效的交互方式 .然而 ,它却难以构造 .为了有效地构造 Post- WIMP界面 ,在构造之前不考虑实现细节 ,而在一个抽象的层次上描述它是一个较好的方法 .首先 ,分析了 Post- WIMP界面的交互本质 ,交互混合性是 Post- WIMP界面一个最为重要的特点 .从形式化系统的角度分析 Post- WIMP界面 ,通过将 Post- WIMP界面抽象为混合系统能够更为准确和严格地分析Post- WIMP界面的特性 .混合自动机是用于描述混合系统的形式化工具 ,将 Post- WIMP界面建模为一组相互协作的混合自动机 .设计了一基于混合自动机理论的半形式化语言 L EAFF作为 Post- WIMP界面的描述工具 .LEAFF通过结合文本描述和图形描述描述 Post- WIMP界面中的交互行为 ,能够准确地反映交互中的控制关系、时序关系 .给出了对两个典型 Post- WIMP界面——虚拟现实交互和笔式交互的描述实例 ,同时讨论了 Post- WIMP界面中交互并行性的描述、交互实时性的验证和从描述到实际交互系统构造的转换 .
Resumo:
Post-steam-treatment is a facile and effective method for improving the catalytic performances of Mo/HZSM-5 catalysts in methane dehydroaromatization under nonoxidative conditions. The treatment can enhance the stability of the catalyst and also give a higher methane conversion and a higher yield of light aromatics, as well as a decrease in the formation rate of carbonaceous deposits. (27)Al, (29)Si, and (1)H multinuclear magic angle spinning nuclear magnetic resonance, X-ray photoelectron spectroscopy, X-ray diffraction, X-ray fluorescence spectroscopy, and thermogravimetric analysis measurements as well as catalytic reaction evaluations were employed to conduct comparative studies on the properties of the catalysts before and after the post-steam-treatment. The results revealed that the number of free Bronsted acid sites per unit cell decreased, while more Mo species migrated into the HZSM-5 channels for the 6Mo/HZSM-5 catalysts after the post-steam-treatment. In addition, the average pore diameter was also larger for the post-steam-treated catalysts, and this was advantageous for mass transport of the reaction products. However, a severe post-steam-treatment, i.e., with longer treating time, of the 6Mo/HZSM-5 catalyst will lead to the formation of the Al(2)(MoO(4))(3) phases, which is detrimental to the reaction.
Resumo:
Plant cell cultures have been suggested as a feasible technology for the production of a myriad of plant-derived metabolites. However, commercial application of plant cell culture has met limited success with only a handful of metabolites produced at the pilot- and commercial-scales. To improve the production of secondary metabolites in plant cell cultures, efforts have been devoted predominantly to the optimization of biosynthetic pathways by both process and genetic engineering approaches. Given that secondary metabolism includes-the synthesis. metabolism and catabolism of endogenous compounds by the specialized proteins, this review intends to draw attention to the manipulation and optimization of post-biosynthetic events that follow the formation of core metabolite structures in biosynthetic pathways. These post-biosynthetic events-the chemical and enzymatic modifications, transport, storage/secretion and catabolism/degradation have been largely unexplored in the past. Potential areas are identified where further research is needed to answer fundamental questions that have implications for advanced bioprocess design. Anthocyanin production by plant cell cultures is used as a case study for this discussion, as it presents a good example of compounds for which there are extensive research publications but still no commercial bioprocess. It is perceived that research on post-biosynthetic processes may lead to future opportunities for significant advances in commercial plant cell cultures. (C) 2002 Elsevier Science Inc. All rights reserved.
Resumo:
随着计算机应用从桌面环境扩展到移动环境,计算机用户从专业化走向大 众化,传统的 WIMP界面的缺点逐渐体现出来。笔式用户界面作为 Post-WIMP 界面的一种重要形式,具有自然、和谐的交互特性,成为当前研究的热点之一。 针对这一方向,本文对笔式用户界面范式展开了研究。首先,本文阐述了一种 新的基于笔交互的界面范式 PGIS,定义了纸、小工具等交互组件,以及各种组 件的显示形态及交互形式。然后,实现了 PGIS 界面,包括交互对象的管理、 显示等内容。最后,详细介绍了 PGIS 界面的使用过程,并用一个应用实例加 以验证。为了支持上层应用程序的可移植性和可维护性,PGIS界面的使用采用 了模型驱动构架的开发思想。目前,我们基于 PGIS 界面开发了几款优秀的笔 式交互软件,如幼儿教学系统、便签本系统、篮球战术板系统等。这些系统完 全满足用户对笔交互应用程序的需求,目前可在 Linux 系统、Windows 系统等 多种系统上运行。PGIS界面范式的可行性也因此得到了很好的验证。 本文的主要内容有以下几点: 1. 阐述了一种 Post-WIMP范畴下的新的界面范式:PGIS。 本文在对Post-WIMP界面做了充分地理解和分析的基础上,阐述了一种新 的界面范式:PGIS。这是一种基于笔交互的界面范式,文中对该范式的纸笔隐 喻方式、所包含的内容、各交互组件的表现形式、以及各组件间的静态及动态 关系做出了详细的描述。 2. 实现了PGIS界面。 为了验证PGIS界面范式的可行性,并直接支持基于 PGIS范式的应用程序 开发,本文详细介绍了PGIS界面的实现细节,其中包括PGIS界面中所包含的 元素、PGIS界面中交互对象的显示、交互对象的管理、以及交互对象对基本原 语的转换和响应。 3. 介绍了 PGIS界面的使用过程。 整个使用过程采用模型驱动架构的思想,引入对以下三个子模块的调用: 与平台相关的底层核心库和 PGIS 引擎、与平台无关的场景设计工具。这三个 子模块决定了上层应用程序的可移植性和可维护性。另外,场景设计工具提供 了代码自动生成的功能,大幅度缩短了应用程序的开发周期。 4. 实现了一个基于 PGIS界面的幼儿教学系统。 为了说明 PGIS界面的使用流程,本文设计并实现了一个基于PGIS界面的 幼儿教学系统。在开发过程中,大部分工作在场景设计工具中快速完成,小部 分工具集中在数据管理库、场景任务库的开发上。该系统的评估结果很好地验 证了 PGIS界面范式的可行性。
Resumo:
We investigate the effect of thermal annealing before and after cathode deposition on the stability of polymer light-emitting diodes (PLEDs) based on green fluorescent polyfluorene derivative. The annealed PLEDs exhibit improved charge transport and red-shift emission compared to the as-fabricated device. The stability of the PLEDs is largely enhanced by post-annealing before and after Ca deposition, which is attributed to the enhanced charge transport and the intimate contact between the cathode and the emissive layer.
Resumo:
The functional polystyrene, (Cl-PS)(2)-CHCOOCH2CH2OH ( designated as XPSt and coded P2) was prepared by ATRP at 130(0)C using CuCl and bipyridine as catalysts, 2,2-dichloro acetate-ethylene glycol (DCAG) as multifunctional initiator and THF as solvent. 4-Nitoroaniline azomethine-4' phenol (P1) as chromophores were covalently linked to the functional end groups of the polymer by using simple displacement reaction. The functional polystyrenes, namely XPSt (P2) and (PS)(2)-CHCOOCH2CH2OH, designated as X-PSt and coded P3 and their post-derivatives, namely, DXPSt (P4) and DX-PSt (P5) respectively were characterized by IR, NMR and UV spectroscopies, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), polarising optical microscopy (POM) and XRD studies. DSC showed that incorporation of chromophores in the side chains of polymers towards the polystyrene moiety increases the rigidity of the polymer and subsequently, its glass transition temperature; however the incorporation of side chain towards the alcoholic functional group decreases the glass transition temperature. The post derivatives do not play any significant role to increase the thermal stability ( TGA).
Resumo:
The unsymmetrical allyl containing post-metallocene complex [ArN = C( Me)] [(ArN)-N-' = C(Me)]C5H3NFeCl2 [Ar = 2,6(i- Pr)(2)C6H3, Ar' = 4-allyl-2,6-(i-Pr)(2)C6H3] (3) has been prepared and characterized. Complex (3) can be co-polymerized with styrene in the presence of radical initiator to produce polymerized post-metallocene catalyst which exhibits high activity for ethylene polymerization (2.5 x 10(6) g PE/mol Fe.h).
Resumo:
Tridentate ligand[(2,6-ArN=C(Me))(2)C5H3N](Ar=4-allyl-2,6-(i-Pr)(2)C6H3)(4)which contains allyl groups on each aryl ring was ready prepared and reacted with FeCl2. 4H(2)O to give the precatalyst [(2,6-ArN=C(CH3))(2)C5H3N]. FeCl2 (5). Compounds 2-5 were characterized by H-1 NMR, EI-MS,and IR. The complex 5 which was actived by methylaluminoxane(MAO) exhibits high activity for ethylene polymerization [1.9 x 10(6) g pE.(mol Fe . h)(-1) at 0 degreesC]. It was showed that the activity was decreased with increasing temperature and the polymer product was highly linear PE with (M) over bar (eta) varying from 50000 to 260000.