Experimental study of the beta-delayed proton decays of Er-145,Er-147

The beta-delayed proton decays of Er-145,Er-147 have been studied experimentally using the Ni-58 + Mo-92 reaction at beam energy of 383 MeV. On the basis of a He-jet apparatus coupled with a tape transport system, the beta-delayed proton radioactivities both from the nu s(1/2) ground state and the nu h(11/2) isomer in Er-145,Er-147 were observed by proton-gamma coincidence measurements. By analyzing the time distributions of the 4(+) -> 2(gamma)(+) transitions in the granddaughter nuclei Dy-144,Dy-146, the half-lives of 1.0 +/- 0.3 s and 1.6 +/- 0.2 s have been deduced for the nu h(11/2) isomers in Er-145,Er-147, respectively.

Properties of the beta-delayed proton decay of Ho-146

The proton-rich isotope Ho-148 was produced via the fusion-evaporation reaction Mo-92 (Ni-58, 3p1n). The beta-delayed proton decay of Ho-146 was studied by proton-gamma coincidence measurements using a He-jet tape transport system. The gamma-transitions in Tb-145 following the proton emissions were observed, and the beta-delayed proton branching ratios to the final states in the grand-daughter nucleus Tb-145 were determined. According to the relative branching ratios, the ground-state spin of Ho-146 has been proposed and the possible configuration discussed.

2.6 s isomer of Nd-129

Nd-129 was produced by irradiation of an enriched target of Ru-96 with a Ar-36 beam and studied by using a helium-jet fast tape transport system in combination with X-gamma and gamma-gamma coincidence measurements. A 2.6s isomer of Nd-129 was observed for the first time and tentatively proposed to be the configuration of 1/2[411].

Properties of the beta-Delayed Proton Decay of Er-147

The beta-delayed proton decay of Er-147 is studied experimentally using the Ni-58+Mo-92 reaction at a beam energy of 383 MeV. Based on a He-jet apparatus coupled with a tape transport system, the beta-delayed proton radioactivities both from the nu s(1/2) ground state and the nu h(11/2) isomer in Er-147 are identified by proton-gamma coincidence measurements. By analyzing the time distribution of the 4(+) -> 2(+) gamma transition in the grand-daughter nucleus Dy-146, a half-life of 1.6 +/- 0.2 s is determined for the nu h(11/2) isomer in Er-147. The half-life for the ground state of Er-147 is estimated to be 3.2 +/- 1.2 s.

Gamma decay of the lowly excited states of 189Re

189W activities were produced via the 192Os(n, α) reaction using irradiation of isotopically enriched 192Os metallic powder of ～100 mg/cm2 with 14 MeV neutrons. The X-γ and γ-γ coincidence measurements were made so as to obtain γ rays from 189W decay and its coincidence relations. A new simple decay scheme of 189W including three γ rays of 210.2, 229.6 and 260.2 keV is proposed. Two new levels of 189Re at 470.4 and 489.8 keV are assigned.

Test experiments of gamma-ray linear polarization using a Clover detector

We have investigated the performance of a EXOGAM-Segmented-Clover with 16 segments as a Compton polarimeter to measure the linear polarization of gamma rays. The polarization sensitivity of the Clover detector has been measured at the energy of 1332keV through the coincidence measurements of cascade gamma-rays from Co-60. Experimental values were in good accord with our expectation.We have investigated the performance of a EXOGAM-Segmented-Clover with 16 segments as a Compton polarimeter to measure the linear polarization of gamma rays. The polarization sensitivity of the Clover detector has been measured at the energy of 1332keV through the coincidence measurements of cascade gamma-rays from Co-60. Experimental values were in good accord with our expectation.

Effects of La2O3 on Microstructure and Wear Properties of Laser Clad gamma/Cr7C3/TiC Composite Coatings on TiAl Intermatallic Alloy

The effects of La2O3 addition on the microstructure and wear properties of laser clad gamma/C(r)7C(3)/TiC composite coatings on gamma-TiAl intermetallic alloy substrates with NiCr-Cr3C2 precursor mixed powders have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive spectrometer (EDS) and block-on-ring wear tests. The responding wear mechanisms are discussed in detail. The results are compared with that for composite coating without La2O3. The comparison indicates that no evident new crystallographic phases are formed except a rapidly solidified microstructure consisting of the primary hard Cr7C3 and TiC carbides and the gamma/Cr7C3 eutectics distributed in the tough gamma nickel solid solution matrix. Good finishing coatings can be achieved under a proper amount of La2O3-addition and a suitable laser processing parameters. The additions of rare-earth oxide La,03 can refine and purify the microstructure of coatings, relatively decrease the volume fraction of primary blocky Cr7C3 to Cr7C3/gamma eutectics, reduce the dilution of clad material from base alloy and increase the microhardness of the coatings. When the addition of La2O3 is approximately 4 wt.%, the laser clad composite coating possesses the highest hardness and toughness. The composite coating with 4 wt.%La2O3 addition can result the best enhancement of wear resistance of about 30%. However, too less or excessive addition amount of La2O3 have no better influence on wear resistance of the composite coating.

Microstructure and Tribological Properties of Laser Clad gamma/Cr7C3/Tic Composite Coatings on gamma-TiA1 Intermetallic Alloy

In order to improve the wear resistance of the gamma-TiAl intermetallic alloy, microstructure, room- and high-temperature (600 degrees C) wear behaviors of laser clad gamma/Cr7C3/TiC composite coatings with different constitution of NiCr-Cr3C2 precursor-mixed powders have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectrometer (EDS), block-on-ring (room-temperature) and pin-on-disk (high-temperature) wear tests. The responding wear mechanisms are discussed in detail. Results show that microstructures of the laser clad composite coatings have non-equilibrium solidified microstructures consisting of primary hard Cr7C3 and TiC carbides and the inter-primary gamma/Cr7C3 eutectic matrix, about three to five times higher average microhardness compared with the TiAl alloy substrate. Higher wear resistance than the original TiAl alloy is achieved in the clad composite coatings under dry sliding wear conditions, which is closely related to the formation of non-equilibrium solidified reinforced Cr7C3 and TiC carbides and the positive contribution of the relatively ductile and tough gamma/Cr7C3 eutectics matrix and their stability under high-temperature exposure.

Gamma -> Epsilon Martensite Transformation and Twinning Deformation in fcc Cobalt During Surface Mechanical Attrition Treatment

The deformation microstructure of face-centered cubic cobalt subjected to surface mechanical attrition treatment was studied as a function of strain levels. Strain-induced gamma --> epsilon transformation and twinning deformation were evidenced by transmission electron microscopy and were found to progress continuously in ultrafine and nanocrystalline grains as the strain increased.

等离子熔覆gamma/Cr7C3复合材料涂层组织与耐磨性研究

为探索提高工程机械易损零部件服役寿命的新技术,采用等离子熔覆工艺,以Ni-Cr-C混合合金粉末为添加材料,在易损零部件用钢Q235表面形成了以初生块状金属陶瓷Cr7C3为硬质耐磨相,以强韧性良好的γ/Cr7C3共晶为基体的复合材料冶金涂层,分析了涂层的显微组织和硬度,在室温干滑动磨损条件下测试了其耐磨性.研究结果表明:涂层组织致密,硬度较高,与基体之间为完全的冶金结合,在干滑动磨损条件下具有良好的耐磨性.

Gamma-Ray Attenuation Technique For Measuring Void Fraction In Horizontal Gas-Liquid Two-Phase Flow

The measurement of void fraction is of importance to the oil industry and chemical industry. In this article, the principle and mathematical method of determining the void fraction of horizontal gas-liquid flow by using a single-energy gamma-ray system is described. The gamma-ray source is the radioactive isotope of Am-241 with gamma-ray energy of 59.5 keV. The time-averaged value of the void fraction in a 50.0-mm i.d. transparent horizontal pipeline is measured under various combinations of the liquid flow and gas flow. It is found that increasing the gas flow rate at a fixed liquid flow rate would increase the void fraction. Test data are compared with the predictions of the correlations and a good agreement is found. The result shows that the designed gamma-ray system can be used for measuring the void fraction in a horizontal gas-liquid two-phase flow with high accuracy.

Microstructure and high-temperature wear and oxidation resistance of laser clad gamma/W2C/TiC composite coatings on gamma-TiAl intermetallic alloy

There are very strong interests in improving the high-temperature wear resistance of the y-TiAl intermetallic alloy, especially when applied as tribological moving components. In this paper, microstructure, high-temperature dry sliding wear at 600 degrees C and isothermal oxidation at 1000 degrees C on ambient air of laser clad gamma/W2C/TiC composite coatings with different constitution of Ni-Cr-W-C precursor mixed powders on TiAl alloy substrates have been investigated. The results show that microstructure of the laser fabricated composite coatings possess non-equilibrium microstructure consisting of the matrix of nickel-base solid solution gamma-NiCrAl and reinforcements of TiC, W2C and M23C6 carbides. Higher wear resistance than the original TiAl alloy is achieved in the composite coatings under high-temperature wear test conditions. However, the oxidation resistance of the laser clad gamma/W2C/TiC composite coatings is deceased. The corresponding mechanisms resulting in the above behaviors of the laser clad composite coatings are discussed. (c) 2006 Elsevier B.V. All rights reserved.

Development And Characterization Of Composite Ni-Cr-C-Caf2 Laser Cladding On Gamma-Tial Intermetallic Alloy

A process of laser cladding Ni-CF-C-CaF2 mixed powders to form a multifunctional composite coatingd on gamma-TiAl substrate was carried out. The microstructure of the coating was examined using XRD, SEM and EDS. The coating has a unique microstructure consisting of primary dendrite or short-stick TiC and block Al4C3 carbides reinforcement as well as fine isolated spherical CaF2 solid lubrication particles uniformly dispersed in the NiCrAlTi (gamma) matrix. The average microhardness of the composite coatings is approximately HV 650 and it is 2-factor greater than that of the TiAl substrate. (C) 2008 Elsevier B.V. All rights reserved.