Studies on fracture morphology of short carbon fiber reinforced poly(phenylene ether ketone)(SCF/PEK-C) composites

The shear fracture morphology of SCF/PEK-C composite with carbon fibers treated for different times was studied carefully by SEM. The result shows that the adhesion between fiber and matrix was improved and fractured model also changed from interface fracture to brittle fracture with increasing treatment time of carbon fiber. The fracture mechanism was discussed preliminary.

Studies on morphology and crystallization of polypropylene/polyamide 12 blends

Scanning electron microscopy (SEM) and an image analyser are used to study morphologies of the fractured surface, etched by hot phenol, of polypropylene/maleated polypropylene/polyamide 12 PP/PP-MA/PA12) = 65/10/25 blend and PP-MA/PA12 = 75/25 blend. The particle dimension and its distribution of PA12 dispersed phase in these blends are much lower and narrower than that of the PP/PA12. blends. Especially, most of the particles in the PP-MA/PA12 = 75/25 blend are smaller than 0.1 mu m. The effect of the morphology of PP/PA12 blends on their crystallization behaviour is studied using differential scanning calorimetry and SEM. PA12 dispersed phase coarsens during annealing in the PP/PP-MA/PA12 = 65/10/25 blend. The mechanism of coarsening of the PA12 dispersed phase is a coalescence process. The intense mixing between the PP component and the PA12 component through reaction of PP-MA and PA12 leads to a change of dynamic mechanical behaviour of the components. A separation method is used to separate the polyolefin parts (precipitated from hot phenol), from PA12 parts (hot phenol filtrate). Of PP/PP-MA/PA12 = 65/10/25 blend, infra-red measurements and elementary analysis show that the precipitate has a lower PA12 content than the feed, whereas the filtrate has a higher PA12 content. From PP-MA/PA12 = 75/25 blend, PA12 contents in the precipitate and the filtrate are the same as in the feed. This implies that all PA12 has reacted with all PP-MA in the latter case while not in the former case. Using the method of interface exposure, interfacial reaction of PP-MA with PA12 is studied by X-ray photoelectron spectrometry (X.p.s.). Copyright (C) 1996 Elsevier Science Ltd.

Miscibility and crystallization behavior of thermosetting polyimide thermoplastic polyimide blends

Compatibility, morphology, crystalline structure and mechanical properties of the blends of a thermosetting polyimide with thermoplastic polyimides consisting of dianhydrides of different lengths have been studied by the use of dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and small-angle X-ray scattering (SAXS) techniques. The results of our research show that the blends change from compatible to semi-compatible when the difference between the length of the dianhydrides of the two components increases. Addition of a thermoplastic polyimide inhibits the crystallization of the thermosetting component. However, this effect decreases with increasing length of the dianhydrides and the distribution of the molecules of the thermoplastic polyimide component changes from interlamellar to interfibrillar. Impact strength and morphology of the fractured surfaces indicate that among the semiinterpenetrating polymer networks (semi-IPN) obtained the toughening effect of the partially compatible one is the best. The results are discussed in terms of charge transfer interaction between imide group and p-phenylene group.

COMPATIBILIZATION OF HIGH-DENSITY POLYETHYLENE/POLYISOPRENE BLENDS WITH POLYETHYLENE/POLYISOPRENE THREAD-THROUGH COPOLYMERS

The compatibilization of high density polyethylene (HDPE)/polyisoprene (PI) blends with polyethylene/polyisoprene (PE/PI) ''thread-through'' copolymers was investigated. The proliferating structure of PE/PI with segments chemically identical to HDPE and PI, respectively, is different from that of graft copolymers. Studies showed that the dispersed domain size in the blends was significantly reduced and interfacial adhesion was improved by the compatibilization action of the copolymer. In the differential scanning calorimetry (DSC) analysis, the crystallization peak of HDPE in the blends became broad with adding the copolymer and fractionated crystallization appeared in the HDPE/PI blend compatibilized with the copolymer at a weight ratio of 30/70 while it appeared in the blend without copolymer at a weight ratio of 20/80. DMA results showed that by adding the copolymer, both the glass transition temperature (T-g) of the PI component and the alpha-relaxation of HDPE shifted to lower temperature, demonstrating the enhanced penetration of the two components. Mechanical properties of the blends were improved, especially the elongation at break, by the presence of the copolymers. The characteristic yielding at the fractured surface of the blends compatibilized with the copolymer indicates the fractural behavior of the material changed from brittle to tough.

SEM STUDY ON FRACTURE-BEHAVIOR OF ETHYLENE/PROPYLENE BLOCK COPOLYMERS AND THEIR BLENDS

The toughening effect of the separate phases of ethylene/propylene block copolymers and their blends was studied by scanning electron microscopy (SEM). The results obtained show that the interfacial adhesion between separate phases and the isotactic polypropene (iPP) matrix in ethylene/propylene block copolymers is strong at room temperature, but poor at low temperature; specimens exhibit tearing of separate phases during fracture at room temperature, but interfacial fracture between separate phases and the iPP matrix at low temperature. From the characteristics of fractographs of ethylene/propylene block copolymers and their blends, it could be concluded that the separate phases improve the toughness of specimens in several ways: they promote the plastic deformation of the iPP, and they can be deformed and fractured themselves during the fracture process. However, it was shown that the plastic deformation processes, such as multiple-crazing, shear yielding, etc. of the matrix are the dominant mechanisms of energy absorption in highly toughened ethylene/propylene block copolymers and their blends. The deformation and fracture of separate phases are only of secondary importance.

A comprehensive investigation of an offshore active fault in the Western Sagami Bay, central Japan

Offshore active faults, especially those in the deep sea, are very difficult to study because of the water and sedimentary cover. To characterize the nature and geometry of offshore active faults, a combination of methods must be employed. Generally, seismic profiling is used to map these faults, but often only fault-related folds rather than fracture planes are imaged. Multi-beam swath bathymetry provides information on the structure and growth history of a fault because movements of an active fault are reflected in the bottom morphology. Submersible and deep-tow surveys allow direct observations of deformations on the seafloor (including fracture zones and microstructures). In the deep sea, linearly aligned cold seep communities provide indirect evidence for active faults and the spatial migration of their activities. The Western Sagami Bay fault (WSBF) in the western Sagami Bay off central Japan is an active fault that has been studied in detail using the above methods. The bottom morphology, fractured breccias directly observed and photographed, seismic profiles, as well as distribution and migration of cold seep communities provide evidence for the nature and geometry of the fault. Focal mechanism solutions of selected earthquakes in the western Sagami Bay during the period from 1900 to 1995 show that the maximum compression trends NW-SE and the minimum stress axis strikes NE-SW, a stress pattern indicating a left-lateral strike-slip fault.

Bottom simulating reflector and gas seepage in Okinawa Trough: Evidence of gas hydrate in an active back-arc basin

To look for gas hydrate, 22 multi-channel and 3 single-channel seismic lines on the East China Sea (ECS) shelf slope and at the bottom of the Okinawa Trough were examined. It was found that there was indeed bottom simulating reflector (BSR) occurrence, but it is very rare. Besides several BSRs, a gas seepage was also found. As shown by the data, both the BSR and gas seepage are all related with local geological structures, such as mud diapir, anticline, and fault-controlled graben-like structure. However, similar structural "anomalies" are quite common in the tectonically very active Okinawa Trough region, but very few of them have developed BSR or gas seepage. The article points out that the main reason is probably the low concentration of organic carbon of the sediment in this area. It was speculated that the rare occurrence of gas hydrates in this region is governed by structure-controlled fluid flow. Numerous faults and fractures form a network of high-permeability channels in the sediment and highly fractured igneous basement to allow fluid circulation and ventilation. Fluid flow in this tectonic environment is driven primarily by thermal buoyancy and takes place on a wide range of spatial scales. The fluid flow may play two roles to facilitate hydrate formation: to help gather enough methane into a small area and to modulate the thermal regime.

Geophysical evaluation methods for buried hill reservoirs in the Jiyang superdepression of the Bohai Bay basin, eastern China

The Jiyang superdepression is one of the richest hydrocarbon accumulations in the Bohai Bay basin, eastern China. Comprehensive seismic methods have been used in buried hill exploration in Jiyang to describe these fractured reservoirs better. Accurate seismic stratigraphic demarcation and variable-velocity mapping were applied to reveal the inner structure of the buried hills and determine the nature of the structural traps more precisely. Based on the analysis of rock properties and the characteristics of well-developed buried hill reservoirs, we have successfully linked the geology and seismic response by applying seismic forward technology. Log-constrained inversion, absorption coefficient analysis and tectonic forward-inversion with FMI loggings were applied to analyse and evaluate the buried hill reservoirs and gave satisfying results. The reservoir prediction was successful, which confirmed that the comprehensive utilization of these methods can be helpful in the exploration of buried hill reservoirs.

Effect of H2S on stress corrosion cracking and hydrogen permeation behaviour of X56 grade steel in atmospheric environment

Susceptibility to stress corrosion cracking of X56 steel and its relationship with hydrogen permeation behaviour in atmospheric environment containing H2S was investigated by hydrogen permeation tests at a slow strain rate. The results show that: the fracture strain decreases with the decrease of strain rate under the same experimental conditions; the fracture strain also decreases with the increase of H2S concentration under the same strain rate, and the increased concentration of H2S has no significant effect on the hydrogen permeation in the first wet, etc. dry cycle, however has lead to increased hydrogen permeation in the later cycles. The SEM images of the fractured surfaces show clear evidences of enhanced stress corrosion cracking susceptibility by H2S.

Stress corrosion cracking of AISI 321 stainless steel in acidic chloride solution

The stress corrosion cracking (SCC) of LambdaISI 321 stainless steel in acidic chloride solution was studied by slow strain rate (SSR) technique and fracture mechanics method. The fractured surface was characterized by cleavage fracture. In order to clarify the SCC mechanism, the effects of inhibitor KI on SCC behaviour were also included in this paper. A study showed that the inhibition effects of KI on SCC were mainly attributed to the anodic reaction of the corrosion process. The results of strain distribution in front of the crack tip of the fatigue pre-cracked plate specimens in air, in the blank solution (acidic chloride solution without inhibitor KI) and in the solution added with KI measured by speckle interferometry (SPI) support the unified mechanism of SCC and corrosion fatigue cracking (CFC).

潜山油藏裂缝分布规律研究－－以辽河盆地大民屯凹陷潜山油藏为例

With the example of Damintun Depression, Liaohe Oilfield, different methods to study fracture distribution were propsosed, i.e. combined crop, core, log, with seismic attribute and paleo-stress field to predict fractural reservoir. The following conclusions are drawn: 1. Secondary fracture and dissolution pore are the main reservoir space of fractured reservoir in Damintun buried hills through observing more than 270 meters core in 27 wells. Among them, structural fracture is the main reservoir spcace in Archaean metamorphism whose main mineral are silicates, while dissolution pore and structural fracture are the main reservoir space in Protozoic carbonate which has been proved with high dissolution. Structural fracture is not only the main reservoir space but also the influent path. 2. Actual core observation and log identification proved that the formation of buried hills have the following zone: weathering crust, fracturaed zone and compact zone, among which the weathering crust and fractured zone are the main reservoir. 3. The mineralogical component of rock is the inner factor and the tectonization is the outer factor, which control the development of structural fracture. The content of brittle material in rock influences the development of structural fracture. Dissolution, chemical eluviations, weathering and fill-up affect the development of structural fracture. 4. Basement faults control the distribution of structural fracture in Damintun Depression. The trend of fracture is consistent with that of faults and there is often large-scale fractural zone around faults. 5. Based on log response, the fracture is identified with core observation, imaging well log and ANN, which can provide geological basis for optimized perforation. 6. The methods for predicting fracture with structure restoration, seismic inversion and paleo-stress simulation aiming at different types of buried-hills reservoir, and then the spatial distribution of the fracture and density is obtained, which can provide geological basis for well site adjustment.

裂缝储层预测技术应用研究

In practice,many fracture reservoir was found,which has giant potential for exporation. For example,in limestone fracture reservoir,igneous rock fracture reservoir and shale fracture reservoir ,there are high yield oil wells found. The fracture reservoir has strong anisotropy and is very difficult to explore and produce.Since 1990’s,the techniques that use structure information and P-WAVE seismic attributes to detect fracture developed very rapidly,include stress and strain analysis,using amplitude,interval velocity,time-difference,azimuthal AVO analysis etc. Based on research and develop these advanced techniques of fracture detect,this paper selected two typical fracture reservoir as target area,according to the characters of research area,selected different techniques to pridect the fracture azimuth and density of target,and at last ,confirmed the favored area. This paper includes six parts:the first chapter mainly addresses the domestic and international research actuality about the fracture prediction and the evolement in ShengLi oil field,then according to the temporal exploration requirement,a research route was established; Based on the close relationship between structural fracture and the geotectonic movement and the procedure of rock distortion，the second chapter research the structural fracture predicting technique which is realized by computing the strain in every geotectonic movement ,which is by use of the forward and inversion of the growing history of structure; The third chapter discussed many kind of traditional techniques for fracture reservoir prediction,and point out their disadvantages.then research and develop the coherence volume computing technique which can distinguish from faults,the seismic wave absorbing technique,and other fracture predicting technique which is by use of seismic attributes ,such as azimuthal AVO FVO etc; The fourth chapter first establish the geological and petrophysical model by use of the existed log and drill well information, then research the variation of amplitude and seismic wave which is caused by fractures.based on it , the fracture predicting technique which is by use of variation of azimuthal impedance is researched;The fifth chapter is a case study,it selects shale fracture reservoir in LuoJia area as target,selects several kind of techniques to apply ,at last ,the fracture distribution of target reservoir and favored area were gotten;the sixth chapter is another case study,it selects limestone fracture reservoir in BoShen6 buried hill as target,selects several kind of techniques to apply,similarly favored area were gotten. Based on deeply research and development of the new techniques for fracture reservoir exploration, This paper selects two fracture reservoirs the most typical in ShengLi as targets to be applied ,good results show up a good application way ,which can be used for reference for future fracture exploration,and it can bring materially economic and social benefit.

裂隙/孔隙型弹性介质中地震波场模拟与叠前逆时偏移

With the development of oil/gas seismic exploration, seismic survey for fracture/porosity type reservoir is becoming more and more important. As for China, since it has over 60% store of low porosity and low permeability oil/gas reservoir, it’s more urgent to validly describe fracture/porosity type oil/gas trap and proposing the related, developed seismic technique. To achieve mapping fracture/porosity region and its development status, it demands profound understanding of seismic wave propagation discipline in complex fractured/pored media. Meanwhile, it has profound scientific significance and applied worth to study forward modeling of fracture/porosity type media and pre-stacked reverse time migration. Especially, pre-stacked reverse-time migration is the lead edge technique in the field of seismology and seismic exploration. In this paper, the author has summarized the meaning, history and the present state of numerical simulation of seismic propagation in fractured/pored media and seismic exploration of fractured/pored reservoirs. Extensive Dilatancy Anisotropy (EDA) model is selected as media object in this work. As to forward modeling, due to local limitation of solving spatial partial derivative when using finite-difference and finite-element method, the author turns to pseudo-spectral method (PSM), which is based on the global characteristic of Fourier transform to simulate three-component elastic wave-field. Artifact boundary effect reduction and simulation algorithm stability are also discussed in the work. The author has completed successfully forward modeling coding of elastic wave-field and numerical simulation of two-dimensional and three-dimensional EDA models with different symmetric axis. Seismic dynamic and kinematical properties of EDA media are analyzed from time slices and seismic records of wave propagation. As to pre-stacked reverse-time migration for elastic wave-field in fractured/pored media, based on the successful experience in forward modeling results with PSM, the author has studied pre-stacked reverse-time depth-domain migration technique using PSM of elastic wave-field in two dimensional EDA media induced by preferred fracture/pore distribution. At the same time, different image conditions will bring up what kind of migration result is detailed in this paper. The author has worded out software for pre-stacked reverse-time depth-domain migration of elastic wave-field in EDA media. After migration processing of a series of seismic shot gathers, influences to migration from different isotropic and anisotropy models are described in the paper. In summary, following creative research achievements are obtained:  Realizing two-dimensional and three-dimensional elastic wave-field modeling for fractured/pored media and related software has been completed.  Proposed pre-stacked reverse-time depth-domain migration technique using PSM of elastic wave-field.  Through analysis of the seismic dynamic and kinematical properties of EDA media, the author made a conclusion that collection of multi-component seismic data can provide important data basis for locating and describing the fracture/pore regions and their magnitudes and the preferred directions.  Pre-stacked reverse-time depth-domain migration technique has the ability to reconstruct complex geological object with steep formations and tilt fracture distribution. Neglecting seismic anisotropy induced by the preferred fracture/pore distribution, will lead to the disastrous imaging results.

辽河坳陷东部凹陷火山岩构造裂缝形成机理研究及预测

In recent years, with the discovery oil and gas reservoirs in volcanic rocks, the exploration and development of these reservoirs have attracted widespread attention because of the urgent need for increasing oil and gas production in the world and volcanic rocks has currently become an important exploration target in Liaohe depression. The study area of this dissertation is in the middle section of the easternern sag of Liaohe depression that have been confirmed by studying structural fractures, which constitute a key factor impacting volcanic rocks reservoirs. Substantial reserves and large production capacity in the areas with widely distributed volcanic rocks are important reasons for examining volcanic rocks in the study area. The study began with classification and experimental data analysis of volcanic rocks fractural formation, then focused on the mechanism of fracturing and the development of volcanic rocks structural fracture prediction methodology.and Lastly, predicted volcanic rocks structural fracture before drilling involved a comprehensive study of the petroleum geology of this area, which identified favorable traps thereby reducing exploration risks and promoting the exploration and development of volcanic rocks reservoirs. 3Dstress and 3Dmove software were applied to predict structural fracture by combining the core data, well-logging data and seismic data together and making the visualization of a fracture possible. Base on the detailed fracture prediction results, well OuO48 and well Ou52 were drilled and successfully provided a basis for high efficiency exploration and development of fractured reservoir in the middle section of the eastern sag. As a result of what have been done, a new round of exploration of volcanic rocks was developed. Well OU48 and well OU52 successfully drilled in this area resulted in the in-depth study of the mechanism of structural fracture formation, technological innovation of structural fracture prediction of volcanic rocks , which guided to oil and gas exploration effectively and made it possible for high production of volcanic rocks. By the end of August 2005, the cumulative oil and gas production of Ou48 block were 5.1606 × 104 t and 1271.3× 104 m3 respectively, which made outstanding contributions to the oilfield development. Above all this work not only promoted exploration and structural fracture prediction in volcanic rocks in Liaohe depression, but also applied to in the low-permeability and fractured sandstone reservoir.

陆地三分量三维地震勘探技术研究与应用

With the development of oil and gas field exploration, it becomes harder to search new reserves. So a higher demand of seismic exploration comes up. Now 3C3D seismic exploration technology has been applied in petroleum exploration domains abroad. Comparing with the traditional P-wave exploration, the seismic attributes information which provided by 3C3D seismic exploration will increase quickly. And it can derive various combined parameters. The precision of information about lithology, porosity, fracture, oil-bearing properties, etc which estimated by above parameters was higher than that of pure P-wave exploration. These advantages mentioned above lead to fast development of 3C3D seismic technology recently. Therefore, how to apply the technology in petroleum exploration field in China, how to obtain high quality seismic data, and how to process and interpret real data, become frontier topics in geophysical field nowadays, which have important practical significance in research and application. In this paper, according to the propagation properties of P-wave and converted wave, a study of 3C3D acquisition parameters design method was completed. Main parameters included: trace interval, shot interval, maximum offset, bin size, the interval of receiving lines, the interval of shooting lines, migration aperture, maximum cross line distance, etc. Their determination principle was given. The type of 3C3D seismic exploration geometry was studied. By calculating bin attributes and analyzing parameters of geometry, some useful conclusions were drawn. With the method in this paper, real geometries for continental lithology stratum gas reservoir and fractured gas reservoir were studied and determined. In the static method of multi-wave, the near surface P-wave, S-wave parameter investigation method has been advanced, and this method has been applied for the patent successfully; the near surface P-wave, S-wave parameter investigation method and the converted refraction wave first arrival static techniques have been integrally used to improve the effectiveness of converted wave static. In the aspect of converted wave procession, the rotation of horizontal component data, the calculation of converted wave common conversion bin, the residual static of converted wave, the velocity analysis of the common conversion point (CCP), the Kirchhoff pre-stack time migration of converted wave techniques have been applied for setting up the various 3C3D seismic data processing flows based on different geologic targets, and the high quality P-wave, converted-wave profiles have been acquired in the actual data processing. In the aspect of P-wave and converted-wave comprehensive interpretation, the thoughts and methods of using zero-offset S-wave VSP data to calibrate horizon have been proposed; the method of using P-wave and S-wave amplitude ratio to predict the areas of oil and gas enrichment has been studied; the method of inversion using P-wave combined with S-wave has been studied; the various P-wave, S-wave parameters(velocity ratio, amplitude ratio, poisson ratio) have been used to predict the depth, physical properties, gas-bearing properties of reservoirs; the method of predicting the continental stratum lithology gas reservoir has been built. The above techniques have all been used in various 3D3C seismic exploration projects in China, and the better effects have been gotten. By using these techniques, the 3C3D seismic exploration level has been improved.