Perfectly Hydrophobic Silicone Nanofiber Coatings: Preparation from Methyltrialkoxysilanes and Use as Water-Collecting Substrate

Perfectly hydrophobic (PHO) coatings consisting of silicone nanofibers have been obtained via a solution process using methyltrialkoxysilanes as precursors. On the basis of thermal gravimetry and differential thermal analysis (TG-DTA) and Fourier transform infrared spectroscopy (FTIR) results, the formula of the nanofibers was tentatively given and a possible growth mechanism of the nanofibers was proposed. Because of the low affinity between the coatings and the small water droplet, when using these coatings as substrate for collecting water vapor, the harvesting efficiency could be enhanced as compared with those from bare glass substrate for more than 50% under 25 degrees C and 60-90% relative humidity. By removing the surface methyl group by heat treatment or ultraviolet (UV) irradiation, the as-prepared perfectly hydrophobic surface can be converted into a superhydrophilic surface.

Vapor permeation separation of MeOH/MTBE through polyimide/sulfonated poly(ether-sulfone) hollow-fiber membranes

Mixtures of methanol/MTBE were separated with polyimide/sulfonated poly(ether-sulfone) hollow-fiber membranes. The separation was attempted by vapor permeation instead of pervaporation, which had been used by most researchers. The separation properties of the hollow-fiber membranes and operating conditions are discussed. The results showed that separation factors of the blended polyimide/sulfonated poly(ether-sulfone) hollow-fiber membranes were extremely high for the methanol/MTBE mixtures.

Monitoring and simulation of water, heat,and CO2 fluxes in terrestrial ecosystems based on the APEIS-FLUX system

The Integrated Environmental Monitoring (IEM) project, part of the Asia-Pacific Environmental Innovation Strategy (APEIS) project, developed an integrated environmental monitoring system that can be used to detect, monitor, and assess environmental disasters, degradation, and their impacts in the Asia-Pacific region. The system primarily employs data from the moderate resolution imaging spectrometer (MODIS) sensor on the Earth Observation System- (EOS-) Terra/Aqua satellite,as well as those from ground observations at five sites in different ecological systems in China. From the preliminary data analysis on both annual and daily variations of water, heat and CO2 fluxes, we can confirm that this system basically has been working well. The results show that both latent flux and CO2 flux are much greater in the crop field than those in the grassland and the saline desert, whereas the sensible heat flux shows the opposite trend. Different data products from MODIS have very different correspondence, e.g. MODIS-derived land surface temperature has a close correlation with measured ones, but LAI and NPP are quite different from ground measurements, which suggests that the algorithms used to process MODIS data need to be revised by using the local dataset. We are now using the APEIS-FLUX data to develop an integrated model, which can simulate the regional water,heat, and carbon fluxes. Finally, we are expected to use this model to develop more precise high-order MODIS products in Asia-Pacific region.

Effects of vegetation control on ecosystem water use efficiency within and among four grassland ecosystems in China

Through 2-3-year (2003-2005) continuous eddy covariance measurements of carbon dioxide and water vapor fluxes, we examined the seasonal, inter-annual, and inter-ecosystem variations in the ecosystem-level water use efficiency (WUE, defined as the ratio of gross primary production, GPP, to evapotranspiration, ET) at four Chinese grassland ecosystems in the Qinghai-Tibet Plateau and North China. Representing the most prevalent grassland types in China, the four ecosystems are an alpine swamp meadow ecosystem, an alpine shrub-meadow ecosystem, an alpine meadow-steppe ecosystem, and a temperate steppe ecosystem, which illustrate a water availability gradient and thus provide us an opportunity to quantify environmental and biological controls on ecosystem WUE at different spatiotemporal scales. Seasonally, WUE tracked closely with GPP at the four ecosystems, being low at the beginning and the end of the growing seasons and high during the active periods of plant growth. Such consistent correspondence between WUE and GPP suggested that photosynthetic processes were the dominant regulator of the seasonal variations in WUE. Further investigation indicated that the regulations were mainly due to the effect of leaf area index (LAI) on carbon assimilation and on the ratio of transpiration to ET (T/ET). Besides, except for the swamp meadow, LAI also controlled the year-to-year and site-to-site variations in WUE in the same way, resulting in the years or sites with high productivity being accompanied by high WUE. The general good correlation between LAI and ecosystem WUE indicates that it may be possible to predict grassland ecosystem WUE simply with LAI. Our results also imply that climate change-induced shifts in vegetation structure, and consequently LAI may have a significant impact on the relationship between ecosystem carbon and water cycles in grasslands.

溶胶-凝胶光波导环形谐振腔的挥发性有机化合物传感特性

采用溶胶-凝胶法制作波导环形谐振腔, 讨论了环形谐振腔器件的传输特性。测量了在不同物质、不同体积分数的挥发性有机化合物(VOC)蒸气气氛下器件的传输光谱的敏感性。结果表明, 谐振波长随甲醇、乙醇、丙醇等醇类化合物, 以及丙酮、甲醛等蒸气体积分数的上升而向长波方向移动, 具有高的灵敏度, 且两者基本呈线性关系。其中, 对丙醇最敏感, 灵敏度达到1.403 pm/10-6。对甲烷和二甲苯也有微弱反应, 但是其灵敏度很低。也测量了水蒸气对传输谱特性的影响。观察到传输谱衬比度对不同挥发性有机化合物物质蒸气的不同敏

高真空室中的水蒸气对HfO2薄膜性能的影响

本文研究了在镀膜过程中真空室内水蒸气的含量对HfO2薄膜物理性能的影响。用电子束蒸发和光电极值监控的方法在BK7基底上制备HfO2薄膜。利用残余气体分析仪在线监测了真空室内的残余气氛组成。分别用Lambda 900光谱仪、X射线衍射方法、表面热透镜技术和1064nm的激光器测试了薄膜的光学性能、微结构、吸收和激光损伤阈值。实验发现，附加冷阱装置有助于我们有效控制镀膜过程中的水汽含量，且在水蒸气含量较少的真空室内镀制的薄膜具有较高的折射率，较小的晶粒尺寸，较低的弱吸收值和较高的损伤阈值。

Multi-channel effect of condensation flow in a micro triple-channel condenser

Multi-channel effect is important to understand transport phenomenon in phase change systems with parallel channels. In this paper, visualization studies were performed to study the multi-channel effect in a silicon triple-channel condenser with an aspect ratio of 0.04. Saturated water vapor was pumped into the microcondenser, which was horizontally positioned. The condenser was cooled by the air natural convention heat transfer in the air environment. Flow patterns are either the annular flow at high inlet vapor pressures, or a quasi-stable elongated bubble at the microchannel upstream followed by a detaching or detached miniature bubble at smaller inlet vapor pressures. The downstream miniature bubble was detached from the elongated bubble tip induced by the maximum Weber number there. It is observed that either a single vapor thread or dual vapor threads are at the front of the elongated bubble. A miniature bubble is fully formed by breaking up the vapor thread or threads. The transient vapor thread formation and breakup process is exactly symmetry against the centerline of the center channel. In side channels, the Marangoni effect induced by the small temperature variation over the channel width direction causes the vapor thread formation and breakup process deviating from the side channel centerline and approaching the center channel. The Marangoni effect further forces the detached bubble to rotate and approach the center channel, because the center channel always has higher temperatures, indicating the multi-channel effect. 

Periodic bubble emission and appearance of an ordered bubble sequence (train) during condensation in a single microchannel

Condensation of steam in a single microchannel, silicon test section was investigated visually at low flow rates. The microchannel was rectangular in cross-section with a depth of 30 pm, a width of 800 mu m and a length of 5.0 mm, covered with a Pyrex glass to allow for visualization of the bubble formation process. By varying the cooling rate during condensation of the saturated water vapor, it was possible to control the shape, size and frequency of the bubbles formed. At low cooling rates using only natural air convection from the ambient environment, the flow pattern in the microchannel consisted of a nearly stable elongated bubble attached upstream (near the inlet) that pinched off into a train of elliptical bubbles downstream of the elongated bubble. It was observed that these elliptical bubbles were emitted periodically from the tip of the elongated bubble at a high frequency, with smaller size than the channel width. The shape of the emitted bubbles underwent modifications shortly after their generation until finally becoming a stable vertical ellipse, maintaining its shape and size as it flowed downstream at a constant speed. These periodically emitted elliptical bubbles thus formed an ordered bubble sequence (train). At higher cooling rates using chilled water in a copper heat sink attached to the test section, the bubble formation frequency increased significantly while the bubble size decreased, all the while forming a perfect bubble train flowing downstream of the microchannel. The emitted bubbles in this case immediately formed into a circular shape without any further modification after their separation from the elongated bubble upstream. The present study suggests that a method for controlling the size and generation frequency of microbubbles could be so developed, which may be of interest for microfluidic applications. The breakup of the elongated bubble is caused by the large Weber number at the tip of the elongated bubble induced by the maximum vapor velocity at the centerline of the microchannel inside the elongated bubble and the smaller surface tension force of water at the tip of the elongated bubble.

Ultra-dry oxygen atmosphere to protect tellurite glass fiber from surface crystallization

In this study we report on surface crystallization phenomena and propose a solution for the fabrication of long and robust tellurite glass fibers. The bulk tellurite glasses of interest were prepared by melting and quenching techniques. Tellurite glass preforms and fibers were fabricated by suction casting and rod-in-tube drawing methods, respectively. The surfaces of the tellurite bulk glass samples and of the drawn fibers prepared under different controlled atmospheres were examined by X-ray diffraction. When the tellurite glass fibers were drawn in ambient air containing water vapor, four primary kinds of small crystals were found to appear on the fiber surface, alpha-TeO(2), gamma-TeO(2), Zn(2)Te(3)O(8) and Na(2)Zn(3)(CO(3))(4)center dot 3H(2)O. A mechanism for this surface crystallization is proposed and a solution described, using an ultra-dry oxygen gas atmosphere to effectively prevent surface crystallization during fiber drawing. (C) 2010 Elsevier B.V. All rights reserved.

黄土高原半干旱区侧柏(Platycladus orientalis)树干液流动态

应用热扩散式树干茎流计(TDP)于2008年4～10月对黄土高原安塞县侧柏人工林树干液流速率进行了连续测定,并对周围气象、土壤水分等多个环境因子进行了同步测定。结果表明:侧柏在不同月份晴天树干液流速率变化具有明显的昼夜节律性,呈单峰曲线;且各月液流速率日均值受土壤供水水平限制总体上呈下降趋势,即4月份最大,为0.00135cm.s-1;10月份最小为0.00011cm.s-1;树干液流速率与光合有效辐射、大气温度、水汽压差呈极显著正相关,与相对湿度呈负相关,其相关程度:光合有效辐射>水汽压差>大气温度>相对湿度,并可用线性表达式来估算;侧柏边材面积和地径呈幂指数关系,并以此结合密度估算出样地侧柏人工林的边材面积为4.65m2,最终估算出侧柏人工林生长季总耗水量为1159.6t.hm-2。

黄土高原半干旱区人工林刺槐展叶期树干液流动态分析

应用热扩散式树干茎流计(TDP)于2008年4月26日至5月31日,在黄土高原半干旱区安塞县对人工林刺槐展叶期树干液流及其气象、土壤水分等6个指标进行连续测定。结果表明:刺槐展叶期可分为芽期、展叶初期、中期和全叶期。在芽期,刺槐树干液流速率日变化无明显昼夜波动;在展叶初期至全叶期日变化呈现出从微弱波动逐渐增大到趋于平稳的剧烈波动;在展叶中期以后液流速率表现为上升快、下降缓慢的单峰曲线;在全叶期平均峰值约为0.0027cm.s-1;树干液流速率与光合有效辐射强度、大气温度、水蒸气压亏缺和风速呈极显著正相关,与相对湿度呈负相关,其相关程度依次为光合有效辐射强度>大气温度>水蒸气压亏缺>相对湿度>风速,且可用光合有效辐射强度和大气温度线性表达式来估测;土壤水分在展叶期呈逐渐减少趋势,但对树干液流的胁迫不显著;在展叶期刺槐单株日蒸腾耗水量随直径的增大而增大并与胸径呈良好的线性关系,可用来估算展叶期刺槐人工林蒸腾耗水量。

长白山地区近50年气候变化及其预估

收集长白山地区15个气象站1953-2007年气温、降水、蒸发、日照时数和水汽压观测数据和国家气候中心整理的2001-2099年的 气温、降水预估资料，利用数理统计方法，系统分析长白山地区气候现状、变化及其预估，为气候变化对人类生存环境影响研究并制定适应对策提供依据。主要结论如下： 1.长白山地区气温、降水日数、日照时数和不同界限温度（≥0℃、≥5℃、≥10℃和<0℃）积温均有显著趋势。年极端最低、年平均、平均最高/最低气温和气温日/年较差在1984、1992、1995、1985、1972和1979年发生突变。所有最高/最低气温与日照百分率有显著负相关关系，一定程度是温室效应结果；最高、最低气温变化不同步造成气温日较差和年较差的非对称性。 2.长白山地区生长季节合计降水量和降水强度日际变化较大。降水以7月30日为界，呈现前升后降极显著的线性趋势，且发生均值突变。降水强度以6月27日和9月3日为分界点，分为三个阶段。降水集中度、集中期和集中时段时空非均一性分布明显。 3.在SRES A1B、SRES A2和SRES B1三种情景下年平均气温均为上升趋势，年内变化一致为冬季升温最迅速，夏季则相对缓慢；而年降水强度总体增加，年内变化比较一致：冬季增加最为明显，而夏季变化不大。 4.未来长白山地区各站≥0℃、≥5℃和≥10℃的积温均有不同程度增加，持续时间延长。负积温增加，持续时间缩短，开始日期推迟，而结束时间提前。

Preparation and performance of cellulose acetate/polyethyleneimine blend microfiltration membranes and their applications

A modified microfiltration membrane has been prepared by blending a matrix polymer with a functional polymer. Cellulose acetate (CA) was blended with polyethyleneimine (PEI), which was then crosslinked by polyisocyanate, in a mixture of solvents. In the membrane, PEI can supply coupling sites for ligands in affinity separation or be used as ligands for metal chelating, removal of endotoxin or ion exchange. The effects of the time of phase inversion induced by water vapor, blended amount of PEI and amount of crosslinking agent on membrane performance were investigated. The prepared blend membranes have specific surface area of 12.04-24.11 m(2)/g and pure water flux (PWF) of 10-50 ml/cm(2) min with porosity of 63-75%. The membranes, made of 0.15 50 wt.% PEI/CA ratio and 0.5 crosslinking agent/PEI ratio, were applied to adsorbing Cu2+ and bovine serum albumin (BSA) individually. The maximum adsorption capacity of Cu2+ ion on the blend membrane is 7.42 mg/g dry membrane. The maximum adsorption capacities of BSA on the membranes with and without chelating Cu2+ ion are 86.6 and 43.8 mg/g dry membrane, respectively. (C) 2004 Elsevier B.V. All rights reserved.

Direct reduction of SO2 to elemental sulfur by the coupling of cold plasma and catalyst (I)

The direct reduction of SO2 to elemental sulfur in flue gas by the coupling of cold plasma and catalyst, being a new approach for SO2 reduction, was studied. In this process, CO2 can be disassembled to form CO, which acts as the reductant under the cold plasma. With the coupling of the cold plasma and the catalyst, sulfur dioxide was selectively reduced by CO to elemental sulfur with a byproduct of metal sulfate, e.g., FeSO4. In the present work, Fe2O3/gamma-Al2O3 was employed as the catalyst. The extent of desulfurization was more than 80%, and the selectivity of elemental sulfur is about 55%. The effects of water vapor, temperature, and the components of simulated flue gas were investigated. At the same time, the coupling of thermogravimetry and infrared method and a chemical analysis method were employed to evaluate the used catalyst. In this paper, we will focus on the discussion of the catalyst. The discussions of the detail of plasma will be introduced in another paper.