基于ActiveX Scripting技术的测试软件开发

测试软件(Tester)的开发不同于一般的软件开发,在测试软件开发的过程中,涉及到测试软件本身和测试用例(Testcase)两者之间的划分和协作.目前的测试用例脚本大都是一些自定义的格式文本,通过测试软件的分析来执行测试逻辑,不仅需要编写大量复杂的脚本解析程序,而且难以阅读和维护.为了解决这个问题,提出了一种基于ActiveX Scripting技术的测试软件开发方法,该方法可以将测试逻辑按照需求分配到测试软件和测试用例,提供了一种统一的编程接口,易于学习和使用.

电磁式纳米压入仪的载荷精度研究

纳米压入仪(Nanoindenter)已成为纳米/微米力学测试的基本工具之一,广泛应用于纳米材料、薄膜、MEMS微结构的力学性能测试。目前商业化仪器有MTS NanoIndenter(incorporated into Agi lent in 2008),Hysitron TriboIndenter,CSM NanoHardness Tester,MML NanoTest,and CSIRO UMIS,其中原MTS Nano Indenter、CSMNano Hardness Tester和MML NanoTest都采用电磁驱动兼载荷计量的原理设计。这类仪器主要优点之一是载荷分辨力高,可以达到50nN甚至更小。然而仪器制造商从未明确给出此类仪器的载荷精度。目前对纳米压痕测试技术的研究也主要集中在压头形状、试样表面粗糙度、毛细力等因素对压痕测试结果的影响,尚未见针对仪器载荷精度的研究报道。国际标准ISO 14577-2:2002虽对仪器施加的试验力的允差进行了规定,但由于电磁式纳米压入仪的结构响应和试样力学行为耦合在一起,试样上的载荷并不完全等同于通过电磁转换原理计量的试验力,因此实际测试时试样上的载荷精度仍是未知。

计算机控制的亚微米硬度计及其应用

本文描述了一台有微机控制的可变温亚微米深度灵敏的硬度计及其应用实例。该硬度计的负荷范围从0.01N到2N负荷测量精度为1mN。为该硬度计配备了各种角度的四棱锥型，三棱锥型和Knoop型金刚压头用来得到各种不同的深度面积比。利用该硬度计研究了测量中的压痕尺寸效应（ISE）马氏体不锈钢辐照和He注入后的硬化脆化效应，连接奥氏体不锈钢焊接材料和碳--金属焊接材料的辐照效应。同时，还研究了在稳定负荷下硬度与加压时间的关系（压痕蠕变）和在循环负荷下硬度与循环次数的关系（压痕疲劳）

Instrumented impact testing of phenolphthalein polyether ketone

The Charpy impact fracture behaviour of unnotched specimens of phenolphthalein polyether ketone (PEK-C) was studied over a temperature range from room temperature to 220 degrees C by using an instrumented impact tester. The load-time and energy-time curves of PEK-C at different temperatures were recorded. From these curves, some important parameters, such as the maximum impact load, the maximum stress, the total impact energy, the crack initiation energy, the crack propagation energy etc., were obtained and their temperature dependences of PEK-C were investigated. The point of 100 percent maximum load on the load-time trace was shown to be the yield point. Two parameters, the ductile ratio (D.R.) and the ductility index (D.I.) were applied to characterize the ductility of PEK-C and their relationships to the relaxation processes were discussed.

Effect of physical aging on phenolphthalein polyethersulfone/poly(phenylene sulfide) blend .1. Mechanical properties

The effect of physical aging at 210 degrees C on the mechanical properties of phenolphthalein polyether sulfone (PES-C) and a PES-C/poly(phenylene sulfide) (PPS) blend, with 5% content of PPS, were studied using DMA, tensile experiments, an instrumented impact tester, and SEM observations. The blend shows good mechanical properties in comparison with the corresponding PES-C. The mechanical properties of both materials exhibit characteristics of physical aging, with only the aging rate of the blend relatively slower, which should be attributed to the constraint effect of PPS particles and the good interfacial adhesion. The morphology of the PPS phase in the blend did not change with aging time. The principal role of PPS particles is to induce crazes, which dissipate energy, under applied loading; thus, the blend shows good toughness. On the other hand, the multiple crazing mechanism depends on the molecular mobility or structural state of the matrix. (C) 1996 John Wiley & Sons, Inc.

THE IZOD IMPACT FRACTURE-BEHAVIOR OF PHENOLPHTHALEIN POLY(ETHER KETONE)

The Izod impact fracture behaviour of notched specimens of phenolphthalein poly(ether ketone) (PEK-C) has been studied over a temperature range from room temperature to 240 degrees C by using an instrumented impact tester. The temperature dependence of the maximum load, total impact energy, initiation energy, propagation energy, ductility index (DI) and the relationships between these parameters and the relaxation processes have been investigated.

THE CHARPY IMPACT FRACTURE-BEHAVIOR OF PHENOLPHTHALEIN POLYETHER KETONE

The Charpy impact fracture behavior of notched specimens of phenolphthalein poly(ether ketone) (PEK-C) has been studied over a range of temperature using a JJ-20 Model instrumented impact tester. For PEK-C, there exist two temperature regions which distinguish the fracture mechanism, and the brittle fracture was preferentially governed by slip or shear bands at relatively high temperatures, but by crazes at low temperatures. The temperature dependence of the ductility index (DI) shows similar peaks to the tan delta loss. (C) 1995 John Wiley and Sons, Inc.

TEMPERATURE EFFECT ON IMPACT FRACTURE-TOUGHNESS AND FRACTURE MECHANISM OF PHENOLPHTHALEIN POLY(ETHER KETONE)

Phenolphthalein poly(ether ketone) (PEK-C) was tested using an instrumented impact tester to determine the temperature effect on the fracture toughness K-c and critical strain energy release rate G(c). Two different mechanisms, namely the relaxation processes and thermal blunting of the crack tip were used to explain the temperature effect on the fracture toughness. Examination of the fracture surfaces revealed the presence of crack growth bands. It is suggested that these bands are the consequence of variations in crack growth along crazes that are formed in the crack tip stress field. As the crack propagates, the stress is relaxed locally, decreasing the growth rate allowing a new bundle of crazes to nucleate along which the crack advances.

Screening of genes related to ovary development in Chinese shrimp Fenneropenaeus chinensis by suppression subtractive hybridization

The ovary of triploid shrimp Fenneropenaeus chinensis was apparently impaired compared to that of the diploid shrimp at the same age. Therefore triploid shrimp ovary is possible to be taken as a model to understand the mechanism of ovary development of shrimp compared to that of the ovary of diploid shrimp at the same age. In the present study, a suppression subtractive hybridization (SSH) technique was applied to identify differentially expressed genes in the ovary between diploid and triploid shrimp. For the forward library (RNA from the ovary of triploid shrimp as the tester), 54 genes were identified. For the reverse library (RNA from the ovary of diploid shrimp as the tester), 16 genes were identified. The identified genes encoded proteins with multiple functions, including extracellular matrix components, cytoskeleton, cell growth and death, metabolism, genetic information processing, signal transduction/transport or immunity related proteins. Eleven differentially expressed genes were selected to be confirmed in the ovaries of triploid and diploid shrimp by semi-quantitative RT-PCR. Genes encoding spermatogonial stem-cell renewal factor, cytochrome c oxidase subunits I and II, clottable protein, antimicrobial peptide and transposase showed up-regulated expressions in the ovary of triploid shrimp. Genes encoding tubulin, cellular apoptosis susceptibility protein, farnesoic acid O-methyltransferase, thrombospondin and heat shock protein 90 genes showed higher expressions in the ovary of diploid shrimp. The differential expressions of the above genes are suggested to be related to the ovary development of shrimp. It will provide a new clue to uncover the molecular mechanisms underlying the ovarian development in penaeid shrimp. (C) 2010 Elsevier Inc. All rights reserved.

非自喷层测试及评价解释技术研究与应用

Now low porosity and low permeability reservoir is one of the main targets of exploration for the onshore oilfields of China. Most of the reservoirs are none flowing because of bad formation percolation condition, poor gas oil ratio , low formation pressure coefficient and other factors. In the recent years, a number of domestic oilfields have carried out some research work and achieved some success on oil testing and production technology in such formation. But by now, there is still no systematic and mature technology, particularly testing technology in none flowing formation is still needed further study. Based on study the key problem of well testing and interpretation technology in none flowing formation, solve the important problems in well testing technology, continuously improve and innovate geological information acquisition technology for none flowing reservoir, accurately acquire boundary information and evaluate reservoir flow characteristics. Its wide application remarkable result has shown. The main results and cognitions obtained from research are as follows: 1. This new technology research results help solve the occurrent problems in well testing process for none flowing formations, such as small investigation radius, poor representative of interpretation results from the poor data, low level application of interpretation results. This new technology helps create favorable conditions for early precise reservoir evaluation and reduction of the risk of exploration. 2. The technological difficulties for none flowing well testing are successfully solved by using none flowing formation combined mechanical tool string .This method has been proved by its applications to be able to improve the efficiency of the testing and the quantity of the acquired test data ,and so as to enhance the application of the interpretation results of the test in development of oil fields. 3. The application of the rotary formation tester, selective test valve, well testing string and their allier tools help to resolve problems such as the operation of opening and shutting-in the well under different well conditions, to broaden the scope of well test technology for none flowing formations. 4. Refined Testing Technique for production Wells has greatly shortened the testing dwration and improved the efficiency and accuracy of operation, enriched test results, and at the same time created conditions for conducting multi-well interference well testing.