大尺度流域不同地貌类型区水土保持减水效益分析

趋势分析结果显示 ,河源涧区、风沙区、丘陵区各代表流域年径流量均在 1970年前后发生一致性改变 ,即从 1970年以来开始有明显的减少趋势 ,平均减流幅度 (与 195 9～ 196 9年径流相比 )以河源涧区 (大理河 )和丘陵区 (小理河 )最大 ,分别为 36 .33%和 36 .2 1% ,风沙区 (海流兔河 )最小 (2 0 .6 1% )。减流幅度的大小是各类型区下垫面状况、水土保持措施和治理程度、降雨量变化等多种因素综合作用的结果。借助适合于黄土高原降雨 -产流特性的月水量平衡改进模型 ,计算天然状态下降雨应有的产流量与同期实测径流量求得减水效果。结果表明 ,3个地貌类型区 70年代的减水效益没有明显差异 ,而在 80年代减水效果差异显著 ,丘陵区 (小理河 ,2 4.99% ) >风沙区 (海流兔河 ,17.2 8% ) >河源涧区 (大理河 ,13.13% )。上述结论为定量评价黄土高原生态环境建设对黄河水资源及水环境演变的影响提供了数据基础。

北黄海表层沉积物粒度分布特征及其对沉积环境的指示

本文基于北黄海1140个表层沉积物样品的粒度分析结果，来探讨沉积物粒度组成、分布特征与物源和水动力环境的关系。结果表明，研究区底质类型主要有泥、粉砂、砂质粉砂、粉砂质砂、砂五种类型，少数站位含有砾石。砾石则主要分布在长山列岛附近海域、大连湾口及其东南近海；砂主要分布在123.3°E以东的海域和长山列岛附近海域；粉砂主要分布在研究区的西南部和大连湾外海；粘土的含量较低，含量大于30%的区域仅分布在研究区的西南部，大于16%的区域有向北和东北延伸的趋势，在大连湾至广鹿岛近海沉积物粘土含量也大于16%。 根据对沉积物粒度各粒级的因子分析结果,结合沉积物的Folk分类和Pejrup分类,将北黄海划分成五个主要沉积环境分区，分别受山东半岛沿岸流、黄海暖流、强潮流场、长山列岛和辽东沿岸流控制。北黄海中西部沉积物主要受山东半岛沿岸流影响，经过本区的黄海暖流限制了山东半岛沿岸流携带的细粒物质向东和向北的扩散和运移，研究区东部沉积作用的主控因素是潮流，长山列岛中部海域受附近岛屿剥蚀物影响，大连湾外海受辽东半岛沿岸流控制。研究区西南部细粒沉积物的粒度分布具有不均匀性和南北不对称性，其形成主要受控于山东半岛沿岸流和黄海暖流及其相互作用，潮流可能也起一定作用。

Cannibalism in Japanese flounder juveniles, Paralichthys olivaceus, reared under controlled conditions

Laboratory experiments were conducted to determine the effects of sand substratum, light, starvation, fish density and size variation on cannibalism among Japanese flounder juveniles, Paralichthys olivaceus. Cannibalistic behavior (biting and swallowing) increased significantly with starvation except in darkness, where juveniles could not find and attack their prey. Cannibalism occurred more frequently in heterogeneous than in the homogeneous size groups. Cannibalism was more frequent in light than in darkness at each starvation level. With sufficient food present, sand had no significant effect on cannibalism among homogeneous size juveniles, but played an important role in discouraging predation among members of the heterogeneous size groups. With sufficient food present, the rate of cannibalism was generally low and there were no significant differences in cannibalism among fish density levels of the homogeneous juveniles, With starvation, the cannibalism rate was significantly higher in high density groups than in the lower ones. Our results indicate that size variation, starvation and Light are the major factors affecting cannibalism in flounder juveniles, while sand and fish density only have a limited effect on cannibalism, depending on the nature of other factors. (C) 2000 Elsevier Science B.V. All rights reserved.

Corrosion of mild steel in different granularity seabed sediment saturated with seawater

In order to investigate the corrosion of pipeline materials in Seabed Sediment (SBS) environment, weight-loss and electrochemical measurements in saturated sand and mud cells with seawater were performed for a simulation. The used electrochemical measurements included linear polarization resistance (LPR) and potentiodynamic scanning measurement. It was showed that the corrosion rate of mild steel in the present condition was lower than the corrosion rate of other marine environment corrosion zones of it; that the granularity of SBS could affect the corrosion behavior greatly; that with increasing grain size of SBS, the corrosion rate increased. Integrated over the results of the weight loss and polarization curves, the oxygen diffusion (oxygen as a depolarizant agent) mechanism was proposed and discussed.

Study on steel corrosion in different seabed sediments

A series of simulation experiments on carbon steel (A(3) steel) and low alloy steel (16 Mn steel) in marine atmosphere (MA), seawater (SW) and seabed sediment (SBS) including rough sea sand, fine sea sand and seabed mud were carried out indoors for a year or so by means of individually hanging plates (IHP) and electrically connected hanging plates (ECHP). The corrosion of steels in SBS was mainly due to the macrogalvanic cell effect. The steel plates at the bottom of SBS, as the anode of a macrogalvanic cell, showed the heaviest corrosion with a corrosion rate of up to 0.12 mm/a, approximately equal to that of steel plates in marine atmosphere. The test results showed that the corrosion rates of A(3) and 16 Mn steel in marine environment were in the order: MA > SW > SBS by the IHP method; and MA > SBS > SW by the ECHP method. The corrosion rates of steels in the water/sediment interface were directly proportional to the grain size of the SBS by the ECHP method, but those of steels in the water/sediment interface did not vary with the grain size of SBS by the IHP method. The corrosion rate of low-alloy steel was a little higher than that of carbon steel. The results of this study have important applications for design of offshore steel structures such as oil platform, pier, and port.

黄骅坳陷港西开发区河流相储层构型与剩余油分布模式研究

In the production tail of oilfield, water-cut is very high in thick channel sand oil reservoir, but recovery efficiency is relative low, and recoverable remaining oil reserves is more abundant, so these reserves is potential target of additional development. The remaining oil generally distributed with accumulation in certain areas, controlled by the reservoir architecture that mainly is the lateral accretion shale beddings in the point bar, so the study of reservoir architecture and the remaining oil distribution patterns controlled by architecture are very significant. In this paper, taking the Minghuazhen formation of Gangxi oilfield as a case, using the method of hierarchy analysis, pattern fitting and multidimensional interaction, the architecture of the meandering river reservoir is precisely anatomized, and the remaining oil distribution patterns controlled by the different hierarchy architecture are summarized, which will help to guide the additional development of oil fields. Not only is the study significant to the remaining oil forecasting, but also it is important for the theory development of reservoir geology. With the knowledge of sequence correlation and fluvial correlation model, taking many factors into account, such as combination of well and seismic data, hierarchical controlling, sedimentary facies restraint, performance verification and 3-D closure, an accurate sequence frame of the study area was established. On the basis of high-resolution stratigraphic correlation, single layer and oil sand body are correlated within this frame, and four architecture hierarchies, composite channel, single channels, point bars and lateral accretion sandbody are identified, The result indicates that Minghuazhen Formation of Gangxi oilfield are dominated by meandering river deposition, including two types of channel sandbodies, narrow band and wide band channel sandbody, and each of them has different characteristics of facies variation laterally. Based on the identification of composite channel, according to the spatial combination patterns and identified signs of single channel, combined with channel sandbody distribution and tracer material data, single channel sandbodies are identified. According to empirical formula, point-bar scales of the study area are predicted, and three identification signs are summarized, that is, positive rhythm in depositional sequence, the maximum thick sand and near close to the abandoned channel, and point bars are identified. On the basis of point bar recognition, quantitative architecture models inner point bar are ascertained, taking the lateral accretion sand body and lateral accretion shale beddings in single well as foundation, and quantitative architecture models inner point bar as guidance, and result of tracer material data as controlling, the the lateral accretion sand body and lateral accretion shale beddings are forecasted interwell, so inner architecture of point bar is anatomied. 3-D structural model, 3-D facies model and 3-D petrophysical properties models are set up, spatial distribution characteristics of sedimentary facies and petrophysical properties is reappeared. On the basis of reservoir architecture analysis and performance production data, remaining oil distribution patterns controlled by different hierarchy architecture units, stacked channel, single channel and inner architecture of point bar, are summarized, which will help to guide the additional development of oil fields.

东海陆架盆地复杂天然气藏地震勘探判别技术研究

Exploration study proves that East sea shelf basin embeds abundant hydrocarbon resources. However, the exploration knowledge of this area is very low. Many problems in exploration are encountered here. One of them is that the gas reservoir of this area, with rapid lateral variation, is deeply buried. Correlation of Impendence between sandstone, gas sand and shale is very poor. Another problem is that the S/N ratio of the seismic data is very low and multiples are relatively productive which seriously affect reservoir identification. Resolution of the seismic data reflected from 2500-3000 meter is rather low, which seriously affects the application of hydrocarbon direct identification (HDI) technology. This research established a fine geological & geophysical model based on drilling、well logging、geology&seismic data of East sea Lishui area. A Q value extraction method from seismic data is proposed. With this method, Q value inversion from VSP data and seismic data is performed to determine the subsurface absorption of this area. Then wave propagation and absorption rule are in control. Field acquisition design can be directed. And at the same time, with the optimization of source system, the performance of high resolution seismic acquisition layout system is enhanced. So the firm foundation is ensured for east sea gas reservoir exploration. For solving the multiple and amplitude preserving problems during the seismic data processing, wave equation pre-stack amplitude preservation migration and wave equation feedback iteratively multiple attenuation technologies are developed. Amplitude preservation migration technology can preserve the amplitude of imaging condition and wave-field extrapolation. Multiple removing technology is independent of seismic source wavelet and velocity model, which avoiding the weakness of Delft method. Aiming at the complicated formation condition of the gas reservoir in this area, with dissecting typical hydrocarbon reservoir, a series of pertinent advanced gas reservoir seismic identification technologies such as petrophysical properties analyzing and seismic modeling technology、pre-stack/post-stack joint elastic inversion, attribute extraction technology based on seismic non-stationary signal theory and formation absorption characteristic and so on are studied and developed. Integrated analysis of pre-stack/post-stack seismic data, reservoir information, rock physics and attribute information is performed. And finally, a suit of gas reservoir identification technology is built, according to the geological and geophysical characteristics of this area. With developed innovative technologies, practical application and intergrated interpretation appraisal researches are carried out in Lishui 36-1.The validity of these technologies is tested and verified. Also the hydrocarbon charging possibility and position of those three east sea gas exploration targets are clearly pointed out.

叠前叠后联合反演技术及其在QHD32-6油田的应用研究

What geophysical inversion studied includes the common mathematics physical property of inversion and the constitution and appraisal method of solution in geophysics domain, i.e. using observed physical phenomenon from the earth surface to infer space changing and physical property structure of medium within the earth. Seismic inversion is a branch of geophysical inversion. The basic purpose of seismic inversion is to utilizing seismic wave propagating law in the medium underground to infer stratum structure and space distribution of physical property according to data acquisition, processing and interpretation, and then offer the vital foundation for exploratory development. Poststack inversion is convenient and swift, its acoustic impedance inversion product can reflect reservoir interior changing rule to a certain degree, but poststack data lack abundant amplitude and travel time information included in prestack data because of multiple superimpose and weaken the sensitiveness which reflecting reservoir property. Compared with poststack seismic inversion, prestack seismic inversion has better fidelity and more adequate information. Prestack seismic inversion, including waveform inversion, not only suitable for thin strata physical property inversion, it can also inverse reservoir oil-bearing ability. Prestack seismic inversion and prestack elastic impedance inversion maintain avo information, sufficiently applying seismic gathering data with different incident angle, partial angle stack, gradient and intercept seismic data cube. Prestack inversion and poststack inversion technology were studied in this dissertation. A joint inversion method which synthesize prestack elastic wave waveform inversion, prestack elastic impedance inversion and poststack inversion was proposed by making fully use of prestack inversion multiple information and relatively fast and steady characteristic of poststack inversion. Using the proposed method to extract rock physics attribute cube with clear physical significance and reflecting reservoir characterization, such as P-wave and S-wave impedance, P-wave and S-wave velocity, velocity ratio, density, Poisson ratio and Lame’s constant. Regarding loose sand reservoir in lower member of Minghuazhen formation, 32-6 south districts in Qinhuangdao,as the research object, be aimed at the different between shallow layer loose sand and deep layer tight sand, first of all, acquire physical property parameters suitable for this kind of heavy oil pool according to experimental study, establishing initial pressure and shear wave relational model; Afterwards, performing prestack elastic wave forward and inversion research, summarizing rules under the guidance of theoretical research and numerical simulation, performing elastic impedance inversion, calculating rock physics attributes; Finally, predicting sand body distribution according to rock physics parameters, and predicting favorable oil area combine well-logging materials and made good results.

中国东部沙地物源示踪及地质意义

Heavy mineral assemblages, chemical compositions of diagnostic heavy minerals such as garnet and tourmaline, and U-Pb ages and Hf isotopic compositions of zircons are very effective means to determine sediment provenance. An integrated application of the above provides insight on the lithologies, crystallization ages and crustal formation ages of the parent magma of sediment source areas. As a result, the locations and characteristics of potential source areas can be constrained and contributions of different source regions may be evaluated. In addition, the study provides evidence for the magmatic and tectonic history of source areas using a novel approach. The heavy mineral assemblages, and chemical compositions of detrital garnets and tourmalines, U-Pb ages and Hf isotopic compositions of zircons for sand and loess samples deposited since the Last Glacial Maximum (LGM) from the Hulunbeier, Keerqin and Hunshandake sandlands were analyzed and compared to those of central-southern Mongolia, the central Tarim and surrounding potential source areas, the Central Asian Orogenic Belt (CAOB) and North China Craton (NCC). The following remarks on provenance and tectonic history can be made: 1. The source compositional characteristics of the Hulunbeier, Keerqin and Hunshandake sandlands are similar. They are derived from the CAOB and NCC whose contributions for the Keerqin and Hunshandake sandland are about 50%. For the Hulunbeier sandland it is somewhat less, about 40%. 2. Loesses around of the sandlands have the identical source signiture as the sands, implying that they are sorted by the same wind regime. 3. The source characteristics of the present and LGM sands are the same, providing direct evidence that the present sands originated from the reworking of LGM sands. 4. The provenance characteristics of the three sandlands differ from those of the Tarim. As a result, the possibility that the three eastern sandlands were sourced from the Taklimakan desert can be ruled out. 5. The source compositions of sand samples derived from the CAOB indicate that the occurrence of Archean and Paleoproterozoic metamorphic basement rocks is limited and continuous subduction-accretion events from the Neoproterozoic to the Mesozoic occurred. This implies that the CAOB is a orogenic collage belt similar to the present day southwest-Pacific, and formed by the amalgamation of small forearc and backarc ocean basins occurring between island arcs and microcontinents during continuous collision and accretion. The Hf isotopic signitures of detrital zircons indicate that large amounts of juvenile mantle materials were added to the CAOB crust during the Phanerozoic.

非均质储层叠前地震反演技术研究及应用

(1) I research on the relationship between elastic parameters, lithology and liquid. It is a physical base for pre-stack seismic inversion. I research all kinds of approximate expressions of Zoeppritz function. Then the relation of all kinds of approximate expressions can be confirmed. The geological model of water sand and gas sand in different depth was designed. Moreover I research on precision of all kinds of approximate expressions. (2) In process of seismic data which aim at amplitude recovery and apply in pre-stack seismic inversion, I advance to adopt double flow chart for different aim. Pre-stack noise elimination, real amplitude recovery and NMO correction of long offset are the key taches. (3) I made a systemic expatiate for the thinking and applicability about all kinds of expressions of elastic impedance. And mathematical model was applied to compare the precision with all kinds of expressions of elastic impedance. I propose a new pre-stack simultaneous inversion which is based on the Zoppritz function and simulated annealing algorithm. This method can ensure calculation precision of reflection coefficient from different incident angle and get a global optimum solution. Therefore this method improves the precision of pre-stack seismic inversion. (4) The object function of P-S wave pre-stack simultaneous inversion was established. I compared the precision and convergence between simultaneous inversion and P-wave inversion. And the results show that simultaneous inversion is superior to P-wave inversion. Through the study of AVO event of transformed wave, AVO characters of different kinds of gas sand were analyzed. (5) I carried out the study work of pre-stack seismic inversion for carbonate reservoir in middle of Tarim basin and sand shale reservoir in Sulige Area of Erdos Basin. The method and technology in this paper was applied to practical work. And I made a prediction for heterogeneous reservoir. Moreover it acquires a good application effect. Key Word: reflection coefficient， amplitude recovery， pre-stack seismic inversion， Heterogeneous reservoir，prediction.

末次冰盛期以来中国东部沙地空间分布特征及环境记录

The latest two extreme scenarios of last glacial maximum and Holocene climatic optimum marked extreme situations in China. This paper aims to reconstruct the fossil extensions and paleoclimate of deserts in eastern China during this typical period. Aeolian sequence responds the climate change by virtue of alternation of aeolian sand layer and sandy soil layer, which correspond aridity and humidity, respectively. There is a set of contrastive deposits made up of loose sand layer and overlying dark sandy soil below land surface. This developed soil and underlying deep aeolian sand respond to H.O. and late last glacial, i.e. LGM. The typical bottom sand layers of about 50 profiles of Hulun Buir Desert, Horqin Desert and Otindag Desert were dated using OSL to confirm that they did deposid in LGM. Based on the locations of these LGM sand, distrution of gobi-desert-loess and landform control, the distribution in LGM of the three deserts were reconstructed. For the block of eastern mountain, the extreme eastern boundary of Hulun Buir Desert and Otindag Desert are not just functioned by climate background. The east of Horqin Desert is plain, hence eastern boundary of this desert is maily controlled by climate. It is considered that quite a lot of aeolian sand of LGM origined from fluvial deposit by observing regional distribution of river and SEM of sand grains. The environment alternation of of LGM-H.O. is featured by extensive expanse of active dune in LGM and grassland in H.O. Combined grain-size, susceptibility, TOC, colour and SEM measurement, the OSL chronology of relatively continued profiles since LGM of the three deserts are divided into four periods: eolian sand (15-10ka)- sandy soil (10-5ka)- alternation of black sand and yellow sand- reworking of LGM sand as destroy of soil.

松辽盆地古龙地区葡萄花油层组沉积成岩相研究

The sediment and diagenesis process of reservoir are the key controlling factors for the formation and distribution of hydrocarbon reservoir. For quite a long time, most of the research on sediment-diagenesis facise is mainly focusing on qualitative analysis. With the further development on exploration of oil field, the qualitative analysis alone can’t meet the requirements of complicated requirements of oil and gas exploreation, so the quantitative analysis of sediment-diagenesis facise and related facies modling have become more and more important. On the basis of the research result from stratum and sediment on GuLong Area Putaohua Oil Layer Group, from the basic principles of sedimentology, and with the support from the research result from field core and mining research results, the thesis mainly makes the research on the sediment types, the space framework of sands and the evolution rules of diagenesis while mainly sticking to the research on sediment systement analysis and diagenetic deformation, and make further quantitative classification on sediment-diageneses facies qualitatively, discussed the new way to divide the sediment-diagenesis facies, and offer new basis for reservoir exploration by the research. Through using statistics theory including factor analysis, cluster analysis and discriminant analysis, the thesis devided sediment-diagenesis facies quantitatively. This research method is innovative on studying sediment-diagenesis facies. Firstly, the factor analysis could study the main mechanism of those correlative variables in geologic body, and then could draw a conclusion on the control factors of fluid and capability of reservoir in the layer of studying area. Secondly, with the selected main parameter for the cluster analysis, the classification of diagenesis is mainly based on the data analysis, thus the subjective judgement from the investigator could be eliminated, besides the results could be more quantitative, which is helpful to the correlative statistical analysis, so one could get further study on the quantitative relations of each sediment-diagenesis facies type. Finally, with the reliablities of discriminant analysis cluster results, and the adoption of discriminant probability to formulate the chart, the thesis could reflect chorisogram of sediment-diagenesis facies for planar analysis, which leads to a more dependable analytic results.According to the research, with the multi-statistics analysis methods combinations, we could get quantitative analysis on sediment-diagenesis facies of reservoir, and the final result could be more reliable and also have better operability.

细粒沉积物多组分粒度特征及其成因机制研究

By using high-resolution laser grain size instrument Mastersizer 2000, the grain size distribution of windblown depositions (loess and sandy dunes), aqueous sediments (lake, river, riverside and foreshore sand), weathering crust, sloping materials and other fine-grain sediments are systemically measured. The multimodal characteristics of grain size distribution of these sediments are carefully studied. The standard patterns and their grain size characteristics of various sediments are systemically summarized. The discrepancies of multimodal distribution among windblown depositions, aqueous sediments and other sediments are concluded and the physical mechanisms of grain size multimodal distribution of various sediments are also discussed in this paper. The major conclusions are followed: 1. The multimodal characteristic of grain size distribution is a common feature in all sediments and results from properties of transportation medium, dynamic intensity, transportation manner and other factors. 2. The windblown depositions are controlled by aerodynamic forcing, resulting in that the median size of the predominant mode gradually decreases form sandy dunes to loess. Similarly, the aqueous sediments are impacted by dynamic forces of water currents and the median grain size of the predominant mode decreases gradually from river to lake sediments. Because the kinetic viscidity of air is lower than of water, the grain size of modes of windblown depositions is usually finer than that of corresponding modes of aqueous sediments. Typical characteristics of sediments grain size distribution of various sediments have been summarized in the paper: (1) Suspended particles which diameters are less than 75μm are dominant in loess and dust. There are three modes in loess’ grain size distribution: fine, median and coarse (the median size is <1μm、1-10μm、10-75μm, respectively). The coarse mode which percentage is larger than that of others is controlled by source distance and aerodynamic intensity of dust source areas. Some samples also have a saltation mode which median size is about 300-500μm. Our analysis demonstrates that the interaction of wind, atmospheric turbulence, and dust grain gravity along the dust transportation path results in a multimodal grain size distribution for suspended dust. Changes in the median sizes of the coarse and medium modes are related to variation in aerodynamic forcing (lift force related to vertical wind and turbulence) during dust entrainment in the source area and turbulence intensity in the depositional area. (2) There is a predominant coarse saltation mode in grain size distribution of sandy dunes, which median size is about 100-300μm and the content is larger than that of other modes. The grain size distribution curve is near axis symmetric as a standard logarithm normal function. There are some suspended particles in some samples of sandy dunes, which distribution of the fine part is similar to that of loess. Comparing with sandy samples of river sediments, the sorting property of sandy dunes is better than of river samples although both they are the saltation mode. Thus, the sorting property is a criterion to distinguish dune sands and river sands. (3) There are 5~6 modes (median size are <1μm, 1-10μm, 10-70μm, 70-150μm, 150-400μm, >400μm respectively) in grain size distribution of lacustrine sediments. The former 4 modes are suspensive and others are saltated. Lacustrine sediments can be divided into three types: lake shore facies, transitional facies and central lake facies. The grain size distributions of the three facies are distinctly different and, at the same time, the transition among three modes is also clear. In all these modes, the third mode is a criteria to identify the windblown deposition in the watershed. In lake shore sediments, suspended particles are dominant, a saltation mode sometimes occurs and the fourth mode is the most important mode. In the transitional facies, the percentage of the fourth mode decreases and that of the second mode increases from lake shore to central lake. In the central lake facies, the second mode is dominant. A higher content of the second mode indicates its position more close to the central lake. (4) The grain size distribution of river sediments is the most complex. It consist of suspension, saltation and rolling modes. In most situations, the percentage of the saltation mode is larger than that of other modes. The percentage of suspension modes of river sediments is more than of sandy dunes. The grain size distribution of river sediments indicates dynamic strength of river currents. If the fourth mode is dominant, the dynamic forcing of river is weaker, such as in river floodplain. If the five or sixth mode is dominant, the water dynamic forcing of rivers is strong. (5) Sediments can be changed by later forcing in different degree to form some complicated deposition types. In the paper, the grain size distribution of aqueous sediments of windblown deposition, windblown sediments of aqueous deposition, weathering crust and slope materials are discussed and analyzed. 3. The grain size distribution characteristics of different sediments are concluded: (1) Modal difference: Usually there are suspended and saltation modes in the windblown deposition. The third mode is dominant in loess dust and the fifth mode is predominant in sandy dunes. There are suspended, saltation and rolling particles in aqueous sediments. In lacustrine sediments, the second and fourth mode are predominant for central lake facies or lake shore facies, respectively. In river sediments, the fourth, or fifth, or sixth mode is predominant. Suspended modes: the grain size of suspended particles of windblown depositions usually is less than 75μm. The content of suspended particles is lower or none in sandy dunes. However, suspended particles of aqueous sediments may reach 150μm. Difference in grain size of suspended modes represents difference between transitional mediums and the strength of dynamic forcing. Saltation modes: the median size of saltation mode of sandy dunes fluctuates less than that of river sediments. (2) Loess dust and lacustrine sediment: Their suspended particles are clearly different. There is an obvious pit between the second and the third modes in grain size distribution of lacustrine sediments. The phenomenon doesn’t occur in loess dust. In lacustrine sediments, the second mode can be a dominant mode, such as central lake facies, and contents of the second and the third modes change reversely. However, the percentage of the third mode is always the highest in loess dust. (3) Dune Sand and fluvial sand: In these two depositions, the saltation particles are dominant and the median sizes of their saltation modes overlay in distribution range. The fifth mode of dune sand fluctuates is sorted better than that of fluvial sand. (4) Lacustrine and fluvial sediments: In lacustrine sediments, there are 5-6 modes and suspended particles can be predominant. The second mode is dominant in central lake facies and the third mode is dominant in lake shore facies. Saltation or roll modes occurred in central lake facies may indicate strong precipitation events. In fluvial sediments, saltation particles (or rolling particles) usually dominant. 4. A estimation model of lake depth is firstly established by using contents of the second, the third and the fourth modes. 5. The paleoenvironmental history of the eastern part of SongLiao basin is also discussed by analyzing the grain size distribution of Yushu loess-like sediments in Jilin. It was found that there is a tectonic movement before 40ka B.P. in SongLiao basin. After the movement, loess dust deposited in Yushu area as keerqin desert developed. In recent 2000 years, the climate became drier and more deserts activated in the eastern part of Song-Liao basin.

安塞油田三叠系延长组长10油层组沉积相研究

Ordos basin is a large-scale craton overlapping basin, which locates in western North China platform and possesses abundant hydrocarbon resources. Ansai area in 2007 to extend the head of Chang10 of Yangchang Formation has made breakthrough progress in the region, long a high of Gao52 was Chang10 industrial oil flow, for oil exploration Ansai Oil Field opened a new chapter. in 2008, high of Gao52, Wang519, Gao34 producing wells area of building and found the existence of Chang10 great potential for the discovery of Chang10 Reservoir, Ansai Oil Field for a new direction, showing a good exploration development prospects.The study of occurrence and distribution features of hydrocarbon should be made by new theories and evolutions of sedimentology, sequence stratigraphy, reservoir sedimentology and petroleum geology form different angles on the base of regional geology background. Ansai Oil Field is in mid Shanbei Slope, which is a considerable producing zone of Ordos basin. Chang10 of Yangchang Formation is an important oil-bearing series, which sedimentary formation was formed in Indosinian orogeny, Late Triassic, sedimentary background is a momentary uplifting in Ordos basin, and exploration and exploitation of hydrocarbon in this area is very important. To further descripte disciplinarian of accumulation hydrocarbon, carefully study on sedimentary facies, reservoir type and disciplinarian of accumulation hydrocarbon of Chang10 of Yangchang Formation in study area is needed. By collecting date of field profile, outcrop, core and many other geological, through sedimentary and oil geological analysis, sedimentary facies types were identified, distributing of sedimentary facies and extension of sand body were analyzed too. Finally, the main controlling factors of hydrocarbon and the favorable areas were found out by deeply studying sedimentary system and disciplinarian of accumulation oil&gas in Chang10 of Yangchang Formation, Late Triassic in Ansai Oil Field. Chang10 of Yangchang Formation is main study formation, which is divided into three members (Chang101, Chang102 and Chang103), Chang101 is subdivided into three (Chang1011, Chang1012and Chang1013) reservoirs. By defining Layered borderline between every member and detailed describing rock and electro characteristic, member zonation become more reasonable and accurate also sedimentary facies and disciplinarian of accumulation oil&gas in study area are confirmed Through researching sedimentary facies, reservoir sand and hydrocarbon migration, accumulation, distribution, hydrocarbon accumulation models of Chang10 of Yangchang Formation in study area is pointed out, which is lithologic hydrocarbon reservoir and tectonic-lithologic hydrocarbon reservoir. Different play is formed by different processes and factors. Through analysis of reservoir property, trap type and accumulation model, several favorable exploration areas can be found out in Chang 10 reservoirs （Chang1011, Chang1012and Chang1013） of the Ansai Oil Field.

溶蚀岩体渗透水力学特性研究

Seepage control in karstic rock masses is one of the most important problems in domestic hydroelectric engineering and mining engineering as well as traffic engineering. At present permeability assessment and leakage analysis of multi-layer karstic rock masses are mainly qualitative, while seldom quantitative. Quantitative analyses of the permeability coefficient and seepage amount are conducted in this report, which will provide a theoretical basis for the study of seepage law and seepage control treatment of karstic rocks. Based on the field measurements in the horizontal grouting galleries of seepage control curtains on the left bank of the Shuibuya Hydropower Project on the Qingjiang river, a hydraulic model is established in this report, and the computation results will provide a scientific basis for optimization of grouting curtain engineering. Following issues are addressed in the report. (1) Based on the in-situ measurements of fissures and karstic cavities in grouting galleries, the characteristics of karstic rock mass is analyzed, and a stochastic structural model of karstic rock masses is set up, which will provide the basis for calculation of the permeability and leakage amount of karstic rock mass. (2) According to the distribution of the measured joints in the grouting galleries and the stochastic results obtained from the stochastic structural model of karstic rock mass between grouting galleries, a formula for computation of permeability tensor of fracturing system is set up, and a computation program is made with Visual Basic language. The computation results will be helpful for zoning of fissured rock masses and calculation of seepage amount as well as optimization of seepage control curtains. (3) Fractal theory is used to describe quantitatively the roughness of conduit walls of karstic systems and the sinuosity of karstic conduits. It is proposed that the roughness coefficient of kastic caves can be expressed by both fractal dimension Ds and Dr that represent respectively the extension sinuosity of karstic caves and the roughness of the conduit walls. The existing formula for calculating the seepage amount of karstic conduits is revised and programmed. The seepage amount of rock masses in the measured grouting galleries is estimated under the condition that no seepage control measures are taken before reservoir impoundment, and the results will be helpful for design and construction optimization of seepage curtains of the Shuibuya hydropower project. This report is one part of the subject "Karstic hydrogeology and the structural model and seepage hydraulics of karstic rock masses", a sub-program of "Study on seepage hydraulics of multi-layer karstic rock masses and its application in seepage control curtain engineering", which is financially supported by the Hubei Provincial key science and technology programme.