(Ga, Gd, As) film growth on GaAs substrate by low-energy ion-beam deposit

(Ga, Gd, As) film was fabricated by the mass-analyzed dual ion-beam epitaxy system with the energy of 1000 eV at room temperature. There was no new peak found except GaAs substrate peaks (0 0 2) and (0 0 4) by X-ray diffraction. Rocking curves were measured for symmetric (0 0 4) reflections to further yield the lattice mismatch information by employing double-crystal X-ray diffraction. The element distributions vary so much due to the ion dose difference from AES depth profiles. The sample surface morphology indicates oxidizing layer roughness is also relative to the Gd ion dose, which leads to islandlike feature appearing on the high-dose sample. One sample shows ferromagnetic behavior at room temperature. (C) 2003 Elsevier B.V. All rights reserved.

激波诱导含灰气体边界层中的粒子分布

本文研究当激波沿着一个固体表面等速地穿越含灰气体运动时所诱导的层流边界层特性。考虑了作用在气体边界层中球形粒子的 Saffman 升力,建议了一种计算近壁区中弥散相密度剖面的方法,并给出了数值计算结果。本文结果表明:在激波后方存在着一个弯曲的薄层区域,其中的粒子密度可以比其波前原始值增加许多倍。这种粒子聚集效应对于工业中粉尘爆炸等实际问题具有重要意义。

天然淡水冰单轴压缩强度及其温度和应变率效应

本文报道了在不同温度和不同应变率下天然淡水冰单轴压缩强度的实验结果。指出S—l型柱状晶粒冰的压缩强度随着温度的降低而增加,极限压缩强度在应变率为10~(-4)S(-1)时有一个最大值。本实验的应变率范围是10~(-5)—10~0s~(-1)。10~(-1)—10~0s~(-1)的应变率范围是在冲击速度lm/s左右的实验条件下获得的,这个速度接近于浮冰与海上结构物相撞的情况。以本实验为基础,有希望发展对海冰的实验技术。

A coupled model for multiphase fluid flow and sedimentation deformation in oil reservoir and its numerical simulation

A mathematical model for coupled multiphase fluid flow and sedimentation deformation is developed based on fluid-solid interaction mechanism. A finite difference-finite element numerical approach is presented. The results of an example show that the fluid-solid coupled effect has great influence on multiphase fluid flow and reservoir recovery performances, and the coupled model has practical significance for oilfield development.

Internal resonance of an L-shaped beam with a limit stop .1. Free vibration

Real-life structures often possess piecewise stiffness because of clearances or interference between subassemblies. Such an aspect can alter a system's fundamental free vibration response and leads to complex mode interaction. The free vibration behaviour of an L-shaped beam with a limit stop is analyzed by using the frequency response function and the incremental harmonic balance method. The presence of multiple internal resonances, which involve interactions among the first five modes and are extremely complex, have been discovered by including higher harmonics in the analysis. The results show that mode interaction may occur if the higher harmonics of a vibration mode are close to the natural frequency of a higher mode. The conditions for the existence of internal resonance are explored, and it is shown that a prerequisite is the presence of bifurcation points in the form of intersecting backbone curves. A method to compute such intersections by using only one harmonic in the free vibration solution is proposed. (C) 1996 Academic Press Limited

Internal resonance of an L-shaped beam with a limit stop .2. Forced vibration

A limit stop is placed at the elbow of an L-shaped beam whose linear natural frequencies are nearly commensurable. As a result of this hardening device the non-linear system exhibits multiple internal resonances, which involve various degree of coupling between the first five modes of the beam in free vibration. A point load is so placed as to excite several modes and the resulting forced vibration is examined. In the undamped case, three in-phase and two out-of-phase solution branches have been found. The resonance curve is extremely complicated, with multiple branches and interactions between the first four modes. The amplitudes of the higher harmonics are highly influenced by damping, the presence of which can effectively attenuate internal resonances. Consequently parts of the resonance curve may be eliminated, with the resulting response comprising different distinctive branches. (C) 1996 Academic Press Limited

二维槽道湍流的标度律分析

对不同Reynolds数的二维不可压槽道湍流（即二维槽道流动的扰动饱和态）进行了标度律分析。指出二维槽道湍流中存在明显的标度律及扩展自相似性；分析了标度数随着流动Reynolds数的变化，指出随着Reynolds数的增长，标度指数的奇异性并没有减小的趋势；由此推测充分发展的二维槽道湍流的标度指数也是奇异的。将所得计算值和佘振苏等人的SL标度律预测值相比较，认为佘等人的SL标度律公式能很好描述二维湍流。

A Study of the Tribological Behavior of Carbon-Nanotube-Reinforced Ultrahigh Molecular Weight Polyethylene Composites

The tribological properties of the high-strength and high-modulus ultrahigh molecular weight polyethylene (UHMWPE) film and the UHMWPE composites reinforced by multiwalled carbon nanotubes (MWCNT/UHMWPE) were investigated using a nanoindenter and atomic force microscope (AFM). The MWCNT/UHMWPE composites films exhibited not only high wear resistance but also a low friction coefficient compared to the pure UHMWPE films. We attribute the high wear resistance to the formation of the new microstructure in the composites due to the addition of MWCNTs.

Flow similariy applied in convection-based tilt sensor

The environment temperature has inevitable effects on property of the convect ion-based tilt sensors. It not only redefines the application, but also prevents the improvement of the sensor performance. Numerical simulation of the fluid flow in the chamber of a sensor was performed and the influence of the environment temperature was studied in this paper. At zero tilt angle, the temperature distribution along the perpendicular line cross the heat source at various environment temperatures was presented. It was found that the flow varied dramatically at different environment temperatures, which would cause the output signal vary accordingly, even when the tilt angle was kept at a constant, because this device works by sensing the change of flow. At the same condition, we present the numerical results when the temperature difference across the heat source and the environment was kept at the same, in those results, it was found that the temperature difference at every point along the perpendicular line cross the heat source keep the same, this result confirms the similarity principle of nature convection. Second, A method of eliminating environment temperature infect on property of convect ion-based tilt sensor, which is based on the theory of flow similarity, is proposed. It was found that a thermal transistance can be piped on the circuit of heat source to compensate the temperature of the heat source. A compensative circuit was specially designed which can keep flow similarity by changing heat source temperature in order to eliminate the influence of environment temperature. The experiment results show that above 70% temperature drift can be eliminated by this compensative circuit.

槽道湍流的直接数值模拟

通过直接数值模拟(DNS)研究槽道湍流的性质和机理。包含五个部分：1）湍流直接数值模拟的差分方法研究。2）求解不可压N－S方程的高效算法和不可压槽道湍流的直接数值模拟。3）可压缩槽道湍流的直接数值模拟和压缩性机理分析。4）“二维湍流”的机理分析。5）槽道湍流的标度律分析。1．针对壁湍流计算网格变化剧烈的特点，构造了基于非等距网格的的迎风紧致格式。该方法直接针对计算网格构造格式中的系数，克服了传统方法采用 Jacobian 变换因网格变化剧烈而带来的误差。针对湍流场的多尺度特性分析了差分格式的精度、网格尺度与数值模拟能分辨的最小尺度的关系，给出不同差分格式对计算网格步长的限制。同时分析了计算中混淆误差的来源和控制方法，指出了迎风型紧致格式能很好地控制混淆误差。2．将上述格式与三阶精度的Adams半隐格式相结合，构造了不可压槽道湍流直接数值模拟的高效算法。该算法利用基于交错网格的离散形式的压力Poisson方程求解压力项，避免了压力边界条件处理的困难。利用FFT对方程中的隐式部分进行解耦，解耦后的方程采用追赶法（LU分解法）求解，大大减少了计算量。为了检验该方法，进行了三维不可压槽道湍流的直接数值模拟，得到了Re＝2800的充分发展不可压槽道湍流，并对该湍流场进行了统计分析。包括脉动速度偏斜因子在内的各阶统计量与实验结果及Kim等人的计算结果吻合十分理想，说明本方法是行之有效的。3．进行了三维充分发展的可压缩槽道湍流的直接数值模拟。得到了 Re=3300，Ma=0.8的充分发展可压槽道湍流的数据库。流场的统计特征（如等效平均速度分布，“半局部”尺度无量纲化的脉动速度均方根）和他人的数值计算结果吻合。得到了可压槽道湍流的各阶统计量，其中脉动速度的偏斜因子和平坦因子等高阶统计量尚未见其他文献报道。同时还分析了压缩性效应对壁湍流影响的机理，指出近壁处的压力－膨胀项将部分湍流脉动的动能转换成内能，使得可压湍流近壁速度条带结构更加平整。4．模拟了二维不可压槽道流动的饱和态（所谓“二维湍流”），分析了“二维槽道湍流”的非线性行为特征。分析了流场中的上抛－下扫和间歇现象，研究了“二维湍流”与三维湍流的区别。指出“二维湍流”反映了三维湍流的部分特征，同时指出了展向扰动对于湍流核心区发展的重要性。5．首次对可压缩槽道湍流及“二维槽道湍流”标度律进行了分析，得出了以下结论：a）槽道湍流中，在槽道中心线附近较宽的区域，存在标度律。b）该区域流场存在扩展自相似性（ESS）。c）在Mach数不是很高时，压缩性对标度指数影响不大。本文结果同SL标度律的理论值吻合较好，有效支持了该理论。对“二维槽道湍流”也有相似的结论，但与三维湍流不同的是，“二维槽道湍流”存在标度律的区域更宽，近壁处的标度指数比中心处有所升高。

Prediction of Effective Moduli of Carbon Nanotube-Reinforced Composites with Waviness and Debonding

Carbon nanotubes (CNTs) have been regarded as ideal reinforcements of high-performance composites with enormous applications. However, the waviness of the CNTs and the interfacial bonding condition between them and the matrix are two key factors that influence the reinforcing efficiency. In this paper, the effects of the waviness of the CNTs and the interfacial debonding between them and the matrix on the effective moduli of CNT-reinforced composites are studied. A simple analytical model is presented to investigate the influence of the waviness on the effective moduli. Then, two methods are proposed to examine the influence of the debonding. It is shown that both the waviness and debonding can significantly reduce the stiffening effect of the CNTs. The effective moduli are very sensitive to the waviness when the latter is small, and this sensitivity decreases with the increase of the waviness. (C) 2008 Elsevier Ltd. All rights reserved.

An Integrated Evolutionary Algorithm for Expensive Global Optimization

We propose an integrated algorithm named low dimensional simplex evolution extension (LDSEE) for expensive global optimization in which only a very limited number of function evaluations is allowed. The new algorithm accelerates an existing global optimization, low dimensional simplex evolution (LDSE), by using radial basis function (RBF) interpolation and tabu search. Different from other expensive global optimization methods, LDSEE integrates the RBF interpolation and tabu search with the LDSE algorithm rather than just calling existing global optimization algorithms as subroutines. As a result, it can keep a good balance between the model approximation and the global search. Meanwhile it is self-contained. It does not rely on other GO algorithms and is very easy to use. Numerical results show that it is a competitive alternative for expensive global optimization.

Time-resolved investigation of low-density plasma channels produced by a kilohertz femtosecond laser in air

By employing pump-probe back longitudinal diffractometry, the electron density and decay dynamics of a weak plasma channel created by a 1-KHz fs laser in air has been investigated. With ultrashort laser pulses of 50 fs and low energy of 0.6 mJ, we observe weak plasma channels with a length similar to 2 cm in air. An analytical reconstruction method of electron density has been analyzed, which is sensitive to the phase shift and channel size. The electron density in the weak plasma channel is extracted to be about 4x10(16) cm(-3). The diameters of the plasma channel and the filament are about 50 and 150 mu m, respectively, and the measurable electron density can be extended to less than 10(15) cm(-3). Moreover, a different time-frequency technique called linearly chirped longitudinal diffractometry is proposed to time-resolved investigate ultrafast ionization dynamics of laser-irradiated gas, laser interaction with cluster beam, etc.

Space-frequency coupling, conical waves, and small-scale filamentation in water

Numerical simulations of fs laser propagation in water have been made to explain the small-scale filaments in water we have observed by a nonlinear fluorescence technique. Some analytical descriptions combined with numerical simulations show that a space-frequency coupling mainly from the interplay among self-phase modulation, dispersion and phase mismatching will reshape the laser beam into a conical wave which plays a major role of energy redistribution and can prevent laser beam from self-guiding over a long distance. An effective group velocity dispersion is introduced to explain the pulse broadening and compression in the filamentation. (c) 2005 American Institute of Physics.