超声与磁粉强化含单宁废水生物处理研究

单宁是一种典型的有毒难降解污染物，在制革、造纸、制药、印染等行业废水中广泛存在，对水环境造成污染并且影响废水生物处理效果。本研究针对含单宁废水生物处理效率低、较高浓度时微生物受抑制且污泥容易膨胀等问题，采用超声和磁粉来强化含单宁废水生物处理，研究超声和磁粉对微生物活性、污染物去除及污泥沉降性能的影响，并对其作用机理进行了分析和探讨。 研究结果表明，活性污泥系统中单宁酸容积负荷可以达到1.8kgCOD/(m3·d)，单宁酸和COD去除率分别达到85.2%和79.6%，但如果负荷进一步增大则微生物活性迅速降低。系统在pH 5~8、温度20~35℃、DO>1 mg/L的条件下具有较好的单宁酸降解效果和处理稳定性。单宁降解动力学参数为：μmax =0.208h-1；Ks=226mg/L；Ki=522mg/L；kd=0.0092h-1；Y =0.594。 磁粉对系统处理效果和污泥沉降性能有一定的促进作用，且效果要优于外磁场。适宜的磁粉粒径和投加量分别为0.05~0.15mm和1.0g/L，COD去除率比对照系统提高6.4%，SVI降低28.6%，污泥絮体结构紧密。磁粉强化主要是通过其对污泥菌胶团的凝聚、吸附作用以及对微生物活性的强化作用实现。 在适当强度（0.4W/cm2）和辐照时间（20min）的超声作用下污泥絮体和细胞膜通透性增大，酶分泌也增多，系统的COD去除率比对照提高了8.8%，单宁酶酶活提高了11%。但超声也使污泥絮体结构松散，沉降性能下降，SVI比对照系统升高9.3%。 由于污泥流失加剧导致污泥浓度相对较低，声磁联合强化系统相对于磁粉强化系统其处理效果并没有提高。但相对于单纯活性污泥系统，声磁联合作用下系统处理效果、污泥沉降性能以及系统运行稳定性都得到明显改善。本研究为难降解废水的生物处理提供了一个新的思路。 Tannins are typical refractory and toxic pollutants that commonly exist in wastewater from dye, medicine, paper and leather industries and cause many problems associated with environmental pollution and biological treatment of wastewater. Biological treatment efficiency of tannin-containing wastewater is usually low owing to its biological toxicity and low biodegradability, microbes are usually inhibited under high tannin concentration and sludge bulking frequently occurs. In this study, ultrasound and magnetic powder were used to improve the biological treatment performance of simulated tannic acid-containing wastewater. The effects of ultrasonic irradiation and magnetic powder on microbial activity, tannic acid degradation rate and sludge sedimentation were investigated. The augmentation mechanisms were analyzed and discussed. The experimental results showed that the microbes were prominently inhibited under high tannic acid concentration, but moderate degradation efficiency can be maintained under a tannic acid load of up to 1.8kgCOD/(m3·d), with the tannic acid degradation and COD removal percentage of 85.2% and 79.6% respectively. The highest degradation rates and treatment stability were achieved at pH range of 5~8, temperature range of 20~35℃ and DO concentration of above 1mg/L. The kinetic parameters were estimated, including: μmax =0.208h-1；Ks=226mg/L；Ki=522mg/L；kd=0.0092h-1；Y =0.594. The microbial activity, tannic acid degradation rate and sludge sedimentation were improved by adding Fe3O4 magnetic powder, and the augmentation performance was better than external magnetic field. The appropriate particle size and dosage of magnetic powder were found to be 0.05~0.15mm and 1.0g/L, respectively, under which the COD removal percentage was improved by 6.4% and SVI value decreased by 28.6%, and compact floc structure was observed. This was mainly caused by the flocculation and adsorption effects of magnetic powder against sludge floc and the stimulation of microbial activity under appropriate magnetic field. Under appropriate ultrasonic irradiation (ultrasonic intensity 0.4W/cm2, ultrasonic irradiation time 20min), the permeability of floc and cell membrane are improved, transfer of substrate and oxygen were reinforced; meanwhile, more enzyme were produced by microbes under the slight damage caused by ultrasound. However, the floc structure became loose under ultrasonic irradiation, leading to relatively poor sedimentation, with the SVI value 9.3% higher than the control system. Although the magnetic powder-ultrasonic irradiation combined augmentation system showed no improvement in treatment performance compared with sole magnetic augmentation system owing to its relatively low sludge concentration, it guaranteed the stable operation of system, meanwhile the tannic acid degradation and sludge sedimentation were significantly improved compared with sole activated sludge system. This study gives a new idea for biological treatment of refractory wastewater.

Simultaneous determination of both the calibration constant in an electrochemical quartz crystal microbalance and the active surface area of a polycrystalline gold electrode

A novel method is employed for the simultaneous determination of both the calibration constant of an electrochemical quartz crystal microbalance (EQCM) and the active surface area of a polycrystalline gold electrode. A gold electrode: is immersed into a 1 mM KI/1 M H2SO4 solution and on which forms a neutral monolayer. The adsorbed iodine can then be completely oxidized into IO3-. The active surface area of a gold electrode can be obtained from the net electrolytic charge of the oxidation process, and the calibration constant in the EQCM can be calculated from the corresponding frequency shift. The result shows that this method is simple, convenient and valid. (C) 2000 Elsevier Science S.A. All rights reserved.

A preliminary study on chemistry of phenoxynaphthacenequinones

A preliminary study on the chemistry of 6-phenoxy-5,12-naphthacenesuinone derivatives was reported, It was found that the main product was 6-(N,N-dimethylamino)-5,12-naphthacenequinone when a reaction of 6-chloro-5,12-naphthacenequinone with 4-hydroxyazobenzenes in DMF was carried out under certain reaction conditions. When the reaction of 6-[4-(4-hydroxyphenyl)isopropyl)phenoxy]-5, 12-naphthacenequinone and epichlorohydrin was carried out in an acetone/DMF(V/V=2/1) mixed solvent and in the presence of K2CO3 and KI, a new phenoxynaphthacenequinone derivative,6,6'-[1-methylethylidenebis(4,1-phenyleneoxy)]bis(5,12-naphthacenequinone), was obtained.

萃取-非水介质氢化物发生-ICP-AES中的干扰及Ni-Fe基合金的分析

本文结合溶剂萃取研究了非水介质中氢化物发生-ICP-AES的分析条件、干扰等因素的影响。利用KI~+H_2SO_4/MIBK萃取体系将As,Sb,Bi萃取到MIBK中而与基体元素分离,然后将该有机相与甲酸按等体积混合后,即可直接进行氢化物发生-ICP-AES分析。还对影响萃取和氢化物发生的一些因素及共存元素的干扰进行了讨论。该方法应用于Ni-Fe基合金中As和Sb的分析,取得了较满意的结果。

Particle-attached and free-living bacterial communities in a contrasting marine environment: Victoria Harbor, Hong Kong

Diversity of particle-attached and free-living marine bacteria in Victoria Harbor, Hong Kong, and its adjacent coastal and estuarial environments was investigated using DNA fingerprinting and clone library analysis. Denaturing gradient gel electrophoresis (DGGE) analysis of 16S rRNA genes showed that bacterial communities in three stations of Victoria Harbor were similar, but differed from those in adjacent coastal and estuarine stations. Particle-attached and free-living bacterial community composition differed in the Victoria Harbor area. DNA sequencing of 28 bands from DGGE gel showed Alphaproteobacteria was the most abundant group, followed by the Bacteroidetes, and other Proteobacteria. Bacterial species richness (number of DGGE bands) differed among stations and populations (particle-attached and free-living; bottom and surface). BIOENV analysis indicated that the concentrations of suspended solids were the major contributing parameter for the spatial variation of total bacterial community structure. Samples from representative stations were selected for clone library (548 clones) construction and their phylogenetic distributions were similar to those of sequences from DGGE. Approximately 80% of clones were affiliated to Proteobacteria, Bacteroidetes and Cyanobacteria. The possible influences of dynamic pollution and hydrological conditions in the Victoria Harbor area on the particle-attached and free-living bacterial community structures were discussed.

Particle-attached and free-living bacterial communities in a contrasting marine environment: Victoria Harbor, Hong Kong

Diversity of particle-attached and free-living marine bacteria in Victoria Harbor, Hong Kong, and its adjacent coastal and estuarial environments was investigated using DNA fingerprinting and clone library analysis. Denaturing gradient gel electrophoresis (DGGE) analysis of 16S rRNA genes showed that bacterial communities in three stations of Victoria Harbor were similar, but differed from those in adjacent coastal and estuarine stations. Particle-attached and free-living bacterial community composition differed in the Victoria Harbor area. DNA sequencing of 28 bands from DGGE gel showed Alphaproteobacteria was the most abundant group, followed by the Bacteroidetes, and other Proteobacteria. Bacterial species richness (number of DGGE bands) differed among stations and populations (particle-attached and free-living; bottom and surface). BIOENV analysis indicated that the concentrations of suspended solids were the major contributing parameter for the spatial variation of total bacterial community structure. Samples from representative stations were selected for clone library (548 clones) construction and their phylogenetic distributions were similar to those of sequences from DGGE. Approximately 80% of clones were affiliated to Proteobacteria, Bacteroidetes and Cyanobacteria. The possible influences of dynamic pollution and hydrological conditions in the Victoria Harbor area on the particle-attached and free-living bacterial community structures were discussed.

Community structure and seasonal dynamics of planktonic ciliates along salinity gradients

The ciliate community structure and seasonal dynamics in a solar saltern of the Yellow Sea were studied based oil 4 sampling dates and 8 stations with salinities from 27.7 parts per thousand to 311.0 parts per thousand. The effects of the type and concentration of the fixative used (Lugol's and Bouin's) were tested at the first sampling date. Fixative type and fixative concentration had significant effects on ciliate abundance and blovolume, with 1% Lugol's giving the best results. A detailed investigation using live observations and protargol staining techniques revealed a total of 98 morphospecies from 8 sampling stations. There was obvious seasonal variation in species composition at most of the stations, but this tended to be less distinct with increasing salinity, as the dominant ciliate group shifted from oligotrichs to heterotrichs. Ciliate abundance varied from 4.40 x 10(1) to 2.11 x 10(5) cells l(-1) and biomass ranged between 2.39 and 9.87 x 10(3) mu g Cl-1 (at a salinity of 147.6 parts per thousand). Both abundance and biomass decreased abruptly when salinity exceeded 100-150 parts per thousand. Statistical analyses Suggested that the dynamics of ciliate abundance and biomass were regulated by both salinity and by season, but those of diversity and species richness were mainly controlled by salinity and both significantly decreased with increasing salinity. (C) 2009 Elsevier GmbH. All rights reserved.

Morphology and Molecular Phylogeny of Trimyema koreanum n. sp., a Ciliate from the Hypersaline Water of a Solar Saltern

A new ciliate, Trimyema koreanum n. sp., isolated from hypersaline water (salinity of 293 parts per thousand) from a solar saltern in Korea, was investigated using live observation, protargol impregnation, and gene sequencing. Trimyema koreanum is about 30 x 13 mu m in vivo, has usually 23 longitudinal ciliary rows forming two distinct ciliary girdles visible both in vivo and in protargol impregnation. A third indistinct ciliary girdle as well as a girdle of mucocysts is distinguishable only in impregnated cells. We suggest T. koreanum as a new species, differing from the most similar species, T. marinum, by the presence of two distinct ciliary girdles (T. marinum usually has six ciliary girdles clearly visible in living cells and three anterior spirals that encircle the cell completely). Although the number of known 18S rRNA sequences in the genus Trimyema was limited, the Trimyema group including T. koreanum forms a strong clade. The phylogenetic position confirms that the isolate belongs to the genus Trimyema and is different from previously sequenced species. Trimyema koreanum is able to consume both prokaryotes and small eukaryotes (specifically, the alga Dunaliella sp.).

Kiitricha minuta n. Sp., a peculiar hypotrichous ciliate (Ciliophora, Spirotrichea) from the Yellow Sea

The morphology and infraciliature of a new ciliate, Kiitricha minuta n. sp., isolated from the Yellow Sea, were investigated using live observation and protargol impregnation. Kiitricha minuta represents a third member of the rarely known order Kiitrichida. It is unique in the subclass Hypotrichia in having many rows of small uniform cirri along the right side of the body and the dorsal kineties composed of dikinetids, most of which bear two cilia. Kiitricha minuta n. sp. is ovoid and measures about 60 x 45 mu m in vivo. It has a huge buccal cavity occupying about 80% of the body length, numerous body extrusomes, one macronucleus and two micronuclei, 27-27 adoral membranelles, 9-12 frontoventral cirral rows, a submarginal row of 7-9 cirri, 6 or 7 transverse cirri, and roughly 7-9 dorsal kineties. This new species differs distinctly from its only congener Kiitricha marina by its smaller size (60 mu m vs. 80-150 mu m), the presence of body extrusomes (vs. absent), the different macronuclear pattern (one vs. two nodules), and the lower number of frontoventral cirral rows (9-12 vs. 21-26), which terminate at the anterior two-thirds of body (vs. extend to the posterior). The new term "submarginal cirral row" is introduced to distinguish from the marginal cirral row in typical hypotrichs sensu lato. Based on our new observations and the literature, an improved diagnosis for the genus Kiitricha is provided and its phylogenetic importance is discussed.

Stress corrosion cracking of AISI 321 stainless steel in acidic chloride solution

The stress corrosion cracking (SCC) of LambdaISI 321 stainless steel in acidic chloride solution was studied by slow strain rate (SSR) technique and fracture mechanics method. The fractured surface was characterized by cleavage fracture. In order to clarify the SCC mechanism, the effects of inhibitor KI on SCC behaviour were also included in this paper. A study showed that the inhibition effects of KI on SCC were mainly attributed to the anodic reaction of the corrosion process. The results of strain distribution in front of the crack tip of the fatigue pre-cracked plate specimens in air, in the blank solution (acidic chloride solution without inhibitor KI) and in the solution added with KI measured by speckle interferometry (SPI) support the unified mechanism of SCC and corrosion fatigue cracking (CFC).

Pure mechanical wear loss measurement in corrosive wear

The method for the measurement of the pure mechanical wear loss for 321 stainless steel, 1045 steel and pure iron in the study of the synergy between corrosion and wear was studied, The methods studied included the measurement in distilled water, by cathodic protection and by adding inhibitor KI, and all were compared with the wear loss in air. The experiment showed that the pure mechanical wear losses and friction coefficients obtained by the three methods were close to each other and can be used to calculate the various wear components in the study of the interaction of corrosion and wear, but the measurements in distilled water for pure iron and 1045 steel are not recommended due to their corrosion.

青海海北地区高山嵩草草甸植物群落生物量动态及能量分配

对青海海北地区高山草甸主要植物群落小嵩草(K obresia pygmaea) 草甸、矮嵩草(K. humilis) 草甸、藏嵩草(K. tibetica) 沼泽化草甸地上生物量动态和能量分配的研究结果表明, 不同植物群落年地上净生产量及其年际动态和主要植物类群生物量季节动态具明显的差异, 其生物量季节动态可由如下模型表示: W i = Ki/(1 + exp (A i - B it) ) 　　植物群落地上、地下生物量的垂直分布呈典型的金字塔和倒金字塔模式。小嵩草草甸、矮嵩草草甸和藏嵩草沼泽化草甸的地上净生产量依次为368.4g·m – 2·a- 1、418.5 g·m – 2·a- 1和518.4 g·m – 2·a- 1, 所固定的太阳能值依次为6655.16kJ·m – 2·a- 1、7610.09 kJ·m – 2·a- 1、9488.77 kJ·m – 2·a- 1。光能利用率分别为0.1097%、0.1256%、0.1568%。

双机械臂协调系统的一类最优轨迹规划方法

中国黄土的磁组构特征及其古风向指示意义

The transportation and deposition of eolian materials of Chinese loess is correlated and effected by the monsoon from the mid-high latitude. Therefore study of the winter monsoon evolution can help us to understand the dynamic mechanism to climate changes in the east-Asian areas. The anisotropy of magnetic susceptibility (AMS) measurements have been carried out on the samples from the last 250ka wind -blown loess-paleosol sequences at Baicaoyuan and Luochuan. And the main conclusions are following:The magnetic foliation is almost horizontal of the two sections. AMS canthus be represented by an oblate ellipsoid with average K3 perpendicular to thebedding plane and Ki within the bedding plane. It has also shown that the ^-factor isless than 0.5 of the majority of samples. So the two sections are normal magneticfabric for sediments.The degree of anisotropy always shows a strong correlation with the foliationrather than with lineation, therefore the anisotropy is controlled by the foliation.Furthermore the foliation is nearly less than 1.02 and shows the typical wind-blownsediments anisotropy.The intensity of winter monsoon, grain size of the eolian inputs, the foliationand the degree of anisotropy are somewhat inter-related. Generally, the higherintensity of the winter monsoon will carry coarser-grained eolian material, therebyresulting in a larger foliation during deposition. Also the post-depositional compactioncontributes to the anisotropy.The AMS features between loess and paleosol are somewhat different. Wefound that the F, P values of paleosol are lower than that of its parent loess respectively. Moreover, the difference does also exists between the two sections. The anisotropy of Baicaoyuan is more significant than Luochuan section, which maybe related with the location and the intensity of the post-deposition reworks.5. We note that the declination of the long axis is NWW in Baicaoyuan section and the observed NWW direction of the winter monsoon winds based on AMS is consistent with the view that the winter monsoons prevail along the NW-SE direction. But at the Luochuan section, because of the strong affection of the post-deposition reworks, the direction of the long axis is nearly random in the foliation and hardly recognizes the paleowind direction since the last two interglacials.Correlation between the two loess-paleosol sequences implies that it is available in arid or semi-arid areas to take AMS to recognize the paleowind directions on the Loess Plateau.