Influence of Indenter Tip Roundness on Hardness Behavior in Nanoindentation

In this paper. the effect of indenter tip roundness on hardness behavior for two typical elastic perfectly plastic materials is studied by means of finite element simulation. A rigid conical indenter of semi apex angle 70.3 degrees fitted smoothly with a spherical tip is employed. It is shown that as the indentation depth increases hardness first rises from zero, reaches a maximum and then decreases slowly approaching asymptotically the limiting value equal to that due to a conical indenter of ideally sharp tip. The range within which hardness varies appreciably is comparable to the radius of the indenter tip. The difference between the maximum value and the limiting value depends on the yield stress over the Young's modulus ratio. The smaller this ratio the greater the difference is. Numerical simulation also provides an opportunity for checking the accuracy and limitations of the widely used Oliver-Pharr method.

Nanoindentation of thin-film-substrate system: Determination of film hardness and Young's modulus

In the present paper, the hardness and Young's modulus of film-substrate systems are determined by means of nanoindentation experiments and modified models. Aluminum film and two kinds of substrates; i.e. glass and silicon, are studied. Nanoindentation XP II and continuous stiffness mode are used during the experiments. In order to avoid the influence of the Oliver and Pharr method used in the experiments, the experiment data are analyzed with the constant Young's modulus assumption and the equal hardness assumption. The volume fraction model (CZ model) proposed by Fabes et al. (1992) is used and modified to analyze the measured hardness. The method proposed by Doerner and Nix (DN formula) (1986) is modified to analyze the measured Young's modulus. Two kinds of modified empirical formula are used to predict the present experiment results and those in the literature, which include the results of two kinds of systems, i.e., a soft film on a hard substrate and a hard film on a soft substrate. In the modified CZ model, the indentation influence angle, phi, is considered as a relevant physical parameter, which embodies the effects of the indenter tip radius, pile-up or sink-in phenomena and deformation of film and substrate.

Simple phenomenological determination of contact stiffness and elastic modulus of Ce-based bulk metallic glasses through nanoindentation

The viscoelastic deformation of Ce-based bulk metallic glasses (BMGs) with low glass transition temperature is investigated at room temperature. Contact stiffness and elastic modulus of Ce-based BMGs cannot be derived using the conventional Oliver-Pharr method [W. C. Oliver and G. M. Pharr, J. Mater. Res. 7, 1564 (1992)]. The present work shows that the time dependent displacement of unloading segments can be described well by a generalized Kelvin model. Thus, a modified Oliver-Pharr method is proposed to evaluate the contact stiffness and elastic modulus, which does, in fact, reproduce the values obtained via uniaxial compression tests. (c) 2007 American Institute of Physics.

宏观深度测量压入仪器的研制

基于深度测量压入方法,以材料试验机Instron 5848 Microtester作为加载平台,外接高分辨力位移传感器,设计专用夹具,开发出该材料试验机的宏观压入功能.研究发现:对于机架柔度,无需再进行修正;对于压针接触面积,可用相关的方法计算.采用Oliver-Pharr方法处理测试数据,可获得材料的硬度和弹性模量.为了验证试验的可靠性,选用5种典型金属材料,将宏观压入测试结果与MTS Nano Indenter(R) XP测试结果进行对比,二者基本一致,其分散性均在10%以内.显示了开发传统材料试验机宏观压入测试功能的可行性

纳米压痕仪接触投影面积标定方法的研究

基于Oliver与Pharr方法的纳米压痕实验以其简单方便获得广泛的应用,但众多因素对压痕实验结果的影响范围并无明确的结论.其中压痕接触面积的确定是一个重要环节,该因素对实验结果,特别是小深度下的实验结果具有重要影响.仔细分析了Oliver与Pharr方法并进行了几种材料的纳米压痕实验,针对该方法在接触深度确定、不同深度范围下方法的适用性进行了说明.分析结果表明,对所有的材料使用统一的面积公式,只有在大压痕深度时才是适用的,而在小压痕深度时可能带来较大的误差.因此,应慎重使用由Oliver与Pharr方法得到的小压痕深度的硬度数据.

Relationships between Initial Unloading Slope, Contact Depth, and Mechanical Properties for Spherical Indentation in Linear Viscoelastic Solids

Using analytical and finite element modeling, we examine the relationships between initial unloading slope, contact depth, and mechanical properties for spherical indentation in viscoelastic solids with either displacement or load as the independent variable. We then investigate whether the Oliver-Pharr method for determining the contact depth and contact radius, originally proposed for indentation in elastic and elastic-plastic solids, is applicable to spherical indentation in viscoelastic solids. Finally, the analytical and numerical results are used to answer questions raised in recent literature about measuring viscoelastic properties from instrumented spherical indentation experiments.

微尺度压痕实验的数值模拟及相关问题研究

目前国际上占主导地位的纳米压痕技术是由Oliver与Pharr提出并发展,目前的纳米压痕可以给出整个加、卸载过程的载荷—位移曲线以及硬度与弹性模量随压痕深度变化的曲线,从而提供了丰富的、比较精确的信息,为利用它探索材料比较完整的力学特性提供了可能.为达到该目的,就必须对压痕实验的加、卸过程进行较为深入的研究.作为主要的研究工具,有限元方法模拟微压痕过程在探讨通过实验数据得到更多、更准确的材料表层力学性能参数以及解释实验现象等方面发挥着重要作用.基于计算机速度与容量的原因,较早进行微压痕过程有限元模拟的BhattacharyaandNix、LaursenandSino都使用圆锥压头模拟维氏显微硬度标准正四棱锥Vicker压头与纳米压痕仪标准正三棱锥Berkovich压头,因为圆锥压头具有旋转对称性,可用二维旋转对称单元(二维实体单元)进行计算从而降低计算规模.即便如此,以当时大型计算机的水平,对规模为400~2000个四节点矩形单元的有限元模型进行一次完整的加、卸载过程也需要1~2天.到目前为止,微尺度压痕实验的数值模拟沿用二维模型.事实上,由于加工工艺的限制,微尺度压痕仪的压头如Berkovich与Vicker压头均不个旋转对称性;就微观尺度而言,实际的表层材料都是非均匀的.这些特征均不能由二维模拟体现,所以该文首先建立三维有限元模型,模拟带滑动接触的微尺度压痕加、卸载过程.在此基础上重点讨论了压头几何效应的问题,如二维模拟与三维模拟的关系、显微硬度与纳米的压痕硬度的关系、不同压头下材料的应力应变场、压痕间距与压痕边界的效应等,最后针对微尺度压痕实验中出现的压痕硬度随压痕深度减小而升高的现象,讨论了影响不同压痕深度硬度值的因素.

一种ICF用新型可阵列反射镜架结构

运用并联机构原理设计了一种新型惯性约束聚变（Inetial Confinement Fusion, ICF）用可阵列反射镜架结构,并用坐标变换方法分析了机构的调整正交性与旋转轴正交性之间的关系.装置的实际测试结果表明调整正交性与分析结果一致,并且反射镜架的稳定性以及调节准确度均能符合ICF装置的使用要求.

沿阶草族的染色体研究及系统学问题的探讨

本论文对沿阶草族Ophiopogoneae(Endl.)Kunth的研究历史作了回顾，从染色体、形态学和解剖学角度对此族作了研究，并作了数值分类和分支 系统学分析的尝试，在此基础上探讨了这个族的系统学问题． 1)本论文对此族三属37种123居群的染色体数目、基数及核型不对称性作了研究，其中19种的染色体为首次报道．它们是：P．macrostegiaHance， P.yunnanensis Wang et Tang，P.ophiopogonoides Wang et Tang,O. sarmentosus Wang et Dai,O.tienensis Wang et Tang, O.sylvicola Wang et Tang, O.fooningensis Wang et Dai, O.mairei L6vl.，O.szechuanensis Wang et Tang, O.angustiatus (Wang et Tang) S.C.Chen, O.amblyphyllus Wang et Dai,O.clavatus Wright ex Oliver,O.clivioidesD.M.Zhang et Hong, O.longiscaposus D.M.Zhang et Hong,O.umbraticola Hance,O.fuiD.M.Zhang ntHong,O.zingiberaceus Wang et Dai,O.gangxiensisd.M.Zhang et Hong,O. lo fouense L6vl. 2)在此族中首次报道了2n = 2x = 34的异基数二倍体，同时在O.umbraticola，O.japonicus,O.cLarkei中报道了2n=68的异基数二倍体，过核型和减数分裂等证明异基数是在二倍体水平上形成，并发展成倍性系列的． 3)在此族中首次报道了B染色体的存在，已确证了两种(P.macrostegia和D.tienensis)．一种尚需进一步确证(O.Larkei)． 4)通过对随体位置的系统研究，发现在此族中随体位置具有分类价值． 5)通过对8个种内多倍体、4个多倍体种的研究，表明多倍体分布于较北、海拔较高的地方，而亚洲热带地区的种，则无多倍体，同时在具异基数种类和核型较不对称种类上亦有这种分布特征;在确定了分布的多度中心的基础上，提出喜马拉雅_横断山脉到川西、川南一带是沿阶草属和山麦冬属的近代分化中心． 6)通过染色体结构和数目几个角度的研究，表明球子草属与其他两属在。染色体水平上已发生很大分化，但其属内的分化则不表现在染色体上．其他二属内部则有基数、倍性和核型不对称方面的分化．综观此族，染色体具有由核 型对称向不对称、由二倍体向多倍体、由种内多倍体向多倍体种，由单一基数向种内异基数几个方向进化的趋势． 7)通过对此族的形态观察和分析，提出茎或根状茎分枝方式是属下分类的重要依据;认为本族植物的花序是由圆锥花序简化而来，但残留着圆锥花序特征;并提出了本族花、茎、叶、根几个方面的形态演化趋势． 8)通过对此族二属21种的子房解剖，发现三属均有半下位子房，因而认为子房半下位作为分属检索性状是不合适的．此外还观察到子房着生位置在种内亦有变异，对这种变异的意义进行了探讨． 9)通过此族三属46种2变种的数值分类处理，表明本族由球子草群和沿阶草一山麦冬群两大类群组成，山麦冬属仅是与沿阶草属一个组（葶花组）并列的分类单元，其内部分化较小，而沿阶草属则较大． 10)通过46个性状计算了山麦冬属和沿阶草属共6个广布的“群内总体相 似度”(IOS)，表明山麦冬属3个种种内个体之间、种间个体之间的分化很小，且可能有杂交现象，结合染色体资料和分布特征，认为这个属的发生是个相当晚近的事件． 11)本文从形态和染色体角度，认为沿阶草族是一个自然类群;由分支系 统学分析表明，此族由二个单系类群（球子草属和沿阶草属）组成，沿阶草属含两个单系的组，其中各含3个系，山麦冬属为其中一个系．这一结果与数值 分类结果和染色体资料相符． 12)为避免单一分类方法可能导致的不合理结果，本文以自拟的一种综合分类方法，把谱系、进化、分化诸因素均予考虑，得出一个三维图象，以图象 上相对等径的球作为分类依据，得出的结果与分支系统学和数值分类结果基本一致．因此，山麦冬属作为与沿阶草属等阶的分类地位，应予重新考虑． 13）本文最后对这个族的全面修订提出几点建议. 14）此外，本文还描述了沿阶草属4个新种.

人与大猩猩、黑猩猩和猩猩亲缘关系的探讨

有关人猿超科的系统发育仍然存在争议。争论焦点在人与大猩猩和黑猩猩哪个关系更近一点。酪氨酸酶是黑色素合成中的关键酶，酪氨酸酶基因的突变将导致白化病。测定了人猿超科中大猩猩、黑猩猩、猩猩和长臂猿酪氨酸酶基因全部5个外显子的DNA序列。结合已发表人的序列，用简约法构建了基因树。结果表明，人与大猩猩的关系比黑猩猩要近一些。

Genome 10K: A Proposal to Obtain Whole-Genome Sequence for 10 000 Vertebrate Species

The human genome project has been recently complemented by whole-genome assessment sequence of 32 mammals and 24 nonmammalian vertebrate species suitable for comparative genomic analyses. Here we anticipate a precipitous drop in costs and increase in sequ

The sequence and de novo assembly of the giant panda genome

Using next-generation sequencing technology alone, we have successfully generated and assembled a draft sequence of the giant panda genome. The assembled contigs (2.25 gigabases (Gb)) cover approximately 94% of the whole genome, and the remaining gaps (0.05 Gb) seem to contain carnivore-specific repeats and tandem repeats. Comparisons with the dog and human showed that the panda genome has a lower divergence rate. The assessment of panda genes potentially underlying some of its unique traits indicated that its bamboo diet might be more dependent on its gut microbiome than its own genetic composition. We also identified more than 2.7 million heterozygous single nucleotide polymorphisms in the diploid genome. Our data and analyses provide a foundation for promoting mammalian genetic research, and demonstrate the feasibility for using next-generation sequencing technologies for accurate, cost-effective and rapid de novo assembly of large eukaryotic genomes.

Stress within the postseizure time window inhibits seizure recurrence

Recurrence is a key characteristic in the development of epilepsy. It remains unclear whether seizure recurrence is sensitive to postseizure stress. Here, tonic-clonic seizures were induced with a convulsive dose of pentylenetetrazole (PTZ), and acute seizure recurrence was evoked with a subconvulsive dose of the drug. We found that stress inhibited seizure recurrence when applied 30 minutes or 2 hours, but not 4 hours, after the tonic-clonic seizure. The time-dependent anti-recurrence effect of stress was mimicked by the stress hormone corticosterone and blocked by co-administration of mineralocorticoid and glucocorticoid receptor antagonists. Furthermore, in a PTZ-induced epileptic kindling model, corticosterone administered 30 minutes after each seizure decreased the extent of seizures both during the kindling establishment and in the following challenge test. These results provide novel insights into both the mechanisms of and therapeutic strategies for epilepsy. (C) 2010 Elsevier Inc. All rights reserved.

Molecular phylogeography and population structure of a mid-elevation montane frog Leptobrachium ailaonicum in a fragmented habitat of southwest China

Leptobrachium ailaonicum is a vulnerable anuran restricted to a patchy distribution associated with small mountain streams surrounded by forested slopes at mid-elevations (approximately 2000-2600 m) in the subtropical Mount Wuliang and Mount Ailao ranges in southwest China (Yunnan Province) and northern Vietnam. Given high habitat specificity and lack of suitable habitat in lower elevations between these ranges, we hypothesized limited gene flow between populations throughout its range. We used two mitochondrial genes to construct a phylogeographic pattern within this species in order to test our hypothesis. We also examined whether this phylogeographic pattern is a response to past geological events and/or climatic oscillations. A total of 1989 base pairs were obtained from 81 individuals of nine populations yielding 51 unique haplotypes. Both Bayesian and maximum parsimony phylogenetic analyses revealed four deeply divergent and reciprocally monophyletic mtDNA lineages that approximately correspond to four geographical regions separated by deep river valleys. These results suggest a long history of allopatric separation by vicariance. The distinct geographic distributions of four major clades and the estimated divergence time suggest spatial and temporal separations that coincide with climatic and paleogeographic changes following the orogeny and uplift of Mount Ailao during the late Miocene to mid Pliocene in southwest China. At the southern distribution, the presence of two sympatric yet differentiated clades in two areas are interpreted as a result of secondary contact between previously allopatric populations during cooler Pleistocene glacial cycles. Analysis of molecular variance indicates that most of the observed genetic variation occurs among the four regions implying long-term interruption of maternal gene flow, suggesting that L ailaonicum may represent more than one distinct species and should at least be separated into four management units corresponding to these four geographic lineages for conservation. (C) 2009 Elsevier Inc. All rights reserved.

Nuclear matrix of the most primitive eukaryote Archezoa

Accumulating evidence suggests that unicellular Archezoa are the most primitive eukaryotes and their nuclei are of significance to the study of evolution of the eukaryotic nucleus. Nuclear matrix is an ubiquitous important structure of eukaryotic nucleus; its evolution is certainly one of the most important parts of the evolution of nucleus. To study the evolution of nuclear matrix, nuclear matrices of Archezoa are investigated. Giardia lamblia cells are extracted sequentially. Both embedment-free section EM and whole mount cell EM of the extracted cells show that, like higher eukaryotes, this species has a residual nuclear matrix in its nucleus and rich intermediate filaments in its cytoplasm, and the two networks connect with each other to form a united network. But its nuclear matrix does not have nucleolar matrix and its lamina is not as typical as that of higher eukaryotes; Western blotting shows that lamina of Giardia and two other Archezoa Entamoeba invadens and Trichomonas vaginali all contain only one polypeptide each which reacts with a mammalia anti-lamin polyclonal serum and is similar to lamin B (67 ku) of mammlia in molecular weight. According to the results and references, it is suggested that nuclear matrix is an early acquisition of the eukaryotic nucleus, and it and the "eukaryotic chromatin" as a whole must have originated very early in the process of evolution of eukaryotic cell, and their origin should be an important prerequisite of the origin of eukaryotic nucleus; in the iamin (gene) family, B-type lamins (gene) should be the ancestral type and that A-type lamins (gene) might derive therefrom.