Near-Space Wide-Swath Radar Imaging With Multiaperture Antenna

Near-space, defined as the altitude region between 20 and 100 km, offers many capabilities that are not accessible for low Earth-orbit (LEO) satellites or airplanes because it is above storm and not constrained by orbital mechanics and high fuel consumption. Hence, a high flying speed can be obtained for the maneuvering vehicles operating in near-space. This offers a promising solution to simultaneous high-resolution and wide-swath synthetic aperture radar (SAR) imaging. As such, one near-space wide-swath SAR imaging technique is presented in this letter. The system configuration, signal model, and imaging scheme are described. An example near-space SAR system is designed, and its imaging performance is analyzed. Simulation results show that near-space maneuvering vehicle SAR indeed seems to be a promising solution to wide-swath SAR imaging.

总线桥:概念、方法和实现

在基于不同总线标准的个人计算机、工程工作站以及一些工业控制机间建立高速的并行通信通道,将它们构成多机系统,能够以较小的代价获得增强的系统特性.本文引入了一种在系统总线间提供并行数据通道的异种总线互连底板——总线桥的概念,讨论了它的结构和工作原理,提出了其实现方案,并着重描述了为总线桥定义的双向并行通讯协议 BBP(Bus Bridge Prtocol)

PASSIM卷接机组新型电控系统的设计与实现

PASSIM卷接机组原控制系统采用电路板进行逻辑控制,抗干扰性能差,故障率高,造成生产效率降低、原材料消耗增大、维修工作繁重等。为此,设计了一套新型卷接机组电气控制系统。该系统采用PLC进行过程控制,以工控机为上位机完成人机通信,采用交流伺服驱动,并通过高速信号处理专用系统完成重量检测控制及烟支质量检测功能;利用PROFIBUS、CAN及MPI多种总线方式完成各单元间的通讯,实现信号和数据间的传递和共享。改进后的PASSIM机组运行稳定可靠,采样速度快,实时性强,且维修方便。机组的有效作业率由85%左右提高到90%以上,降低了卷烟纸和烟丝等原材料的消耗。

浑善达克沙地全新世气候变化与风沙活动—夏日淖湖泊沉积记录

Atmospheric dust as an important factor for climate feedbacks is mainly derived from and drove by the aeolian activities of the semi-arid regions in Asia. Therefore, reconstructing the history of aeolian activities in this region has a great significance in understanding the dynamics of past and future climate changes. This paper made a systematical sedimentology, geochemisty and high-resolution chronology analysis on the sediments from the Xiarinao Lake, which located in Hunshandake Desert, Inner Mongolia, and compared with the meteorological records for identifying the indicator of aeolian activities and climate changes. Based on above work, the evolution history of the aeolian activities and climate changes since 11,000 a BP was reconstructed and the dynamics of the aeolian activities and climate changes in the Hunshandake Desert was discussed. The indicator of aeolian activities was established through the comparison of the clastic and chemical records with the meteorological registers in recent 50 years: 1. The sediments of Xiarinao Lake are mainly derived from eaolian clastic materials and composed of two major components: one is the sand fraction (<4 ) similar to the composition of sand dunes, the other is the silt fraction (>4 ) similar to the atmospheric dust. The sand content and the median grain size, particularly the sand content, show a close association with the intensity of wind, indicating that the particle-size composition of the sediments reflect the variations of the aeolian activities. 2. The proportion of soluble salts relative to the total carbonates in the sediments was correlated to the arid degree registered in meteorological records, suggesting that arid degree might be associated with changes of wind speed and the relative proportion of soluble salts to the total carbonate could be used as the indicator of aridity. 3. The δ18O of authigenic calcite in the Xiarinao Lake show a well correlation with both the atmosphere precipitation and variation of the moisture indicated by the concentrations of soluble salts, suggesting that δ18O of anthigenic calcite is a reliable indicator of humidity. Based on above studies, the evolution history of the aeolian activities and climate changes since 11,000 a BP was reconstructed. At the same time, their association and underlying dynamics was discussed: 1. The evolution history of the eaolian activity was reconstructed by the sand content and median grain size. The result showed that aeolian activities had experienced several different climate periods in the Holocene: the aeolian activities fluctuated with a 500-year cycles during the interval from 10,900 to 8200 a BP; no significant aeolian activities had been developed from 8200 to 6300 a BP; during the interval of 6300 to 2600 a BP, sand content and media grain size had increased gradually, the sand content increased from about 5% to 25%, indicating the intensity of aeolian activity increased in the Hunshandake Desert; since 2600 a BP, intensity of aeolian activity has become stronger and activated the sand dunes. 2. The relative arid degree indicated by the proportion of soluble salts relative to the total carbonate show that both the wind speed and dry degree had being increased since 11,000 a BP. During the interval of 10900 to 6300 a BP, no detectable soluble salt was found in the sediments, indicating the humidity condition; the proportion increased to 20% from 6300 to 4200 a BP, showing the climate became drier; the little change of proportion (20%) suggest that the climate was relative stable during the interval of 4200 to 2600 a BP; after 2600 a BP, the proportion increased, showing the climate became further dry. 3. The δ18O evolution of the lake water was established through analysis of authigenetic calcite δ18O for revealing the variations of relative effective humidity in the Hunshandake Desert. δ18O maintained around -6 ‰ during the interval of 10900 to 8200 a BP, showing the climate was a little dry relative to that of the whole Holocnene; in the period of 8200 to 6300 a BP, δ18O had the most negative values, indicating that it was the most humid interval in Holocene; from 6300 to 4200 a BP, δ18O increased from about -7.5 ‰ to about -3 ‰ gradually, suggesting increased aridity; since 4200 a BP, the climate has become stable and dry. On the whole, the records in this study show that the variation of the relative humidity and aridity is consistent with that of summer monsoon in the Hunshandake Desert. The relationships among the grain size, soluble salts relative content, and the authigenic calcite δ18O indicate aeolian activities is controlled by the aridity in the studied area, and the increased aeolian activities is closely associated with the temperature changes under the relative dry condition. The high wind speed under the low temperature leads to the increased aeolian activity, and the temperature change associated with the aeolian activities might be related with the perturbations of the Siberian High Pressure.

Small-signal and large-signal performance test of high-speed optoelectronics devices

This paper presents measurement methods for determining the reflection coefficients and frequency responses of semiconductor laser diodes, photodiodes, and EA modulator chips. A novel method for determining the intrinsic frequency responses of laser diodes is also proposed, and applications of the developed measurement methods are discussed. We demonstrate the compensation of bonding wire on the capacitances of both the submount and the laser diode, and present a method for estimating the potential modulation bandwidth of TO packaging technique. Initial study on removing the effects of test fixture on large-signal performances of optoelectronic devices at high data rate is also given.

Investigation of High-Speed Combustible Gas Ignited by a Hot Gas Jet Produced in the Shock Tube

The high-speed combustible gas ignited by a hot gas jet, which is induced by shock focusing, was experimentally investigated. By use of the separation mode of shock tube, the test section of a single shock tube is split into two parts, which provide the high-speed flow of combustible gas and pilot flame of hot gas jet, respectively. In the interface of two parts of test sections the flame of jet was formed and spread to the high-speed combustible gas. Two kinds of the ignitions, 3-D “line-flame ignition” and 2-D “plane-flame ignition”, were investigated. In the condition of 3-D “lineflame ignition” of combustion, thicker hot gas jet than pure air jet, was observed in schlieren photos. In the condition of 2-D “plane-flame ignition” of combustion, the delay time of ignition and the angle of flame front in schlieren photos were measured, from which the velocity of flame propagation in the high-speed combustible gas is estimated in the range of 30–90 m/s and the delay time of ignition is estimated in the range of 0.12–0.29 ms.

Investigation of High-Speed Combustible Gas Ignited by a Hot Gas Jet Produced in the Shock Tube

The high-speed combustible gas ignited by a hot gas jet, which is induced by shock focusing, was experimentally investigated. By use of the separation mode of shock tube, the test section of a single shock tube is split into two parts, which provide the high-speed flow of combustible gas and pilot flame of hot gas jet, respectively. In the interface of two parts of test sections the flame of jet was formed and spread to the high-speed combustible gas. Two kinds of the ignitions, 3-D "line-flame ignition" and 2-D "plane-flame ignition", were investigated. In the condition of 3-D "line-flame ignition" of combustion, thicker hot gas jet than pure air jet, was observed in schlieren photos. In the condition of 2-D "plane-flame ignition" of combustion, the delay time of ignition and the angle of flame front in schlieren photos were measured, from which the velocity of flame propagation in the high-speed combustible gas is estimated in the range of 30-90m/s and the delay time of ignition is estimated in the range of 0.12-0.29ms.

Characterization of parasitics in TO-packaged high-speed laser modules

An elaborate analysis of the parasitic network of high-speed through-hole packaging (TO)-type laser modules is presented using a small-signal equivalent circuit model. The intrinsic laser diode is obtained using the optical modulation technique, and is embedded into the model as a separate component. Three step-by-step measurements are made for determining the packaging parasitic network, including the test fixture, TO header, submount, bonding wire, and parasitics of the laser chip. A good agreement between simulated and measured results confirms the validation and accuracy of the characterization procedures. Furthermore, several key parasitic elements are found based on the simulation of the high-frequency responses of the packaged devices. It is expected that the 3-dB bandwidth of 12 GHz or more of the low-cost TO packaged laser module may be achieved using the proposed optimization method.

An analysis of the performance of a new high-speed single-way analog switch

This paper introduces a new highspeed single-way analog switch which has both highspeed high-resolution mono-direction analog transmission gate function and high-speed digital logic gate function with normal bipolar technology. The analysis of static and transient switching performances as an analog transmission gate is emphasized in the paper. In order to reduce the plug-in effect on high-speed high-resolution systems, an optimum design scheme is also given. This scheme is to achieve accelerated dynamic response with very low bias power dissipation. The analysis of PSPICE simulation as well as the circuit test results confirms the feasibility of the scheme. Now, the circuit has been applied effectively to the designs of novel highspeed A/D and D/A converters.

An efficient combination of supercritical fluid extraction and high-speed counter-current chromatography to extract and purify homoisoflavonoids from Ophiopogon japonicus (Thunb.) Ker-Gawler

Supercritical fluid extraction (SFE) was used to extract homoisoflavonoids from Ophiopogon japonicus (Thunb.) Ker-Gawler. The optimization of parameters was carried out using an orthogonal test L-9 (3)(4) including pressure, temperature, dynamic extraction time and the amount of modifier. The process was then scaled up by 100 times with a preparative SFE system under the optimized conditions of 25 MPa, 55 degrees C, 4.0 h and 25% methanol as a modifier. Then crude extracts were separated and purified by high-speed counter-current chromatography (HSCCC) with a two-phase solvent system composed of n-hexane/ethyl acetate/methanol/ACN/water (1.8:1.0:1.0:1.2:1.0 v/v). There three homoisoflavonoidal compounds including methylophiopogonanone A 6-aldehydo-isoophiopogonone A, and 6-formyl-isoophiopogonanone A, were successfully isolated and purified in one step. The collected fractions were analyzed by HPLC. In each operation, 140 mg crude extracts was separated and yielded 15.3 mg of methylophiopogonanone A (96.9% purity), 4.1 mg of 6-aldehydo-isoophiopogonone A (98.3% purity) and 13.5 mg of 6-formyl-isoophiopogonanone A (97.3% purity) respectively. The chemical structure of the three homoisoflavonoids are identified by means of ESI-MS and NMR analysis.

Evaluation of the Cumulative Formation of High-Speed Liquid Jets

This paper describes the generation of pulsed, high-speed liquid jets using the cumulation method. This work mainly includes (1) the design of the nozzle assembly, (2) the measurement of the jet velocity and (3) flow visualization of the injection sequences. The cumulation method can be briefly described as the liquid being accelerated first by the impact of a moving projectile and then further after it enters a converging section. The experimental results show that the cumulation method is useful in obtaining a liquid jet with high velocity. The flow visualization shows the roles of the Rayleigh-Taylor and Kelvin-Helmholtz instabilities in the breakup of the liquid depend on the jet diameter and the downstream distance. When the liquid jet front is far downstream from the nozzle exit, the jet is decelerated by air drag. Meanwhile, large coherent vortex structures are formed surrounding the jet. The liquid will break up totally by the action of these vortices. Experimental results showing the effect of the liquid volume on the jet velocity are also included in this paper. Finally, a method for measuring the jet velocity by cutting two carbon rods is examined.

Shock Tube Studies on the Nonequlibrium Electron Affinity Kinetics of Fluorine Atom at High Temperatures

To study electron affinity kinetics, a shock tube method was applied, in which the test gas was ionized by a reflected shock wave and subsequently quenched by a strong rarefaction wave. As the quenching speed of 106 K/s was reached, a nonequilibrium ionization-recombination process occurred, which was dominated by ion recombination with electrons. A Langmuir electrostatic probe was used to monitor variation in the ion number density at the reflection shock region. The working state of the probe was analyzed...

Experimental Study on Hydrodynamic Behaviors of High-Speed Gas Jets in Still Water

The present paper describes experimental investigation on the flow pattern and hydrodynamic effect of underwater gas jets from supersonic and sonic nozzles operated in correct- and imperfect expansion conditions. The flow visualizations show that jetting is the flow regime for the submerged gas injection at a high speed in the parameter range under consideration. The obtained results indicate that high-speed gas jets in still water induce large pressure pulsations upstream of the nozzle exit and the presence of shock-cell structure in the over- and under-expanded jets leads to an increase in the intensity of the jet-induced hydrodynamic pressure.

The Head-On Colliding Process Of Binary Liquid Droplets At Low Velocity: High-Speed Photography Experiments And Modeling

The experimental and theoretical studies are reported in this paper for the head-on collisions of a liquid droplet with another of the same fluid resting on a solid substrate. The droplet on the hydrophobic polydimethylsiloxane (PDMS) substrate remains in a shape of an approximately spherical segment and is isometric to an incoming droplet. The colliding process of the binary droplets was recorded with high-speed photography. Head-on collisions saw four different types of response in our experiments: complete rebound, coalescence, partial rebound With conglutination, and coalescence accompanied by conglutination. For a complete rebound, both droplets exhibited remarkable elasticity and the contact time of the two colliding droplets was found to be in the range of 10-20 ms. With both droplets approximately considered as elastic bodies, Hertz contact theory was introduced to estimate the contact time for the complete rebound case. The estimated result Was found to be on the same order of magnitude as the experimental data, which indicates that the present model is reasonable. (C) 2008 Elsevier Inc. All rights reserved.

Investigation Of Mode Ii Crack Growth Following A Very High Speed Impact

A recoverable plate impact testing technology has been developed for studying fracture mechanisms of mode II crack. With this technology, a single duration stress pulse with submicrosecond duration and high loading rates, up to 10(8) MPam(1/2)s(-1), can be produced. Dynamic failure tests of Hard-C 60# steel were carried out under asymmetrical impacting conditions with short stress-pulse loading. Experimental results show that the nucleation and growth of several microcracks ahead of the crack tip, and the interactions between them, induce unsteady crack growth. Failure mode transitions during crack growth, both from mode I crack to mode II and from brittle to ductile fracture, were observed. Based on experimental observations, a discontinuous crack growth model was established. Analysis of the crack growth mechanisms using our model shows that the shear crack extension is unsteady when the extending speed is between the Rayleigh wave speed c(R) and the shear wave speed c(S). However, when the crack advancing speed is beyond c(S), the crack grows at a steady intersonic speed approaching root 2c(S). It also shows that the transient mechanisms, such as nucleation, growth, interaction and coalescence among microcracks, make the main crack speed jump from subsonic to intersonic and the steady growth of all the subcracks causes the main crack to grow at a stable intersonic speed.