黄骅坳陷港西开发区河流相储层构型与剩余油分布模式研究

In the production tail of oilfield, water-cut is very high in thick channel sand oil reservoir, but recovery efficiency is relative low, and recoverable remaining oil reserves is more abundant, so these reserves is potential target of additional development. The remaining oil generally distributed with accumulation in certain areas, controlled by the reservoir architecture that mainly is the lateral accretion shale beddings in the point bar, so the study of reservoir architecture and the remaining oil distribution patterns controlled by architecture are very significant. In this paper, taking the Minghuazhen formation of Gangxi oilfield as a case, using the method of hierarchy analysis, pattern fitting and multidimensional interaction, the architecture of the meandering river reservoir is precisely anatomized, and the remaining oil distribution patterns controlled by the different hierarchy architecture are summarized, which will help to guide the additional development of oil fields. Not only is the study significant to the remaining oil forecasting, but also it is important for the theory development of reservoir geology. With the knowledge of sequence correlation and fluvial correlation model, taking many factors into account, such as combination of well and seismic data, hierarchical controlling, sedimentary facies restraint, performance verification and 3-D closure, an accurate sequence frame of the study area was established. On the basis of high-resolution stratigraphic correlation, single layer and oil sand body are correlated within this frame, and four architecture hierarchies, composite channel, single channels, point bars and lateral accretion sandbody are identified, The result indicates that Minghuazhen Formation of Gangxi oilfield are dominated by meandering river deposition, including two types of channel sandbodies, narrow band and wide band channel sandbody, and each of them has different characteristics of facies variation laterally. Based on the identification of composite channel, according to the spatial combination patterns and identified signs of single channel, combined with channel sandbody distribution and tracer material data, single channel sandbodies are identified. According to empirical formula, point-bar scales of the study area are predicted, and three identification signs are summarized, that is, positive rhythm in depositional sequence, the maximum thick sand and near close to the abandoned channel, and point bars are identified. On the basis of point bar recognition, quantitative architecture models inner point bar are ascertained, taking the lateral accretion sand body and lateral accretion shale beddings in single well as foundation, and quantitative architecture models inner point bar as guidance, and result of tracer material data as controlling, the the lateral accretion sand body and lateral accretion shale beddings are forecasted interwell, so inner architecture of point bar is anatomied. 3-D structural model, 3-D facies model and 3-D petrophysical properties models are set up, spatial distribution characteristics of sedimentary facies and petrophysical properties is reappeared. On the basis of reservoir architecture analysis and performance production data, remaining oil distribution patterns controlled by different hierarchy architecture units, stacked channel, single channel and inner architecture of point bar, are summarized, which will help to guide the additional development of oil fields.

鄂尔多斯盆地上古生界低渗透砂岩有效储层识别与预测

Sulige Gasfield, with a basically proven reserve as high as one trillion cubic meters, is one giant gas field discovered in China. The major gas -bearing layers are Upper Paleozoic strata with fluvial-lacustrine sedimentary facies. Generally, gas reservoirs in this field are characteristic by "five low" properties, namely low porosity, low permeability, low formation pressure, low productivity and low gas abundance. Reservoirs in this field also feature in a large distribution area, thin single sandbody thickness, poor reservoir physical properties, thin effective reservoir thickness, sharp horizontal and/or vertical changes in reservoir properties as well as poor connectivity between different reservoirs. Although outstanding achievements have been acquired in this field, there are still several problems in the evaluation and development of the reservoirs, such as: the relation between seismic attributes and reservoir property parameters is not exclusive, which yields more than one solution in using seismic attributes to predict reservoir parameters; the wave impedance distribution ranges of sandstone and mudstone are overlapped, means it is impossible to distinguish them through the application of post-stack impedance inversion; studies on seismic petrophysics, reservoir geophysical properties, wave reflection models and AVO features have a poor foundation, makes it difficult to recognize the specific differences between tight sandstone and gas-bearing sandstone and their distribution laws. These are the main reasons causing the low well drilling success rate and poor economic returns, which usually result in ineffective development and utilization of the field. Therefore, it is of great importance to perform studies on identification and prediction of effective reservoirs in low permeable sandstone strata. Taking the 2D and 3D multiwave-multicomponent seismic exploration block in Su6-Su5 area of Sulige field as a study area and He 8 member as target bed, analysis of the target bed sedimentary characteristics and logging data properties are performed, while criteria to identify effective reservoirs are determined. Then, techniques and technologies such as pre-stack seismic information (AVO, elastic impedance, wave-let absorption attenuation) and Gamma inversion, reservoir litological and geophysical properties prediction are used to increase the precision in identifying and predicting effective reservoirs; while P-wave and S-wave impedance, ratio of P/S wave velocities, rock elastic parameters and elastic impedance are used to perform sandstone gas-bearing property identification and gas reservoir thickness prediction. Innovative achievements are summarized as follows: 1. The study of this thesis is the first time that multiwave-multicomponent seismic data are used to identify and predict non-marine classic reservoirs in China. Through the application of multiwave-multicomponents seismic data and integration of both pre-stack and post-stack seismic data, a set of workflows and methods to perform high-precision prediction of effective reservoirs in low permeable sandstone is established systematically. 2. Four key techniques to perform effective reservoir prediction including AVO analysis, pre-stack elastic wave impedance inversion, elastic parameters inversion, and absorption attenuation analysis are developed, utilizing pre-stack seismic data to the utmost and increasing the correct rate for effective reservoir prediction to 83% from the former 67% with routine methods. 3. This thesis summarizes techniques and technologies used in the identification reservoir gas-bearing properties using multiwave-multicomponent seismic data. And for the first time, quantitative analysis on reservoir fluids such as oil, gas, and/or water are carried out, and characteristic lithology prediction techniques through the integration of pre-stack and post-stack seismic prediction techniques, common seismic inversion and rock elastic parameters inversion, as well as P-wave inversion and converted wave inversion is put forward, further increasing the correct rate of effective reservoir prediction in this area to 90%. 4. Ten seismic attribute parameters are selected in the 3D multi-wave area to perform a comprehensive evaluation on effective reservoirs using weighted-factor method. The results show that the first class effective reservoir covers an area of 10.08% of the study area, while the second and the third class reservoirs take 43.8% and 46% respectively, sharply increasing the success rate for appraisal and development wells.

渤海海域河流相油藏精细描述技术及应用研究

Aiming at the character of Bohaii Sea area and the heterogeneity of fluvial facies reservoir, litho-geophysics experiments and integrated research of geophysical technologies are carried out. To deal with practical problems in oil fields of Bohai area, such as QHD32-6, Southern BZ25-1 and NP35-2 et al., technology of reservoir description based on seismic data and reservoir geophysical methods is built. In this dissertation, three points are emphasized: ①the integration of multidiscipline; ②the application of new methods and technologies; ③the integration of quiescent and dynamic data. At last, research of geology modeling and reservoir numerical simulation based on geophysical data are integrated. There are several innovative results and conclusion in this dissertation: (1)To deal with problems in shallow sea area where seismic data is the key data, a set of technologies for fine reservoir description based on seismic data in Bohai Sea area are built. All these technologies, including technologies of stratigraphic classification, sedimentary facies identification, structure fine characterization, reservoir description, fluid recognition and integration of geological modeling& reservoir numerical simulation, play an important role in the hydrocarbon exploration and development. In the research of lithology and hydrocarbon-bearing condition, petrophysical experiment is carried out. Outdoors inspection and experiment test data are integrated in seismic forward modeling& inversion research. Through the research, the seismic reflection rules of fluid in porosity are generated. Based on all the above research, seismic data is used to classify rock association, identify sedimentary facies belts and recognition hydrocarbon-bearing condition of reservoir. In this research, the geological meaning of geophysical information is more clear and the ambiguity of geophysical information is efficiently reduced, so the reliability in hydrocarbon forecasting is improved. The methods of multi-scales are developed in microfacies research aiming at the condition of shallow sea area in Bohai Sea: ① make the transformation from seismic information to sedimentary facies reality by discriminant analysis; ②in research of planar sedimentary facies, make microfacies research on seismic scale by technologies integration of seismic multi-attributes analysis& optimization, strata slicing and seismic waveform classification; ③descript the sedimentary facies distribution on scales below seismic resolution with the method of stochastic modeling. In the research of geological modeling and reservoir numerical simulation, the way of bilateral iteration between modeling and numerical simulation is carried out in the geological model correction. This process include several steps: ①make seismic forward modeling based on the reservoir numerical simulation results and geological models; ②get trend residual of forward modeling and real seismic data; ③make dynamic correction of the model according to the above trend residual. The modern integration technology of reservoir fine description research in Bohai Sea area, which is developed in this dissertation, is successfully used in (1)the reserve volume evaluation and development research in BZ25-1 oil field and (2)the tracing while drilling research in QHD32-6 oil field. These application researches show wide application potential in hydrocarbon exploration and development research in other oil fields.

元谋盆地河湖相沉积记录的上新世印度季风转型事件

The Indian monsoon, an integral part of the global climate system, has been extensively investigated during the past decades. Most of the proxy records are derived from marine sediments and focused on time periods of the late Miocene and Pleistocene. The Pliocene represents a period when Earth’s boundary conditions underwent dramatic changes. However, variations of the Indian monsoon during the Pliocene and its forcing mechanisms have remained unclear. The Yuanmou Basin, located in the region of the Indian monsoon, provides an ideal target for understanding the Pliocene history of Indian monsoon variations. Detailed investigations on the lithostratigraphy, magnetostratigraphy and limnology of a 650-m-thick fluvio-lacustrine sedimentary sequence from the basin are carried out in the present study. The clay and clay-plus-fine-silt fractions of the sediments are referred to the midlake-facies components, and changes in the percentages of both fractions generally reflect changes in the water level of the lakes developed in the basin closely related to variations in the intensity of the Indian monsoon. Whereas the greenish-gray lacustrine mud beds represent the environment of deep-water lakes, and the frequency of individual lacustrine mud beds is considered to indicate the frequency of the deep-water lakes developed in the basin associated with the variability of the Indian monsoon. The proxy data suggest that the Indian monsoon experienced abrupt shifts at 3.53, 3.14, 2.78 and 2.42 Ma, respectivey. 1) Since 3.53 Ma, the midlake-facies components displayed a general trend of increase in the concentrations, accompanied by an increase in the sedimentation rate from an average ~10 to 25 cm ka–1. The data suggest that high stands of the lakes in the basin rose progressively, implying a gradual intensification of the Indian monsoon since that time. This shift occurred coeval with the accelerated uplift of the northern Tibetan Plateau, denoting a close link between the Indian monsoon strengthening and the Tibetan Plateau uplifting. 2) 2.78 Ma ago, the concentrations of the midlake-facies components decreased abruptly and the dominant fraction of the sediments turned to fluvial sands. The data indicate that lakes in the basin disappeared, reflecting a dramatic decline in the intensity of the Indian monsoon at that time. This shift coincided with the formation of extensive Northern Hemisphere ice sheets, implying a quick response of the low-latitude monsoon regime to the high-latitude glaciation. 3) At 3.14 Ma, the initial appearance of blackish-grey mud beds with long durations and occasional occurrences of lacustrine mud beds indicate that the basin was overall dominated by shallow lakes, implying a shift to decreased variability of the Indian monsoon at that time. At 2.42 Ma, an increase in the frequency and a decrease in the duration of the lacustrine mud beds suggest that deep-water lakes were frequently developed in the basin, denoting a shift to increased variability of the Indian monsoon at that time. The former shift coincides with the onset of large-scale glaciation in the circum Atlantic region and the latter corresponds to the inception of predominance of the 41 ka periodicity in Northern Hemisphere ice-sheet cover fluctuations, presumably suggesting a physical link between the Indian monsoon system and the high-latitude ice sheets in the Northern Hemisphere.

末次冰盛期以来中国东部沙地空间分布特征及环境记录

The latest two extreme scenarios of last glacial maximum and Holocene climatic optimum marked extreme situations in China. This paper aims to reconstruct the fossil extensions and paleoclimate of deserts in eastern China during this typical period. Aeolian sequence responds the climate change by virtue of alternation of aeolian sand layer and sandy soil layer, which correspond aridity and humidity, respectively. There is a set of contrastive deposits made up of loose sand layer and overlying dark sandy soil below land surface. This developed soil and underlying deep aeolian sand respond to H.O. and late last glacial, i.e. LGM. The typical bottom sand layers of about 50 profiles of Hulun Buir Desert, Horqin Desert and Otindag Desert were dated using OSL to confirm that they did deposid in LGM. Based on the locations of these LGM sand, distrution of gobi-desert-loess and landform control, the distribution in LGM of the three deserts were reconstructed. For the block of eastern mountain, the extreme eastern boundary of Hulun Buir Desert and Otindag Desert are not just functioned by climate background. The east of Horqin Desert is plain, hence eastern boundary of this desert is maily controlled by climate. It is considered that quite a lot of aeolian sand of LGM origined from fluvial deposit by observing regional distribution of river and SEM of sand grains. The environment alternation of of LGM-H.O. is featured by extensive expanse of active dune in LGM and grassland in H.O. Combined grain-size, susceptibility, TOC, colour and SEM measurement, the OSL chronology of relatively continued profiles since LGM of the three deserts are divided into four periods: eolian sand (15-10ka)- sandy soil (10-5ka)- alternation of black sand and yellow sand- reworking of LGM sand as destroy of soil.

孤岛油田曲流河微相单砂体储层建筑结构及挖潜方向研究

In the intermediary and later stage of oil field development, remaining oil disperses fiercely, the contradiction in the layer has become the main problem and the distribution of remaining oil is transforming to the difference of single sand-body. So, the fine description research of reservoir is becoming a tendency and the methods of remaining oil research need new developments. In the research of “The Single-sand-body Architectural Element and Potentiality Analysis Research of Meandering River, GuDao Oil Field”, the research principle is analytical hierarchy process and schema prescription what are reservoir fine description methods under the condition of dense well pattern. The knowledge of regional sedimentary system and sedimentary facies is the foundation of this research. According to the 3D distribution model of the microfacies sand-body of fluvial facies, stratigraphic unit classification & coenocorrelation of 154 wells are completed in the research of meandering river sand-body in Ng3-4. In this research, the 3D distribution of microfacies sand-body in the main layers are settled. The architectural element model of Ng4 point bar is analysed using the drill core and FMI data. According to the overgrow model of point bar, the surfaces of lateral accretion is traced and the architectural element model of point bar is settled. In the research, the control of micro-facies sand-body of meandering river to the distribution of remaining oil is analysed and the potential area is proposed. All these will play an important role in the development of GuDao oil field. In this research, abundant of logging data, drill core data and production performance data are used to analyse the contributing factor of single sand-body in the Ng3-4 meandering river. Using the technology of geological modeling, all that are researched including the 3D distribution scales of meandering river point bar, the control affection of inner lateral accretion layer to the distribution of oil & gas and remaining. Then, the way of remaining oil development in the sand-body of meandering river is improved. The innovation of the research technology includes (1) the presentation of the conception and research methods of micro-facies sand-body (2) enriching the content of reservoir architectural element research and (3) to renew the research method of remaining oil analysis. The research has practiced with obvious effect.(1)It is deepened into understand the river facies reservoir construction of Gudao oil field, By Building the reservoir construction and studying the effect of diffent deposit or geological interface to fluid partition and to the distribution of the remaining oil, we improved the understanding to the distribution of the remaining oil；(2)By building the distribution mod of the remaining oil in the reservoir construction and making the remaining oil description detailed,the development direction of old oil field is more clear；(3)Expanded the application scales of the horizontal well and enhanced the application effects of the horizontal well technique , we designed and drilled 23 ports horizontal wells in all , the cumulative hydrocarbon production is 10.6*104 t；(4) According to the findings of the internal building structure in reservoir of the fluvial facies in the region of interest, and uniting the injection/production corresponding states、the producing history and the dynamic monitoring documents of the oil/water wells in the flooding units , we researched the residual oil distribution in the point bar , and found the distribution regular patterns of the remaining oil, and comprehended the distribution of the remaining oil . In base of that , we proceeded the optimizing designs of the oil well potentialities , and advanced the effect of the treatment potentials . It is proved that , it was very important that internal building structure research of the single sand body of reservoir for guiding the high efficiency potentialities of the remaining oil in the high water cut stage .

孤岛油田中二北区Ng3～6储层建筑结构与油水分布规律研究

The reservoir of Zhongerbei region in Gudao Oilfield is a typical fluvial facies deposit, its serious heterogeneity of the reservoir caused the distribution of remaining oil in mature reservoirs is characterized by highly scattered in the whole field, and result to declination of production, tap potential and stabilize production is more difficult. Reservoir modeling based on lay scale can not fulfill requirement. How to further studied reservoir heterogeneity within the unit and establish the finer reservoir modeling is a valid approach to oil developing. The architectural structure elements analysis is the effectively method to study reservoir heterogeneity. Utilize this method, divide the reservoirs of Gudao Oilfield into ten hierarchies. The priority studying is sixth, seven hierarchies, ie single sand layers sand bodies By the identification of sixth, seven hierarchies, subdivide the reservoir to the single genetic unit. And to subdivide by many correlation means, such as isometry and phase transition, accomplish closure and correlation of 453 wells.Connectting fluvial deposit pattern, deposition characteristic with its log, build the inverting relation between “sedimentary facies” and “electrofacies” The process emphasize genetic communication and collocation structure of genetic body in space. By detailed architecture analyses sandbodies’ structure, this paper recognize seven structure elements, such as major channel, abandoned channel, natural levee, valley flat, crevasse splay, crevasse channel and floodplain fine grain.Combination identification of architectural structure elements with facieology and study of deposition characteristic, can further knowing genesis and development of abandoned channel. It boost the accuracy to separation in blanket channel bodies distribution, and provide reference to retrieving single channel boundary. Finally, establish fine plane and section construction. On basis architectural structure map, barrier beds and interbeds isopach map and mini-structure map, considering single thin layers to be construction unit, the main layer planimetric maps have drawn and the inner oil-water boundary have revealed. All account that architectural structure elements control remaining oil distribution in layer, and develop the study on architectural structure elements to direct horizontal well is succesful.

细粒沉积物多组分粒度特征及其成因机制研究

By using high-resolution laser grain size instrument Mastersizer 2000, the grain size distribution of windblown depositions (loess and sandy dunes), aqueous sediments (lake, river, riverside and foreshore sand), weathering crust, sloping materials and other fine-grain sediments are systemically measured. The multimodal characteristics of grain size distribution of these sediments are carefully studied. The standard patterns and their grain size characteristics of various sediments are systemically summarized. The discrepancies of multimodal distribution among windblown depositions, aqueous sediments and other sediments are concluded and the physical mechanisms of grain size multimodal distribution of various sediments are also discussed in this paper. The major conclusions are followed: 1. The multimodal characteristic of grain size distribution is a common feature in all sediments and results from properties of transportation medium, dynamic intensity, transportation manner and other factors. 2. The windblown depositions are controlled by aerodynamic forcing, resulting in that the median size of the predominant mode gradually decreases form sandy dunes to loess. Similarly, the aqueous sediments are impacted by dynamic forces of water currents and the median grain size of the predominant mode decreases gradually from river to lake sediments. Because the kinetic viscidity of air is lower than of water, the grain size of modes of windblown depositions is usually finer than that of corresponding modes of aqueous sediments. Typical characteristics of sediments grain size distribution of various sediments have been summarized in the paper: (1) Suspended particles which diameters are less than 75μm are dominant in loess and dust. There are three modes in loess’ grain size distribution: fine, median and coarse (the median size is <1μm、1-10μm、10-75μm, respectively). The coarse mode which percentage is larger than that of others is controlled by source distance and aerodynamic intensity of dust source areas. Some samples also have a saltation mode which median size is about 300-500μm. Our analysis demonstrates that the interaction of wind, atmospheric turbulence, and dust grain gravity along the dust transportation path results in a multimodal grain size distribution for suspended dust. Changes in the median sizes of the coarse and medium modes are related to variation in aerodynamic forcing (lift force related to vertical wind and turbulence) during dust entrainment in the source area and turbulence intensity in the depositional area. (2) There is a predominant coarse saltation mode in grain size distribution of sandy dunes, which median size is about 100-300μm and the content is larger than that of other modes. The grain size distribution curve is near axis symmetric as a standard logarithm normal function. There are some suspended particles in some samples of sandy dunes, which distribution of the fine part is similar to that of loess. Comparing with sandy samples of river sediments, the sorting property of sandy dunes is better than of river samples although both they are the saltation mode. Thus, the sorting property is a criterion to distinguish dune sands and river sands. (3) There are 5~6 modes (median size are <1μm, 1-10μm, 10-70μm, 70-150μm, 150-400μm, >400μm respectively) in grain size distribution of lacustrine sediments. The former 4 modes are suspensive and others are saltated. Lacustrine sediments can be divided into three types: lake shore facies, transitional facies and central lake facies. The grain size distributions of the three facies are distinctly different and, at the same time, the transition among three modes is also clear. In all these modes, the third mode is a criteria to identify the windblown deposition in the watershed. In lake shore sediments, suspended particles are dominant, a saltation mode sometimes occurs and the fourth mode is the most important mode. In the transitional facies, the percentage of the fourth mode decreases and that of the second mode increases from lake shore to central lake. In the central lake facies, the second mode is dominant. A higher content of the second mode indicates its position more close to the central lake. (4) The grain size distribution of river sediments is the most complex. It consist of suspension, saltation and rolling modes. In most situations, the percentage of the saltation mode is larger than that of other modes. The percentage of suspension modes of river sediments is more than of sandy dunes. The grain size distribution of river sediments indicates dynamic strength of river currents. If the fourth mode is dominant, the dynamic forcing of river is weaker, such as in river floodplain. If the five or sixth mode is dominant, the water dynamic forcing of rivers is strong. (5) Sediments can be changed by later forcing in different degree to form some complicated deposition types. In the paper, the grain size distribution of aqueous sediments of windblown deposition, windblown sediments of aqueous deposition, weathering crust and slope materials are discussed and analyzed. 3. The grain size distribution characteristics of different sediments are concluded: (1) Modal difference: Usually there are suspended and saltation modes in the windblown deposition. The third mode is dominant in loess dust and the fifth mode is predominant in sandy dunes. There are suspended, saltation and rolling particles in aqueous sediments. In lacustrine sediments, the second and fourth mode are predominant for central lake facies or lake shore facies, respectively. In river sediments, the fourth, or fifth, or sixth mode is predominant. Suspended modes: the grain size of suspended particles of windblown depositions usually is less than 75μm. The content of suspended particles is lower or none in sandy dunes. However, suspended particles of aqueous sediments may reach 150μm. Difference in grain size of suspended modes represents difference between transitional mediums and the strength of dynamic forcing. Saltation modes: the median size of saltation mode of sandy dunes fluctuates less than that of river sediments. (2) Loess dust and lacustrine sediment: Their suspended particles are clearly different. There is an obvious pit between the second and the third modes in grain size distribution of lacustrine sediments. The phenomenon doesn’t occur in loess dust. In lacustrine sediments, the second mode can be a dominant mode, such as central lake facies, and contents of the second and the third modes change reversely. However, the percentage of the third mode is always the highest in loess dust. (3) Dune Sand and fluvial sand: In these two depositions, the saltation particles are dominant and the median sizes of their saltation modes overlay in distribution range. The fifth mode of dune sand fluctuates is sorted better than that of fluvial sand. (4) Lacustrine and fluvial sediments: In lacustrine sediments, there are 5-6 modes and suspended particles can be predominant. The second mode is dominant in central lake facies and the third mode is dominant in lake shore facies. Saltation or roll modes occurred in central lake facies may indicate strong precipitation events. In fluvial sediments, saltation particles (or rolling particles) usually dominant. 4. A estimation model of lake depth is firstly established by using contents of the second, the third and the fourth modes. 5. The paleoenvironmental history of the eastern part of SongLiao basin is also discussed by analyzing the grain size distribution of Yushu loess-like sediments in Jilin. It was found that there is a tectonic movement before 40ka B.P. in SongLiao basin. After the movement, loess dust deposited in Yushu area as keerqin desert developed. In recent 2000 years, the climate became drier and more deserts activated in the eastern part of Song-Liao basin.

砂砾岩油藏精细油藏描述–以准噶尔盆地西北缘八区下乌尔禾组油藏为例

Glutenite reservoir is one of the most important reservoir types in china. Because of its particularity of rock structure and pore structure, it is usually difficult in development, especially for its serious heterogeneity. On the basis of seismic, well logs, core data and production performance, the lower Wuerhe group can be divided into one second-order sequences, two third-order sequences and twenty two subsequences, corresponding to the five stages and twenty two minlayers. In addition, the fault systems are interpreted and the control action of fault systems to reservoir development is also described. The lower Wuerhe formation of 8th district belongs to fluvial-dominated fan delta sedimentation, according to the analysis of well logs, logging data and core data. It can be subdivided into two kinds of subfacies and nine kinds of microfacies. The fan delta plain subfacies mainly consist of braided channel, unconcentrated flow, mud flow and sieve deposit microfacies. The fan delta front subfacies include subaqueous distributary channel, subaqueous interdistributary channel, debris flow, subaqueous barrier and grain flow microfacies. Combined with the regional geological characteristics, the porosity model of lower Wuerhe formation is performed using core data. A permeability model based on the flow zone index is also formed according to the pore throat characteristics and flow property. Finally, the heterogeneity is analyzed. The result shows that the lower Wuerhe formation has a feature of middle-high heterogeneity, and it is controlled by material sources and sedimentary facies belt.

苏里格气田苏6加密井区山1-盒8层段河流沉积体系分析

Sulige gas field is located in Northwest of Yi-Shan Slope of the Ordos Basin. The Shan 1 Member of the Shanxi Formation and He8 Member of the ShiHeZi Formation are not only objective strata of research but also main producing strata of the Sulige Field. From core and wireline log data of 32 wells in well Su6 area of Sulige field, no less than six lithofaice types can be recognised. They are Gm,Sl,Sh,Sm,Sp,Fl,Fm. Box-shaped, bell-shaped, funnel-shaped and line-segment-shaped log are typcial gamma-ray log characters and shapes. The Depositonal system of the Shan1-He8 strata in research area have five bounding-surface hierarchies and was composed of six architectural elements, CH, LS,FF（CH）,SB,LA,GB. The depositional model of Shan 1 was the type of a sandy meandering river with natural levee, abandoned channels and crevasse splay. Channel depth of this model maybe 7-12 m and the fullest-bank flow can reach 14 m high. Based on analysis of depositional causes, a sandy braided river model for the depositional system of He 8 can be erected. It consists of active main channels, active chute channels, sheet-like sand bars, abandoned main channels and abandoned chute channels. Channel depth of this model can be 3-4 m with 9 m of highest flow. Six gamma-ray log cross sections show that the connectivity of sandbodies through Shan 1 Member is lower than He 8. Influenced by occurrence of mudy and silty deposits, vertical connectivity of sandbodies through He 8 is not high.

孤东油田馆陶组河流相储层流动单元模型与剩余油分布规律研究

Since C.L. Hearn presented the concept of flow unit in 1984, its generation mechanisms and controlling factors have been studied in many aspects using different methods by researchers. There are some basic methods to do the research, and there are several concepts and classification standards about flow unit. Based on previous achievements and using methodologies from sedimentary geology, geophysics, seismic stratigraphy, and reservoir engineering, the author systemically studies the factors controlling flow unit, puts forward a series of methods for recognition, classification and evaluation of flow unit. The results obtained in this paper have important significance not only for understanding the flow unit, but also for revealing the distribution of remaining oil. As a case, this paper deals with the reservoir rocks in Guantao Group of Gudong Oilfield. Zhanhua Sag, Jiyang Depression in Bohaiwan Basin. Based on the study of stratigraphic, depositional and structural characteristics, the author establishes reservoir geological models, reveals the geological characteristics of oil-bearing reservoir of fluvial facies, points out the factors controlling flow unit and geological parameters for classification of flow unit. and summarizes methods and technologies for flow unit study when geological, well-logging and mathematical methods are used. It is the first attempt in literatures to evaluate reservoir by well-logging data constrained by geological conditions, then a well-logging evaluation model can be built. This kind of model is more precise than ever for calculating physical parameters in flow unit. In a well bore, there are six methods to recognize a flow unit. Among them, the activity function and intra-layer difference methods are the most effective. Along a section, the composition type of flow unit can be located according amplitude and impedance on seismic section. Slice method and other methods are used to distinguish flow unit. In order to reveal the distribution laws of flow unit in space, the author create a new method, named combination and composition of flow unit. Based on microscopic pore structure research, the classification methods of flow unit are developed. There are three types of flow unit in the reservoir of fluvial facies. They have their own lithology, petrophysics and pore structure character. Using judgement method, standard functions are built to determine the class of flow unit of fluvial facies. Combining reservoir engineering methods, the distribution laws of remaining oil in different types, or in different part of a flow unit are studied. It is evident that the remaining oil is controlled by the type of flow unit. The author reveals the relationship between flow unit and remaining oil distribution, builds the flowing models, predicts the variation of reservoir parameters in space, put forward different methods developing remaining oil in different flow unit. Especially, based on the results obtained in this paper, some suggestions for the adjustment of the developing flow units have been applied in Districts No.4 and No.7, and good results have been yielded. So, the results of this paper can guide oil field development. They are useful and significant for developing the remaining oil and enhancing the oil recovery efficiency.

新第三纪红河盆地特征及红河断裂活动对其形成与发育的控制

Based on geodynamic analysis of sedimentary basins, combined sedimentology with structural geology and other methods, the author studied the Honghe basin located in Yunnan province of Southwestern China. Sandstone slice grain size analysis, combined with field geology and indoors study indicate that a set of inland alluvial fan diposits, fluvial deposites, delta deposits and some lacustrine sediments are in Honghe basin. Studying on shape of the Honghe basin, sedimentary and structural characteristic and distribution of different kinds of conglomerate and its structural significance, we hold the idea that the formation and evolution of Honghe basin are controlled by the activity of Red River faut. Correlation of lithostratic cross section in Honghe basin and studying on activity of Red River fault indicate that Honghe basin was formed in two stages. It is a complex basin constitutes of the first-stage trans-releasing basin and the second-stage trans-downfaulted basin. Due to the uplift of Qinghai-Xizang plateau and deformation of orogeny, the western Yunnan and adjacent area move to SE direction as a result of Tectonic Escape. Right lateral strike slip occurred along Red River fault, trans-releasing basin formed at the bend part of the fault due to stress relexation. As the block escaping, it moves away from the other block of the Red River fault, the upper block move down obliquely and trans-downfaulted basin formed. Combined the age of phytolite and regional structural events, we think the first-stage transreleasing basin was formed in late Miocene, on the other words, the dextral strike slip of Red River fault may began in late Miocene (10-7Ma). The second-stage trans-downfaulted basin may be formed in early stage of Pliocene (about 4.7Ma). Subsequently, the bilateral faults dipping to the inside of the plateau and thrusting outwards occurred in the marginal region of Qinghai-Xizang plateau during its uplifting as a fan-shaped mountain body, this results in the uplift of the strata to the east of Red River fault and supply large quantity of provenance for the Honghe basin. In last Pliocene (about 3Ma), strong uplift of Qinghai-Xizang plateau leads to massive clastic sediment entered Honghe basin and causes its closure. As a kind of trans-tentional basin, trans-releasing basin is different to pull-apart basin. The author compared the Mosha trans-releasing basin with Jinggu pull-apart basin in SW Yunan, China, and described their character correspondingly. Otherwise, the author combined the predecessors' studding with conclusion of own study, discussed the kinematics of Ailaoshan-Red River belt in Cenozoic, and the relationship between the formation of Honghe basin and uplifting of Qinghai-Xizang plateau.

河道砂油藏产能预测系统研究

Productivity prediction is a serious factor to oil reservoir management and working out economic plans so that it is paid great attention to all the time. Gudao Oil Field, which has been yielding more than 100 million tons of crude oil accumulatively since it was put into developing in 1970's as a complete set of oil field, now entering double extra high water-bearing period after productivity construction, stable production and depletion stage. It's main layer series of development is thought to be type of channel sand reservoir in east China. Form channel sand reservoir in upper Guantao Group of Shengli Oil Field, there are several large oil fields such as Gudao, Gudong and Chengdao etc. with almost one-third reserves of whole Shengli Oil Field. It is considered the common characteristics in this area would be that the layer is less developed, the sand distribution is sporadic, the connectivity is weak, the heterogeneity is strong in plane, the oil layer is unconsolidated with big porosity, high permeability and serious sanding, and the oil is heavy. Because of the restricted factors to productivity of this kind of reservoir, it is very significant to study the productivity prediction this kind of reservoir. By selecting the upstream fluvial reservoir in Guantao Group of Neogene system as researching object, the author studied the forecasting technology with heterogeneous reservoir. Firstly, the author constructed the 3D subtle geological model quantificationally through researching exploitation geology in the way of combination of dynamic and static methods. Secondly, by the aid of dynamic material obtained while producing, the author analyzed the oil distribution law and influencing factors, then finished dynamic oil reservoir description on the basis of static oil reservoir description. Thirdly, via comparing and analyzing all the forecasting methods of productivity existed, the author developed a set of method to forecast productivity of single well and oil field which fit to channel sand reservoir. At last, under the support of ORACLE database, with the advanced computer technology, the author programmed the software called 'Channel Sand Reservoir Prediction System'. Up to now, this system has been putting into use in Gudao Oil Field and very successful.

陇西盆地晚第三纪风尘沉积的地层学研究

In Asia, the significant environment changes in Cenozoic include: uplift of Himalayas and Tibetan Plateau, formation Asian monsoon system, Aridification in Central Asia. One of major advances in recent studies of eolian deposit on the Loess Plateau is the verification of the eolian origin for the Late Tertiary Hipparion Red-Earth (also called red-Clay) underlying the Quaternary loess. Thus, the Late Tertiary eolian deposit, which has been proven a nearly continuous terrestrial record and sensitive to climate change, provides us an important archive to understand these above Cenozoic environment events. The deposit in eastern Loess Plateau has been extensively studied, while the property and age of deposit underlying the Quaternary loess in western plateau remains unclear. In this paper, detail investigations were made on the Sedimentology, geochemistry of Longxi section, a typical section in western Loess Plateau, to address its origin, and on micromammalian fossils and magnetostratigraphy to address its age. The main conclusions are presented as following: 1. The sedimentological and geochemical properties in Longxi section are highly similar to typical Quaternary eolian deposit in Loess Plateau. Nearly 100 paleosols are recognized in the field, and the grain size are very fine with the median grain size centered at 4～7μm. There is a good agreement of both major and trace element compositions between Longxi deposit and the Quaternary Loess. The REE distribution patterns of Longxi deposit and the Quaternary loess are remarkably similar in shape, with enrichment LREE and fairly flat HREE profiles and clear negative Eu anomaly. The mangnetic minerals in Longxi deposit are mainly magnetite, hematite and maghematite, which are similar to those of the Hipparion Red-Earth and Quaternary Loess. The major difference among them is that the samples from Longxi section contain more hematite. The characteristics of anisotropy of magnetic susceptibility (AMS) in Longxi deposit is highly consistent with that of Quaternary loess, while values of the major AMS parameters, e.g. anisotropy degree, magnetic foliation and lineation, are significantly lower than those of fluvial and lake deposits. These evidences indicate an eolian origin for the sediment. 2. An investigation of micromammalian fossils was firstly carried out for determining the approximate age of the sequence because of lack of materials for accurate isotope dating. Three fossil assemblages were obtained which indicate a chronological range from the Middle Miocene to Late Miocene. The magnetostratigraphical study suggests that it is a near continuous terrestrial record for the period from 13.23 to 6.23 MaB.P. The obtained chronology is highly consistent with fossils assemblages. This section is the oldest eolian deposit presently known in Loess Plateau. 3. The magnetic susceptibly value is high in paleosols than in surrounded weak-weathered layers, which suggests that it may be a climate index on orbital time scale. While it cannot be used as a proxy to address the long-term, change of climate on tectonic time scale, as content of the magnetic minerals is highly variable in different parts of the section. 4. The appearance of Middle Miocene eolian deposit in the Loess Plateau marks the strengthening of aridification of Central Asia. The high degree of similarity between the geochemical properties of Longxi eolian deposit, Hipparion Red-Earth and Quaternary loess a suggests that a rather similar source provenance. The dust accumulation rate (DAR) of Longxi section, which is widely used as a proxy to document the aridity in source areas in marine and terrestrial record studies, recorded the aridity condition in northwestern China over a period from Middle Miocene to Late Miocene. The DAR of the section shows that the continent aridity remains moderate and relative stable over that period.

河流成因储层沉积微相与剩余油分布及形成机理研究

Based on the study of fluvial sandstone reservoir in upper of Guantao group in Gudao and Gudong oilfields, this paper first introduces A.D.Miall's(1996a) architectural-element analysis method that was summarized from ground outcrop scale into the reservoir formation research of the study area, more subtly divides sedimentary microfacies and establishes sedimentary model of research area.on this base, this paper summarizes the laws of residual oil distribution of fluvial formation and the control effect of sedimentary microfacies to residual oil distribution, and reveals residual oil formation mechanism. These results have been applied to residual oil production, and the economic effect is good. This paper will be useful for residual oil research and production and enhancement of oil recovery in similar reservoir. The major conclusions of this paper are as follows. 1. Using the architectural-element analysis method to the core data, a interfacial division scheme of the first to the dixth scale is established for the studied fluvial formation. 2.Seven architectural-elements are divided in upper of Guantao group of study area. The sandstone group 5～1+2 of Neogene upper Gutao group belongs to high sinuous fine grain meandering river, and the sandstone group 6 is sandy braided river. 3. Inter layer, the residual oil saturation of "non-main layer" is higher than "main layer", but the residual recoverable reserve of former is larger. Therefore, "main layer" is the main body of residual oil distribution. The upper and middle part of inner layer has lower permeability and strong seeping resistance. Addition to gravity effect in process of driving, its driving efficiency is low; residual oil saturation is high. Because of controlling of inside non-permeable interlayer or sedimentary construction, the residual oil saturation of non-driving or lower driving efficiency position also is high. On plane, the position of high residual oil saturation mostly is at element LV, CS, CH (FF), FF etc, Which has lower porosity and permeability, as well as lens sand-body and sand-body edge that is not controlled by well-net, non-perfect area of injection and production, lower press difference resort area of inter-well diffiuent-line and shelter from fault, local high position of small structure. 4.Microscopic residual oil mainly includes the non-moved oil in the structure of fine pore network, oil in fine pore and path, oil segment in pore and path vertical to flow direction, oil spot or oil film in big pore, residual oil in non-connective pore. 5.The most essential and internal controlling factor of fluvial formation residual oil distribution is sedimentary microfacies. Status of injection and production is the exterior controlling factor of residual oil distribution. 6. The controlling effect of formation sedimentary microfacies to residual oil distribution indicates inter-layer vertical sedimentary facies change in scale of injection and production layer-series, planar sedimentary face change and inner-layer vertical sedimentary rhythm and interbed in single layer to residual oil distribution. 7. It is difficult to clear up the inter-layer difference in scale of injection and production layer-series. The using status of minor layer is not good and its residual oil saturation is high relatively. It is obvious that inter-layer vertical sedimentary facies changes control inter-layer residual oil distribution at the same or similar conditions of injection and production. For fluvial formation, this vertical sedimentary facies change mainly is positive gyration. Namely, from down to top, channel sediment (element CHL, LA) changes into over-bank sediment (element LV, CR, CS). 8. In water-injection developing process of transverse connecting fluvial sandstone oil formation, injection water always comes into channel nearby, and breaks through along channel and orientation of high pressure gradient, does not expand into side of channel until pressure gradient of channel orientation changes into low. It brings about that water-driving status of over-bank sedimentary element formation (LV, CR, CS) is not good, residual oil saturation is high. In non-connective abandoned channel element (CH) formation with channel, because this reverse is difficult to control by injection and production well-series, its using status is not good, even terribly not good, residual oil is enrichment. 9. The rhythm and sedimentary structure, sedimentary facies change in single sand body brings about vertical changes of formation character, growth character of inner layer interbed. These are important factor of controlling and affecting vertical water spread volume and inner layer residual oil forming and distribution in single sand body. Positive rhythm, is the principal part of fluvial sandstone inner layer sedimentary rhythm. Namely, from down to upside, rock grain granularity changes from coarse to fine, seeping ability changes from strong to feebleness. It brings about that water-driving status of inner layer upside is not good, residual oil saturation is high. Inner layer interbed has different degree affecting and controlling effect to seeping of oil and water. Its affecting degree lies on interbed thickness, extending scale, position, and jeted segment of production or injection well. The effect of interbed at upside of oil formation to oil and water seeping is less; the effect of interbed at middle of oil formation to oil and water seeping is more. 10. Indoor experiment and research indicate that wettability, permeability step, vertical permeability, position of Kmax and ratio of oil viscousity and water viscousity all have great effect on the water-driving recovery ratio. 11. Microscopic residual oil distribution is affected and controlled by formation pore network structure, pressure field distribution, and oil characteristic. 12.The residual oil forming mechanism: the over-bank sedimentary element and upper part of a positive rhythm sandstone have fine pore and throat network, permeability is low, displacement pressure of pore and throat is high. The water-driving power usually falls short of displacement pressure that brings about injection water does not spread into these pore and throat network, thereby immovable oil area, namely residual oil, is formed. At underside of channel sedimentary element and positive rhythm sandstone, porosity and permeability is relatively high, connecting degree of pore and throat is high, displacement pressure of pore and throat is low. Thereby injection water is easy to enter into pore and throat, driving oil in them. Because the pore space is irregular, the surface of pore wall is coarse and non-flat. That the oil locate on concave hole of pore wall and the dead angle of pore, and the oil attaches on surface of pore wall by surface tension, are difficult to be peeled off, becoming water-driving residual oil (remaining oil). On the other hand, Because flowing section lessens, flowing resistance increase, action of capillary fore, or seeping speed decreases at process of transfer at pass narrow throat path in the course carried by driving water. The "oil drop", "oil bead", or "oil segment" peeled off by driving water is difficult to carry and to drive out by water at less pressure difference. Thereby they are enclosed in pore to form discontinuous residual oil. 13.This results described above have been applied in nine develop blocks of Gudao and Gudong oilfield. Its applying effect is marked through local injection production adjustment, deploying replacement well, repair hole, replacement envelop, block off water and profile control etc. Relative method and technology can be applied to other oil production area of Shengli oilfield, and obtain better economic and societal effect.