A new species of Allocreadium (Trematoda : Allocreadiidae) from freshwater fishes in the Danjiangkou Reservoir in China

A new species of Allocreadium, Allocreadium danjiangensis n. sp., is described from the intestine of several species of freshwater fish, including Abbottina rivularis (Basilewsky, 1855), Sarcocheilichthys nigripinnis nigripinns (Gunther, 1873), Gnathopogon argentatus (Sauvage et Dabry 1874), Opsariichthys uncirostris bidens (Gunther, 1873), and Erythroculter mongolicus mongolicus (Basilewsky, 1855) (Cyprinidae) from the Danjiangkou Reservoir in central China. The main morphological characters of the new species are as follows: vitelline follicles numerous, extending from the level of acetabulum to posterior extremity, distributed over both sides around the ceca; cirrus sac relatively large, developed, lying obliquely anterior to the acetabulum, extending from the level of the intestinal bifurcation to the central level of acetabulum, and overlapping left or right cecal; and ovary much smaller than testes, generally close to or even overlapping the anterior border of anterior testis. Observation by scanning electron microscopy shows only 2 kinds of tegumental formations, i.e., papillae and tubercles, instead of 3 types of tegumental formations, i.e., papillae, bosses, and minute sensor receptors observed on other species of the Allocreadiidae. The tegumental striations of the present species vary on the different parts of the body. In addition, a new structure, identified as the "groove" with a tonguelike tubercle, was observed on the inner wall of acetabulum.

基于3×3耦合器的迈克尔逊干涉仪相位特性分析

国家８６３计划（２００７ＡＡ０３Ｚ４１５）

基于LDA模型的文本分割

文本分割在信息提取、文摘自动生成、语言建模、首语消解等诸多领域都有极为重要的应用.基于LDA模型的文本分割以LDA为语料库及文本建模,利用MCMC中的Gibbs抽样进行推理,间接计算模型参数,获取词汇的概率分布,使隐藏于片段内的不同主题与文本表面的字词建立联系.实验以汉语的整句作为基本块,尝试多种相似性度量手段及边界估计策略,其最佳结果表明二者的恰当结合可以使片段边界的识别错误率远远低于其它同类算法.

多室流化床内固体颗粒的流动行为研究——褐煤有效利用项目的冷态实验

基于褐煤热分解时既除去煤中的氮、又可回收焦油这一特点,该文针对褐煤的水分、灰分含量高及热解时释放的挥发份多但燃烧热值低而导致褐煤总的热值低、热利用效率不高的问题,提出了一种有效利用褐煤的方案:利用多室流化床技术,褐煤首先于缺氧条件下在热分解室内热解,释放出挥发份、水分、从挥发份中冷凝出焦油;然后热解得到的高热值的褐煤焦炭通过多室流化床的室与室之间分隔板上的开孔流入燃烧室内燃烧.这样处理既克服了褐煤热值低的缺点,又利用了其挥发份多的特点,收集到焦油.该文的研究工作作为该方案的冷态实验部分,在小型多室流化床冷态实验装置上,对固体颗粒(如由褐煤得到的焦炭等)通过多室流化床的室与室之间的分隔板上之开孔流通的行为及规律进行了研究. 

基于3×3耦合器的迈克耳孙干涉仪相位特性分析

研究了基于3×3耦合器的非平衡迈克耳孙干涉仪的相位特性。由光纤耦合器的散射矩阵理论,推导出了当3×3耦合器分光比不均匀时,干涉仪三路输出信号相位差的表达式。根据实际使用的3×3耦合器各通道的插入损耗,经计算与修正得到其散射矩阵,并求出干涉仪三路输出信号的相位差分别为120.21°、120.77°和119.02°,与理想值120°的偏差在1°以内。实验测得的干涉仪三路输出信号的相位差随时间随机变化,经分析是由光偏振态随机变化引起的。相位差与理想值120°的偏离均在1°以内,符合理论分析得到的结论。

微生物法沥取重金属污泥中铬的研究

本文研究了两种微生物及其组合沥取、回收用微生物法治理电镀铬废水产生的铬污泥中的铬。铬污泥富含C、N、O，含铬量为13%， 经X-光电子能谱分析铬以三价态(氢氧化铬)存在。二种微生物分别从一酸性矿水和酸性污泥中分离筛选得到，经鉴定为硫杆菌属 (Thiobacillus Beijerinek)的两个不同种，一为氧化亚铁硫杆菌(Thiobacillu ferrooxidans, TF), 另一为氧化硫硫杆菌 (Thiobacillus thiooxidans, TT)。研究并比较了不同微生物对污泥中铬的沥取能力，结果表明，TT菌沥取铬效率最高。振荡、动 态淋滤、静置等沥取方式经过研究表明动态淋滤为最佳，室温条件下(15-20℃)，污泥浓度为20g/L时，总铬沥出率达60%时所需时 间：动态淋滤为48.5h，振荡和静置方式分别为91.22，81.6h。研究了不同温度、不同起始PH、不同污泥浓度及非成熟菌液对微生 物沥取能力的影响：(1) 沥取前期，温度对铬的沥出影响较大；微生物沥取反应基本属一级反应；温度与反应速率的关系基本符合 Arrhenius方程，但沥取后期这一特点并不突出。(2) 沥取液最适起始PH为菌液自然PH；PH值的人为改变将使铬的沥出大大降低。 (3) 污泥浓度与铬的沥出呈正相关，但浓度高于30g/L时，铬的沥出量不再增加。(4) 非成熟菌液沥出铬的能力较差，但沥取液中 微生物生长繁殖较为活跃。总结微生物沥取反应最佳沥取条件为：TT成熟菌液、污泥浓度10g/L、温度25-36℃、动态淋滤方式，此 时铬几乎可100%从污泥中沥出。经扫描电镜分析，沥取开始时，微生物紧密吸附于污泥颗粒表面上，表面紧密吸附为微生物发挥功 能提供了基础。微生物沥取污泥中铬的反应机理推测为：硫细菌代谢产硫酸或氧化Fe2+成Fe3+，利用酸，Fe3+ 及自身氧化酶系统 氧化污泥中Cr3+为Cr6+,Cr6+溶出结晶为CrO3。This paper has studied bioleaching and recovery of Chronium(Cr)from electroplating sludge by two consortum of bacteria and their combination, with sludge produced by microbiological process treating electroplating wastewater containing Cr as material. The share of Cr is 13% and its state is Cr (OH)3 in the sludge. One of the bacteria in the paper was isolated from acid sewage sludge and the other was from acid mineral water. The former was tested and determined as Thiobacillus ferroxidans(TF) and the latter was Thiobacillus thiooxidans(TT). Different microorganisms, responsible for the metal leaching activity, have great influence on the efficiency of leaching. The results showed that TT has biggest power. Experiments were conducted to examined effects of three different ways of leaching(Shaking, Down-leaching, Static-leaching). When temperature was in-door's (15-20℃)and concentration of the sludge was 20g/L, the bioleaching time required to reach 60% of Cr solubilization with the above three ways were 91.2, 48.5, 81.6h respectively. Down-leaching was proved to be the most efficient. The influence of different temperature, initial PH, concentration of the sludge and non-mature inoculum had been studied. The results obtained reveal that: (1) The variation of temperature is important during the time from initial to middle of leaching. The reaction of bioleaching belongs to first-order. The relation between the bioleaching rate constant(In k)and temerature can be expressed by Arrhenius function. (2) The fittest initial PH is the nature PH of mature inoculum. Any alteration with it could cause clearly negative effection. (3) The concentration of the sludge can make strong influence on the bioleaching efficiency. But when the concentration is above 30g/L, the increasing of Cr in the solution is little. (4) If non-mature inoculum acts as the bioleachin microorganism, little quantity of Cr would be gained from the sludge. But the micormass in the solution is very active. The results from electron microscope showed that microorganisms adhered to the surface of the sludge and the adherence was the first stage of the bioleaching. Some salts of Cr can be obtained afer the water of the bioleaching solution being evaporated. By analysing the results of experiment with X-Ray spectroscopy, the salt was identified as CrO3. The recovery rate of Cr is 78.4%.

Isoscaling parameter a as a possible probe of medium effect of nucleon-nucleon cross section

The medium effect of nucleon-nucleon cross section sigma(med)(NN) (alpha(m)) on the isoscaling parameter a is investigated for two central nuclear reactions Ca-40+Ca-40, Ca-60+Ca-60. within isospin-dependent quantum molecular dynamics at beam energies from 40 to 50 MeV/nucleon. It is found that there is the very obvious medium effects of nucleon-nucleon cross section sigma(med)(NN)(alpha(m)) on the isoscaling parameters a. In this case the isoscaling parameter a is a possible probe of the medium effect of nucleon-nucleon cross section sigma(med)(NN)(alpha(m)) in the heavy ion collisions. The mechanism of the above-mentioned properties is studied and discussed.

Using HPLC retention parameters to estimate fish bioconcentration factors of organic compounds

Reversed-phase high performance liquid chromatography (RP-HPLC) was employed to develop predictive models for fish bioconcentration factors (BCF) of organic compounds. Estimation of BCF from RP-HPLC retention parameters on octadecyl-bonded silica gel (ODS), cyanopropyl-bonded silica gel (CN), and phenyl-bonded silica gel (Ph) columns were investigated. The results show that, for a set of compounds belonging to different chemical classes, the CN stationary phase is the best one among the three columns and better than n-octanol/water model for BCF estimation. A multi-column RP-HPLC model, using the retention parameters on the CN and Ph columns as the variables of multiple linear regression equations, was further evaluated to estimate BCF of organic compounds belonging to different chemical classes, and the results show that the multi-column RP-HPLC model is better than that of any single RP-HPLC column for BCF estimation.

Gas permeation performance of cellulose hollow fiber membranes made from the cellulose/N-methylmorpholine-N-oxide/H2O system

Cellulose hollow fiber membranes (CHFM) were prepared using a spinning solution containing N-methylmorpholine-N-oxide as solvent and water as a nonsolvent additive. Water was also used as both the internal and external coagulant. It was demonstrated that the phase separation mechanism of this system was delayed demixing. The CHFM was revealed to be homogeneously dense structure after desiccation. The gas permeation properties of CO2, N-2, CH4, and H-2 through CHFM were investigated as a function of membrane water content and operation pressure. The water content of CHFM had crucial influence on gas permeation performance, and the permeation rates of all gases increased sharply with the increase of membrane water content. The permeation rate of CO2 increased with the increase of operation pressure, which has no significant effect on N-2, H-2, and CH4. At the end of this article a detailed comparison of gas permeation performance and mechanism between the CHFM and cellulose acetate flat membrane was given. (C) 2003 Wiley Periodicals, Inc.

Anodic Stripping Voltammetry at Bismuth-Coated and Uncoated Carbon Microdisk Electrodes:Application to Trace Metals Analysis in Flood Samples

This article reports on the performance of a bismuth-coated carbon microdisk electrode (BiFμE) for the determination of trace heavy metals by anodic stripping voltammetry (ASV). The BiFμE was prepared by electrodeposition of a metallic bismuth film onto the microdisk, by applying an in-situ electroplating procedure. To test the performance of the BiFμE, ASV measurements were performed on synthetic solutions containing Cd2+, Pb2+, and Cu2+ as target ions. The results indicated that cadmium and lead gave well-defined ASV peaks with no interference, and their quantitative determination could be carried out straightforwardly. In particular, linear calibration curves over the range 5.0 x 10-8-1.0 x 10-6M for both ions, and detection limits of 7.8 and 2.9 nM, for cadmium and lead, respectively, after applying a 60 sec preconcentration step, were obtained. The reproducibility was also satisfactory, the relative standard deviation (RSD) being within 2.5% for both ions. Copper, instead, gave an ASV response that. in most experimental conditions, overlapped with that of bismuth. This circumstance made the determination of copper at the BiFμE difficult. Since the latter element could be detected reliably at the uncoated carbon microdisk electrode (CμE), both BiFμE and CμE were employed, respectively, for the determination of lead and copper ions in drinking water, wine, and tomato sauce.

Bulk ultrafine binderless (W0.4Al0.6)C prepared by high pressure sintering

Pure (W0.4Al0.6)C powder of about 1 mu m in diameter was sintered by the high pressure sintering (HPS) process without the addition of any binder phase. The microstructure, Vickers micro hardness and density versus the sintering time and temperature are well described. The most suitable sintering condition under pressure of 4.5 GPa is 1873 K for 8 min. Under this sintering condition, the hardness can reach 2295 kg mm(-2) and the relative density can reach 98.6%.