等离子体湍流对电子的加速

本文讨论了等离子体湍流对电子加速的两种模型:（1）假定在空间中存在一个空间均匀的等离子体湍流区,当具有一定初始分布的电子束通过此湍流区时,研究湍流场对电子束的加速过程;（2）在某一封闭的区域中,存在着具有一定初始分布和空间均匀的等离子体,当某种类型的等离子体波突然传入此等离子体区,然后考察此区中电子的加速过程。在这两种模型中,可能存在着某种电子消失机制。假定湍谱是幂指数形式,我们给出了不同类型湍流扩散系数的普遍形式。利用较简单的数学方法,求解了包括消失过程的一维准线性动力学方程,对于给定的初始分布,得出了分布函数的解析解,并给出了平均能量时间关系的表达式。另外,对于特定的湍谱指数,解出了当平行电场和湍流同时存在时的分布函数。最后,对所得结果进行了数值分析和讨论。

水煤浆多级气动喷嘴的喷雾特性研究

本文研究了一种多级气动喷嘴对水煤浆燃料的喷雾特性。采用实验的方法研究了水煤浆性质（动态表面张力和表观粘度）、喷嘴操作工况和喷嘴几何结构对射流雾化细度的影响,给出喷嘴雾炬轴向粒度分布,并对相关结果进行了分析。

水中悬浮隧道在冲击载荷作用下的计算模型与数值模拟

建立了水中悬浮隧道在冲击载荷作用下的简化计算模型。用等效质量法将圆柱壳分布质量折算成冲击点处的集中质量,模型中考虑流体附加质量和系统阻尼的影响。根据碰撞过程中的动量守恒、变形过程中的能量守恒以及结构的位移与内力关系,得到问题的解析解。为验证解析解,在ANSYS/LS-DYNA中建立了动态冲击有限元分析模型。通过算例分别考察了在忽略和考虑流体附加质量两种情况下,冲击点位置和冲击速度对冲击点处最大径向位移的影响,将解析解与数值解进行对比,结果吻合较好。然后采用数值模拟方法得到了系统阻尼对计算结果的影响规律。数值模拟过程中还可以得到冲击点处的最大Mises应力。

铁基抗高温磨损激光熔覆涂层强韧设计和研究Ⅰ:激光熔覆合金成分、微观结构强韧化设计及涂层制备

本文在对热工模具进行失效分析的基础上，利用激光熔覆技术，在５ＣｒＭｎＭｏ基础上设计并制备强韧兼备的抗高温磨损涂层。

Receptivity to free-stream disturbance waves for blunt cone axial symmetry hypersonic boundary layer

Based on high-order compact upwind scheme, a high-order shock-fitting finite difference scheme is studied to simulate the generation of boundary layer disturbance waves due to free-stream waves. Both steady and unsteady flow solutions of the receptivity problem are obtained by resolving the full Navier-Stokes equations. The interactions of bow-shock and free-stream disturbance are researched. Direct numerical simulation (DNS) of receptivity to free-stream disturbances for blunt cone hypersonic boundary layers is performed.

Parametric studies of tension leg platform with large amplitude motions

Tension leg platform (TLP) is an important kind of working station for deep water exploration and development in ocean, whose dynamic responses deserve a serious thought. It is shown that for severe sea state, the effects of nonlinearities induced by large displacements of TLP may be noteworthy, and then employment of small displacements model should be restrained. In such situation, large amplitude motion model may be an appropriate alternative. The numerical experiments are performed to study the differences of dynamic responses between the two models. It is shown that for most cases, differences between results of the two models are significant. The variances of the differences vs. the wave period are the most remarkable, and that of the differences vs. wave heading angle are also apparent.

板壳断裂力学

本书阐明了板壳断裂理论的基础。论证了Reissner型板壳断裂理论的科学性、经典板壳断裂理论的缺陷及在一定范围内仍具有的实用价值；介绍了作者所创意的研究Reissner型板壳断裂纹尖端场的方法等。

目录

饱和-非饱和土中渗流Richards方程有限元算法

发展了一种求解理查森方程的一般有限元算法.该方法采用积分法处理孔隙水压力对时间的导数项,采用集中质量技术处理有限元方程中质量矩阵来保证数值稳定.所采用的质量守恒迭代方法不须改变迭代方式,采用一般的Picard迭代方法.该方法能求解入渗、地下水位瞬变和排水等范围广泛的饱和-非饱和渗流问题.对3个已公开发表具有详细试验数据的算例的模拟表明,该方法对入渗锋、稳定渗流地下水位和非稳定渗流溢出面都模拟很好.Pieard迭代方法效率很高,且无数值振荡发生.

A Mechanical Model For The Quantification Of The Effect Of Laser Quenching On Ctod In Steels

The technology of laser quenching is widely used to improve the surface properties of steels in surface engineering. Generally, laser quenching of steels can lead to two important results. One is the generation of residual stress in the surface layer. In general, the residual stress varies from the surface to the interior along the quenched track depth direction, and the residual stress variation is termed as residual stress gradient effect in this work. The other is the change of mechanical properties of the surface layer, such as the increases of the micro-hardness, resulting from the changes of the microstructure of the surface layer. In this work, a mechanical model of a laser-quenched specimen with a crack in the middle of the quenched layer is developed to quantify the effect of residual stress gradient and the average micro-hardness over the crack length on crack tip opening displacement (CTOD). It is assumed that the crack in the middle of the quenched layer is created after laser quenching, and the crack can be a pre-crack or a defect due to some reasons, such as a void, cavity or a micro-crack. Based on the elastic-plastic fracture mechanics theory and using the relationship between the micro-hardness and yield strength, a concise analytical solution, which can be used to quantify the effect of residual stress gradient and the average micro-hardness over the crack length resulting from laser quenching on CTOD, is obtained. The concise analytical solution obtained in this work, cannot only be used as a means to predict the crack driving force in terms of the CTOD, but also serve as a baseline for further experimental investigation of the effect after laser-quenching treatment on fracture toughness in terms of the critical CTOD of a specimen, accounting for the laser-quenching effect. A numerical example presented in this work shows that the CTOD of the quenched can be significantly decreased in comparison with that of the unquenched. (C) 2008 Elsevier B.V. All rights reserved.

Interface Fracture Behavior Of Electroplated Coating On Metal Substrate Under Compressive Strain

The inducement of interface fracture is crucial to the analysis of interfacial adhesion between coating and substrate. For electroplated coating/metal substrate adhering materials with strong adhesion, interface cracking and coating spalling are difficult to be induced by conventional methods. In this paper an improved bending test named as T-bend test was conducted on a model coating system, i.e. electroplated chromium on a steel substrate. After the test, cross-sections of the coated materials were prepared to compare the failure behaviors under tensile strain and compressive strain induced by T-bend test. And the observation results show that coating cracking, interface cracking and partial spalling appear step by step. Based on experimental results, a new method may be proposed to rank the coated materials with strong inter-facial adhesion. (C) 2008 Elsevier B.V. All rights reserved.

Probing single-molecule by surface-enhanced resonance Raman scattering with linearly and circularly polarized laser

Rhodamine 6G (R6G) was incubated in silver sols with different low concentrations and its surface-enhanced resonance Raman scattering (SERRS) spectra, excited by linearly and circularly polarized light, respectively, were studied. At the single-molecule level the SERRS spectra were recorded in 10(-13) M dye colloidal solution. Spectral inhomogeneous behaviors from single-molecule were observed such as spectral polarization, spectral diffusion and intensity fluctuations of vibrational lines. Difference between SERRS spectra of R6G excited by linearly and circularly polarized light and the effect of the polarizing angle of Raman signal relative to the slit of spectrograph on the Raman spectral polarization were analyzed and measured experimentally. Circularly polarized laser and the correction of the polarizing angle of Raman signal are necessary to avoid fake results in the measuring of Raman spectral of single-molecule, which was not noticed in initial papers. (c) 2005 Elsevier B.V. All rights reserved.

Crystallization of amorphous Ge2Sb2Te5 films induced by a single femtosecond laser pulse

Crystallization is achieved in amorphous Ge2Sb2Te5 films upon irradiation with a single femtosecond laser pulse. Transmission electron microscopy images evidence the morphology of the crystallized spot which depends on the fluence of the ferntosecond laser pulse. Fine crystalline grains are induced at low fluence, and the coarse crystalline grains are obtained at high fluence. At the damage fluence, ablation of the films occurs. (C) 2004 Elsevier Ltd. All rights reserved.

Photobleaching process of xanthene dyes initiated by N-phenylglycine in the polyvinylalcohol film

The parameters such as quantum yield and molar absorption coefficients of the photoinitiator that are responsible for holographic sensitivity in photopolymer material are investigated with a single beam exposure experiment. The influence of exposure intensity, the concentrations of N-phenylglycine and dye on the photobleaching process of xanthenes dyes are presented. In addition, the effect of diphenyliodonium hexafluorophosphate salt on the quantum yield and molar absorption of xanthene dyes is studied. (c) 2005 Elsevier Ltd. All rights reserved.

Si underlayer induced nano-ablation in AgInSbTe thin films

AgInSbTelSi thin films on glass substrates are prepared by dc magnetron sputtering at room temperature. Using Si underlayer as the thermal diffusion layer, the super-resolution nano-ablation holes with a size of 70nm in the AgInSbTe phase change films are obtained by a far-field focused laser experimental setup, with laser wavelength 405nm and objective-lens numerical aperture 0.90. The nano-ablation formation mechanism is analysed and discussed via the thermal diffusion of sample structures.

准分子激光光束均匀技术

由于放电结构及谐振腔的限制，准分子激光光斑呈现不均的分布。介绍了各种均匀器的工作原理，从衡量光束均匀性的各项指标出发，评述分析了各种均匀方法的优缺点及适用范围。