Molybdenum containing surface complex for olefin epoxidation

Silica-supported molybdenum surface complexes were prepared by the reaction between (N=) Mo(OtBu)(3) and silica via displacement of the tert-butoxy ligands for siloxyls from the silica surface. The structure of the surface molybdenum complexes was well defined by in-situ FT-IR, elemental analysis, H-1 NMR and C-13 CP/MAS NMR techniques. The surface complexes could undergo alcoholysis reaction with CD3OD and CH3OH in the same way as free (N =) Mo(OtBu)(3) and they show high catalytic activity and selectivity in olefin epoxidation. Initial rates up to 24.9 mmol epoxide (mmol Mo)(-1) min(-1) were achieved in the epoxidation of cyclohexene using TBHP as oxidant.

热解吸-气相色谱法测定植物源挥发性有机物

以Tenax-TA、Carboxen 1000和Carbosieve SⅢ为采样管填充料,将植物源挥发性有机物吸附于采样管内,样品通过二次热解吸仪解吸后,随载气进入气相色谱仪,采用氢火焰离子化检测器(FID)测定,建立了利用二次热解吸仪与气相色谱联用技术测定植物挥发性有机物的分析方法。载气N2流速为30 mL/min,60℃下吹扫吸附管2 min,然后在250℃下解吸吸附管5 min,冷却1 min后,在275℃下解吸聚焦管3 min,样品经传输线进入气相色谱。气相色谱载气N2压力为190 kPa,FID检测器温度280℃;进样口温度225℃;初始柱温40℃,停留5 min,以2℃/min升温至120℃,保留1 min,然后以20℃/min升温至200℃,保留10 min。方法重现性好,精密度高,线性相关系数大于0.99;检出限均低于9×10-9g/L;解吸效率大于96%,适用于植物源挥发性有机物的测定。

湿地植物光合作用向水体供氧能力的试验研究

The results of the examination showed that some wetland plants' leaves and stems above the surface of water have little ability to supply water body with oxygen through roots of themselves while they are photosynthesizing. These plants are calamus(Acorus calamus), cattail(Typha angustifolia), wild rice stem(Zizania caduciflora), Cyoerus alternifokius, and water hyacinth(Eichhornia crassipes). It means that there is no relationship between these plants' photosynthesis and the breath of root cells. But duckweed(Lemna minor) has a small to raise DO 0.44mg·L -1 in average, while it is photosynthesizing during the examination. Reed(Phragmitas communis) may have a little the to provide oxygen for water body through root of itself while it is photosynthesizing. It raised DO 0.30mg·L -1 in average during the examination.

Counterions in polyelectrolyte multilayers: A vehicle for introducing functionalities

Counterions present at the surface of polyelectrolyte multilayers were utilized for the introduction of charged species into the multilayer via ion exchange. A typical polyelectrolyte multilayer film with Na+ counterions in the outermost layer was immersed in an AgNO3 aqueous solution and the rapid ion-exchange process was complete within 1 min. The silver ions thus introduced were then reduced in situ and silver nanoparticles were produced at the surface of the multilayer assembly. This example demonstrates that the counterions naturally occurring in every polyelectrolyte multilayer film can be a convenient vehicle for the introduction of various functionalities to the film.

Characterization of prolidase activity using capillary electrophoresis with tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence detection and application to evaluate collagen degradation in diabetes mellitus

A new method for prolidase (PLD, EC 3.4.13.9) activity assay was developed based on the determination of proline produced from enzymatic reaction through capillary electrophoresis (CE) with tris(2,2'-bipyridyl)ruthenium(11) [Ru(bpy)(3)(2+)] electrochemiluminescence detection (ECL). A detection limit of 12.2 fmol (S/N = 3) for proline, corresponding to 1.22 x 10(-8) units of prolidase catalyzing for 1 min was achieved. PLD activity determined by CE-ECL method was in agreement with that obtained from the classical Chinard's one. CE-ECL showed its powerful resolving ability and selectivity as no sample pretreatmentwas needed and no interference existed. The clinical utility of this method was successfully demonstrated by its application to assay PLD activity in the serum of diabetic patients in order to evaluate collagen degradation in diabetes mellitus (DM). The results indicated that enhanced collagen degradation occurred in DM.

Application of ceramic carbon materials for solid-phase extraction of organic compounds

Ceramic carbon materials were developed as new sorbents for solid-phase extraction of organic compounds using chlorpromazine as a representative. The macroporosity and heterogeneity of ceramic carbon materials allow extracting a large amount of chlorpromazine over a short time. Thus, the highly sensitive and selective determination of chlorpromazine in urine sample was achieved by differential pulse voltammograms after only 1-min extraction. The total analysis time was less than 3 min. In comparison with other electrochemical and electrochemi-luminescent methods following 1-min extraction, the proposed method improved sensitivity by about 2 and 1 order of magnitude, respectively. The fast extraction, diversity, and conductivity of ceramic carbon materials make them promising sorbents for various solid-phase extractions, such as solid-phase microextraction, thin-film microextraction, and electrochemically controlled solidphase extraction. The preliminary applications of ceramic carbon materials in chromatography were also studied.

Studies on enzymological properties of antibody elicited by meso-tetra(alpha, alpha, alpha, alpha-O-phenylacetyl benzene)porphyrin

meso-Tetra (alpha, alpha, alpha, alpha-O-phenylacetyl benzene) porphyrin was used as a complete antigen to elicit monoclonal antibody 1F2 through the immunization and cell fusion techniques. McAb 1F2 obtained was demonstrated very pure by HPLC and MALDI/TOFMS. The retention time of McAb 1F2 was 2. 63 min. The subtype of McAb 1F2 was IgG2a. The relative molecular weight was 156 678. 8. When the McAb 1F2-porphyrin was formed, the maximal absorption of the porphyrin soret region had a redshift from 408 to 416 nm and hyperchromical effect, showing that the antigen-antibody combination was rigid and intense, and the abzyme constancy was high. But compared with HRP, the activity of the abzyme was only 4. 687 5 U/mg and 1. 899 % of that of HRP. Its K-m was 20. 29 mmol/L, k(cat) 396. 82 min(-1), k(cat)/K-m. 1. 955 7 X 10(4) L . mol(-1) . min(-1).

反应挤出条件对PP-g-GMA接枝率、接枝效率和熔体流动速率的影响

用反应挤出法在聚丙烯 (PP)分子链上接枝甲基丙烯酸环氧丙酯 (GMA) ,制备功能化聚丙烯 .重点讨论了单体浓度、引发剂浓度、反应温度及物料在螺杆中的停留时间等对接枝产物 PP-g-GMA的接枝率、接枝效率和熔体流动速率的影响 .结果表明 ,PP-g-GMA接枝率与加入的单体浓度成正比 ,与引发剂浓度无关 ,反应挤出的适宜温度窗口在 1 95～ 2 3 0℃之间 ,停留时间超过 1 min后接枝率与停留时间无关 ;PP-g-GMA的熔体流动速率与单体浓度成反比 ,与引发剂的用量成正比 ,在反应温度窗口内与反应挤出温度和物料停留时间关系不大 ;单体和引发剂的浓度、反应挤出温度及物料停留时间对 PP-g-GMA的接枝效率无显著影响 .

毛细管电泳安培检测扑热息痛及其水解物

研究了各种电化学预处理条件下碳纤维电极对扑热息痛及水解物(对氨基酚)的电化学行为.确定该体系最佳预处理条件为 0.2 V电位下阳极化1 min,再于-2.0V下阴极化10s.预处理后的碳纤维伏安响应得到明显提高.运用最佳条件并在支持电解质中加入添加剂后,扑热息痛及其水解物在毛细管电泳上获得很好的分离和检测.其中扑热息痛的检测下限为 2.78pg;对氨基酚为 1.84pg.

He, Ne and Ar isotopic composition of Fe-Mn crusts from the western and central Pacific Ocean and implications for their genesis

The noble gas nuclide abundances and isotopic ratios of the upmost layer of Fe-Mn crusts from the western and central Pacific Ocean have been determined. The results indicate that the He and Ar nuclide abundances and isotopic ratios can be classified into two types: low He-3/He-4 type and high He-3/He-4 type. The low He-3/He-4 type is characterized by high He-4 abundances of 191x10(-9) cm(3.)STP(.)g(-1) on average, with variable He-4, Ne-20 and Ar-40 abundances in the range (42.8-421)x10(-9) cm(3.)STP(.)g(-1), (5.40-141)x10(-9)cm(3.)STP(.)g(-1), and (773-10976)x10(-9) cm(3.)STP(.)g(-1), respectively. The high He-3/He-4 samples are characterized by low He-4 abundances of 11.7x10(-9) cm(3.)STP(.)g(-1) on average, with He-4, Ne-20 and Ar-40 abundances in the range of (7.57-17.4)x10(-9) cm(3.)STP(.)g(-1), (110.4-25.5)x10(-9) cm(3.)STP(.)g(-1) and (5354-9050)x10(-9) cm(3.)STP(.)g(-1), respectively. The low He-3/He-4 samples have He-3/He-4 ratios (with RIRA ratios of 2.04-2.92) which are lower than those of MORB (R/R-A=8 +/- 1) and Ar-40/Ar-36 ratios (447-543) which are higher than those of air (295.5). The high He-3/He-4 samples have He-3/He-4 ratios (with R/R-A ratios of 10.4-12.0) slightly higher than those of MORB (R/R-A=8 +/- 1) and Ar-40/Ar-36 ratios (293-299) very similar to those of air (295.5). The Ne isotopic ratios (Ne-20/Ne-22 and Ne-21/Ne-22 ratios of 10.3-10.9 and 0.02774-0.03039, respectively) and the Ar-38/Ar-36 ratios (0.1886-0.1963) have narrow ranges which are very similar to those of air (the Ne-20/Ne-22, Ne-21/Ne-22, Ar-38/Ar-36 ratios of 9.80, 0.029 and 0.187, respectively), and cannot be differentiated into different groups. The noble gas nuclide abundances and isotopic ratios, together with their regional variability, suggest that the noble gases in the Fe-Mn crusts originate primarily from the lower mantle. The low He-3/He-4 type and high He-3/He-4 type samples have noble gas characteristics similar to those of HIMU (High U/Pb Mantle)- and EM (Enriched Mantle)-type mantle material, respectively. The low He-3/He-4 type samples with HIMU-type noble gas isotopic ratios occur in the Magellan Seamounts, Marcus-Wake Seamounts, Marshall Island Chain and the Mid-Pacific Seamounts whereas the high He-3/He-4 type samples with EM-type noble gas isotopic ratios occur in the Line Island Chain. This difference in noble gas characteristics of these crust types implies that the Magellan Seamounts, Marcus-Wake Seamounts, Marshall Island Chain, and the Mid-Pacific Seamounts originated from HIMU-type lower mantle material whereas the Line Island Chain originated from EM-type lower mantle material. This finding is consistent with variations in the Pb-isotope and trace element signatures in the seamount lavas. Differences in the mantle surce may therefore be responsible for variations in the noble gas abundances and isotopic ratios in the Fe-Mn crusts. Mantle degassing appears to be the principal factor controlling noble gas isotopic abundances in Fe-Mn crusts. Decay of radioactive isotopes has a negligible influence on the nuclide abundances and isotopic ratios of noble gases in these crusts on the timescale of their formation.

pCO(2) and carbon fluxes across sea-air interface in the Changjiang Estuary and Hangzhou Bay

Partial pressure of CO2 (pCO(2)) was investigated in the Changjiang (Yangtze River) Estuary, Hangzhou Bay and their adjacent areas during a cruise in August 2004, China. The data show that pCO(2) in surface waters of the studied area was higher than that in the atmosphere with only exception of a patch east of Zhoushan Archipelago. The pCO(2) varied from 168 to 2 264 mu atm, which fell in the low range compared with those of other estuaries in the world. The calculated sea-air CO2 fluxes decreased offshore and varied from -10.0 to 88.1 mmol m(-2) d(-1) in average of 24.4 +/- 16.5 mmol m(-2) d(-1). Although the area studied was estimated only 2 x 10(4) km(2), it emitted (5.9 +/- 4.0) x 10(3) tons of carbon to the atmosphere every day. The estuaries and their plumes must be further studied for better understanding the role of coastal seas playing in the global oceanic carbon cycle.

Spatial variability in biomass and production of heterotrophic bacteria in the East China Sea and the Yellow Sea

The distributions of heterotrophic bacterial abundance and production were investigated in the East China Sea and the Yellow Sea during the autumn of 2000 and spring of 2001. Bacterial abundance varied in the range 3.2-15.7 (averaging 5.7) x 10(5) and 2.3-13.6 (averaging 6.2) x 10(5) cells cm(-3) in the spring and autumn, respectively. During autumn, bacterial production (BP) (0.27-7.77 mg C m(-3) day(-1)) was on average 3 fold that in spring (0.001-2.04 mg C m(-3) day(-1)). Bacterial average turnover rate (ratio of bacterial production:bacterial biomass, mu=0.21 day(-1)) in autumn was 3 times as high as in spring (0.07 day(-1)). The ratio of integrated bacterial biomass to integrated phytoplankton biomass in the euphotic zone ranged from 4 to 101% (averaging 35%) in spring and 24 to 556% (averaging 121%) in autumn. The results indicate that the distributions of heterotrophic bacteria were controlled generally by temperature in spring and additionally by substrate supply in autumn. (C) 2010 Elsevier Ltd. All rights reserved.

社会形势预警的几种建模方法比较

Based on social survey data conducted by local research group in some counties executed in the nearly past five years in China, the author proposed and solved two kernel problems in the field of social situation forecasting: i) How can the attitudes’ data on individual level be integrated with social situation data on macrolevel; ii) How can the powers of forecasting models’ constructed by different statistic methods be compared? Five integrative statistics were applied to the research: 1) algorithm average (MEAN); 2) standard deviation (SD); 3) coefficient variability (CV); 4) mixed secondary moment (M2); 5) Tendency (TD). To solve the former problem, the five statistics were taken to synthesize the individual and mocrolevel data of social situations on the levels of counties’ regions, and form novel integrative datasets, from the basis of which, the latter problem was accomplished by the author: modeling methods such as Multiple Regression Analysis (MRA), Discriminant Analysis (DA) and Support Vector Machine (SVM) were used to construct several forecasting models. Meanwhile, on the dimensions of stepwise vs. enter, short-term vs. long-term forecasting and different integrative (statistic) models, meta-analysis and power analysis were taken to compare the predicting power of each model within and among modeling methods. Finally, it can be concluded from the research of the dissertation: 1) Exactly significant difference exists among different integrative (statistic) models, in which, tendency (TD) integrative models have the highest power, but coefficient variability (CV) ones have the lowest; 2) There is no significant difference of the power between stepwise and enter models as well as short-term and long-term forecasting models; 3) There is significant difference among models constructed by different methods, of which, support vector machine (SVM) has the highest statistic power. This research founded basis in all facets for exploring the optimal forecasting models of social situation’s more deeply, further more, it is the first time methods of meta-analysis and power analysis were immersed into the assessments of such forecasting models.

1-mm gate periphery AlGaN/AIN/GaN HEMTs on SiC with output power of 9.39 W at 8 GHz

AlGaN/AlN/GaN high electron mobility transistor (HEMT) structures with high mobility GaN channel layer were grown on 50 min diameter semi-insulating (SI) 6H-SiC substrates by metalorganic chemical vapor deposition and large periphery HEMT devices were fabricated and characterized. High two-dimensional electron gas mobility of 2215 cm(2)/V s at room temperature with sheet electron concentration of 1.044 x 10(13)/cm(2) was achieved. The 50 mm diameter HEMT wafer exhibited a low average sheet resistance of 251.0 Omega/square, with the resistance uniformity of 2.02%. Atomic force microscopy measurements revealed a smooth AlGaN surface with a root-mean-square roughness of 0.27 nm for a scan area of 5 mu mi x 5 pm. The 1-mm gate width devices fabricated using the materials demonstrated a very high continuous wave output power of 9.39 W at 8 GHz, with a power added efficiency of 46.2% and power gain of 7.54 dB. A maximum drain current density of 1300 mA/mm, an extrinsic transconductance of 382 mS/mm, a current gain cutoff frequency of 31 GHz and a maximum frequency of oscillation 60 GHz were also achieved in the same devices. (C) 2007 Elsevier Ltd. All rights reserved.