稀土三元催化剂下正辛酸缩水甘油酯-二氧化碳-环氧丙烷的三元共聚合

研究了稀土三元催化剂(三氯乙酸稀土配合物/二乙基锌/甘油)催化下的正辛酸缩水甘油酯、CO2和环氧丙烷三元共聚合。红外光谱、核磁共振和DSC结果表明,所获得的聚合物是一种新型的三元共聚物。随着反应单体中正辛酸缩水甘油酯比例的增加,所得聚合物在20℃下的断裂伸长率由二氧化碳-环氧丙烷共聚物的31.0%增大至二氧化碳-正辛酸缩水甘油酯共聚物的983.9%,相应的玻璃化转变温度由39.6℃降低至-12.3℃。所得三元共聚物中长碳链侧基单元含量为5.6%时,其断裂伸长率就已经达到481.1%,而拉伸强度仍然维持在24.9MPa的较高水平。

Facile, Efficient Copolymerization of Ethylene with Bicyclic, Non-Conjugated Dienes by Titanium Complexes Bearing Bis(beta-Enaminoketonato) Ligands

Copolymerizations of ethylene with 5-vinyl-2-norbornene or 5-ethylidene-2-norbornene under the action of various titanium complexes bearing bis(beta-enaminoketonato) chelate ligands of the type, [(RN)-N-1=C(R-2)CH=C(R-3)O](2)TiCl2 (1, R-1=Ph, R-2=CF3, R-3=Ph; 2, R-1=C6H4F-p, R-2=CF3, R-3=Ph; 3, R-1=Ph, R-2=CF3, R-3=t-Bu; 4, R-1=C6H4F-p, R-2=CF3, R-3=t-Bu; 5, R-1=Ph, R-2=CH3, R-3=CF3; 6, R-1=C6H4F-p, R-2=CH3 R-3=CF3), have been shown to occur with the regioselective insertion of the endocyclic double bond of the monomer into the copolymer chain, leaving the exocyclic vinyl double bond as a pendant unsaturation. The ligand modification strongly affects the copolymerization behaviour. High catalytic activities and efficient co-monomer incorporation can be easily obtained by optimizing the catalyst structures and polymerization conditions.

毛细管电泳电化学发光用于丙吡胺及其与血浆蛋白结合率的测定

本实验利用透析袋平衡透析、毛细管电泳Ru(bpy)32+电化学发光检测技术测定了丙吡胺和人血浆蛋白的结合率。在恒电位1.3V;进样电压10kV持续10s,分离电压15kV,运行缓冲液30mmol/L磷酸盐缓冲液(pH7.5),检测池中为5mmol/LRu(bpy)32+稀释于50mmol/L磷酸盐缓冲液(pH7.5)中等最优化的条件下,丙吡胺的检出限为10μmol/L(S/N=3)。对蛋白结合率的测定结果表明,人血浆中的药物浓度为1.6～8.2mmol/L,丙吡胺与血浆蛋白的结合是呈线性的,其线性回归方程为y=-0.07+0.93x,线性相关系数r为0.9999,丙吡胺与人血浆蛋白的结合率约为90.4%。

Label-Free Colorimetric Detection of Aqueous Mercury Ion (Hg2+) Using Hg2+-Modulated G-Quadruplex-Based DNAzymes

Mercury ion (Hg2+) is able to specifically bind to the thymine-thymine (T-T) base pair in a DNA duplex, thus providing a rationale for DNA-based selective detection of Hg2+ with various means. In this work, we for the first time utilize the Hg2+-mediated T-T base pair to modulate the proper folding of G-quadruplex DNAs and inhibit the DNAzyme activity, thereby pioneering a facile approach to sense Hg2+ with colorimetry. Two bimolecular DNA G-quadruplexes containing many T residues are adopted here, which function well in low- and high-salt conditions, respectively. These G-quadruplex DNAs are able to bind hemin to form the peroxidase-like DNAzymes in the folded state. Upon addition of Hg2+, the proper folding of G-quadruplex DNAs is inhibited due to the formation of T-Hg2+-T complex. Ibis is reflected by the notable change of the Soret band of hemin when investigated by using UV-vis absorption spectroscopy. As a result of Hg2+ inhibition, a sharp decrease in the catalytic activity toward the H2O2-mediated oxidation of 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid)diammonium salt (ABTS) is observed, accompanied by a change in solution color. Through this approach, aqueous Hg2+ can be detected at 50 nM (10 ppb) with colorimetry in a facile way, with high selectivity against other metal ions.

G-Quadruplex Aptamers with Peroxidase-Like DNAzyme Functions: Which Is the Best and How Does it Work?

Some G-quadruplex DNA aptamers have been found to strongly bind hemin to form DNAzymes with peroxidase-like activity. To help determine the most suitable DNAzymes and to understand how they work, five previously reported G-quadruplex aptamers were compared for their binding affinity and then the potential catalytic mechanism of their corresponding hemin-G-quadruplex DNAzymes was explored. Among these aptamers, a G-quadruplex named AGRO100 was shown to possess the highest hemin-binding affinity and the best DNAzyme function. This means that AGRO100 is the most ideal candidate for DNAzyme-based analysis. Furthermore, we found the peroxidase-like activity of DNAzyme to be primarily dependent on the concentration of H2O2 and independent of that of the peroxidase substrate (that is, 2,2-azino-bis(3-ethytbenzothiazoline-6-sulfonic acid)diammonium salt). Accordingly, a reaction mechanism for DNAzyme-catalyzed peroxidation is proposed. This study provides new insights into the G-quadruplex-based DNAzymes and will help us to further extend their applications in the analytical field.

Syntheses and ethylene polymerization behavior of supported salicylaldimine-based neutral nickel(II) catalysts

Two novel salicylaldimine-based neutral nickel(II) complexes, [(2,6-iPr(2)C(6)H(3))NCH(2-ArC6H3O)]Ni(PPh3)Ph (6, Ar = 2-(OH)C6H4; 8, Ar = 2-OH-3-(2,6-iPr(2)C(6)H(3)NCH)C6H3), have been synthesized, and their structures have also been confirmed by X-ray crystallography, elemental analysis, and H-1 and C-13 NMR spectra. An important structural feature of the two complexes is the free hydroxyl group, which allows them to react with silica pretreated with trimethylaluminum under immobilization by the formation of a covalent bond between the neutral nickel(II) complex and the pretreated silica. As active single-component catalysts, the two complexes exhibited high catalytic activities up to 1.14 and 1.47 x 10(6) g PE/mol(Ni)center dot h for ethylene polymerization, respectively, and yielded branched polymers. Requiring no cocatalyst, the two supported catalysts also showed relatively high activities up to 4.0 x 10(5) g PE/mol(Ni)center dot h and produced polyethylenes with high weight-average molecular weights of up to 120 kg/mol and a moderate degree of branching (ca. 13-26 branches per 1000 carbon atoms).

Facile preparation of amperometric laccase biosensor with multifunction based on the matrix of carbon nanotubes-chitosan composite

The carbon nanotubes-chitosan (CNTs-CS) composite provides a suitable biosensing matrix due to its good conductivity, high stability, and good biocompatibility. Enzymes can be firmly incorporated into the matrix without the aid of other cross-linking reagents. The composite is easy to form insoluble film in solution above pH 6.3. Based on this, a facilely fabricated amperometric biosensor by entrapping laccase into the CNTs-CS composite film has been developed. At pH 6.0, the fungi laccase incorporated into the composite film remains better catalytic activity than that dissolved in solution. The system is in favor of the accessibility of substrate to the active site of laccase, thus the affinity to substrates is improved greatly, such as 2,2'-azino-bis-(3-ethylbenzthiazoline-6-sulfonic acid) diammonium salt (ABTS), catechol, and 0, with K. values of 19.86 mu M, 9.43 mu M, and 3.22 mM, respectively. The major advantages of the as-prepared biosensor are: detecting different substrates (ABTS, catechol, and 02), possessing high affinity and sensitivity, durable long-term stability, and facile preparation procedure. On the other hand, the system can be applied in fabrication of biofuel cells as the cathodic catalysts based on its good electrocatalysis for oxygen reduction.

Surface-enhanced Raman scattering of silver-gold bimetallic nanostructures with hollow interiors

Surface-enhanced Raman scattering (SERS) activity of silver-gold bimetallic nanostructures (a mean diameter of similar to 100 nm) with hollow interiors was checked using p-aminothiophenol (p-ATP) as a probe molecule at both visible light (514.5 nm) and near-infrared (1064 nm) excitation. Evident Raman peaks of p-ATP were clearly observed, indicating the enhancement Raman scattering activity of the hollow nanostructure to p-ATP. The enhancement factors (EF) at the hollow nanostructures were obtained to be as large as (0.8 +/- 0.3)x10(6) and (2.7 +/- 0.5)x10(8) for 7a and 19b (b(2)) vibration mode, respectively, which was 30-40 times larger than that at silver nanoparticles with solid interiors at 514.5 nm excitation. EF values were also obtained at 1064 nm excitation for 7a and b(2)-type vibration mode, which were estimated to be as large as (1.0 +/- 0.3)x10(6) and (0.9 +/- 0.2)x10(7), respectively. The additional EF values by a factor of similar to 10 for b(2)-type band were assumed to be due to the chemical effect. Large electromagnetic EF values were presumed to derive from a strong localized plasmas electromagnetic field existed at the hollow nanostructures.

Syntheses and properties of polyimides derived from diamines containing 2,5-disubstituted pyridine group

A Series of novel homo- and copolyimides containing pyridine units were prepared from the heteroaromatic diamines, 2,5-bis (4-aminophenyl) pyridine and 2-(4aminophenyl)-5-aminopyridine, with pyromelltic dianhydride (PMDA), and 3,3',4,4'-biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two-step thermal imidizaton method. The poly(amic acid) precursors have inherent viscosities of 1.60-9.64 dL/g (c = 0.5 g/dL in DMAC, 30 degrees C) and all of them can be cast and thermally converted into flexible and tough polyimide films. All of the polyimides show excellent thermal stability and mechanical properties. The polyimides have 10% weight loss temperature in the range of 548-598 degrees C in air. The glass transition temperatures of the PMDA-based samples are in the range of 395-438 degrees C, while the BPDA-based polyimides show two glass transition temperatures (T(g)1 and T(g)2), ranging from 268 to 353 degrees C and from 395 to 418 degrees C, respectively. The flexible films possess tensile modulus in the range of 3.42-6.39 GPa, strength in the range of 112-363 MPa and an elongation at break in the range of 1.2-69%. The strong reflection peaks in the wide-angle X-ray diffraction patterns indicate that the polyimides have a high packing density and crystallinity.

Syntheses and properties of novel polyimides derived from 2-(4-aminophenyl)-5-aminopyrimidine

2-(4-Aminophenyl)-5-aminopyrimidine (4) is synthesized via a condensation reaction of vinamidium salts and amidine chloride salts, followed by hydrazine palladium catalyzed reduction. A series of novel homo- and copolyimides containing pyrimidine unit are prepared from the diamine and 1,4-phenylenediamine (PDA) with pyromellitic dianhydride (PMDA) or 3,3',4,4'-biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two-step thermal imidization method. The poly(amic acid) precursors had inherent viscosities of 0.97-4.38 dL/g (c = 0.5 g/dL, in DMAc, 30 degrees C) and all of them could be cast and thermally converted into flexible and tough polyimide films. All of the polyimides showed excellent thermal stability and mechanical properties. The glass transition temperatures of the resulting polyimides are in the range of 307-434 degrees C and the 10% weight loss temperature is in the range of 556-609 degrees C under air. The polyimide films possess strength at break in the range of 185-271 MPa, elongations at break in the range of 6.8-51%, and tensile modulus in the range of 3.5-6.46 GPa. The polymer films are insoluble in common organic solvents, exhibiting high chemical resistance.

水介质中丙烯酸的分散聚合

丙烯酸聚合物及其与其它水性单体的共聚物是一类非常重要的水溶性高分子化合物,具有许多优异的性能,广泛应用于环保、石油化工、造纸和食品卫生等行业[1].丙烯酸聚合物一般采用水溶液、反相悬浮及反相乳液法制备,但这些方法存在诸如反应体系粘度高,不易散热、使用不方便,由于使用有机溶剂和表面活性剂易对环境造成二次污染等问题[2].近些年,由日本率先研制开发的以水为溶剂分散型高浓度、高分子量的新型水溶性高分子产品,克服了传统合成方式和产品剂型等诸多问题,极大地拓宽了其使用领域[3~5].有关水介质中水溶性单体分散聚合的研究报道很少[6~8],而针对于丙烯酸在水介质中的研究报道则更少[9],大部分工作为专利文献.本文用分散聚合方法合成了丙烯酸分散体,初步研究了分散剂、引发剂及无机盐用量等对丙烯酸在盐水介质中分散聚合反应的影响以及对产品粒径和粒径分布的影响.1实验部分1.1试剂丙烯酸,分析纯,北京益利精细化学品有限公司,经减压蒸馏后除去阻聚剂;过硫酸铵、亚硫酸氢钠、硫酸铵等均为分析纯试剂,北京化工厂;分散剂为本实验室自制.1.2样品的制备及表征在配有冷凝管、温度计、氮气导管和搅拌器的500 mL四口圆底烧瓶中,按计算量加入丙烯...

电子反常供需型Diels-Alder反应合成2-吡啶基吡啶

电子反常供需型Diels-Alder反应(inverse electron demabd Diels-Alder reaction,IDA)因其在天然生物碱及类似物合成中的应用,在近20年来已经逐渐引起关注[1].含氮芳杂环体系1,2,4-三嗪由于其特有的缺电子特征,作为双烯体非常适于进行这类反应[2].本文利用IDA反应从3-吡啶基-5,6-二取代-1,2,4-三嗪出发,设计出一条简捷、低成本的合成路线,成功地合成出不对称取代的2,3′-联吡啶和2,4′-联吡啶.这一类化合物已被应用于药物中间体或有机配体.

石墨炉原子吸收光谱法测定蘑菇中的镉、铅

采用石墨炉原子吸收光谱法测定蘑菇中的镉、铅,以磷酸二氢铵和硝酸镁作混合基体改进剂,提高了测定的灰化温度,消除了基体干扰。方法简便,快速,准确度高。镉和铅的相对标准偏差为3.7%～6.0 %和7.3 %～7.9%;回收率为 98%～106%和 98%～104%;检出限为0.009μg g和0.032 μg g。

Capillary electrophoresis with amperometric detection of curcumin in Chinese herbal medicine pretreated by solid-phase extraction

In the present study, curcumin from Chinese herbal medicine turmeric was determined by capillary electrophoresis with amperometric detection (CE-AD) pretreated by a self-designed, simple, inexpensive solid-phase extraction (SPE) cartridge based on the material of tributyl phosphate resin. An average concentration factor of 9 with the recovery of >80% was achieved when applied to the analysis of curcumin in extracts of turmeric. Under the optimized CE-AD conditions: a running buffer composed of 15 mM phosphate buffer at a pH 9.7, separation voltage at 16 W, injection for 6 s at 9 W and detection at 1.20 V, CE-AD with SPE exhibited low detection limit as 3 - 10(-8) mol/l (SIN = 3), high efficiency of 1.0(.)10(5) N, linear range of 7(.)10(-4) -3(.)10(-6) mol/l (r = 0.9986) for curcumin extracted from light petroleum. The method developed resulted in enhancement of the detection sensitivity and reduction of interference from sample matrix in complicated samples and exhibited the potential application for routine analysis, especially in food, because a relatively complete process of sample treatment and analysis was described.

A chemiluminescence optical fiber glucose biosensor based on co-immobilizing glucose oxidase and horseradish peroxidase in a sol-gel film

An optical fiber bienzyme sensor based on the luminol chemiluminescent reaction was developed and demonstrated to be sensitive to glucose. Glucose oxidase (GOD) and horseradish peroxidase (HRP) were co-immobilized by microencapsulation in a sol-gel film derived from tetraethyl orthosilicate(TEOS). The calibration plots for glucose were established by the optical fiber glucose sensor fabricated by attaching the bienzyme silica gel onto the glass window of the fiber bundle. The linear range was 0.2-2 mmol/L and the detection limit was approximately 0.12 mmol/L. The relative standard deviation was 5.3% (n = 6). The proposed biosensor was applied to glucose assay in ofloxacin injection successfully.