Novel trichromatic phosphor codoped with two rare earth ions in a single matrix

The luminescence properties of CaBPO5: Eu, Tb phosphor and the sensitization of Ce3+ were investigated. The CaBPO5: Eu, Tb phosphors were synthesized in the ambient air and the emission spectra of Eu3+, Tb3+ and Eu2+ were Observed in the phosphor. The result shows that there is electron transfer between conjugate rare earth ions. Sensitization of Ce3+ can improve the intensity of emission of Tb3+ and Eu2+. A novel trichromatic lamp phosphor codoped with Eu3+-Tb3+ in matrix CaBPO5 is then predicted.

Preparation, characterization and photophysical properties of layered zirconium bis(monohydrogenphosphate) intercalated with rare earth complexes

Two kinds of rare earth (RE) complexes were intercalated into zirconium bis(monohydrogenphosphate) (alpha -ZrP) by exchanging the RE complexes into the p-methyoxyaniline (PMA) preintercalated compound Zr(O3POH)(2). 2PMA (alpha -ZrP . 2PMA). Powder X-ray diffraction patterns reveal that Eu(DBM)(3)phen (DBM: dibenzoylmethane, phen: 1,10-phenanthroline) and Tb(AA)(3)phen (AA: acetylacetone) intercalated into alpha -ZrP . 2PMA. This was confirmed by the UV-visible spectra of both the RE complexes and the assemblies. At the same time, the assemblies have better luminescent properties, and the fluorescent lifetimes of RE3+ in the excited state in the assemblies are much longer than those in the complexes. The stabilities of the assemblies under UV radiation are much better than those of the RE complexes.

Study of the alkylation of isobutane with n-butene over WO3/ZrO2 strong solid acid. 1. Effect of the preparation method, WO3 loading, and calcination temperature

A series of strong solid acids composed of WO3/ZrO2 were prepared. Their crystal structure, surface state, and acidity were determined by the methods of X-ray diffraction, thermal gravimetric and differential thermal analysis, temperature-programmed reduction, laser Raman, and acidity measurement. The results revealed that ZrO2 in WO3/ZrO2 existed mainly in the tetragonal phase, the addition of WO3 plays an important role in stabilizing the tetragonal phase of ZrO2, and all of the samples possessed large surface areas. WO3 in WO3/ZrO2 is mainly monolayer dispersed, and a small amount crystallized on the ZrO2 surface and partly reacted with ZrO2 to form the bond of Zr-O-W, acting as the strong solid acid center. The catalytic properties of WO3/ZrO2 strong solid;acids for alkylation of isobutane with butene at different conditions were investigated. They had a better reaction performance than other strong solid acids; a parallel relationship could be drawn between the catalytic activity and the acid amounts as well as the acidic strength of the catalysts.

Stimulated emission in the blue wavelength region from a copolymer containing PPV segment

The lasing properties of a soluble conjugated polymer, Poly[1,8-octanedioxy-2,6-dimethoxy-1,4-phenylene-1,2-ethenylene-1,2-phenylene-1,2-ethenylene-3,5-dimethoxy-1,4-phenylene] (CNMBC-Ph) in chloroform solution were investigated. The third harmonic radiation of a Nd:YAG laser was used as the pump light. The stimulated emission with a linewidth of 15 nm was observed in the blue wavelength region with the peak at 450 nm. The threshold pulse peak power was about 2.8 MW/cm(2). The energy conversion yield of the laser was estimated to be about 3.4%. The maximum peak power of the laser output pulse reached 40 kW. (C) 2000 Published by Elsevier Science S.A. All rights reserved.

Studies on the alkylation of isobutane with butene over WO3/ZrO2 strong solid acid (I) - Effect of preparation, load of WO3 and calcination temperature

A series of WO3/ZrO2 strong solid acid prepared under different conditions were studied. Their crystal structures, surface properties and acidities were determined by means of XRD, DTA-TG, H-2- TPR, Laser Raman and acidity measurements. The results revealed that ZrO2 in WO3/ZrO2 existed mainly in tetragonal phase, the addition of WO3 plays an important role to stabilize tetragonal phase of ZrO2 and thus the catalyst had a considerable surface area. WO3 in WO3/ZrO2 was dispersed and crystalized in WO3 crystalite on ZrO2 surface and partly reacted with ZrO2 to form the bond of Zr-O-W, which acts as the strong solid acid site. The catalytic properties of WO3/ZrO2 strong solid acid for alkylation of iso-butane with butene under the different conditions were investigated. They had a better reaction performance than other strong solid acids, a parallel relationship could be drawn between the catalytic activity and the amount of acid sites as well as the acidic strength of the catalysts.

Spontaneous emission properties of organic film in plane optical microcavity

The spontaneous emission properties of a single layer organic film in plane optical microcavities were studied. Optical microcavity was formed by a Tris(8-quinolinolato) aluminium (Alq) film sandwiched between a distributed Bragg reflector (DBR) and a Ag metallic reflector. Two kinds of microcavities were devised by using a different DBR structure. Compared with a Alq film, significantly spectral narrowing and intensity enhancement was observed in the two microcavities, which is attributed to the microcavity effect. The spectra characteristics of the two microcavities showed that the structure of DBR has much influence on the emission properties of a microcavity. (C) 2000 Elsevier Science S.A. All rights reserved.

WO_3/ZrO_2固体强酸催化剂上异丁烷-丁烯烷基化反应的研究Ⅲ.超细ZrO_2载体对催化剂性能的影响

制备了以超细 Zr O2 为载体的 WO3/ Zr O2 、 SO42 - / Zr O2 、 Mo O3/ Zr O2 固体强酸催化剂 ,并用 XRD、 DTA-TG、 H2 - TPR、 NH3- TPD等方法表征了其晶型结构、表面状态和酸性 .结果表明 ,超细 Zr O2 及其催化剂均主要以 T-晶相存在 ,与通常以 Zr(OH) 4为载体制备的同类催化剂相比 ,Zr O2 中的 T-晶相所占比例虽有所下降 ,但具有更大的比表面积、酸强度和对金属氧化物的负载能力 ,且酸强度随焙烧温度升高而增强 ,表明其表面状态亦有较大变化 .研究了以超细 Zr O2 为载体的固体强酸催化剂上 ,异丁烷 -丁烯的烷基化反应 ,与通常以 Zr(OH) 4为载体制得的催化剂相比 ,其具有更好的烯烃转化率 ,在烷基化产物中 ,C5 ～ C7裂解产物较多 ,使 C80的选择性有所下降

WO_3/ZrO_2固体强酸催化剂上异丁烷-丁烯烷基化反应研究(Ⅰ)──钨负载量和焙烧温度的影响

制备了系列 WO3/ Zr O2 固体强酸催化剂 ,用 XRD,DTA-TG,H2 -TPR,Raman光谱和酸性测定等方法测定其晶型结构、表面状态和酸性 .结果表明 ,WO3/ Zr O2 中的 Zr O2 基本以 T晶相存在 ,WO3对稳定 T晶相有重要作用 ,样品具有较大的表面积 .分散于 Zr O2 表面上的 WO3主要以单层分散和析出的 WO3晶粒形式存在 ,部分可能与 Zr O2 作用形成 Zr— O—W键并起强酸作用 .研究了各种实验条件下的异丁烷 -丁烯烷基化反应 .与其它固体酸相比 ,具有较高的起始活性和 i-C08选择性 ,且与酸强度和酸量有较好的对应关系

C_1桥联的茂金属化合物(Cp)CR_1R_2(Flu)MCl_2的合成及其催化烯烃聚合活性

合成了 6种单碳桥联的含芴 (Flu)茂 (Cp)基 B族茂金属催化剂 ,研究了它们催化烯烃聚合的能力 .通过 IR,1H NMR,EI-MS和元素分析对化合物进行了表征 .用所合成的茂金属化合物与 MAO所组成的催化体系对乙烯、丙烯的聚合进行了研究 .其中金属为 Ti的催化剂没有聚合活性或活性极低 .金属为 Zr的催化剂有一定的催化活性 ,用不同的催化剂得到的聚合物性质有一定的差异

Synthesis and characterization of metallocenes containing tert-butyl substituted cyclopentadienyl ligands and their activities in ethylene polymerization

The metallocene complexes ((BuC5H4)-Bu-t)(2)MCl2 (M=Ti (1a), Zr (1b), Hf (1c)) and (tBu2C5H3)(2)MCl2 (M=Ti (2a), Zr (2b), Hf (2c)) were synthesized by the react ions of Li (BuC5H4)-Bu-t and (LiBu2C5H3)-Bu-t with metal tetrachloride in THF solution. The complexes were characterized by their IR, H-1-NMR and EI-MS. The molecular structure of Ic was determined by X-ray single-crystal structure analysis. The complexes (1a similar to 2c) exhibited high activities for ethylene polymerizatin (up to 3.2x10(6) gPE/mol.h) in the presence of methylaluminoxane (MAO) at room temperature.

Preparation and application of a novel core-shell-particle-supported zirconocene catalyst

The use of functional groups bearing silica/poly(styrene-co-4-vinylpyridine) core-shell particles as a support for a zirconocene catalyst in ethylene polymerization was studied. Several factors affecting the behavior of the supported catalyst and the properties of the resulting polymer, such as time, temperature, Al/N (molar ratio), and Al/Zr (molar ratio), were examined. The conditions of the supported catalyst preparation were more important than those of the ethylene polymerization. The state of the supported catalyst itself played a decisive role in both the catalytic behavior of the supported catalyst and the properties of polyethylene (PE). IR and X-ray photoelectron spectroscopy were used to follow the formation of the supports. The formation of cationic active species is hypothesized, and the performance of the core-shell-particle-supported zirconocene catalyst is discussed as well. The bulk density of the PE formed was higher than that of the polymer obtained from homogeneous and polymer-supported Cp2ZrCl2/methylaluminoxane catalyst systems. (C) 2001 John Wiley & Sons, Inc.

Energy transfer from Ce3+ to Eu2+ and electron transfer from Ce3+ to Eu3+ in BaY2F8 : Ce, Eu systems

Phorsphors of BaY2F8 : Ce3+, BaY2F8: EU2+ and BaY2F8 : Ce, Eu were prepared by higher temperature solid reaction and their excitation, emission and diffuse reflection spectra were made. We firstly found that the competition of energy transfer from Ce3+ to Eu2+ and electron transfer from Ce3+ to EU3+ existed in CeF3 and EuF3-co-doped BaY2F8 systems. The f-f transition emission of EU2+ was increased with increasing x in systems BaY2F8 : 0. 03Ce, xEU. Ce4+ ions coexist,with Ce3+ ions and substitute Y3+ for Ce4+ in the systems BaY2F8 : Eu, Cc.

A new type of polymer-supported metallocene catalyst for ethylene polymerization

A new polymer-supported metallocene catalyst has been prepared, The polymer-supported metallocene displayed considerably high activity in ethylene polymerization, the highest being 3.62x10(7) gPE/molZr.h, the molecular weight of the polyethylene produced was Mn = 1.29x10(5). about 3-4 times those of corresponding homogeneous zirconocenes. The polymer-supported metallocene keeps the characteristics of homogeneous metallocene catalysts, and offers some features, such as adaptable to gas phase and slurry processes: easy to prepare in low cost: relatively high activity and lower MAO/Zr ratio; lower inorganic residues in the polyolefins as compared to cases of SiO2, Al2O3 or MgCl2; unitary active structure, no complex surface as with SiO2; good control of morphology of the resulting polymer.

叔丁基取代的环戊二烯基钛、锆、铪二氯化物的合成及催化乙烯聚合

(tBuC5H4 ) 2 MCl2 (M =Ti(1a) ,Zr(1b) ,Hf(1c) )和 (tBu2 C5H3 ) 2 MCl2 (M =Ti(2a) ,Zr(2b) ,Hf(2c) )可以通过单叔丁基环戊二烯基锂或双叔丁基环戊二烯基锂与MCl4 (M =Ti,Zr,Hf)在四氢呋喃中反应制备得到 ,用IR、1H NMR和EI MS对这些化合物进行了表征 .采用X光单晶结构分析测定了 (tBuC5H4 ) 2 HfCl2 的晶体结构 .六个化合物均具有一定的催化乙烯聚合活性

几种氧化物固体酸在异丁烷-丁烯烷基化反应中催化性能的比较

用 XRD、IR、NH3-TPD和 Hammett指示剂等方法对几种分子筛 (HZSM-5、HY、Hβ)和氧化物固体酸(SO2 - 4 /Zr O2 和 WO3/Zr O2 )进行了结构表征和酸性测定 ,并在相同的实验条件下比较了它们对异丁烷 -丁烯烷基化反应的催化活性和稳定性。结果表明 ,其烷基化产物中各种组分的收率有显著差异 ,催化性能优劣的次序为 :Hβ>HY>WO3/Zr O2 >SO2 - 4 /Zr O2 >HZSM-5。结合它们的基本物化性质 ,从反应机理上对催化性能的差异进行了分析 ,认为 Hβ和 HY可作为该反应的优选固体酸催化剂