Preparation of multilayer films containing pt nanoparticles on a glassy carbon electrode and application as an electrocatalyst for dioxygen reduction

In this paper, a simple route for the preparation of Pt nanoparticles is described. PtCl62- and [tetrakis-(N-methylpyridyl)porphyrinato] cobalt (CoTMPyP) were assembled on a 4-aminobenzoic acid modified glassy carbon electrode through the layer-by-layer method. The three-dimensional Pt nanoparticle films are directly formed on an electrode surface by electrochemical reduction of PtCl62- sandwiched between CoTMPyP layers. Regular growth of the multilayer films is monitored by UV-vis spectroscopy. X-ray photoelectron spectroscopy verifies the constant composition of the multilayer films containing Pt nanoparticles. Atomic force microscopy proves that the as-prepared Pt nanoparticles are uniformily distributed with average particle diameters of 6-10 nm. The resulting multilayer films containing Pt nanoparticles on the modified electrode possess catalytic activity for the reduction of dissolved oxygen. Rotating disk electrode voltammetry and rotating ring-disk electrode voltammetry confirm that Pt nanoparticle containing films can catalyze an almost four-electron reduction of O-2 to water in 0.5 M H2SO4 solution.

Simple preparation method of Pd nanoparticles on an Au electrode and its catalysis for dioxygen reduction

A simple method for the fabrication of Pd nanoparticles is described. The three-dimensional Pd nanoparticle films are directly formed on a gold electrode surface by simple electrodeposition at -200 mV from a solution of 1 M H2SO4+0.01 mM K2PdCl4. X-Ray photoelectron spectroscopy verifies the constant composition of the Pd nanoparticle films. Atomic force microscopy proves that the as-prepared Pd nanoparticles are uniformly distributed with an average particle diameter of 45-60 nm. It is confirmed that the morphology of the Pd nanoparticle films are correlated with the electrodeposition time and the state of the Au substrate. The resulting Pd-nanoparticle-film-modified electrode possesses high catalytic activity for the reduction of dissolved oxygen in 0.1 M KCl solution. Freshly prepared Pd nanoparticles can catalyze the reduction of O-2 by a 4-electron process at -200 mV in 0.1 M KCl, but this system is not very stable. The cathodic peaks corresponding to the reduction of O-2 gradually decrease with potential cycling and at last reach a steady state. Then two well-defined reduction peaks are observed at -390 and -600 mV vs. Ag/AgCl/KCl (sat.). Those two peaks correspond to a 2-step process for the 4-electron reduction pathway of O-2 in this neutral medium.

Synthesis of poly(epsilon-caprolactone)-b-poly(gamma-benzyl-L-glutamic acid) block copolymer using amino organic calcium catalyst

A biodegradable two block copolymer, poly(epsilon-caprolactone)-b- poly(gamma-benzyl-L-glutamic acid) (PCL-PBLG) was synthesized successfully by ring-opening polymerization of N-carboxyanhydride of gamma-benzyl-L-glutamate (BLG-NCA) with aminophenyl-terminated PCL as a macroinitiator. The aminophenethoxyl-terminated PCL was prepared via hydrogenation of a 4-nitrophenethoxyl-teminated PCL, which was novelly obtained from the polymerization of c-caprolactone (CL) initiated by amino calcium 4-nitrobenzoxide. The structures of the block copolymer and its precursors from the initial step of PCL were confirmed and investigated by H-1 NMR, FT-IR, GPC, and FT-ICRMS analyses and DSC measurements.

Syntheses and crystal structures of mononuclear rhodium hydrido complexes from the reactions of [Rh(H)(2)(PPh3)(2)(EtOH)(2)]ClO4 with various nitrogen ligands

Reactions of the Rh hydrido complex [Rh(H)(2)(PPh3)(2)(EtOH)(2)]ClO4 (1) With nitrogen ligands such as 2-(4-thiazolyl)benzimidazole (tbz). pyridazine (pdz), imidazole (im) and pyrimidine (pmd) in CH,Cl, afforded Various mononuclear Rh hydrido complexes, [Rh(H)(2)(PPh3)(2)(tbz)]CIO4 (2), [Rh(H)(2)(PPh3)(2)(pdZ)(2)]ClO(4)(.)2CH(2)Cl(2) (3). [Rh(H)Cl(PPh3)(2)(pdz)(2)](ClO4CH2Cl2)-C-. (4). [Rh(H)(2)(PPh3)(2)(im)(2)]ClO(4)(.)2CH(2)Cl(2) (5). [Rh(H)Cl(PPh3)(2)(im)(2)](ClO4CH2Cl2)-C-. (6). [Rh(H)(2)(PPh3)(2)(pmd)(2)](ClO4CH2Cl2)-C-. (7) and the Rh non-hydrido complex [RhCl2(pmd)(4)]ClO4 (8). The Rh complexes 2. 3, 5 and 6 were crystallographically characterized. The formation process was monitored by H-1 NMR and UV-Vis spectra. In all the Rh hydrido complexes, the Rh atom is coordinated by two PPh3. ligands in trans-positions and two nitrogen ligands in the cis-positions. The remaining sites Lire occupied by one or two hydride atoms to form a saturated 18-electron framework in a slightly distorted octahedral geometry. For complex 2 an appreciable inter-molecular pi interaction is observed between planes of tbz and PPh3 ligands, while an intra-molecular hydrogen bonding interaction between C-H and Cl atoms is found in complex 6.

Application of ionic liquids in organic reactions

Room-temperature ionic liquids are good solvents for a wide of organic, inorganic and organometallic compounds. Typically consisting of nitrogen-containing organic cations and inorganic anions, they are easy to recycle, nonflammable, and have no detectable vapor pressure. More recently, ionic liquids have been found to be excellent solvents for a number of chemical reactions, e. g. hydrogenation, alkylation, epoxidation, Heck-vinylation, Suzuki cross-coupling reactions and enzyme catalyzed organic reactions. This paper focuses on the recent development of using ionic liquids as solvents for transition metal and enzyme catalyzed reactions.

Solvent-dependent formation of di- and trinuclear rhodiurn and iridium complexes bridged by N,N '-donor ligands

Reactions of Rh and Ir hydrido complexes. [Rh(H)(2)(PPh3)(2)(solv)(EtOH)]ClO4 (solv = Me2CO, 1a; EtOH, 1b) and [Ir(H)(2)(PPh3)(2)(Me2CO)(2)]BF4 (2), with various N,N'-donor bridging ligands, such as pyrazine (pyz), 4,4'-trimethylenedipyridine (tmdp) and di(4-pyridyl) disulfide (dpds), in some solvents were examined, and their reaction products were characterized by X-ray crystal structure analysis. IR, H-1 NMR and UV-vis spectra. Rh hydrido complexes, la or 1b, formed a dinuclear Rh complex, [Rh-2(PPh3)(2) {(eta(6)-C6H5PPh2}(2)] (ClO4)(2).6CH(2)Cl(2) (3.6CH(2)Cl(2)), in dichloromethane with a reductive elimination of hydrogen. The reactions of 1a or 1b with the pyz ligand in dichloromethane and tetrahydrofuran gave triangular Rh-3 complexes, [Rh-3(PPh3)(6)(pyz)(3)](ClO4)(3).CH2Cl2 (5.CH2Cl2) and [Rh-3(PPh3)(6)(pyz)(3)](ClO4)(3).EtOH (5.EtOH), respectively, in contrast to the formation of a dinuclear Rh hydrido complex, [Rh-2(H)(4)(PPh3)(4)(Me2CO)(2)(pyz)](ClO4)(2).EtOH A-EtOH). in acetone. The reactions of la or 1b with the tmdp ligand in dichloromethane and 3-methyl-2-butanone also afforded dinuclear Rh complexes, [Rh-2(PPh3)(4)(tmdp)(2)](ClO4)(2) (6) and [Rh-2(PPh3)(4)(tmdp)(2)](ClO4)(2).4MeCOCHMe(2) (6.4MeCOCHMe(2)), respectively. On the other hand, Ir hydrido complex 2 reacted with pyz and dpds ligands in dichloromethane to afford dinuclear Ir complexes, [Ir-2(H)(4)(PPh3)(4)(Me2CO)(2)(pyz)]- (BF4)(2).3CH(2)Cl(2) (7.3CH(2)Cl(2)) and [Ir-2(H)(4)(PPh3)(4)(dpds)(2)](BF4)(2).3CH(2)Cl(2).H2O (8.3CH(2)Cl(2).H2O), respectively, without any reductive elimination of hydrogen. Based on structural studies in solution and in the solid state. it was demonstrated that various Rh and Ir complexes were selectively produced depending on the choice of solvents and N,N'-donor bridging ligands.

Synthesis of a novel graft-like copolymer of syndiotactic polystyrene with polybutadiene

A novel graft-like copolymer of syndiotactic polystyrene (sPS) with polybutadiene (PB) was synthesized by polymerization of styrene in a toluene solution of PB using the cyclopentadiene titanium trichloride (CpTiCl3)/methylaluminoxane (MAO) catalytic system. The effect of PB on the crystallization behavior of the copolymer was investigated by differential scanning calorimetry and wide angle X-ray diffraction. Hydrogenation of the sPS/PB copolymer with p-toluenesulfonyl hydrazide afforded a PE-like copolymer.

Synthesis and X-ray crystal structure of [(eta(5)-C5H5)Sm(mu-OC20H20N2O)](2)(mu-THF)(THF)(2): Mono(cyclopentadienyl)lanthanide complex bearing a C-2-symmetric tetradentate Schiff-base ligand

Cp2SmCl(THF) reacts with 0.5 equivalent disodium salts of trans-(+/-)-N,N'-bis(salicylidene)-1,2-cyclohexanediamine give the title complex [(eta(5)-C5H5)Sm(mu-OC20H20N2O)](2)(mu-THF)(THF)(2) (1). X-ray crystal determination shows that the molecule is a dimer, in which two (eta(5)C(5)H(5))Sm(mu-OC20H20N2O) units are connected via a THF oxygen and two bridging oxygen atoms of Schiff base ligands. The average Sm-C distance is 2.78(7) Angstrom, while those of Sm-O (bridging THF oxygen) and Schiff base oxygens are 2.79(3) and 2.43(4) Angstrom; respectively. (C) 1998 Elsevier Science Ltd. All rights reserved.

Ansa-metallocene derivatives .2. Syntheses and structures of tetramethyldisiloxandiyl bis(1-indenyl and tetrahydroindenyl) zirconium dichlorides

The ansa-zirconocene derivative tetramethyldisiloxandiyl bis(1-indenyl) zirconium dichloride (1) has been prepared by the reaction of the dilithium salt of 1,3-bis(l-indenyl) tetramethyldisiloxane with ZrCl4 . 2THF, After catalytic hydrogenation, the corresponding tetrahydroindenyl complex (2) has been formed. Both 1 and 2 have been shown by H-1 NMR spectra to be the mixture of the cis(meso) and trans(rac) isomers, The pure trans isomers 1(l), 2(l) and cis isomer 2(c) were obtained by recrystallization, The crystal structures of 1(l) and 2(c) were determined by X-ray diffraction. Both crystals of 1(l) and 2(c) are monoclinics, belonging to space groups P2(1)/n(1(l)) and P2(1)/c(2(c)). In the unit cell of 2(c), one of the six-membered rings of the tetrahydroindenyl Ligands has two different conformations which have the same probabilities.

SYNTHESES AND CHARACTERIZATION OF [(MU-CF3CO2)(2)LN(MU-CF3CHO2)ALR(2)CENTER-DOT-2THF](2) AND THEIR CATALYTIC ACTIVITIES FOR POLYMERIZATION OF SOME POLAR MONOMERS

Three new bimetallic complexes were synthesized and crystalized by reactions of (CF3CO2)(3)Ln With R(1) AlR(2)(Ln=Nd and Y, R(1)=H, R=i-C4H9; Ln=Eu, R=R(1)=C2H5) in tetrahydrofuran solution, and their crystal structures were determined using a X-ray diffraction method. The structures and the questions on valence state and noncoplanarity in the structures were confirmed and cracked by means of H-1 NMR and C-13 NMR spectra, especially by C-13-H-1 COSY 2D NMR technique. A general formula of molecules of the three rare earth complexes was defined as follows: [(mu-CF3CO2)(2)Ln(mu-CF3CHO2)AlR(2) . 2THF](2) A mechanism on the formation of the new complexes was also proposed through the following five steps: alkylating, beta-elimination (or hydrogenation), hydrogen transfer, linkage and association. Both Y-Al and Eu-Al complexes function as a catalyst in polymerization of MMA and ECH. The polymer obtained from the first monomer is mainly syndiotactic chain structure and the polymerization of the last monomer shows higher catalytic activity. The Y-Al complex also capable of ring-opening polymerization of THF in case of adding-vary small amount of ECH and a oxonium ion mechanism of THF polymerization was suggested from the analysis of THF polymer terminal.

SYNTHESIS, PROPERTIES AND MOLECULAR-STRUCTURE OF 5-COORDINATE N,N-DIBENZYLDITHIOCARBAMATE COMPLEXES OF TITANOCENE, ZIRCONOCENE AND HAFNOCENE

The five complexes (RC5H4)2M(S2CNBz2)Cl (R = H, CH3; M = Ti, Zr, Hf; Bz = CH2C6H5) have been prepared by the reaction of (RC5H4)2MCl2 with anhydrous sodium salts of dibenzyldithiocarbamate in refluxing CH2Cl2. These complexes have been characterized by elemental analysis, IR and H-1 NMR. X-ray crystal structure determination of Cp2Zr(S2CNBZ2)Cl shows the molecule has a five-coordinate bent metallocene geometry in which the zirconium atom is attached to two eta-5-C5H5 groups, one bidentate dibenzyldithiocarbamate ligand and one chlorine [Zr-Cl, 2.549(1) angstrom; Zr-S, 2.734(1), 2.667(1); Cl-Zr-S, 137.6(1)-degrees and 73.3(1)-degrees; S-Zr-S, 64.3(1)-degrees]. The catalytic system Cp2Ti (S2CNBZ2)Cl-NaH exhibits high initial catalytic activity of hydrogenation of hexene-1 under mild conditions.

SYNTHESIS OF ALKALI-METAL HYDRIDES USING LANTHANIDE TRICHLORIDE-NAPHTHALENE AS CATALYST UNDER MILD CONDITIONS

The hydrogenation of alkali metals using lanthanide trichloride and naphthalene as catalyst has been studied. LnCl3(Ln = La, Nd, Sm, Dy, Yb) and naphthalene can catalyze the hydrogenation of sodium under atmospheric pressure and 40-degrees-C to form sodium hydride. The activities of lanthanide trichlorides are in the following order: LaCl3 > NdCl3 > SmCl3 > DyCl3 > YbCl3. Although lithium proceeds in the same catalytic reaction, the kinetic curve of the lithium hydrogenation is different from that of sodium. Lanthanide trichlorides display no catalytic effect on the hydrogenation of potassium in presence of naphthalene. The mechanism of this reaction has been studied and it is suggested that the anion-radical of alkali metal naphthalene complexes may be the intermediate for the hydrogenation of alkali metals and the function of LnCl3 is to catalyze the hydrogenation of the intermediate. The products are porous solids with high specific surface area (83 m2/g for NaH) and pyrophoric in air. They are far more active than the commercial alkali metal hydrides. The combination of these hydrides with some transition metal complexes exhibits high catalytic activity for the hydrogenation of olefins.

SYNTHESIS OF TETRAPHENYLBUTADIENE LANTHANIDE METALLACYCLES

The cyclic derivatives of transition metals have been extensively investigated in recent years since they are believed to serve as key intermediates in various homogeneous catalytic processes of olefine and alkyne metathesis. The synthesis of the title compounds has not been reported before.

加氢反应器壁原子氢分布的在线、实时、无损检测新技术

为了在线、实时、无损检测高温高压条件下运行的加氢反应器的多层器壁中原子氢的渗透速率和在任何指定剖面上的体浓度分布，发展了一种新型的检测技术．介绍了检测仪的结构设计及其特征。

Preparation of lanthanide hydrides of nanometric size by the catalytic method

Rare-earth metals were hydrogenated in the presence of TiCl4 catalyst in tetrahydrofuran (THF) at 45 degreesC under normal pressure. Transmission electron micrographs showed that the re. sulting lanthanide hydrides were in the form of nanoparticles. The rate of hydrogenation decreased with increasing atomic number of the rare-earth elements.