SYNTHESIS AND PHOTOCHROMISM IN SOLUTION OF PHENOXYNAPHTHACENEQUINONE DERIVATIVES

Two new phenoxynaphthacenequinone derivatives, 6-[4-(2-(4-hydroxyphenyl)isopropyl)phenoxy] -5,12-naphthacenequinone (7) and 6-[4-(potassium sulfophenylazo)phenoxy]-5,12-naphthacenequinone (8), were synthesized, and their photochromism in solution was investigated and compared with that of 6-phenoxy-5,12-naphthacenequinone (1). On the basis of the spectral data and the selective irreversible reaction of ammonia with the colored phenoxy-ana-naphthacenequinone, the concentrations of the ana forms at the photostationary state (PSS), achieved by 365 nm UV irradiation, and the molar extinction coefficients of the pure ana forms at 481-482 nm of compounds 1, 7 and 8 in dimethylsulfoxide (DMSO) were found to be 83 mol.% and 1.70x10(4) mol(-1) dm(3) cm(-1), 82 mol.% and 1.62x10(4) mol(-1) dm(3) cm(-1) and 16 mol.% and approximately 1.34x10(4) mol(-1) dm(3) cm(-1) respectively; the absorption spectra of the colored ana forms of 7 and 1 in DMSO were estimated; the rate;constants of photoconversion induced by 365 nm light were obtained. The results show the strong effect of the structure of the phenoxynaphthacenequinones on their photochromism in solution. In addition to DMSO solution, compound 7 exhibited normal photochromism in toluene, benzene, chloroform and a DMSO-ethanol mixed solvent, but not in dimethylformamide (DMF) in which a photoinduced reaction occurred between 7 and DMF or impurities.

SYNTHESES AND CRYSTAL-STRUCTURES OF (ETA-5-C5H5)3LN(THF) (LN=CE, ER)

Brown crystalline tricyclopentadienyl cerium tetrahydrofuranate (THF) complex (eta5-C5H5)3Ce(THF) was prepared by the reaction of (NH4)2Ce(NO3)6 with sodium cyclopentadienide (C5H5Na) in THF at molar ratio of 1:6. ErCl3.4THF reacts with potassium cyclooct

CALCULATIONS FOR THE VIBRATION FREQUENCIES OF THE O-H...O BOND IN KH2PO4 BY A SEMIEMPIRICAL METHOD

The frequencies of the stretching vibration and the bending vibration of the 0-H ... 0 bond in potassium dihydrogen phosphate have been calculated by means of two semiempirical formulae with three parameters. The calculated results can give satisfactory explanation for the experimental spectra of the potassium dihydrogen phosphate crystal. The parameters used in the calculations may be related to the chemical bonding and the charge distribution about the two oxygen atoms of the 0-H ... 0 bond system.

WATER-SOLUBLE AND AMPHIPHILIC POLYMERS .11. GRAFT-POLYMERIZATION OF ACRYLIC-ACID ON POLY(VINYL ALCOHOL)

The graft polymerization of acrylic acid(AA) on poly(vinyl alcohol) (PVAL) has been investigated by using either potassium persulfate (KPS) or ceric ammonium nitrate(CAN) as an initiator. In the case of KPS initiation, the formation of the graft polymer always lags behind the homopolymer formation. The graft polymer is separated by acetone, and the increase of reaction temperature favors the homopolymer formation at the early stage. In the case of CAN initiation, graft polymers with a high PAA content can hardly be obtained when the polymerization is performed under nitrogen and at < 0.06 mol/L HNO3 concentration. It has been found that incorporation of a small amount of oxygen in a protective nitrogen gas accelerates markedly the graft polymerization, and that the resulting graft polymers can not be separated by acetone precipitation technique in most cases. The Dalian nitrogen(containing 0.7% oxygen) is a good protective gas for CAN-initiated PVAL-AA graft polymerization.

AMPEROMETRIC FLOW-INJECTION ANALYSIS OF HYDRAZINE BY ELECTROCATALYTIC OXIDATION AT COBALT TETRAPHENYLPORPHYRIN MODIFIED ELECTRODE WITH HEAT-TREATMENT

Chemically modified electrodes prepared by treating the cobalt tetraphenylporphyrin modified glassy-carbon electrode at 750-degrees (HCME) are shown to catalyze the electrooxidation of hydrazine. The oxidation occurred at +0.63 V vs. Ag/AgCl (saturated potassium chloride) in pH 2.5 media. The catalytic response is evaluated with respect to solution pH, potential scan-rate, concentration dependence and flow-rate. The catalytic stability of the HCME is compared with that of the cobalt tetraphenylporphyrin adsorbed glassy-carbon electrode. The stability of the HCME was excellent in acidic solution and even in solutions containing organic solvent (50% CH3OH). When used as the sensing electrode in amperometric detection in flow-injection analysis, the HCME permitted sensitive detection of hydrazine at 0.5 V. The limit of detection was 0.1 ng. The linear range was from 50 ng to 2.4-mu-g. The method is very sensitive and selective.

CYCLIC VOLTAMMETRIC AND SPECTROELECTROCHEMICAL STUDIES OF COPPER IN ALKALINE-SOLUTION

The behaviour of the electroplated copper film electrode on tin oxide/glass or glassy carbon surface was studied in potassium hydroxide medium by cyclic voltammetry and in situ transmission spectroelectrochemistry. The results indicate that the electroplated copper film electrode is similar to a copper electrode and cyclic voltammetry with this electrode affords more resolution. The anodic peaks were found to correspond successively to the adsorption of oxygen, the formation of a surface layer of Cu2O, the formation of a surface layer of Cu(OH)2 or CuO and formation of a thick multilayer film of CuO. This is the first time it has been proposed that a surface layer of Cu(OH)2 or CuO is formed from the oxidation of the surface layer of Cu2O. Similarly, a clear interpretation is presented that the cathodic peaks correspond successively to the reduction of CuO to Cu2O, the reductions of Cu2O to Cu and the soluble Cu(II) species to Cu. On the other hand, a shoulder peak related to the chemical transformation of Cu(OH)2 to CuO was first observed.

SYNTHESIS AND CRYSTAL-STRUCTURE OF A NEW LANTHANIDE CYCLOOCTATETRAENE COMPLEX (ETA-8-C8H8)ER(MU-ETA-8-C8H8)K(MU-ETA-8-C8H8)ER(MU-ETA-8-C8H8)K(THF)4

The tetranuclear nearly-linear complex (eta-8-C8H8)Er(mu-eta-8-C8H8)K(mu-eta-8-C8H8)Er(mu-eta-8-C8H8)K(THF)4 (THF = tetrahydrofuran) is first synthesised by the reaction of benzylcyclopentadienyl erbium dichloride (PhCH2C5H4)ErCl2.3THF with cyclooctatetraenyl potassium K2C8H8 in 1:1 molar ratio in THF; a single crystal X-ray study has shown that the complex has the tetralayer-sandwich structure and that the adjacent Er3+ and K+ ions are bridged by eta-8-cyclooctatetraenyl group.

SYNTHESIS AND STRUCTURE OF (ETA-5-C5H5)2YB.DME

(eta-5-C5H5)2YbCl.THF reacts with an equivalent molecular quantity of K(2,4-C7H11) (2,4-dimethyl pentadienyl potassium), and treatment of the product with DME yields (eta-5-C5H5)2Yb.DME. The crystal of (eta-5-C5H5)2Yb.DME belongs to the orthorhombic space group Fdd2 with a = 13.678(4) angstrom, b = 23.255(6) angstrom, c = 9.192(2) angstrom and Z = 8. The crystal parameters are found to differ from previously reported data.

SYNTHESIS OF ALKALI-METAL HYDRIDES USING LANTHANIDE TRICHLORIDE-NAPHTHALENE AS CATALYST UNDER MILD CONDITIONS

The hydrogenation of alkali metals using lanthanide trichloride and naphthalene as catalyst has been studied. LnCl3(Ln = La, Nd, Sm, Dy, Yb) and naphthalene can catalyze the hydrogenation of sodium under atmospheric pressure and 40-degrees-C to form sodium hydride. The activities of lanthanide trichlorides are in the following order: LaCl3 > NdCl3 > SmCl3 > DyCl3 > YbCl3. Although lithium proceeds in the same catalytic reaction, the kinetic curve of the lithium hydrogenation is different from that of sodium. Lanthanide trichlorides display no catalytic effect on the hydrogenation of potassium in presence of naphthalene. The mechanism of this reaction has been studied and it is suggested that the anion-radical of alkali metal naphthalene complexes may be the intermediate for the hydrogenation of alkali metals and the function of LnCl3 is to catalyze the hydrogenation of the intermediate. The products are porous solids with high specific surface area (83 m2/g for NaH) and pyrophoric in air. They are far more active than the commercial alkali metal hydrides. The combination of these hydrides with some transition metal complexes exhibits high catalytic activity for the hydrogenation of olefins.

SYNTHESES AND CRYSTAL-STRUCTURES OF TRIINDENYLLANTHANIDE COMPLEXES (ETA-5-C9H7)3LN.OC4H8 (LN=ND,GD,ER)

The complexes named in the title (eta-5-C9H7)3Ln.OC4H8 (Ln = Nd, Gd, Er) were synthesized by the reaction of anhydrous lanthanide trichlorides with indenyl potassium and cyclooctadienyl potassium (1:2:1 molar ratio) in THF. The complexes were characterized by elemental analysis, infrared and H-1-NMR spectroscopy, and mass spectrometry. In addition, the crystal structures of (eta-5-C9H7)3Nd.OC4H8 (1) and (eta-5-C9H7)3Gd.OC4H8 (2) were determined by an X-ray diffraction study. Complexes 1 and 2 belong to hexagonal space group P6(3) with unit cell parameters a = b = 11.843(3), c = 10.304(4) angstrom, V = 1251.7(9) angstrom-3, D(c) = 1.49 g.cm-3, Z = 2 for 1, and a = b = 11.805(2), c = 10.236(2) angstrom, V = 1235.4(6) angstrom-3 D(c) = 1.54 g.cm-3, Z = 2 for 2. The structures were solved by Patterson and Fourier techniques and refined by least-squares to final discrepancy indices of R = 0.049, R(w) = 0.053 using 925 independent reflections with I greater-than-or-equal-to 3-sigma(I) for 1, and R = 0.023, R(w) = 0.025 using 1327 independent reflections with I greater-than-or-equal-to 3-sigma(I) for 2. Coordination numbers for Nd3+ and Gd3+ are 10; the average bond lengths Nd-O and Gd-O are 2.557(21) and 2.459(13) angstrom, respectively. The structural studies showed the complexes to have 3-fold symmetry, but the THF molecule has no such symmetry; consequently the arrangement of carbon atoms in the THF molecule are disordered.

Antioxidative principals of Jussiaea repens: an edible medicinal plant

Jussiaea repens L. (JRL) is an edible medicinal plant and is also used as a vegetable by the local people in southwestern China. The crude extract and its four fractions derived from JRL were evaluated for the 1,1-diphenyl-2-picrylhydrazyl radical-scavenging ability, hydroxyl radical-scavenging capacity and the potassium ferricyanide reduction property. The ethyl acetate-soluble fraction (EAF) and EAF6 (a subfraction derived from EAF) were the most valuable fraction and subfraction, respectively. Furthermore, bioactivity-guided chromatographic fractionation revealed that three pure compounds greatly contributed to the antioxidant activities. Qualitative and quantitative analyses of the major antioxidant constituents in the extract were systematically conducted by NMR, mass spectral analyses and RP-HPLC. The result demonstrated that rosmarinic acid (2.00 mg g(-1) JRL dry weight) quercetin 3-O-beta-D-glucopyranoside (9.88 mg g(-1) JRL dry weight), and kaempferol 3-O-beta-D-glucopyranoside (1.85 mg g(-1) JRL dry weight) were the major antioxidative constituents in JRL. These compounds are reported for the first time from this plant.

Evaluation of antioxidant property of extract and fractions obtained from a red alga, Polysiphonia urceolata

Antioxidant activity (AA), total phenolic content, and reducing power of the crude extract, fractions, and subfractions derived from a red alga, Polysiphonia urceolata, were evaluated and determined. The antioxidative activity was measured using the alpha,alpha-diphenyl-beta-pierylhydrazyl (DPPH) radical scavenging assay and the P-carotene-linoleate assay systems, and compared with that of butylated hydroxytoluene (BHT), gallic acid (GA), and ascorbic acid (AscA). The results showed that the crude extract and the ethyl acetate-soluble fraction exhibited higher AA than BHT in the DPPH assay model, at all of four concentration levels tested (from 0.4 to 50 mu g/ml), while, in the beta-carotene-linoleate assay system, the crude extract and the ethyl acetate-soluble fraction exhibited similar or, in most cases, higher AA than GA and AscA at the same concentrations (from 10 to 200 mu g/ml). The ethyl acetate-soluble fraction was further fractionated into seven subfractions F1-F7 by silica gel vacuum liquid chromatography. F1 was found to be the most effective subfraction in both assay systems. The total phenolic content and reducing power were determined using the Folin-Ciocalteu and the potassium ferricyanide reduction methods, respectively. Statistical analysis indicated a significant association between the antioxidant potency and total phenolic content as well as between the antioxidant potency and reducing power. (c) 2005 Elsevier Ltd. All rights reserved.

长白山火山成因—物理机制和化学演化

This thesis is one of the contributions to NSFC project, “The Changbaishan Volcanism and its Links to the Northeast Asia Tectonic System”. The thesis presents our most recent works on Changbaishan Volcanism, on two aspects as (1) the chemical evolution of the Cenozoic volcanism and the physical links of magma genesis, (2) the Holocene activity of the Tianchi Volcano and risks of potential eruption. 1. Chemical evolution and physical links to the Changbaishan Volcanism Physical links to the Chanbaishan Volcanism, just like origins of most of the volcanisms in eastern China, has long been an enigma. A large scale of volcanic activity has dominated many places of eastern China in Meso-Cenozoic. Activity of these volcanisms in eastern China covers several quite different blocks, covers variety of tectonics, and covers a period of time over 200 million years. Such a large-scale and long-lived volcanism in a continental area challenges our knowledge on dynamics of the Earth’s interior. Some works on “Diwa” hypothesis and “lithospheric thinning” hypothesis present possible links between volcanisms and dynamic evolutions of the earth’s interior, but still cannot interpret where are the sources of the heat and fluid, which are essential to the volcanisms. Based on the study of this thesis, we suggest that dynamics of the deep subduction of western Pacific Plate is the critical factor to the Changbaishan Volcanism and volcanisms in NE China, and maybe even essential to most of the Meso-Cenozoic volcanisms in eastern China. In NE China, stagnant slabs flatted in the mantle transition zone (MTZ, ca. 660 km deep) transport and release significant hydrous fluid to the upper mantle. Metamorphism of the deep-subducted slabs and hence a series of mineral phases play an important role in the water transport, exchange, restore, and release. Dehydrated fluid of the wet slab ascending from the MTZ fertile the upper mantle, and also provide upward heat flow which is essential to the magma genesis. Then magma and volcanism occur with the deep subduction from Mesozoic to mordern time in eastern China. To discribe the exact chemical characteristics of the deep subduction releated volcanics is very difficult, because few researches has contributed to the chemical behaviors of fluid and trace elments in the very deep interior of the Earth, such 660 km deep, 410km or 350km where the fluid may ascend and react. However we can still find some chemical characteristics of oceanic subduction. Basalts of the Changbaishan Volcanism have siginficant characteristics of potassium rich, and even can be called a potassic igneous province. If there are only two possible ways, recycled continentical crust or oceanic crust, to fertile the mantle potossium element as we know now, it’s easy to attribute this to the deep-subducted of the west Pacific Plate. To the eastern China, fluid inclusions in mantle xenoliths from the Cenozic basalts also reveal potassium-rich characteristics. This reveals that the same potassium feritle agents may occur in the mantle sources of eastern China. 2. Holocene activiy of the Tianchi Volcano As one of the large volcanic center and complex volcanic cone, the Tianchi Volcano is a dangerous active volcano, with several Holocene eruptions. Among these eruptions, the Millennium Eruption is regardede as one of the biggist eruptions in the world in the last 2000 years. To estimate the potential danger of volcanic eruption, we discuss two essential factors, as (i) volcanic history of Holocene eruptions, including volcanic geolgy, chronnology and chemistry, (ii) state, evolution and relationship of the magma chambers in mantle and crust beneath the Tianchi Volcano.

班公湖带多不杂超大型富金斑岩铜矿床的成岩成矿年代学、岩石学及高氧化岩浆¬流体-成矿作用

Duobuza copper deposit, newly discovered typical gold-rich porphyry copper deposit with superlarge potential, is located in the Tiegelong Mesozoic tectonic -magmatic arc of the southern edge of Qiangtang block and the northern margin of Bangonghu-Nujiang suture. Quartz diorite porphyrite and grandiorite porphyry, occurred in stock, are the main ore-bearing porphyries. As the emplacement of porphyry stock, a wide range of hydrothermal alteration has developed. Within the framework of the ore district, abundant hydrothermal magnetite developed, and the relationship between precipitation of copper and gold and hydrothermal magnetite seems much close. Correspondingly, a series of veinlets and network veinlets occurred in all alteration zones. Therefore, systematic research on such a superlarge high-grade Duobuza gold-rich porphyry copper deposit can fully revealed the metallogenic characteristics of gold-rich porphyry copper deposits in this region, establish metallogenetic model and prospecting criteria, and has important practical significance on the promotion of regional exploration. In addition, this research on it can enrich metallogenic theory of strong oxidation magma-fluid to gold-rich porphyry copper deposit, and will be helpful to understand the metallogenic characteristics in early of subduction of Gangdese arc stages and its entire evolution history of the Qinghai-Tibet Plateau, the temporal and spatial distribution of ore deposits and their geodynamics settings. Northern ore body of Duobuza copper deposit have been controlled with width (north-south) about 100 ~ 400 m, length (east-west) about 1400 m, dip of 200 °, angle of dip 65 °~ 80 °. And controlled resource amount is of 2.7 million tons Cu with grade 0.94% and 13 tons Au with 0.21g/tAu. Overall features of ore body are large scale, higher grade copper, gold-rich. Ore occurred in the body of granodiotite porphyry and quartz diorite porphyrite and its contact zone with wall rock. Through the detailed mapping and field work studies, some typies of alteration are identificated as follows: albitization, biotititation, sericitization, silication, epidotization, chloritization, carbonatization, illitization, kaolinization and so on. The range of alteration is more than 10km2. Wall alteration zone can be divided into potassic alteration, moderate argillization alteration, argillization, illite-hydromuscovite or propylitization from ore-bearing porphyry center outwards, but phyllic alteration has not well developed and only sericite-quartz veins occurred in local area. Moreover, micro-fracture is development in ore district , and correspondingly a series of veinlets are development as follows: biotite vein (EB type), K-feldspar-biotite-chalcopyrite-quartz vein, magnetite-antinolite-K-feldspar vein, quartz-chalcopyrite-magnetite veins (A-type), quartz-magnetite-biotite-K-feldspar vein, chalcopyrite veinlets in potassic alteration zone; (2) chalcopyrite occurring in the center vein–quartz vein (B type), chalcopyrite veinlets, chalcopyrite-gypsum vein in intermediate argillization alteration; (3) chalcopyrite- pyrite-quartz vein, pyrite-quartz vein, chalcopyrite-gypsum veins, quartz-gypsum- molybdenite-chalcopyrite vein in argillization alteration; (4) gypsum veins, quartz-(molybdenite)-chalcopyrite vein, quartz-pyrite vein, gypsum- chalcopyrite vein, potassium feldspar veinlets, Carbonate veins, quartz-magnetite veins in the wall rock. In short, various veins are very abundant within the framework of the ore district. The results of electronic probe microscopy analysis (EMPA) indicate that Albite (Ab 91.5~99.7%) occurred along the rim of plagioclase phenocryst and fracture, and respresents the earliest stages of alteration. K-feldspar (Or 75.1~96.9%) altered plagioclase phenocryst and matrix or formed secondary potassium feldspar veinlets. Secondary biotite occurred mainly in phenocryst, matrix and veinlets, belong to magnesium-rich biotite formed under the conditions of high-oxidation magma- hydrothermal. Chloritization developed in all alteration zones and alterd iron- magnesium minerals such as biotite and hornblende and then formed chlorite veinlets. As the temperature rises, Si in the tetrahedral site of chlorite decreased, and chlorite component evolved from diabantite to ripiolite. The consistent 280℃~360℃ of formation temperature hinted that chlorite formed on the same temperature range in all alteration zones. However, formation temperature range of chlorite from the gypsum-carbonate-chlorite vein was 190℃~220℃, and it may be the product of the latest stage of hydrothermal activity. The closely relationship between biotite and rutile indicate that most of rutiles are precipitated in the process of biotite alteration and recrystallization. In addition, the V2O3 concentration of rutile from ore body in Duobuza gold-rich porphyry copper deposit is >0.4％, indicate that V concentration in rutile has important significance on marking main ore body of porphyry copper deposit. Apatites from Duobuza deposit all are F-rich. And apatite in the wall rock contained low MnO content and relatively high FeO content, which may due to the basaltic composition of the wall rocks. The MnO in apatite from altered porphyry show a strong positive correlation with FeO. In addition, Cl/F ratio of apatite from wall rock was highest, followed by the potassic alteration zone and potassic alteration zone overprinted by moderate argillization alteration was the lowest. SO2 in Apatite are in the scope of 0 to 0.66%, biotite in the apatite has the highest SO2, followed by the potassic alteration zone, potassic alteration zone overprinted by moderate argillization alteration, and the lowest in the surrounding rocks, which may be caused by the decrease of oxygen fugacity of hydrothermal fluid and S exhaust by sulfide precipitation in potassic alteration. Magnetite in the wall rock have higher Cr2O3 and lower Al2O3 features compared with altered porphyry, this may be due to basalt wall rock generally has high Cr content. And magnetites have higher TiO2 content in potassic alteration than moderate argillization alteration overprinted by potassic alteration, argillization and wall rock, suggested that its formation temperature in potassic alteration was the highest among them. The ore minerals mainly are chalcopyrite and bornite, and Au contents of chalcopyrite, bornite, and pyrite are similar with chalcopyrite slightly higher. The Eu* negative anomaly of disseminated chalcopyrite was relatively lower than chalcopyrite in veinlets. Within a drill hole, the Eu* negative anomaly of disseminated chalcopyrite was gradually larger from bottom to top. Magnetite has the same distribution model, with obvious negative Eu* abnormal, and ΣREE in great changes. The gypsum has the highest ΣREE content and the obvious negative anomaly, and biotite obviously has the Eu* abnormal. Based on the petrographic and geochemical characteristics, five series of magmatic rocks can be broadly classified; they are volcanic rocks of the normal island arc, high-Nb basaltic rocks, adakites, altered porphyry and diorite. The Sr, Nd, Hf isotopes and geochemistry of various series of magmatic rock show that they may be the result of mixing between basic magma and various degrees of acid magma coming from lower crust melted by high temperature basic underplating from partial melting of the subduction sediment melt metasomatic mantle wedge. Furthermore S isotope and Pb isotope of the sulfide, ore-bearing porphyries and volcanic rocks indicated ore-forming source is the mantle wedge metasomatied by subduction sediment melt. Oxygen fugacity of magma estimated by Fe2O3/FeO of whole rock and zircon Ce4+/Ce3+ indicated that the oxidation of basalt-andesitic rocks is higher than ore-forming porphyry, and might imply high-oxidation characteristics of underplated basic magma. Its high oxidative mechanism is likely mantle sources metasomatied by subduction sediment magma, including water and Fe3+. And such high oxidation of basaltic magma is conducive to the mantle of sulfides in the effective access to melt. And the An component of dark part within plagioclase phenocryst zoning belong to bytownite (An 74%), and its may be a result of magma composition changes refreshment by basaltic magma injection. SHRIMP zircon U-Pb and LA-ICP-MS zircon U-Pb geochronology study showed that the intrusions and volcanic rocks from Duobuza porphyry copper deposit belong to early Cretaceous magma series (126~105Ma). The magma evolution series are as follows: the earliest diorite and diorite porphyrite → ore-bearing porphyry and barren grandiorite porphyry →basaltic andesite → diorite porphyrite → andesite → basaltic andesite, and magma component shows a evolution trend from intermediate to intermediate-acid to basic. Based on the field evidences, the formation age of high-Nb basalt may be the latest. The Ar-Ar geochronology of altered secondary biotite, K-feldspar and sericite shows that the main mineralization lasting a interval of about 4 Ma, the duration limit of whole magma-hydrothermal evolution of about 6 Ma, and possibly such a long duration limit may result in the formation of Duobuza super-large copper deposit. Moreover, tectonic diagram and trace element geochemistry of volcanic rocks and diorite from Duobuza porphyry copper deposit confirm that it formed in a continental margin arc environment. Zircon U-Pb age of volcanic rocks and porphyry fall in the range of 105~121Ma, and Duobuza porphyry copper deposit locating in the north of the Bangonghu- Nujiang suture zone, suggested that Neo-Tethys ocean still subducted northward at least early Cretaceous, and its closure time should be later than 105 Ma. Three major inclusion types and ten subtypes are distinguished from quartz phenocrysts and various quartz veins. Vapor generally coexisting with brine inclusions, suggest that fluid boiling may be the main ore-forming mechanism. Raman spectrums of fluid inclusions display that the content of vapor and liquid inclusion mainly contain water, and vapor occasionally contain a little CO2. In addition, the component of liquid inclusions mainly include Cl-, SO42-, Na+, K+, a small amount of Ca2+, F-; and Cl- and Na+ show good correlation. Vapor mainly contains water, a small amount of CO2, CH4 and C2H6 and so on. The daughter minerals identified by Laman spectroscopy and SEM include gypsum, chalcopyrite, halite, sylvite, rutile, potassium feldspar, Fe-Mn-chloride and other minerals, and ore-forming fluid belong to a complex hydrothermal system containing H2O-NaCl-KClFeCl2CaCl2. H and O isotopic analysis of quartz phenocryst, vein quartz, magnetite, chlorite and gypsum from all alteration zones show that the ore-forming fluid of Duobuza gold-rich porphyry copper deposit consisted mainly of magmatic water, without addition of meteric water. Duobuza gold-rich porphyry copper deposit formed by the primary magmatic fluid (600-950C), which has high oxidation, ultra-high salinity and metallogenic element-rich, exsolution direct from the magma, and it is representative of the typical orthomagmatic end member of the porphyry continuum. Moreover, the fluid evolution model of Duobuza gold-rich porphyry copper deposit has been established. Furthermore, two key factors for formation of large Au-rich porphyry copper deposit have been summed up, which are ore-forming fluids earlier separated from magma and high oxidation magma-mineralization fluid system.

水热条件下钾长石碱性分解反应机理的实验研究

It is well known that our country is short of water-soluble potassium, but rich in insoluble potassium ores. Based on the work of the formers, using the orthogonal and monofactor experiments, the author optimized the production technology of micro-porous potassium silicon calcium mineral fertilizer by non-stirring hydrothermal chemical reaction when the alkaline earth booster CaO was available. The influences of temperature、time、reactant ratio and water-solid ratio on the dissolution rate of production’s elements were studied by orthogonal experiments, and the production technology was further optimized by monofactor experiments. By XRD、SEM、EDS and dissolving experiments, it was systematically studied that the effects of the reactant ratio、reaction time and reaction temperature on the properties of the production obtained by the hydrothermal reaction between KAlSi3O8 and CaO. The results showed that：when changing of the reaction condition, the reaction productions included tobermorite、 hibschite、α-C2SH and K2Ca(CO3)2; among which, K2Ca(CO3)2 was not the first production containing potassium, but K2Ca(CO3)2 was synthesized by the reaction among KOH、Ca(OH)2 and CO2. Whether the phase was synthesized was related to not only the reaction condition, but also their physicochemical properties; when the reaction condition was changed, the changes of different phases were different. The results of XRD and dissolution rate experiments explained the dissolution characteristic of every element of hydrothermal productions very well, and the relation between the dissolution rate of element and the phase of productions poured a good illumination on the production technology. The results of SEM and EDS showed that: hydrogarnet looked like spherical, and its surface was covered by some productions including K phase and Ca、Si phase; but the morphology of tobermorite was platy or lamellar or needlelike, and parts of Si in the structure of tobermorite were substituted by Al，and some K+ cations were inserted into the Ca interlayer of tobermorite at the same time. It was the first time that the interface between KAlSi3O8 and Ca(OH)2 was observed directly by SEM and EDS after the hydrothermal reaction, and the mechanism of hydrothermal reaction of KAlSi3O8 and Ca(OH)2 was further discussed. These results indicated that: the Ca-KAlSi3O8 intermediate compound was formed at first, and some K was released into the solution and KOH was produced at the same time; the C-S-H phase appeared before hydrogarnet, and then hydrogarnet was synthesized when the chemical reaction was carried on; if the reaction was carried on furthermore, α-C2SH、tobermorite and other C-S-H phases of different atom ratio appeared. The author found that the structure of KAlSi3O8 would be more drastically destroyed if there were some reactants, such as Ca(OH)2 which reacted with KAlSi3O8 and new phases were formed after the hydrothermal reaction between KAlSi3O8 and alkaline solution of equal ionic strength was finished. With the combination of calcination and hydrothermal reaction methods, the dissolution rate of products were greatly improved when the hydrothermal reaction was carried out after KAlSi3O8 and CaCO3 were calcined. Furthermore, the author has tentatively explored how to evaluate the effects of the differences of the activity of lime on the dissolution properties of hydrothermal products.